HI-SINCERITY Spec. No. : IC200806 Issued Date : 2008.07.07 Revised Date : Page No. : 1/7 MICROELECTRONICS CORP. H34063BP / H34063BS DC-to-DC Converter Integrate Circuit Devices 8-Lead Plastic DIP-8 Package Code: P Description The H34063B Series is a monolithic control circuit containing the primary functions required for DC-to-DC converters. These devices consist of an internal temperature compensated reference, comparator, controlled duty cycle oscillator with an active current limit circuit, driver and high current output switch. This series was specifically by Avantics Microelectronics Corp. • 8-Lead Plastic SO-8 Package Code: S Features • 3V to 35V Input Voltage Operation • Internal 1.2A Peak Current Switch • Internal ±1.8% Reference • Low Quiescent Current at 1.6mA • Frequency Operation from 100Hz~100KHz • Output Voltage Adjustable • Active Current Limiting • Step-Up, Step-Down or Inverting Switching Regulators Pin Connections 8 1 7 2 6 3 5 Pin1: Switch Collector (SWC) Pin5: Comparator Inverting Input (FB) Pin2: Switch Emitter (SWE) Pin6: Voltage Supply (Vcc) Pin3: Timing Capacitor (TC) Pin7: Ipk Sense (Ipk) Pin4: Ground (GND) Pin8: Voltage Driver Collector (DRC) 4 Absolute MHium Rating Parameter Power Supply Voltage Comparator Input Voltage Range Symbol Value Unit VCC 35 V Vir -0.3~+35 V Switch Collector Voltage VC(SW) 35 V Switch Emitter Voltage VSWE 35 V Switch Emitter to Collector Voltage VCE 35 V VC(DR) 35 V Switch Current ISW 1.2 A Power Dissipation at TJ=20oC PD Operating Ambient Temperature Range Topr Driver Collector Voltage Storage Temperature Range Operating Junction Temperature Thermal Resistance Junction-ambient H34063BP, H34063BS Tstg Topj θJA DIP-8 1.25 SO-8 0.625 W 0~+70 o C -65~+150 o C 120 o C 125 o C/W HSMC Product Specification HI-SINCERITY Spec. No. : IC200806 Issued Date : 2008.07.07 Revised Date : Page No. : 2/7 MICROELECTRONICS CORP. Electrical Characteristics (VCC=5V,TA=0~70°C, unless otherwise specified) Parameter Symbol Test Condition Min. Typ. MH. Unit 10 25 42 uA 100 150 260 uA KHz Oscillator Charging Current VCC=5~35V, Ta=25oC Ichg Discharge Current o Idischg Frequency VCC=5~35V, Ta=25 C o fOSC Discharge to Charge Current Ratio Current Limit Sense Voltage VPIN5=0, CT=1nF, Ta=25 C 27 37 47 Idischg/Ichg VPIN7=VCC, Ta=25oC 5.2 6 7.5 VIPK Idischg=Ichg, Ta=25oC 250 300 350 mV Output Switch Saturation Voltage, Darlington Connection Saturation Voltage DC Current Gain VCE(sat) 1 ISW=1A, VC(SW)=VC(DR) - 1 1.3 V VCE(sat) 2 ISW=1A, IC(DR)=50mA - 0.4 0.7 V 35 120 - - 10 100 uA 1.227 1.25 1.273 V hFE Collector Off-State Current ICC(off) ISW=1A, VCE=5V VCE=35V, Ta=25oC Comparator Threshold Voltage VFB Threshold Voltage Line Regulation Input Bias Current ΔVFB VCC=5~35V - 1.5 10 mV IIB VIN=0V - 40 400 nA ICC VCC=5~35V, VPIN7=VCC, VPin5>VFB, CT=0.001uF, Pin7=GND, Remaining pins open - 1.6 4 mA Total Device Supply Current Block Diagram DRI Pin8: Driver Collector SC Pin1: 1.2A Switch Collector Q Q2 Q1 S R 80Ω SE Pin2: Darlington Switch Emitter IPK CT IPK Pin7: Highside Current Sense Input, VCC-VIPK=300mV Oscillator TC Pin3: Oscilletor Timing Capacitor Comparator 1.25V Reference Voltage GND Pin4: Power GND H34063BP, H34063BS VCC Pin6: Power Supply Input + FB Pin5: Feedback Comparator Inverting Input HSMC Product Specification HI-SINCERITY MICROELECTRONICS CORP. Spec. No. : IC200806 Issued Date : 2008.07.07 Revised Date : Page No. : 3/7 Application Information Design Formula Table Calculation Step-Down Step-Up Voltage-Inverting ton/toff (Vout+VF)/(Vin(min) -Vsat-Vout) (Vout+VF-Vin(min))/(Vin(min)-Vsat) (|Vout|+VF)/(Vin(mH)-Vsat) (ton+toff) mH 1/Fmin 1/Fmin 1/Fmin -5 -5 CT 4*10 ton 4*10 ton 4*10-5ton IC(sw) 2*Iout(mH) 2*Iout(mH)(ton+toff/toff) 2*Iout(mH)(ton+toff/toff) RS 0.3/IC(sw) 0.3/IC(sw) 0.3/IC(sw) L(min) (Vin(min)-Vsat/Ipk(sw))*ton(mH) (Vin(min)-Vsat/Ipk(sw))*ton(mH) (Vin(min)-Vsat/Ipk(sw))*ton(mH) CO (Ipk(sw)*(ton+toff))/(8*Vripple(P-P)) Iout*ton/Vripple(P-P) Iout*ton/Vripple(P-P) Vsat: Saturation voltage of the output switch. VF: Forward voltage drop of the ringback rectifier. The following power supply characteristics must be chosen: Vin: Nominal input voltage. Vout: Desired output voltage. |Vout|=1.25*(1+RB/RA) Iout: Desired output current Fmin: Minimum desired output switching frequency at the selected values for Vin and Iout. Vripple(P-P): Desired peak to peak output ripple voltage in practice, the calculated value will need to be increased due to the capacitor equivalent series resistance and board layout. The ripple voltage should be kept to a low value since it will directly effect the line and load regulation. H34063BP, H34063BS HSMC Product Specification HI-SINCERITY Spec. No. : IC200806 Issued Date : 2008.07.07 Revised Date : Page No. : 4/7 MICROELECTRONICS CORP. Characteristics Curve Current Sense Voltage vs Temperature Standby Supply Current vs Supply Voltage 550 2.4 450 Vcc=5.0V Ichg=Idischg 400 Icc(mA) Vipk(sense)(V) 500 350 300 2.0 1.6 1.2 Ct=1.0nF Pin7=Vcc Pin2=Gnd 0.8 250 200 0.4 150 0.0 -60 -40 -20 0 20 40 60 0 80 100 120 140 5 10 15 Ta(℃ ) 1.6 700 1.5 600 Vcc=5.0V Pins1,7,8=Vc c Pin3,5=Gnd Ta=25 ℃ 1.4 1.3 1.2 1.1 0.2 0.4 0.6 0.8 1 1.2 Vcc=5V Pin7=Vcc Pin5=Gnd 500 400 vs 1.4 toff 100 0.1 1 1.255 Vcc=5V Pin7=Vcc Pin2,3,5=Gnd Ta=25 ℃ Vref(V) 1.260 1.0 Vce(sat) Reference Voltage vs Temperature 1.2 0.4 10 Ct(nF) 1.4 0.6 ton 200 Emitter Current 0.8 40 Ta=25℃ Ie(A) Vce(sat) 35 300 0 0.01 1.0 0 30 Output Switch On-Off Time vs Oscillator Timing Capacitor ton ,toff(μs) Vce(sat)(V) Emitter Follower Configuration Output Saturation Voltage vs Emitter Current 20 25 Vcc(V) Vcc=5V 1.250 1.245 1.240 1.235 1.230 0.2 -50 -25 0 0.0 0 400 800 Ic(mA) H34063BP, H34063BS 1200 25 50 75 100 125 150 Tj(℃ ) HSMC Product Specification HI-SINCERITY Spec. No. : IC200806 Issued Date : 2008.07.07 Revised Date : Page No. : 5/7 MICROELECTRONICS CORP. Application Information (Continuos) Fig.2 Step-Up Converter D1 L1 Vout 28V / 200mA 200uH R1 150Ω H1N5819 H34063B RSC 0.22 Vin C1 100uF 8 1 7 2 6 3 5 4 Cout 220uF CT 680pF RB RA 2.2kΩ 47kΩ Line Regulation: 100mV (Vin=8V~16V, @IO=200mA) Load Regulation: 5mV (Vin=12V, @IO=80mA~200mA) Fig.3 Step-Up Converter With External NPN Switch L1 R1 RSC Vin C1 Vout D1 H34063B 8 1 7 2 6 3 5 4 Q1 CT Cout R2 RB RA Fig.4 Step-Down Converter L1 200uH H34063B RSC 0.25 Vin C1 100uF 8 1 7 2 6 3 5 4 D1 H1N5819 Vout 5V / 500mA Cout 470uF CT 470pF RB 3.6kΩ RA 1.2kΩ Line Regulation: 40mV (Vin=10V~20V, @IO=500mA) Load Regulation: 5mV (Vin=15V, @IO=10mA~500mA) Short Circuit Current: 1.3A (Vin=15V, @RL=0.1Ω H34063BP, H34063BS HSMC Product Specification HI-SINCERITY Spec. No. : IC200806 Issued Date : 2008.07.07 Revised Date : Page No. : 6/7 MICROELECTRONICS CORP. Fig.5 Step-Down Converter With External PNP Saturation Switch R1 H34063B RSC Vin 8 1 7 2 6 3 5 4 R2 Q1 L1 Vout CT D1 Cout RB C1 RA Fig.6 Voltage Inverting Converter D1 Vout -12V / 100mA H34063B RSC 0.25 Vin 4.5V-6V 8 1 7 2 6 3 5 4 C1 100uF H1N5819 L1 100uH Cout 470uF CT 680pF RA 953Ω RB 8.2kΩ Line Regulation: 20mV (Vin=4.5V~6V, @IO=100mA) Load Regulation: 100mV (Vin=5V, @IO=10mA~100mA) Fig.7 Voltage Inverting Converter With External PNP Saturation Switch H34063B RSC Vin 8 1 7 2 6 3 5 4 R2 R1 Q1 L1 D1 CT RA Vout C1 RB H34063BP, H34063BS Cout HSMC Product Specification HI-SINCERITY Spec. No. : IC200806 Issued Date : 2008.07.07 Revised Date : Page No. : 7/7 MICROELECTRONICS CORP. DIP-8 Dimension 8 6 7 DIM A B C D E F G H I J K L M α1 Marking: 5 A 1 2 3 4 B J F E C α1 K G Material: • Lead solder plating: Pure-Tin (Pb-free) • Mold Compound: Epoxy resin family, M H D I Pin Style: 1.SWC 2.SWE 3.TC 4.GND 5.FB 6.VCC 7.Ipk 8.DRC Min. 6.29 9.22 3.25 3.17 0.38 2.28 7.49 8.56 0.229 o 94 Max. 6.40 9.32 *1.52 *1.27 *0.99 3.35 3.55 0.53 2.79 7.74 *3.00 8.81 0.381 o 97 *: Typical, Unit: mm L 8-Lead DIP-8 Plastic Package AVANTICS Package Code: P SO-8 Dimension A DIM A B C D E F G H I J K L M N O Marking: G Pb Free Mark 7 8 B 6 5 C Pin1 Index 2 3 Pb-Free: " . " (Note) H Normal: None I Pin 1 Index Date Code H 4 Material: • Lead solder plating: Pure-Tin (Pb-free) • Mold Compound: Epoxy resin family, flammability solid burning class: UL94V-0 K E Part A Part A Control Code Pin Style: 1.SWC 2.SWE 3.TC 4.GND 5.FB 6.VCC 7.Ipk 8.DRC J D S 3 4 0 6 3 B M L N Min. 4.85 3.85 5.80 1.22 0.37 3.74 1.45 4.80 0.05 0.30 0.19 0.37 0.23 0.08 0.00 Max. 5.10 3.95 6.20 1.32 0.47 3.88 1.65 5.10 0.20 0.70 0.25 0.52 0.28 0.13 0.15 *: Typical, Unit: mm O F 8-Lead SO-8 Plastic Surface Mounted Package AVANTICS Package Code: S Important Notice: • All rights are reserved. Reproduction in whole or in part is prohibited without the prior written approval of HSMC. • HSMC reserves the right to make changes to its products without notice. • HSMC semiconductor products are not warranted to be suitable for use in Life-Support Applications, or systems. • HSMC assumes no liability for any consequence of customer product design, infringement of patents, or application assistance. Head Office And Factory: • Head Office (Hi-Sincerity Microelectronics Corp.): 10F.,No. 61, Sec. 2, Chung-Shan N. Rd. Taipei Taiwan R.O.C. Tel: 886-2-25212056 FH: 886-2-25632712, 25368454 H34063BP, H34063BS HSMC Product Specification