NL27WZ126 Dual Buffer with 3-State Outputs The NL27WZ126 is a high performance dual noninverting buffer operating from a 1.65 V to 5.5 V supply. Features • • • • • • • • • • • http://onsemi.com Extremely High Speed: tPD 2.6 ns (typical) at VCC = 5.0 V Designed for 1.65 V to 5.5 V VCC Operation Over Voltage Tolerant Inputs and Outputs LVTTL Compatible − Interface Capability With 5.0 V TTL Logic with VCC = 3.0 V LVCMOS Compatible 24 mA Balanced Output Sink and Source Capability Near Zero Static Supply Current Substantially Reduces System Power Requirements 3−State OE Input is Active−High Replacement for NC7WZ126 Chip Complexity = 72 FETs These Devices are Pb−Free and are RoHS Compliant MARKING DIAGRAM 8 M2 M G G US8 US SUFFIX CASE 493 1 M2 M G = Device Code = Date Code* = Pb−Free Package (Note: Microdot may be in either location) *Date Code orientation may vary depending upon manufacturing location. PIN ASSIGNMENT OE1 1 A1 8 2 Y2 OE2 7 3 GND VCC 6 4 Y1 5 A2 A1 EN 1 A2 OE 2 A1 3 Y2 4 GND 5 A2 6 Y1 7 OE2 8 VCC Output Input Y1 Y2 OE2 Function 1 FUNCTION TABLE Figure 1. Pinout (Top View) OE1 Pin OEn An Yn H H H H L L L X Z X = Don’t Care n = 1, 2 Figure 2. Logic Symbol ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. © Semiconductor Components Industries, LLC, 2012 April, 2012 − Rev. 8 1 Publication Order Number: NL27WZ126/D NL27WZ126 MAXIMUM RATINGS Symbol Value Units DC Supply Voltage −0.5 to +7.0 V VI DC Input Voltage −0.5 to +7.0 V VO DC Output Voltage −0.5 to +7.0 V IIK DC Input Diode Current VI < GND −50 mA IOK DC Output Diode Current VO < GND −50 mA VCC Parameter IO DC Output Sink Current ±50 mA ICC DC Supply Current per Supply Pin ±100 mA IGND DC Ground Current per Ground Pin ±100 mA TSTG Storage Temperature Range −65 to +150 °C TL Lead Temperature, 1 mm from Case for 10 Seconds 260 °C TJ Junction Temperature under Bias +150 °C qJA Thermal Resistance (Note 1) 250 °C/W PD Power Dissipation in Still Air at 85°C 250 mW MSL FR VESD Moisture Sensitivity Level 1 Flammability Rating Oxygen Index: 28 to 34 UL 94 V−0 @ 0.125 in ESD Withstand Voltage Human Body Model (Note 2) Machine Model (Note 3) Charged Device Model (Note 4) V > 2000 > 200 N/A Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm−by−1 inch, 2−ounce copper trace with no air flow. 2. Tested to EIA/JESD22−A114−A. 3. Tested to EIA/JESD22−A115−A. 4. Tested to JESD22−C101−A. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Units VCC Supply Voltage Operating Data Retention Only 1.65 1.5 5.5 5.5 VI Input Voltage (Note 5) 0 5.5 V VO Output Voltage (HIGH or LOW State) 0 5.5 V TA Operating Free−Air Temperature −40 +85 °C Dt/DV Input Transition Rise or Fall Rate VCC = 2.5 V ±0.2 V VCC = 3.0 V ±0.3 V VCC = 5.0 V ±0.5 V 0 0 0 20 10 5 5. Unused inputs may not be left open. All inputs must be tied to a high− or low−logic input voltage level. http://onsemi.com 2 V ns/V NL27WZ126 DC ELECTRICAL CHARACTERISTICS VCC Symbol Parameter VIH (V) Min High−Level Input Voltage 1.65 2.3 to 5.5 0.75 VCC 0.7 VCC VIL Low−Level Input Voltage 1.65 2.3 to 5.5 VOH High−Level Output Voltage VIN = VIH IOH = 100 mA IOH = −8 mA IOH = −12 mA IOH = −16 mA IOH = −24 mA IOH = −32 mA 1.65 to 5.5 1.65 2.7 3.0 3.0 4.5 VOL Low−Level Output Voltage VIN = VIH or VIL IOL = 100 mA IOL = 8 mA IOL = 12 mA IOL = 16 mA IOL = 24 mA IOL = 32 mA 1.65 to 5.5 1.65 2.7 3.0 3.0 4.5 IIN Condition TA = 255C Typ −405C 3 TA 3 855C Max Min Max 0.75 VCC 0.7 VCC 0.25 VCC 0.3 VCC VCC − 0.1 1.9 2.2 2.4 2.3 3.8 VCC 2.1 2.4 2.7 2.5 4.0 Units V 0.25 VCC 0.3 VCC VCC − 0.1 1.9 2.2 2.4 2.3 3.8 V V 0.1 0.3 0.4 0.4 0.55 0.55 0.1 0.3 0.4 0.4 0.55 0.55 V 0 to 5.5 ±0.1 ±1.0 mA 0 1 10 mA 0.20 0.22 0.28 0.38 0.42 Input Leakage Current VIN = 5.5V or GND IOFF Power Off Leakage Current VIN = 5.5V or VOUT = 5.5 V ICC Quiescent Supply Current VIN = 5.5V or GND 5.5 1 10 mA IOZ 3−State Output Leakage VIN = VIL or VIH 0 V ≤ VOUT ≤ 5.5 V 1.65 to 5.5 ±0.5 ±5 mA AC ELECTRICAL CHARACTERISTICS (tR = tF = 3.0 ns) VCC Symbol tPLH tPHL Parameter Propagation Delay AN to YN (Figures 3 and 4, Table 1) Condition TA = 255C Typ −405C 3 TA 3 855C (V) Min Max Min Max Units RL = 1 MW, CL = 15 pF 1.8 ± 0.15 2.5 ± 0.2 2.0 1.0 12 7.5 2.0 1.0 13 8 ns RL = 1 MW, CL = 15 pF RL = 500 W, CL = 50 pF 3.3 ± 0.3 0.8 1.2 5.2 5.7 0.8 1.2 5.5 6.0 RL = 1 MW, CL = 15 pF RL = 500 W, CL = 50 pF 5.0 ± 0.5 0.5 0.8 4.5 5.0 0.5 0.8 4.8 5.3 tOSLH tOSHL Output to Output Skew (Note 6) RL = 500 W, CL = 50 pF 3.3 ± 0.3 1.0 1.0 RL = 500 W, CL = 50 pF 5.0 ± 0.5 0.8 0.8 tPZH tPZL Output Enable Time (Figures 5, 6 and 7, Table 1) RL = 250 W, CL = 50 pF 1.8 ± 0.15 2.5 ± 0.2 3.0 1.8 14 8.5 3.0 1.8 15 9.0 3.3 ± 0.3 1.2 6.2 1.2 6.5 5.0 ± 0.5 0.8 5.5 0.8 5.8 1.8 ± 0.15 2.5 ± 0.2 2.5 1.5 12 8.0 2.5 1.5 13 8.5 3.3 ± 0.3 0.8 5.7 0.8 6.0 5.0 ± 0.5 0.3 4.7 0.3 5.0 tPHZ tPLZ Output Enable Time (Figures 5, 6 and 7, Table 1) RL & R1 = 500 W, CL = 50 pF ns ns ns 6. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device. This specification applies to any outputs switching in the same direction, either HIGH−to−LOW (tOSHL) or LOW−to−HIGH (tOSLH); parameter guaranteed by design. http://onsemi.com 3 NL27WZ126 CAPACITIVE CHARACTERISTICS Symbol CIN Parameter Condition Typical Units Input Capacitance VCC = 5.5 V, VI = 0 V or VCC 2.5 pF COUT Output Capacitance VCC = 5.5 V, VI = 0 V or VCC 2.5 pF CPD Power Dissipation Capacitance (Note 7) 10 MHz, VCC = 3.3 V, VI = 0 V or VCC 10 MHz, VCC = 5.5 V, VI = 0 V or VCC 9 11 pF 7. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no−load dynamic power consumption; PD = CPD VCC2 fin + ICC VCC. tf = 3 ns tf = 3 ns INPUT A and B 90% Vmi OE = GND VCC 90% INPUT Vmi 10% 10% tPHL OUTPUT CL * GND RL tPLH VOH OUTPUT Y Vmo Vmo *Includes all probe and jig capacitance. A 1 MHz square input wave is recommended for propagation delay tests. VOL Figure 3. Switching Waveform Figure 4. tPLH or tPHL 2.7 V Vmi Vmi OE 0V tPZH tPHZ VOH − 0.3 V Vmo On VCC ≈0V tPZL On tPLZ Vmo ≈ 3.0 V VOL + 0.3 V GND Figure 5. AC Output Enable and Disable Waveform http://onsemi.com 4 NL27WZ126 Table 1. Output Enable and Disable Times tR = tF = 2.5 ns, 10% to 90%; f = 1 MHz; tW = 500 nsv VCC Symbol 3.3 V + 0.3 V 2.7 V 2.5 V + 0.2 V Vmi 1.5 V 1.5 V VCC/2 Vmo 1.5 V 1.5 V VCC/2 2 INPUT VCC R1 = 500 W VCC INPUT OUTPUT CL = 50 pF OUTPUT CL = 50 pF RL = 500 W RL = 250 W A 1 MHz square input wave is recommended for propagation delay tests. A 1 MHz square input wave is recommended for propagation delay tests. Figure 6. tPZL or tPLZ Figure 7. tPZH or tPHZ DEVICE ORDERING INFORMATION Device Order Number NL27WZ126USG Package Type Shipping† US8 (Pb−Free) 3000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 5 NL27WZ126 PACKAGE DIMENSIONS US8 CASE 493−02 ISSUE B −X− A 8 −Y− 5 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION “A” DOES NOT INCLUDE MOLD FLASH, PROTRUSION OR GATE BURR. MOLD FLASH. PROTRUSION AND GATE BURR SHALL NOT EXCEED 0.140 MM (0.0055”) PER SIDE. 4. DIMENSION “B” DOES NOT INCLUDE INTER− LEAD FLASH OR PROTRUSION. INTER−LEAD FLASH AND PROTRUSION SHALL NOT E3XCEED 0.140 (0.0055”) PER SIDE. 5. LEAD FINISH IS SOLDER PLATING WITH THICKNESS OF 0.0076−0.0203 MM. (300−800 “). 6. ALL TOLERANCE UNLESS OTHERWISE SPECIFIED ±0.0508 (0.0002 “). J DETAIL E B L 1 4 R S G P U H C −T− SEATING PLANE 0.10 (0.004) M N 0.10 (0.004) T K D R 0.10 TYP T X Y V M F DETAIL E MILLIMETERS MIN MAX 1.90 2.10 2.20 2.40 0.60 0.90 0.17 0.25 0.20 0.35 0.50 BSC 0.40 REF 0.10 0.18 0.00 0.10 3.00 3.20 0_ 6_ 5_ 10 _ 0.23 0.34 0.23 0.33 0.37 0.47 0.60 0.80 0.12 BSC DIM A B C D F G H J K L M N P R S U V INCHES MIN MAX 0.075 0.083 0.087 0.094 0.024 0.035 0.007 0.010 0.008 0.014 0.020 BSC 0.016 REF 0.004 0.007 0.000 0.004 0.118 0.126 0_ 6_ 5_ 10 _ 0.010 0.013 0.009 0.013 0.015 0.019 0.024 0.031 0.005 BSC SOLDERING FOOTPRINT* 3.8 0.15 0.50 0.0197 1.8 0.07 0.30 0.012 1.0 0.0394 SCALE 8:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 http://onsemi.com 6 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NL27WZ126/D