NCL30080 Product Preview Quasi-Resonant Primary Side Current-Mode Controller for LED Lighting The NCL30080 is a PWM current mode controller targeting isolated flyback and non−isolated constant current topologies. The controller operates in a quasi−resonant mode to provide high efficiency. Thanks to a novel control method, the device is able to precisely regulate a constant LED current from the primary side. This removes the need for secondary side feedback circuitry, biasing and an optocoupler. The device is highly integrated with a minimum number of external components. A wide VCC range simplifies the design process and allows a single design to support a wide LED forward voltage range. A robust suite of safety protection is built in to simplify the design. This device is specifically intended for very compact space efficient designs • • • • • 1 TSOP−6 SN SUFFIX CASE 318G MARKING DIAGRAM AAxAYWG G Features • • • • • • • • • • http://onsemi.com 1 Quasi−resonant Peak Current−mode Control Operation Primary Side Sensing (no optocoupler needed) AAx = Specific Device Code x = E or F Wide VCC Range A = Assembly Location Precise LED Constant Current Regulation ±1% Typical Y = Year Line Feed−forward for Enhanced Regulation Accuracy W = Work Week G = Pb−Free Package Low LED Current Ripple (Note: Microdot may be in either location) 250 mV ±2% Guaranteed Voltage Reference for Current Regulation ~ 0.9 Power Factor with Valley Fill Input Stage Low LED Current Ripple PIN CONNECTIONS 1 Source 300 mA / Sink 500 mA Totem Pole Driver with 12 V Gate ZCD VIN Clamp GND VCC Low Start−up Current (13 mA typ.) Small Space Saving Low Profile Package DRV CS Wide Temperature Range of −40 to +125°C (Top View) Pb−free, Halide−free MSL1 Product Robust Protection Features ♦ Over Voltage / LED Open Circuit Protection ♦ Secondary Diode Short Protection ♦ Output Short Circuit Protection Typical Applications ♦ Shorted Current Sense Pin Fault Detection • Integral LED Bulbs ♦ Latched and Auto−recoverable Versions • LED Power Driver Supplies ♦ Brown−out ♦ VCC Under Voltage Lockout • LED Light Engines ♦ Thermal Shutdown This document contains information on a product under development. ON Semiconductor reserves the right to change or discontinue this product without notice. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 21 of this data sheet. © Semiconductor Components Industries, LLC, 2013 January, 2013 − Rev. P0 1 Publication Order Number: NCL30080/D NCL30080 . . Aux . 1 6 2 5 3 4 Figure 1. Typical Application Schematic for NCL30080 Table 1. PIN FUNCTION DESCRIPTION Pin No Pin Name Function Pin Description 1 ZCD Zero Crossing Detection 2 GND − 3 CS Current sense This pin monitors the primary peak current 4 DRV Driver output The current capability of the totem pole gate drive (+0.3/−0.5 A) makes it suitable to effectively drive a broad range of power MOSFETs. 5 VCC Supplies the controller This pin is connected to an external auxiliary voltage. 6 VIN Input voltage sensing Brown−Out This pin observes the HV rail and is used in valley selection. This pin also monitors and protects for low mains conditions. Connected to the auxiliary winding; this pin detects the core reset event. The controller ground http://onsemi.com 2 NCL30080 VDD STOP Aux_SCP GND CS_shorted Internal Thermal Shutdown WOD_SCP VCC VCC Management VCC Over Voltage Protection BO_NOK VVIN VCC Clamp Circuit Zero Crossing Detection Valley Selection Aux. Winding Short Circuit Protection S Aux_SCP VVIN Q DRV Qdrv VVLY R Line Feedforward CS VCC_max Ipkmax Qdrv ZCD OFF UVLO Latch Fault Management VREF STOP VREF Leading Edge Blanking CS_reset Constant−Current Control Ipkmax VVIN Max. Peak Current Limit Ipkmax CS Short Protection CS_shorted Winding and Output diode Short Circuit Protection VVIN STOP VIN BO_NOK WOD_SCP Figure 2. Internal Circuit Architecture http://onsemi.com 3 Brown−Out NCL30080 Table 2. MAXIMUM RATINGS TABLE Symbol Rating Value Unit VCC(MAX) ICC(MAX) Maximum Power Supply voltage, VCC pin, continuous voltage Maximum current for VCC pin −0.3, +35 Internally limited V mA VDRV(MAX) IDRV(MAX) Maximum driver pin voltage, DRV pin, continuous voltage Maximum current for DRV pin −0.3, VDRV (Note 1) −500, +800 V mA VMAX IMAX Maximum voltage on low power pins (except pins DRV and VCC) Current range for low power pins (except pins ZCD, DRV and VCC) 0.3, +5.5 −2, +5 V mA VZCD(MAX) IZCD(MAX) Maximum voltage for ZCD pin Maximum current for ZCD pin −0.3, +10 −2, +5 V mA RθJ−A Thermal Resistance, Junction−to−Air 360 °C/W TJ(MAX) Maximum Junction Temperature 150 °C Operating Temperature Range −40 to +125 °C Storage Temperature Range −60 to +150 °C ESD Capability, HBM model (Note 2) 4 kV ESD Capability, MM model (Note 2) 200 V Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. VDRV is the DRV clamp voltage VDRV(high) when VCC is higher than VDRV(high). VDRV is VCC unless otherwise noted. 2. This device series contains ESD protection and exceeds the following tests: Human Body Model 4000 V per Mil−Std−883, Method 3015. 3. This device contains latch−up protection and exceeds 100 mA per JEDEC Standard JESD78 except for VIN pin which passes 60 mA. http://onsemi.com 4 NCL30080 Table 3. ELECTRICAL CHARACTERISTICS (Unless otherwise noted: For typical values TJ = 25°C, VCC = 12 V; For min/max values TJ = −40°C to +125°C, Max TJ = 150°C, VCC = 12 V) Description Test Condition Symbol Min Typ Max Unit VCC increasing VCC decreasing VCC decreasing VCC(on) VCC(off) VCC(HYS) VCC(reset) 16 8.2 8 3.5 18 8.8 – 4.5 20 9.4 – 5.5 Over Voltage Protection VCC OVP threshold VCC(OVP) 26 28 30 V VCC(off) noise filter VCC(reset) noise filter− tVCC(off) tVCC(reset) – – 5 20 – – ms ICC(start) – 13 30 mA ICC(sFault) – 46 60 mA ICC1 ICC2 ICC3 0.8 – – 1.0 2.15 2.6 1.4 4.0 5.0 Maximum Internal current limit VILIM 0.95 1 1.05 V Leading Edge Blanking Duration for VILIM (Tj = −25°C to 125°C) tLEB 250 300 350 ns Leading Edge Blanking Duration for VILIM (Tj = −40°C to 125°C) tLEB 240 300 350 ns Ibias – 0.02 – mA tILIM – 50 150 ns VCS(stop) 1.35 1.5 1.65 V tBCS – 120 – ns Blanking time for CS to GND short detection VpinVIN = 1 V tCS(blank1) 6 – 12 ms Blanking time for CS to GND short detection VpinVIN = 3.3 V tCS(blank2) 2 – 4 ms Drive Resistance DRV Sink DRV Source RSNK RSRC – – 13 30 – – Drive current capability DRV Sink (Note 4) DRV Source (Note 4) ISNK ISRC – – 500 300 – – STARTUP AND SUPPLY CIRCUITS V Supply Voltage Startup Threshold Minimum Operating Voltage Hysteresis VCC(on) – VCC(off) Internal logic reset Startup current Startup current in fault mode Supply Current Device Disabled/Fault Device Enabled/No output load on pin 4 Device Switching (Fsw = 65 kHz) mA VCC > VCC(off) Fsw = 65 kHz CDRV = 470 pF, Fsw = 65 kHz CURRENT SENSE Input Bias Current DRV high Propagation delay from current detection to gate off−state Threshold for immediate fault protection activation Leading Edge Blanking Duration for VCS(stop) GATE DRIVE W mA Rise Time (10% to 90%) CDRV = 470 pF tr – 40 – ns Fall Time (90% to 10%) CDRV = 470 pF tf – 30 – ns DRV minimum high level VCC = VCC(off)+0.2 V CDRV = 470 pF, RDRV = 33 kW VDRV(low) 8 – – V VCC = 30 V CDRV = 470 pF, RDRV = 33 kW VDRV(high) 10 12 14 V DRV high clamp level 4. Guaranteed by design http://onsemi.com 5 NCL30080 Table 3. ELECTRICAL CHARACTERISTICS (Unless otherwise noted: For typical values TJ = 25°C, VCC = 12 V; For min/max values TJ = −40°C to +125°C, Max TJ = 150°C, VCC = 12 V) Description Test Condition Symbol Min Typ Max Unit ZCD threshold voltage VZCD increasing VZCD(THI) 25 45 65 mV ZCD threshold voltage (Note 4) VZCD decreasing VZCD(THD) 5 25 45 mV ZCD hysteresis (Note 4) VZCD(HYS) 10 – – mV Threshold voltage for output short circuit or aux. winding short circuit detection VZCD(short) 0.8 1 1.2 V tOVLD 70 90 110 ms trecovery 3 4 5 s Ipin1 = 3.0 mA Ipin1 = −2.0 mA VCH VCL – −0.9 9.5 −0.6 – −0.3 VZCD decreasing tDEM – – 150 ns tPAR – 20 – ns tBLANK 2.25 3 3.75 ms tTIMO 5 6.5 8 ms Reference Voltage at Tj = 25°C VREF 245 250 255 mV Reference Voltage Tj = −40°C to 125°C VREF 242.5 250 257.5 mV VCS(low) 30 55 80 mV KLFF 15 17 19 mA/V VpinVIN = 4.5 V Ioffset(MAX) 67.5 76.5 85.5 mA Threshold for line range detection Vin increasing (1st to 2nd valley transition for VREF > 0.75 V) VVIN increasing VHL 2.28 2.4 2.52 V Threshold for line range detection Vin decreasing (2nd to 1st valley transition for VREF > 0.75 V) VVIN decreasing VLL 2.18 2.3 2.42 V tHL(blank) 15 25 35 ms TSHDN 130 155 170 °C TSHDN(HYS) – 55 – °C VBO(on) 0.90 1 1.10 V ZERO VOLTAGE DETECTION CIRCUIT Short circuit detection Timer VZCD < VZCD(short) Auto−recovery timer duration Input clamp voltage High state Low state Propagation Delay from valley detection to DRV high Equivalent time constant for ZCD input (Note 4) Blanking delay after on−time Timeout after last demag transition V CONSTANT CURRENT CONTROL Current sense lower threshold for detection of the leakage inductance reset time LINE FEED−FORWARD VVIN to ICS(offset) conversion ratio Offset current maximum value VALLEY SELECTION Blanking time for line range detection THERMAL SHUTDOWN Thermal Shutdown (Note 4) Device switching (FSW around 65 kHz) Thermal Shutdown Hysteresis (Note 4) BROWN−OUT Brown−Out ON level (IC start pulsing) VSD increasing Brown−Out OFF level (IC shuts down) VSD decreasing VBO(off) 0.85 0.9 0.95 V BO comparators delay tBO(delay) – 30 – ms Brown−Out blanking time tBO(blank) 35 50 65 ms Brown−Out pin bias current IBO(bias) −250 – 250 nA 4. Guaranteed by design http://onsemi.com 6 NCL30080 Application Information • Brown−Out: the controller includes a brown−out The NCL30080 implements a current−mode architecture operating in quasi−resonant mode. Thanks to proprietary circuitry, the controller is able to accurately regulate the secondary side current of the flyback converter without using any opto−coupler or measuring directly the secondary side current. • Quasi−Resonance Current−Mode Operation: implementing quasi−resonance operation in peak current−mode control, the NCL30080 optimizes the efficiency by switching in the valley of the MOSFET drain−source voltage. Thanks to a smart control algorithm, the controller locks−out in a selected valley and remains locked until the input voltage or the output current set point significantly changes. • Primary Side Constant Current Control: thanks to a proprietary circuit, the controller is able to compensate for the leakage inductance of the transformer and allow accurate control of the secondary side current. • Line Feed−forward: compensation for possible variation of the output current caused by system slew rate variation. • Open LED protection: if the voltage on the VCC pin exceeds an internal limit, the controller shuts down and waits 4 seconds before restarting switching. • • • circuit with a validation timer which safely stops the controller in the event that the input voltage is too low. The device will automatically restart if the line recovers. Cycle−by−cycle peak current limit: when the current sense voltage exceeds the internal threshold VILIM, the MOSFET is turned off for the rest of the switching cycle. Winding Short−Circuit Protection: an additional comparator with a short LEB filter (tBCS) senses the CS signal and stops the controller if VCS reaches 1.5 x VILIM. For noise immunity reasons, this comparator is enabled only during the main LEB duration tLEB. Output Short−circuit protection: If a very low voltage is applied on ZCD pin for 90 ms (nominal), the controllers assume that the output or the ZCD pin is shorted to ground and enters shutdown. The auto− restart version (B suffix) waits 4 seconds, then the controller restarts switching. In the latched version (A suffix), the controller is latched as long as VCC stays above the VCC(reset) threshold. http://onsemi.com 7 NCL30080 Constant Current Control Figure 3 shows the basic circuit of a flyback converter. Figure 4 portrays the primary and secondary current of a flyback converter operating in discontinuous conduction mode (DCM). Transformer Vbulk Lleak Cclp Nsp Rclp . Lp . Clamping network DRV Clump Rsense Figure 3. Basic Flyback Converter Schematic http://onsemi.com 8 Vout NCL30080 turned off, the drain voltage begins to oscillate because of the resonating network formed by the inductors (Lp+Lleak) and the lump capacitor. This voltage is reflected on the auxiliary winding wired in flyback mode. Thus, by monitoring the auxiliary winding voltage, we can detect the end of the conduction time of secondary diode. The constant current control block picks up the leakage inductor current, the end of conduction of the output rectifier and controls the drain current to maintain the output current constant. We have: During the on−time of the MOSFET, the bulk voltage Vbulk is applied to the magnetizing and leakage inductors Lp and Lleak and the current ramps up. When the MOSFET is turned−off, the inductor current first charges Clump. The output diode is off until the voltage across Lp reverses and reaches: N spǒV out ) V fǓ (eq. 1) The output diode current increase is limited by the leakage inductor. As a result, the secondary peak current is reduced: I D,pk t I L,pk I out + (eq. 2) N sp V REF 2N spR sense (eq. 3) The output current value is set by choosing the sense resistor: The diode current reaches its peak when the leakage inductor is reset. Thus, in order to accurately regulate the output current, we need to take into account the leakage inductor current. This is accomplished by sensing the clamping network current. Practically, a node of the clamp capacitor is connected to Rsense instead of the bulk voltage Vbulk. Then, by monitoring the voltage on the CS pin, we have an image of the primary current (red curve in Figure 4). When the diode conducts, the secondary current decreases linearly from ID,pk to zero. When the diode current has R sense + V ref 2N spI out (eq. 4) From Equation 3, the first key point is that the output current is independent of the inductor value. Moreover, the leakage inductance does not influence the output current value as the reset time is processed by the controller. IL,pk NspID,pk Ipri(t) Isec(t) time t1 t2 ton tdemag Vaux(t) time Figure 4. Flyback Currents and Auxiliary Winding Voltage in DCM http://onsemi.com 9 NCL30080 Internal Soft−Start At startup or after recovering from a fault, there is a small internal soft−start of 40 ms. In addition, during startup, as the output voltage is zero volts, the demagnetization time is long and the constant current control block will slowly increase the peak current towards its nominal value as the output voltage grows. Figure 5 shows a soft−start simulation example for a 9 W LED driver illustrating a natural soft startup. 16.0 (V) 12.0 1 Vout 2 I out 4 VControl 3 VCS 8.00 4.00 0 800m (A) 600m 400m 200m 0 800m (V) 600m 400m 200m 0 604u 1.47m 2.34m time in seconds 3.21m 4.07m Figure 5. Startup Simulation Showing the Natural Soft−start Cycle−by−Cycle Current Limit Winding and Output Diode Short−Circuit Protection When the current sense voltage exceeds the internal threshold VILIM, the MOSFET is turned off for the rest of the switching cycle (Figure 6). In parallel with the cycle−by−cycle sensing of the CS pin, another comparator with a reduced LEB (tBCS) and a higher threshold (1.5 V typical) is integrated to sense a winding short−circuit and immediately stops the DRV pulses. The controller goes into auto−recovery mode in version B. In version A, the controller is latched. In latch mode, the DRV pulses stop and VCC ramps up and down. The circuit un−latches when VCC pin voltage drops below VCC(reset) threshold. http://onsemi.com 10 NCL30080 S CS LEB1 Rsense + Vcontrol DRV Q Q latch R Vcc management PWMreset − + VCCstop UVLO grand 8_HICC reset Ipkmax − VILIMIT LEB2 aux Vdd OVP + STOP WOD_SCP − S VCS(stop) Q Q OVP OFF WOD_SCP latch S Q Q R 8_HICC R grand reset from Fault Management Block Figure 6. Winding Short Circuit Protection, Max. Peak Current Limit Circuits http://onsemi.com 11 VCC NCL30080 VCC Over Voltage Protection (Open LED Protection) In the NCL30080, when the VCC voltage reaches the VCC(OVP) threshold, the controller stops the DRV pulses and the 4−s timer starts counting. The IC re−start switching after the 4−s timer has elapsed as long as VCC ≥ VCC(on). This is illustrated in Figure 7. If no output load is connected to the LED string fails open circuited, the controller must be able to safely limit the output voltage excursion. 40.0 V CC(OVP) (V) 30.0 1 V CC V CC(on) 20.0 10.0 VCC(off) 0 40.0 (V) 30.0 2 Vout 20.0 10.0 0 800m (A) 600m 400m 200m 3 I out 0 8.00 (V) 6.00 4 OVP 4.00 2.00 0 1.38 3.96 6.54 time in seconds 9.11 Figure 7. Open LED Protection Chronograms http://onsemi.com 12 11.7 NCL30080 Valley Lockout valley until the input voltage varies significantly. This avoids valley jumping and the inherent noise caused by this phenomenon. The input voltage is sensed by the VIN pin. The internal logic selects the operating valley according to VIN pin voltage (line range detection in Figure 8). For a universal mains design, the controller operates in the first valley at low line and in the second valley at high line. Quasi−square wave resonant systems have a wide switching frequency excursion. The switching frequency increases when the output load decreases or when the input voltage increases. The switching frequency of such systems must be limited. The NCL30080 changes the valley as the input voltage increases. This limits the switching frequency excursion. Once a valley is selected, the controller stays locked in the Vbulk VIN + LLine 25−ms blanking time − 2.4 V if LLine low 2.3 V if LLine high Figure 8. Line Range Detection Table 4. VALLEY SELECTION VIN pin voltage for valley change VVIN decreases 0 −LL− 2.3 V 1st Valley number 0 −LL− −HL− 5V 2nd 2.4 V −HL− VVIN increases VIN pin voltage for valley change http://onsemi.com 13 5V HLine NCL30080 Zero Crossing Detection Block the valleys. To avoid such a situation, the NCL30080 features a time-out circuit that generates pulses if the voltage on ZCD pin stays below the VZCD(THD) threshold for 6.5 ms (nominal). The time-out also acts as a substitute clock for the valley detection and simulates a missing valley in case of very damped free oscillations. The ZCD pin detects when the drain-source voltage of the power MOSFET reaches a valley. A valley is detected when the voltage on pin 1 crosses below the VZCD(THD) internal threshold. At startup or in case of extremely damped free oscillations, the ZCD comparator may not be able to detect V ZCD 3 4 high V ZCD(THD) The 3rd valley is validated 14 2nd, 3rd low 12 The 3rd valley is not detected by the ZCD comp The 2nd valley is detected By the ZCD comparator high 15 ZCD comp low high low 16 TimeOut Time−out circuit adds a pulse to account for the missing 3rd valley high low 17 Clk Figure 9. Time−out Chronograms To avoid these scenarios, a protection circuit consisting of a comparator and secondary timer starts counting when the ZCD voltage is below the VZCD(short) threshold. If this timer reaches 90 ms, the controller detects a fault and shutdown. The auto−restart version (B suffix) waits 4 seconds, then the controller restarts switching. In the latched version (A suffix), the controller is latched as long as VCC stays above the VCC(reset) threshold. Normally with this type of time−out function, in the event the ZCD pin or the auxiliary winding is shorted, the controller could continue switching leading to improper regulation of the LED current. Moreover during an output short circuit, the controller will strive to maintain constant current operation. http://onsemi.com 14 NCL30080 Line Feed−forward Normally this error would increase if the input line voltage increased because the slew rate through the primary inductance would increase. To compensate for the peak current increase brought by the variation, a positive voltage proportional to the line voltage is added to the current sense signal. The amount of offset voltage can be adjusted using the RLFF resistor as shown in Figure 10. Because of internal and external propagation delays, the MOSFET is not turned−off immediately when the current set−point is reached. As a result, the primary peak current is slightly higher than expected resulting in a small output current error which can be compensated for during component selection. V CS(offset) + K LFFV pinVINR CS (eq. 5) The offset voltage is applied only during the MOSFET on−time. Bulk rail VDD VIN CS ICS(offset) RCS Rsense Q_drv Figure 10. Line Feed−forward Schematic Brown−out condition overrides the hiccup on VCC (VCC does not wait to reach VCC(off)) and the IC immediately goes into startup mode (ICC = ICC(start)). Note for most compact LED driver applications, if a true line dropout occurs, the energy in the input bulk capacitor will be discharged and the LED load will turn off before the 50 ms timer expires. In order to protect the supply against a very low input voltage, the NCL30080 features a brown−out circuit with a fixed ON/OFF threshold. The controller is allowed to start if a voltage higher than 1 V is applied to the VIN pin and shuts−down if the VIN pin voltage decreases and stays below 0.9 V for 50 ms nominal. Exiting a brown−out Vbulk VIN + 50−ms blanking time − 1 V if BONOK high 0.9 V if BONOK low Figure 11. Brown−out Circuit http://onsemi.com 15 BO_NOK NCL30080 160 (V) 120 VBulk 80.0 1 40.0 0 18.0 (V) 2 VCC(on) 16.0 14.0 VCC 12.0 VCC(off) 10.0 1.10 V BO(on) (V) 900m V BO(off) 700m V pinVIN 500m 3 300m 8.00 50−ms Timer (V) 6.00 BO_NOK low => Startup mode 4.00 2.00 BO_NOK 4 0 46.1m 138m 231m time in seconds 323m Figure 12. Brown−Out Chronograms (Valley Fill circuit is used) http://onsemi.com 16 415m NCL30080 CS Pin Short Circuit Protection power supply against a short circuit of the CS pin. When the MOSFET is on, if the CS voltage stays below VCS(low) after the adaptive blanking timer has elapsed, the controller shuts down and will attempt to restart on the next VCC hiccup. With a traditional controller, if the CS pin or the sense resistor is shorted to ground, the driver will not be able to turn off, leading to potential damage of the power supply. To avoid this, the NCL30080 features a circuit to protect the Adaptative Blanking Time VVIN Q_drv CS − S + VCS(low) Q CS_short Q R UVLO BO_NOK Figure 13. CS Pin Short Circuit Protection Schematic Fault Management In this mode, the DRV pulses are stopped. VCC voltage decrease through the controller own consumption (ICC1). For the output diode short circuit protection, the output / aux. winding short circuit protection and the VCC OVP, the controller waits 4 seconds (auto−recovery timer) and then initiates a startup sequence (VCC ≥ VCC(on)) before re−starting switching. Latch Mode This mode is activated by the output diode short−circuit protection (WOD_SCP) and the Aux_SCP in version A only. In this mode, the DRV pulses are stopped and the controller is latched. There are hiccups on VCC. The circuit un−latches when VCC < VCC(reset). OFF Mode The circuit turns off whenever a major condition prevents it from operating: • Incorrect feeding of the circuit: “UVLO high”. The UVLO signal becomes high when VCC drops below VCC(off) and remains high until VCC exceeds VCC(on). • VCC OVP • Output diode short circuit protection: “WOD_SCP high” • Output / Auxiliary winding Short circuit protection: “Aux_SCP high” • Die over temperature (TSD) • Brown−Out: “BO_NOK” high • Pin CS short circuited to GND: “CS_short high” http://onsemi.com 17 NCL30080 Reset Timer has finished counting VCC > VCC(on) VCC < VCC(off) or BO_NOK ↓ VCC_OVP BO_NOK high or TSD or CS_Short Stop 4−s Timer VCC Disch. BO_NOK high or TSD or CS_Short WOD_SCP or Aux_SCP or VCC_OVP Run With states: Reset Stop Run VCC Disch. 4−s Timer → → → → → VCC < VCC(off) Controller is reset, ICC = ICC(start) Controller is ON, DRV is not switching Normal switching No switching, ICC = ICC1, waiting for VCC to decrease to VCC(off) the auto−recovery timer is counting, VCC is ramping up and down between VCC(on) and VCC(off) Figure 14. State Diagram for B Version Faults http://onsemi.com 18 NCL30080 Reset Timer has finished counting VCC > VCC(on) VCC < VCC(off) or BO_NOK ↓ VCC < VCC(reset) 4−s Timer VCC_OVP BO_NOK high or TSD or CS_Short Stop VCC Disch. VCC_OVP BO_NOK high or TSD or CS_Short Latch Run WOD_SCP or Aux_SCP With states: Reset Stop Run VCC Disch. 4−s Timer Latch → → → → → → VCC < VCC(off) Controller is reset, ICC = ICC(start) Controller is ON, DRV is not switching Normal switching No switching, ICC = ICC1, waiting for VCC to decrease to VCC(off) the auto−recovery timer is counting, VCC is ramping up and down between VCC(on) and VCC(off) Controller is latched off, VCC is ramping up and down between VCC(on) and VCC(off), only VCC(reset) can release the latch. Figure 15. State Diagram for A Version Faults http://onsemi.com 19 NCL30080 PACKAGE DIMENSIONS TSOP−6 CASE 318G−02 ISSUE V D H 6 5 ÉÉ E1 1 NOTE 5 2 L2 4 GAUGE PLANE E 3 L b DETAIL Z e 0.05 A1 M A C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS D AND E1 DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE. DIMENSIONS D AND E1 ARE DETERMINED AT DATUM H. 5. PIN ONE INDICATOR MUST BE LOCATED IN THE INDICATED ZONE. SEATING PLANE DIM A A1 b c D E E1 e L L2 M c DETAIL Z MIN 0.90 0.01 0.25 0.10 2.90 2.50 1.30 0.85 0.20 0° MILLIMETERS NOM MAX 1.00 1.10 0.06 0.10 0.38 0.50 0.18 0.26 3.00 3.10 2.75 3.00 1.50 1.70 0.95 1.05 0.40 0.60 0.25 BSC 10° − RECOMMENDED SOLDERING FOOTPRINT* 6X 0.60 6X 3.20 0.95 0.95 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 20 NCL30080 OPTIONS Controller Output SCP Winding/Output Diode SCP NCL30080A Latched Latched NCL30080B Auto−recovery Auto−recovery ORDERING INFORMATION Device Package Marking Package Type Shipping† NCL30080ASNT1G AAE TSOP−6 (Pb−Free, Halide−Free) 3000 / Tape & Reel NCL30080BSNT1G AAF TSOP−6 (Pb−Free, Halide−Free) 3000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 http://onsemi.com 21 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCL30080/D