Six-Way SMT Power Divider DS56-0001 DS56-0001 Low Cost Six-Way SMT Power Divider 824 - 960 MHz Features • • • • • • • SOW-16 Pin 16 Small Size, Low Profile Superior Repeatability (Lot-to-lot Variation) Industry Standard SOW-16 SMT Plastic Package Typical Isolation: 25 dB Typical Insertion Loss: 0.3 dB Low Cost 1 Watt Power Handling Orientation Mark Pin 1 .0926-.1043 (7.40-7.60) .3977-.4133 (10.10-10.50) -A- Description M/A-COM’s DS56-0001 is an IC-based monolithic power divider in a low cost SOW-16 plastic package. This 6-way power divider is ideally suited for applications where PCB real estate is at a premium and part count reduction and cost are critical. Typical applications include base station switching networks and other cellular equipment, including subscriber units. Available in tape and reel. .394-.419 (10.00-10.65) .010(0.25) M B M -B- .010-.029 x 45 Chamfer (0.25-0.75) 0-8 .004 (0.10) -C- 0.050(1.27) BSC. .0040-.0118 (0.10-0.30) .016-.050 (0.40-1.27) .013-.020 TYP (0.33-0.51) .010(0.25) M C A M B S .0091-.0125 (0.23-0.32) 16-Lead SOP outline dimensions Wide body (.300) (All dimensions per JEDEC No. MS-013-AA, Issue C) Dimensions in ( ) are in mm. Unless Otherwise Noted: .xxx = 0.010 (.xx = 0.25) .xx = 0.02 (.x = 0.5) The DS56-0001 is fabricated using a passive-integrated circuit process. The process features full-chip passivation for increased performance and reliability. Ordering Information Part Number DS56-0001 DS56-0001-TR DS56-0001-RTR Package SOW 16-Lead Plastic Package 1 Forward Tape and Reel 1 Reverse Tape and Reel 1. If specific reel size is required, consult factory for part number assignment. 1 Typical Electrical Specifications , TA= +25ºC Parameters Insertion Loss Above 7.0 dB Isolation VSWR Amplitude Balance Phase Balance Units dB dB — dB ° Min. — 20 — — — Typ. 1.3 25 1.4:1 0.2 6 Max. 1.5 — 1.6:1 0.5 8 1. All specifications apply with a 50-ohm source and load impedance. V4.00 M/A-COM Division of AMP Incorporated ■ North America: Tel. (800) 366-2266, Fax (800) 618-8883 ■ Asia/Pacific: Tel.+85 2 2111 8088, Fax +85 2 2111 8087 ■ Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020 www.macom.com AMP and Connecting at a Higher Level are trademarks. Specifications subject to change without notice. Six-Way SMT Power Divider DS56-0001 1 3 Absolute Maximum Ratings Parameter Functional Diagram RF 3 (OUT) 1 Absolute Maximum 2 1W CW Input Power Operating Temperature -40°C to +85°C Storage Temperature -65°C to 150°C 1. Exceeding these limits may cause permanent damage. 2. With internal load dissipation of 0.125 W maximum. RF 4 (OUT) 16 GND 2 GND 15 RF 2 (OUT) RF 5 (OUT) 14 3 GND 4 GND 13 RF 1 (OUT) 5 Recommended PCB Configuration (Dimensions in Inches) .335 .093 TYP. .041 TYP. RF 3 RF 4 RF 2 RF 5 .067 TYP. RF 6 (OUT) 12 GND 6 GND 11 RF IN 7 GND 10 GND 8 GND 9 .030 TYP. RF 1 RF 6 3. Pins 2, 4, 6, 8, 9, 10, 11, 13, and 15 must be DC and RF grounded. .016 DIA. PLATE D THRU (21X) RF IN .050 DIA. PLATE D THRU (3X) .428 Typical Performance @ +25°C VSWR vs. Frequency 2 .0 -0.5 1 .8 VS W R IN SE RT IO N LO SS (dB) Insertion Loss vs. Frequency 0 -1.0 -1.5 1 .6 Input 1 .4 O utput 1 .2 -2.0 824 858 892 926 960 Frequency (M H z) 1 .0 824 858 892 926 960 Frequency (M H z) Isolation vs. Frequency IS OL ATIO N (dB ) 0 -10 -20 -30 -40 824 858 892 926 960 Frequency (M H z) V4.00 M/A-COM Division of AMP Incorporated ■ North America: Tel. (800) 366-2266, Fax (800) 618-8883 ■ Asia/Pacific: Tel.+85 2 2111 8088, Fax +85 2 2111 8087 ■ Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020 www.macom.com AMP and Connecting at a Higher Level are trademarks. Specifications subject to change without notice.