SN74CBT1G384 SINGLE FET BUS SWITCH www.ti.com SCDS065G – JULY 1998 – REVISED JUNE 2006 FEATURES • • 5-Ω Switch Connection Between Two Ports TTL-Compatible Control Input Levels DBV PACKAGE (TOP VIEW) A 1 B 2 GND 3 DCK PACKAGE (TOP VIEW) VCC 5 A 1 B 2 GND 3 5 VCC 4 OE OE 4 See mechanical drawings for dimensions. DESCRIPTION/ORDERING INFORMATION The SN74CBT1G384 features a single high-speed line switch. The switch is disabled when the output-enable (OE) input is high. ORDERING INFORMATION TA PACKAGE (1) SOT (SOT-23) – DBV –40°C to 85°C SOT (SC-70) – DCK (1) (2) TOP-SIDE MARKING (2) ORDERABLE PART NUMBER Reel of 3000 SN74CBT1G384DBVR Reel of 250 SN74CBT1G384DBVT Reel of 3000 SN74CBT1G384DCKR Reel of 250 SN74CBT1G384DCKT S8D_ S8_ Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. The actual top-side marking has one additional character that designates the assembly/test site. FUNCTION TABLE INPUT OE FUNCTION L A port = B port H Disconnect LOGIC DIAGRAM (POSITIVE LOGIC) 1 A 2 B 4 OE Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 1998–2006, Texas Instruments Incorporated SN74CBT1G384 SINGLE FET BUS SWITCH www.ti.com SCDS065G – JULY 1998 – REVISED JUNE 2006 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX VCC Supply voltage range –0.5 7 V VI Input voltage range (2) –0.5 7 V Continuous channel current IIK Input clamp current θJA Package thermal impedance (3) Tstg Storage temperature range (1) (2) (3) UNIT 128 mA VI/O < 0 –50 mA DBV package 206 DCK package 252 –65 °C/W °C 150 Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. The package thermal impedance is calculated in accordance with JESD 51-7. Recommended Operating Conditions (1) MIN MAX VCC Supply voltage 4 5.5 VIH High-level control input voltage 2 VIL Low-level control input voltage TA Operating free-air temperature (1) UNIT V V –40 0.8 V 85 °C All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. Electrical Characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK VCC = 4.5 V, II = –18 mA II VCC = 5.5 V, VI = 5.5 V or GND ICC VCC = 5.5 V, IO = 0, Ci Control input Cio(OFF) ron (2) VI = VCC or GND VI = 3 V or 0 OE = VCC VCC = 4 V, TYP at VCC = 4 V, VCC = 4.5 V 2 MAX V ±1 µA 1 µA VI = 0 pF 4 VI = 2.4 V, II = 15 mA UNIT –1.2 3 VO = 3 V or 0, VI = 2.4 V, (1) (2) MIN TYP (1) TEST CONDITIONS pF 14 20 II = 64 mA 5 7 II = 30 mA 5 7 II = 15 mA 10 15 Ω All typical values are at VCC = 5 V (unless otherwise noted), TA = 25°C. Measured by the voltage drop between the A and the B terminals at the indicated current through the switch. On-state resistance is determined by the lower voltage of the two (A or B) terminals. Submit Documentation Feedback SN74CBT1G384 SINGLE FET BUS SWITCH www.ti.com SCDS065G – JULY 1998 – REVISED JUNE 2006 Switching Characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) (1) VCC = 5 V ± 0.5 V VCC = 4 V FROM (INPUT) TO (OUTPUT) tpd (1) A or B B or A 0.35 0.25 ns ten OE A or B 5.5 1.6 4.9 ns tdis OE A or B 4.5 1 4.2 ns PARAMETER MIN MAX MIN UNIT MAX The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance, when driven by an ideal voltage source (zero output impedance). Submit Documentation Feedback 3 SN74CBT1G384 SINGLE FET BUS SWITCH www.ti.com SCDS065G – JULY 1998 – REVISED JUNE 2006 PARAMETER MEASUREMENT INFORMATION 7V S1 500 W From Output Under Test Open GND CL = 50 pF (see Note A) TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 7V Open 500 W 3V Output Control LOAD CIRCUIT 1.5 V 0V tPZL 3V Input 1.5 V 1.5 V 0V tPLH 1.5 V tPLZ 3.5 V 1.5 V tPZH VOH Output Output Waveform 1 S1 at 7 V (see Note B) tPHL 1.5 V VOL Output Waveform 2 S1 at Open (see Note B) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES 1.5 V VOL + 0.3 V VOL tPHZ VOH 1.5 V VOH - 0.3 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES NOTES: A . CL includes probe and jig capacitance. B . Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C . All input pulses are supplied by generators having the following characteristics: PRR £ 10 MHz, ZO = 50 W, tr £ 2.5 ns, tf £ 2.5 ns. D . The output is measured with one input transition per measurement. E . tPLZ and tPHZ are the same as tdis. H . tPZL and tPZH are the same as ten. G . tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms 4 Submit Documentation Feedback PACKAGE OPTION ADDENDUM www.ti.com 26-Mar-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) 74CBT1G384DBVRE4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (S8D2 ~ S8DG ~ S8DJ ~ S8DR) 74CBT1G384DBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (S8D2 ~ S8DG ~ S8DJ ~ S8DR) 74CBT1G384DBVTE4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (S8D2 ~ S8DR) 74CBT1G384DBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (S8D2 ~ S8DR) 74CBT1G384DCKRE4 ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (S83 ~ S8G ~ S8R ~ S8U) 74CBT1G384DCKRG4 ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (S83 ~ S8G ~ S8R ~ S8U) 74CBT1G384DCKTE4 ACTIVE SC70 DCK 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (S83 ~ S8R) 74CBT1G384DCKTG4 ACTIVE SC70 DCK 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (S83 ~ S8R) SN74CBT1G384DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (S8D2 ~ S8DG ~ S8DJ ~ S8DR) SN74CBT1G384DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (S8D2 ~ S8DR) SN74CBT1G384DCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (S83 ~ S8G ~ S8R ~ S8U) SN74CBT1G384DCKT ACTIVE SC70 DCK 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 (S83 ~ S8R) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 26-Mar-2013 Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 25-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) SN74CBT1G384DBVR SOT-23 DBV 5 3000 178.0 9.0 SN74CBT1G384DBVR SOT-23 DBV 5 3000 180.0 SN74CBT1G384DBVT SOT-23 DBV 5 250 180.0 SN74CBT1G384DCKR SC70 DCK 5 3000 SN74CBT1G384DCKT SC70 DCK 5 250 3.23 3.17 1.37 4.0 8.0 Q3 8.4 3.23 3.17 1.37 4.0 8.0 Q3 8.4 3.23 3.17 1.37 4.0 8.0 Q3 178.0 9.0 2.4 2.5 1.2 4.0 8.0 Q3 180.0 8.4 2.25 2.4 1.22 4.0 8.0 Q3 Pack Materials-Page 1 W Pin1 (mm) Quadrant PACKAGE MATERIALS INFORMATION www.ti.com 25-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74CBT1G384DBVR SOT-23 DBV 5 3000 180.0 180.0 18.0 SN74CBT1G384DBVR SOT-23 DBV 5 3000 202.0 201.0 28.0 SN74CBT1G384DBVT SOT-23 DBV 5 250 202.0 201.0 28.0 SN74CBT1G384DCKR SC70 DCK 5 3000 180.0 180.0 18.0 SN74CBT1G384DCKT SC70 DCK 5 250 202.0 201.0 28.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated