CY7C1329G 2-Mb (64K x 32) Pipelined Sync SRAM Features • Registered inputs and outputs for pipelined operation • 64K × 32 common I/O architecture • 3.3V core power supply • 2.5V I/O operation • Fast clock-to-output times counter for internal burst operation. All synchronous inputs are gated by registers controlled by a positive-edge-triggered Clock Input (CLK). The synchronous inputs include all addresses, all data inputs, address-pipelining Chip Enable (CE1), depth-expansion Chip Enables (CE2 and CE3), Burst Control inputs (ADSC, ADSP, and ADV), Write Enables (BW[A:D], and BWE), and Global Write (GW). Asynchronous inputs include the Output Enable (OE) and the ZZ pin. Addresses and chip enables are registered at rising edge of clock when either Address Strobe Processor (ADSP) or Address Strobe Controller (ADSC) are active. Subsequent burst addresses can be internally generated as controlled by the Advance pin (ADV). — 3.5 ns (for 166-MHz device) — 4.0 ns (for 133-MHz device) • Provide high-performance 3-1-1-1 access rate • User-selectable burst counter supporting Intel Pentium® interleaved or linear burst sequences Address, data inputs, and write controls are registered on-chip to initiate a self-timed Write cycle.This part supports Byte Write operations (see Pin Descriptions and Truth Table for further details). Write cycles can be one to four bytes wide as controlled by the Byte Write control inputs. GW when active LOW causes all bytes to be written. The CY7C1329G operates from a +3.3V core power supply while all outputs operate with a +2.5V supply. All inputs and outputs are JEDEC-standard JESD8-5-compatible. • Separate processor and controller address strobes • Synchronous self-timed writes • Asynchronous output enable • Offered in JEDEC-standard 100-pin TQFP package • “ZZ” Sleep Mode Option Functional Description[1] The CY7C1329G SRAM integrates 65,536 x 32 SRAM cells with advanced synchronous peripheral circuitry and a two-bit Logic Block Diagram A0, A1, A ADDRESS REGISTER 2 A[1:0] MODE ADV CLK Q1 BURST COUNTER CLR AND Q0 LOGIC ADSC ADSP BWD DQD BYTE WRITE REGISTER DQD BYTE WRITE DRIVER BWC DQC BYTE WRITE REGISTER DQC BYTE WRITE DRIVER DQB BYTE WRITE REGISTER DQB BYTE WRITE DRIVER BWB BWA BWE GW CE1 CE2 CE3 OE ZZ SENSE AMPS OUTPUT REGISTERS OUTPUT BUFFERS E DQs DQA BYTE WRITE DRIVER DQA BYTE WRITE REGISTER ENABLE REGISTER MEMORY ARRAY INPUT REGISTERS PIPELINED ENABLE SLEEP CONTROL 1 Note: 1. For best-practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com. Cypress Semiconductor Corporation Document #: 38-05393 Rev. *A • 3901 North First Street • San Jose, CA 95134 • 408-943-2600 Revised March 24, 2004 CY7C1329G Selection Guide 166 MHz 133 MHz Unit Maximum Access Time 3.5 4.0 ns Maximum Operating Current 240 225 mA Maximum CMOS Standby Current 40 40 mA Shaded area contains advance information. Please contact your local Cypress sales representative for availability of this part. BYTE C 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 100-pin TQFP CY7C1329G 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 NC DQB DQB VDDQ VSSQ DQB DQB DQB DQB VSSQ VDDQ DQB DQB VSS NC VDD ZZ DQA DQA VDDQ VSSQ DQA DQA DQA DQA VSSQ VDDQ DQA DQA NC BYTE B BYTE A MODE A A A A A1 A0 NC NC VSS VDD NC NC A A A A A A NC 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 BYTE D NC DQC DQC VDDQ VSSQ DQC DQC DQC DQC VSSQ VDDQ DQC DQC NC VDD NC VSS DQD DQD VDDQ VSSQ DQD DQD DQD DQD VSSQ VDDQ DQD DQD NC 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 A A CE1 CE2 BWD BWC BWB BWA CE3 VDD VSS CLK GW BWE OE ADSC ADSP ADV A A Pin Configuration Document #: 38-05393 Rev. *A Page 2 of 16 CY7C1329G Pin Definitions Name TQFP I/O Description A0, A1, A 37,36, 32,33,34, 35,44,45, 46,47,48, 49,81,82, 99,100 InputSynchronous Address Inputs used to select one of the 64K address locations. Sampled at the rising edge of the CLK if ADSP or ADSC is active LOW, and CE1, CE2, and CE3 are sampled active. A1, A0 feed the 2-bit counter. BWA, BWB, BWC, BWD 93,94,95, 96 InputSynchronous Byte Write Select Inputs, active LOW. Qualified with BWE to conduct Byte Writes to the SRAM. Sampled on the rising edge of CLK. GW 88 InputSynchronous Global Write Enable Input, active LOW. When asserted LOW on the rising edge of CLK, a global Write is conducted (ALL bytes are written, regardless of the values on BW[A:D] and BWE). BWE 87 InputSynchronous Byte Write Enable Input, active LOW. Sampled on the rising edge of CLK. This signal must be asserted LOW to conduct a Byte Write. CLK 89 InputClock Clock Input. Used to capture all synchronous inputs to the device. Also used to increment the burst counter when ADV is asserted LOW, during a burst operation. 98 InputSynchronous Chip Enable 1 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE2 and CE3 to select/deselect the device. ADSP is ignored if CE1 is HIGH. CE2 97 InputSynchronous Chip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction with CE1 and CE3 to select/deselect the device. CE3 92 InputSynchronous Chip Enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE1 and CE2 to select/deselect the device. Not connected for BGA. Where referenced, CE3 is assumed active throughout this document for BGA. OE 86 InputAsynchronous Output Enable, asynchronous input, active LOW. Controls the direction of the I/O pins. When LOW, the I/O pins behave as outputs. When deasserted HIGH, I/O pins are three-stated, and act as input data pins. OE is masked during the first clock of a Read cycle when emerging from a deselected state. ADV 83 InputSynchronous Advance Input signal, sampled on the rising edge of CLK, active LOW. When asserted, it automatically increments the address in a burst cycle. 84 InputSynchronous Address Strobe from Processor, sampled on the rising edge of CLK, active LOW. When asserted LOW, A is captured in the address registers. A1, A0 are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. ASDP is ignored when CE1 is deasserted HIGH. ADSC 85 InputSynchronous Address Strobe from Controller, sampled on the rising edge of CLK, active LOW. When asserted LOW, A is captured in the address registers. A1, A0 are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. ZZ 64 InputAsynchronous ZZ “sleep” Input, active HIGH. This input, when HIGH places the device in a non-time-critical “sleep” condition with data integrity preserved. For normal operation, this pin has to be LOW or left floating. ZZ pin has an internal pull-down. DQA, DQB DQC, DQD 52,53,56,57, 58,59,62,63, 68,69,72,73, 74,75,78,79, 2,3,6,7,8,9, 12,3,18,19, 22,23,24,25, 28,29 I/OSynchronous Bidirectional Data I/O lines. As inputs, they feed into an on-chip data register that is triggered by the rising edge of CLK. As outputs, they deliver the data contained in the memory location specified by “A” during the previous clock rise of the Read cycle. The direction of the pins is controlled by OE. When OE is asserted LOW, the pins behave as outputs. When HIGH, DQ are placed in a three-state condition. CE1 ADSP Document #: 38-05393 Rev. *A Page 3 of 16 CY7C1329G Pin Definitions (continued) Name TQFP I/O VDD 15,41,65,91 Power Supply VSS 17,40,67,90 Ground VDDQ 4,11,20, 27,54,61, 70,77 VSSQ 5,10,21, 26,55,60,71, 76 MODE 31 NC 1,14,16,30, 38,39,42,43, 50,51,66,80 Description Power supply inputs to the core of the device. Ground for the core of the device. I/O Power Supply Power supply for the I/O circuitry. I/O Ground InputStatic Ground for the I/O circuitry. Selects Burst Order. When tied to GND selects linear burst sequence. When tied to VDD or left floating selects interleaved burst sequence. This is a strap pin and should remain static during device operation. Mode Pin has an internal pull-up. No Connects. Not internally connected to the die. Functional Overview All synchronous inputs pass through input registers controlled by the rising edge of the clock. All data outputs pass through output registers controlled by the rising edge of the clock. The CY7C1329G supports secondary cache in systems utilizing either a linear or interleaved burst sequence. The interleaved burst order supports Pentium and i486 processors. The linear burst sequence is suited for processors that utilize a linear burst sequence. The burst order is user selectable, and is determined by sampling the MODE input. Accesses can be initiated with either the Processor Address Strobe (ADSP) or the Controller Address Strobe (ADSC). Address advancement through the burst sequence is controlled by the ADV input. A two-bit on-chip wraparound burst counter captures the first address in a burst sequence and automatically increments the address for the rest of the burst access. Byte Write operations are qualified with the Byte Write Enable (BWE) and Byte Write Select (BW[A:D]) inputs. A Global Write Enable (GW) overrides all Byte Write inputs and writes data to all four bytes. All Writes are simplified with on-chip synchronous self-timed Write circuitry. Three synchronous Chip Selects (CE1, CE2, CE3) and an asynchronous Output Enable (OE) provide for easy bank selection and output three-state control. ADSP is ignored if CE1 is HIGH. Single Read Accesses This access is initiated when the following conditions are satisfied at clock rise: (1) ADSP or ADSC is asserted LOW, (2) CE1, CE2, CE3 are all asserted active, and (3) the Write signals (GW, BWE) are all deasserted HIGH. ADSP is ignored if CE1 is HIGH. The address presented to the address inputs (A) is stored into the address advancement logic and the address register while being presented to the memory array. The corresponding data is allowed to propagate to the input of the output registers. At the rising edge of the next clock the data is allowed to propagate through the output register and onto the data bus within tCO if OE is active LOW. The only Document #: 38-05393 Rev. *A exception occurs when the SRAM is emerging from a deselected state to a selected state, its outputs are always three-stated during the first cycle of the access. After the first cycle of the access, the outputs are controlled by the OE signal. Consecutive single Read cycles are supported. Once the SRAM is deselected at clock rise by the chip select and either ADSP or ADSC signals, its output will three-state immediately. Single Write Accesses Initiated by ADSP This access is initiated when both of the following conditions are satisfied at clock rise: (1) ADSP is asserted LOW, and (2) CE1, CE2, CE3 are all asserted active. The address presented to A is loaded into the address register and the address advancement logic while being delivered to the RAM array. The Write signals (GW, BWE, and BW[A:D]) and ADV inputs are ignored during this first cycle. ADSP-triggered Write accesses require two clock cycles to complete. If GW is asserted LOW on the second clock rise, the data presented to the DQ inputs is written into the corresponding address location in the memory array. If GW is HIGH, then the Write operation is controlled by BWE and BW[A:D] signals. The CY7C1329G provides Byte Write capability that is described in the Write Cycle Descriptions table. Asserting the Byte Write Enable input (BWE) with the selected Byte Write (BW[A:D]) input, will selectively write to only the desired bytes. Bytes not selected during a Byte Write operation will remain unaltered. A synchronous self-timed Write mechanism has been provided to simplify the Write operations. Because the CY7C1329G is a common I/O device, the Output Enable (OE) must be deasserted HIGH before presenting data to the DQ inputs. Doing so will three-state the output drivers. As a safety precaution, DQs are automatically three-stated whenever a Write cycle is detected, regardless of the state of OE. Single Write Accesses Initiated by ADSC ADSC Write accesses are initiated when the following conditions are satisfied: (1) ADSC is asserted LOW, (2) ADSP is deasserted HIGH, (3) CE1, CE2, CE3 are all asserted active, Page 4 of 16 CY7C1329G and (4) the appropriate combination of the Write inputs (GW, BWE, and BW[A:D]) are asserted active to conduct a Write to the desired byte(s). ADSC-triggered Write accesses require a single clock cycle to complete. The address presented to A is loaded into the address register and the address advancement logic while being delivered to the memory array. The ADV input is ignored during this cycle. If a global Write is conducted, the data presented to DQ is written into the corresponding address location in the memory core. If a Byte Write is conducted, only the selected bytes are written. Bytes not selected during a Byte Write operation will remain unaltered. A synchronous self-timed Write mechanism has been provided to simplify the Write operations. Because the CY7C1329G is a common I/O device, the Output Enable (OE) must be deasserted HIGH before presenting data to the DQ inputs. Doing so will three-state the output drivers. As a safety precaution, DQs are automatically three-stated whenever a Write cycle is detected, regardless of the state of OE. Interleaved Burst Address Table (MODE = Floating or VDD) First Address A1, A0 Second Address A1, A0 Third Address A1, A0 Fourth Address A1, A0 00 01 10 11 01 00 11 10 10 11 00 01 11 10 01 00 Linear Burst Address Table (MODE = GND) First Address A1, A0 Second Address A1, A0 Third Address A1, A0 Fourth Address A1, A0 00 01 10 11 01 10 11 00 Burst Sequences 10 11 00 01 The CY7C1329G provides a two-bit wraparound counter, fed by A1, A0, that implements either an interleaved or linear burst sequence. The interleaved burst sequence is designed specifically to support Intel Pentium applications. The linear burst sequence is designed to support processors that follow a linear burst sequence. The burst sequence is user selectable through the MODE input. 11 00 01 10 Asserting ADV LOW at clock rise will automatically increment the burst counter to the next address in the burst sequence. Both Read and Write burst operations are supported. Sleep Mode The ZZ input pin is an asynchronous input. Asserting ZZ places the SRAM in a power conservation “sleep” mode. Two clock cycles are required to enter into or exit from this “sleep” mode. While in this mode, data integrity is guaranteed. Accesses pending when entering the “sleep” mode are not considered valid nor is the completion of the operation guaranteed. The device must be deselected prior to entering the “sleep” mode. CE1, CE2, CE3, ADSP, and ADSC must remain inactive for the duration of tZZREC after the ZZ input returns LOW. ZZ Mode Electrical Characteristics Parameter Description Test Conditions IDDZZ Snooze mode standby current ZZ > VDD – 0.2V tZZS Device operation to ZZ ZZ > VDD – 0.2V tZZREC ZZ recovery time ZZ < 0.2V tZZI ZZ Active to snooze current This parameter is sampled tRZZI ZZ Inactive to exit snooze current This parameter is sampled Document #: 38-05393 Rev. *A Min. Max. Unit 40 mA 2tCYC ns 2tCYC ns 2tCYC 0 ns ns Page 5 of 16 CY7C1329G Truth Table[2, 3, 4, 5, 6, 7] Next Cycle Add. Used Add. Used CE2 X CE3 X ZZ L ADSP X ADSC L ADV X WRITE X OE X L X X X X Unselected None None CE1 H Unselected None None L L X L Unselected None None L X H L L X X X X Unselected None None L L X L H L X X X Unselected None None L X H L H L X X X Begin Read External None X X X H X X X X X Begin Read External External L H L L L X X X L Continue Read Next External L H L L L X X X H Continue Read Next External L H L L H L X L X Continue Read Next External L H L L H L X H L Continue Read Next External L H L L H L X H H Suspend Read Current Next X X X L H H L H L Suspend Read Current Suspend Read Current Next X X X L H H L H H Suspend Read Current Next H X X L X H L H L Begin Write Current Next H X X L X H L H H Begin Write Current Next X X X L H H L L X Begin Write External Next H X X L X H L L X Continue Write Next Current X X X L H H H H L Continue Write Next Current X X X L H H H H H Suspend Write Current Current H X X L X H H H L Suspend Write Current Current H X X L X H H H H ZZ “Sleep” None Current X X X L H H H L X Truth Table for Read/Write [2, 3] Function Read GW H BWE H BWD X BWC X BWB X BWA X Read H L H H H H Write Byte A – DQA Write Byte B – DQB H L H H H L H L H H L H Write Bytes B, A H L H H L L Write Byte C – DQC H L H L H H Write Bytes C, A H L H L H L Write Bytes C, B H L H L L H Write Bytes C, B, A H L H L L L Write Byte D – DQD H L L H H H Write Bytes D, A H L L H H L Notes: 2. X = “Don't Care.” H =Logic HIGH, L = Logic LOW. 3. WRITE = L when any one or more Byte Write Enable signals (BWA,BWB,BWC,BWD) and BWE = L or GW = L. WRITE = H when all Byte Write Enable signals (BWA,BWB,BWC,BWD), BWE, GW = H. 4. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock. 5. CE1, CE2, and CE3 are available only in the TQFP package. 6. The SRAM always initiates a read cycle when ADSP is asserted, regardless of the state of GW, BWE, or BW[A:D]. Writes may occur only on subsequent clocks after the ADSP or with the assertion of ADSC. As a result, OE must be driven HIGH prior to the start of the Write cycle to allow the outputs to Three-State. OE is a don't care for the remainder of the Write cycle. 7. OE is asynchronous and is not sampled with the clock rise. It is masked internally during Write cycles. During a Read cycle all data bits are Three-State when OE is inactive or when the device is deselected, and all data bits behave as output when OE is active (LOW). Document #: 38-05393 Rev. *A Page 6 of 16 CY7C1329G Truth Table for Read/Write (continued)[2, 3] Function Write Bytes D, B GW H BWE L BWD L BWC H BWB L BWA H Write Bytes D, B, A H L L H L L Write Bytes D, C H L L L H H Write Bytes D, C, A H L L L H L Write Bytes D, C, B H L L L L H Write All Bytes H L L L L L Write All Bytes L X X X X X Document #: 38-05393 Rev. *A Page 7 of 16 CY7C1329G Maximum Ratings Current into Outputs (LOW)......................................... 20 mA (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ................................. –65°C to +150°C Static Discharge Voltage........................................... >2001V (per MIL-STD-883, Method 3015) Latch-up Current..................................................... >200 mA Ambient Temperature with Power Applied............................................. –55°C to +125°C Operating Range Supply Voltage on VDD Relative to GND........ –0.5V to +4.6V Range Commercial DC Voltage Applied to Outputs in Three-State ..................................... –0.5V to VDDQ + 0.5V Ambient Temperature 0°C to +70°C VDD 3.3V –5%/+10% VDDQ 2.5V –5% to +5% DC Input Voltage....................................–0.5V to VDD + 0.5V Electrical Characteristics Over the Operating Range[8, 9] Parameter Description Test Conditions Min. Max. Unit 3.135 3.6 V 2.375 2.625 V VDD Power Supply Voltage VDDQ I/O Supply Voltage VOH Output HIGH Voltage VDDQ = 2.5V, VDD = Min., IOH = –1.0 mA VOL Output LOW Voltage VDDQ = 2.5V, VDD = Min., IOL = 1.0 mA 0.4 V VIH Input HIGH Voltage[8] VDDQ = 2.5V 1.7 VDD + 0.3V V VIL Input LOW Voltage[8] VDDQ = 2.5V –0.3 0.7 V IX Input Load Current except ZZ and MODE –5 5 µA GND ≤ VI ≤ VDDQ Input Current of MODE Input = VSS 2.0 5 Input = VSS Input = VDD Output Leakage Current GND ≤ VI ≤ VDDQ, Output Disabled IDD VDD Operating Supply Current VDD = Max., IOUT = 0 mA, f = fMAX = 1/tCYC 7.5-ns cycle,133 MHz Automatic CS Power-down Current—TTL Inputs VDD = Max, Device Deselected, 6-ns cycle, 166 MHz VIN ≥ VIH or VIN ≤ VIL 7.5-ns cycle,133 MHz f = fMAX = 1/tCYC –5 6-ns cycle, 166 MHz µA µA –5 IOZ ISB1 µA –30 Input = VDD Input Current of ZZ V 30 µA 5 µA 240 mA 225 mA 100 mA 90 mA ISB2 Automatic CS VDD = Max, Device Deselected, All speeds Power-down VIN ≤ 0.3V or Current—CMOS Inputs VIN > VDDQ – 0.3V, f = 0 40 mA ISB3 Automatic CS VDD = Max, Device Deselected, 6-ns cycle, 166 MHz Power-down or VIN ≤ 0.3V or 7.5-ns cycle,133MHz Current—CMOS Inputs VIN > VDDQ – 0.3V, f = fMAX = 1/tCYC 85 mA 75 mA Automatic CS Power-down Current—TTL Inputs 45 mA ISB4 VDD = Max, Device Deselected, All speeds VIN ≥ VIH or VIN ≤ VIL, f = 0 Notes: 8. Overshoot: VIH(AC) < VDD +1.5V (Pulse width less than tCYC/2), undershoot: VIL(AC) > –2V (Pulse width less than tCYC/2). 9. TPower-up: Assumes a linear ramp from 0v to VDD(min.) within 200 ms. During this time VIH < VDD and VDDQ < VDD Document #: 38-05393 Rev. *A Page 8 of 16 CY7C1329G Thermal Resistance[10] Parameter Description ΘJA Thermal Resistance (Junction to Ambient) ΘJC Thermal Resistance (Junction to Case) Test Conditions TQFP Package Unit 41.83 °C/W 9.99 °C/W Test conditions follow standard test methods and procedures for measuring thermal impedance, per EIA/JESD51 Capacitance[10] Parameter Description CIN Input Capacitance CCLK Clock Input Capacitance CI/O Input/Output Capacitance Test Conditions Max. Unit TA = 25°C, f = 1 MHz, VDD = 3.3V VDDQ = 2.5V 5 pF 5 pF 5 pF AC Test Loads and Waveforms 2.5V I/O Test Load R = 1667Ω 2.5V OUTPUT OUTPUT RL = 50Ω Z0 = 50Ω VL = 1.25V 10% GND 5 pF INCLUDING JIG AND SCOPE (a) ALL INPUT PULSES VDDQ R =1538Ω 90% 10% 90% ≤ 1 ns ≤ 1 ns (b) (c) Switching Characteristics Over the Operating Range [11, 12] 166 MHz Parameter tPOWER Description VDD(Typical) to the First Access[13] Min. Max 133 MHz Min. Max Unit 1 1 ms Clock tCYC Clock Cycle Time 6.0 7.5 ns tCH Clock HIGH 2.5 3.0 ns tCL Clock LOW 2.5 3.0 ns Output Times tCO Data Output Valid after CLK Rise tDOH Data Output Hold after CLK Rise tCLZ Clock to Low-Z[14, 15, 16] tCHZ Clock to High-Z[[14, 15, 16] 3.5 4.0 ns OE LOW to Output Valid OE LOW to Output Low-Z[14, 15, 16] 3.5 4.5 ns 4.0 ns tOEV tOELZ tOEHZ 3.5 4.0 ns 0.5 0.5 ns 0 0 ns 0 [14, 15, 16] 0 3.5 OE HIGH to Output High-Z ns Set-up Times tAS Address Set-up before CLK Rise 1.5 1.5 ns tADS ADSC, ADSP Set-up before CLK Rise 1.5 1.5 ns Notes: 10. Tested initially and after any design or process change that may affect these parameters. 11. Timing reference level is 1.25V when VDDQ = 2.5V. 12. Test conditions shown in (a) of AC Test Loads unless otherwise noted. 13. This part has a voltage regulator internally; tPOWER is the time that the power needs to be supplied above VDD(minimum) initially before a Read or Write operation can be initiated. 14. tCHZ, tCLZ,tOELZ, and tOEHZ are specified with AC test conditions shown in part (b) of AC Test Loads. Transition is measured ± 200 mV from steady-state voltage. 15. At any given voltage and temperature, tOEHZ is less than tOELZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to achieve High-Z prior to Low-Z under the same system conditions. 16. This parameter is sampled and not 100% tested. Document #: 38-05393 Rev. *A Page 9 of 16 CY7C1329G Switching Characteristics Over the Operating Range (continued)[11, 12] 166 MHz Parameter Min. ADV Set-up before CLK Rise GW, BWE, BW[A:D] Set-up before CLK Rise 1.5 1.5 ns tWES 1.5 1.5 ns tDS Data Input Set-up before CLK Rise 1.5 1.5 ns tCES Chip Enable Set-Up before CLK Rise 1.5 1.5 ns tAH Address Hold after CLK Rise 0.5 0.5 ns tADH 0.5 0.5 ns 0.5 0.5 ns tWEH ADSP , ADSC Hold after CLK Rise ADV Hold after CLK Rise GW,BWE, BW[A:D] Hold after CLK Rise 0.5 0.5 ns tDH Data Input Hold after CLK Rise 0.5 0.5 ns tCEH Chip Enable Hold after CLK Rise 0.5 0.5 ns tADVS Max 133 MHz Description Min. Max Unit Hold Times tADVH Document #: 38-05393 Rev. *A Page 10 of 16 CY7C1329G Switching Waveforms Read Cycle Timing[17] t CYC CLK t CH t ADS t CL t ADH ADSP tADS tADH ADSC tAS tAH A1 ADDRESS A2 tWES A3 Burst continued with new base address tWEH GW, BWE, BW[A:D] tCES Deselect cycle tCEH CE tADVS tADVH ADV ADV suspends burst. OE t OEHZ t CLZ Data Out (Q) High-Z Q(A1) tOEV tCO t OELZ tDOH Q(A2) t CHZ Q(A2 + 1) Q(A2 + 2) Q(A2 + 3) Q(A2) Q(A2 + 1) t CO Burst wraps around to its initial state Single READ BURST READ DON’T CARE UNDEFINED Note: 17. On this diagram, when CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH, CE1 is HIGH or CE2 is LOW or CE3 is HIGH. Document #: 38-05393 Rev. *A Page 11 of 16 CY7C1329G Switching Waveforms (continued) Write Cycle Timing[17, 18] t CYC CLK tCH tADS tCL tADH ADSP tADS ADSC extends burst tADH tADS tADH ADSC tAS tAH A1 ADDRESS A2 A3 Byte write signals are ignored for first cycle when ADSP initiates burst tWES tWEH BWE, BW[A :D] tWES tWEH GW tCES tCEH CE t t ADVS ADVH ADV ADV suspends burst OE tDS Data In (D) High-Z t OEHZ tDH D(A1) D(A2) D(A2 + 1) D(A2 + 1) D(A2 + 2) D(A2 + 3) D(A3) D(A3 + 1) D(A3 + 2) Data Out (Q) BURST READ Single WRITE BURST WRITE DON’T CARE Extended BURST WRITE UNDEFINED Note: 18. Full width Write can be initiated by either GW LOW; or by GW HIGH, BWE LOW and BW[A : D] LOW. Document #: 38-05393 Rev. *A Page 12 of 16 CY7C1329G Switching Waveforms (continued) Read/Write Cycle Timing[17, 19, 20] tCYC CLK tCL tCH tADS tADH tAS tAH ADSP ADSC ADDRESS A1 A2 A3 A4 A5 A6 D(A5) D(A6) tWES tWEH BWE, BW[A:D] tCES tCEH CE ADV OE tDS tCO tDH tOELZ Data In (D) High-Z tCLZ Data Out (Q) High-Z Q(A1) Back-to-Back READs tOEHZ D(A3) Q(A2) Q(A4) Single WRITE Q(A4+1) Q(A4+2) BURST READ DON’T CARE Q(A4+3) Back-to-Back WRITEs UNDEFINED Notes: 19. The data bus (Q) remains in High-Z following a Write cycle unless an ADSP, ADSC, or ADV cycle is performed. 20. GW is HIGH. Document #: 38-05393 Rev. *A Page 13 of 16 CY7C1329G Switching Waveforms (continued) ZZ Mode Timing[21, 22] CLK t ZZ I t t ZZ ZZREC ZZI SUPPLY I t RZZI DDZZ ALL INPUTS (except ZZ) DESELECT or READ Only Outputs (Q) High-Z DON’T CARE Ordering Information Speed (MHz) Ordering Code Package Name Package Type 133 CY7C1329G-133AC A101 100-Lead Thin Quad Flat Pack 166 CY7C1329G-166AC A101 100-Lead Thin Quad Flat Pack Operating Range Commercial Notes: 21. Device must be deselected when entering ZZ mode. See Cycle Descriptions table for all possible signal conditions to deselect the device. 22. DQs are in High-Z when exiting ZZ sleep mode. Document #: 38-05393 Rev. *A Page 14 of 16 CY7C1329G Package Diagram 100-pin Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm) A101 51-85050-*A 2 i486 is a trademark, and Intel and Pentium are registered trademarks, of Intel Corporation. PowerPC is a registered trademark of IBM Corporation. All product and company names mentioned in this document may be trademarks of their respective holders. Document #: 38-05393 Rev. *A Page 15 of 16 © Cypress Semiconductor Corporation, 2004. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. CY7C1329G Document History Page Document Title: CY7C1329G 2-Mb (64K x 32) Pipelined Sync SRAM Document Number: 38-05393 Issue Date Orig. of Change REV. ECN NO. ** 200661 See ECN NJY New Data Sheet *A 213342 See ECN VBL Updated Ordering Info section: added -166AC Document #: 38-05393 Rev. *A Description of Change Page 16 of 16