TI TLK105

TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Industrial Temp, Single Port 10/100Mbs Ethernet Physical Layer Transceiver
Check for Samples: TLK105, TLK106
1 Introduction
1.1
Features
1
• Low Power Consumption: <205mW PHY and
275mW with Center Tap (Typical)
• Cable Diagnostics (TLK106)
• Programmable Fast Link Down Modes, <10µs
reaction time
• Fixed TX Clock to XI, with programmable phase
shift
• Programmable Power Back Off to reduce PHY
power up to 20% in systems with shorter
cables
• 3.3V MAC Interface
• Auto-MDIX for 10/100Mbs
• Energy Detection Mode
• MII and RMII Interfaces
• Serial Management Interface
• IEEE 802.3u MII
• IEEE 802.3u Auto-Negotiation and Parallel
Detection
• IEEE 802.3u ENDEC, 10Base-T
Transceivers and Filters
• IEEE 802.3u PCS, 100Base-TX Transceivers
1.3
• Error-Free Operation up to 150 Meters Under
Typical Conditions
• Integrated ANSI X3.263 Compliant TP-PMD
Physical Sublayer with Adaptive Equalization
and Baseline Wander Compensation
• Programmable LED Support: Link, Activity
• 10/100Mbs Packet BIST (Built in Self Test)
• Bus I/O Protection - ±16kV JEDEC HBM
• Enables implementation of IEEE1588 (V1 and
V2) Time Stamping at the MAC
• 32-pin QFN (5mm) × (5mm)
1.2
•
•
•
•
Applications
Industrial Networks and Factory Automation
Real Time Industrial Ethernet Applications
such as EtherCAT®, Ethernet/IP™, ProfiNET®,
SERCOSIII and VARAN
Motor and Motion Control
General Embedded Applications
Device Overview
The TLK10x is a single-port Ethernet PHY for 10Base-T and 100Base TX signaling, integrating all the
physical-layer functions needed to transmit and receive data on standard twisted-pair cables. The device
supports the standard Media Independent Interface (MII) and Reduced Media Independent Interface
(RMII) for direct connection to a Media Access Controller (MAC).
The device is designed for power-supply flexibility, and can operate with a single 3.3V power supply or
with combinations of 3.3V and 1.55V power supplies for reduced power operation.
The TLK10x uses mixed-signal processing to perform equalization, data recovery, and error correction to
achieve robust operation over CAT 5 twisted-pair wiring. The TLK10x not only meets the requirements of
IEEE 802.3, but maintains high margins in terms of cross-talk and alien noise.
TLK10x
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date. Products conform to
specifications per the terms of the Texas Instruments standard warranty. Production
processing does not necessarily include testing of all parameters.
Copyright © 2012–2013, Texas Instruments Incorporated
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
MII Option
RMII Option
MII/RMII Interface
Cable
Diagnostics
(TLK106 only)
Figure 1-1. TLK10x Functional Block Diagram
2
Introduction
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
1
.............................................. 1
............................................. 1
1.2
Applications .......................................... 1
1.3
Device Overview ..................................... 1
Pin Descriptions ......................................... 4
2.1
Pin Layout ........................................... 4
2.2
Serial Management Interface (SMI) ................. 5
2.3
MAC Data Interface .................................. 5
2.4
10Mbs and 100Mbs PMD Interface .................. 6
2.5
Clock Interface ....................................... 6
2.6
LED Interface ........................................ 6
2.7
Reset and Power Down ............................. 6
2.8
Power and Bias Connections ........................ 7
Hardware Configuration ............................... 7
3.1
Bootstrap Configuration .............................. 7
3.2
Power Supply Configuration ......................... 8
3.3
IO Pins Hi-Z State During Reset ..................... 9
3.4
Auto-Negotiation .................................... 10
3.5
Auto-MDIX .......................................... 10
3.6
MII Isolate Mode .................................... 11
3.7
PHY Address ....................................... 11
3.8
LED Interface ....................................... 12
3.9
Loopback Functionality ............................. 13
3.10 BIST ................................................ 15
3.11 Cable Diagnostics .................................. 15
Interfaces ................................................ 17
4.1
Media Independent Interface (MII) ................. 17
4.2
Reduced Media Independent Interface (RMII) ..... 18
4.3
Serial Management Interface ....................... 20
Architecture ............................................. 24
5.1
100Base-TX Transmit Path ......................... 24
5.2
100Base-TX Receive Path ......................... 27
5.3
10Base-T Receive Path ............................ 29
5.4
Auto Negotiation .................................... 30
5.5
Link Down Functionality ............................ 31
Reset and Power Down Operation ................. 33
Introduction
1.1
2
3
4
5
6
Features
7
8
....................................
.....................................
6.3
Power Down/Interrupt ..............................
6.4
Power Save Modes .................................
Design Guidelines .....................................
7.1
TPI Network Circuit .................................
7.2
Clock In (XI) Requirements .........................
7.3
Thermal Vias Recommendation ....................
Register Block .........................................
8.1
Register Definition ..................................
8.2
Extended Register Addressing .....................
8.3
PHY Status Register (PHYSTS) ...................
8.4
PHY Specific Control Register (PHYSCR) .........
8.5
MII Interrupt Status Register 1 (MISR1) ............
8.6
MII Interrupt Status Register 2 (MISR2) ............
8.7
False Carrier Sense Counter Register (FCSCR) ...
8.8
Receiver Error Counter Register (RECR) ..........
8.9
BIST Control Register (BISCR) ....................
8.10 RMII Control and Status Register (RCSR) .........
8.11 LED Control Register (LEDCR) ....................
8.12 PHY Control Register (PHYCR) ....................
8.13 10Base-T Status/Control Register (10BTSCR) ....
8.14 BIST Control and Status Register 1 (BICSR1) .....
8.15 BIST Control and Status Register2 (BICSR2) .....
8.16 Cable Diagnostic Control Register (CDCR) ........
8.17 PHY Reset Control Register (PHYRCR) ...........
8.18 TX_CLK Phase Shift Register (TXCPSR) ..........
8.19 Voltage Regulator Control Register (VRCR) .......
6.1
Hardware Reset
6.2
Software Reset
8.20
9
9.2
9.3
9.4
9.5
9.6
33
33
34
35
35
35
37
38
43
55
57
58
59
60
61
61
61
62
64
64
65
65
66
67
67
67
68
Cable Diagnostic Configuration/Result Registers
(TLK106) ............................................ 68
.............................
.................
RECOMMENDED OPERATING CONDITIONS ....
THERMAL CHARACTERISTICS ...................
Electrical Specifications
9.1
33
ABSOLUTE MAXIMUM RATINGS
74
74
74
74
DC CHARACTERISTICS
POWER SUPPLY CHARACTERISTICS
AC Specifications
Contents
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
3
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
2 Pin Descriptions
The TLK10x pins fall into the following interface categories (subsequent sections describe each interface):
•
•
•
•
Serial Management Interface
MAC Data Interface
Clock Interface
LED Interface
•
•
•
•
•
Reset and Power Down
Bootstrap Configuration Inputs
10/100Mbs PMD Interface
Special Connect Pins
Power and Ground pins
Note: Configuration pin option. See Section 3.1 for Jumper Definitions.
The definitions below define the functionality of each pin.
Input
Type: O
Output
Type: I/O
Input/Output
Type: OD
Open Drain
Type: PD, PU
Internal Pulldown/Pullup
Type: S
Configuration Pin (All configuration pins have weak internal pullups or pulldowns.
Use an external 2.2kΩ resistor if you need a different default value. See
Section 3.1 for details.)
CRS/CRS_DV / LED_CFG
RX_DV / MII_MODE
30
29
28
27
26
RX_CLK
RX_ER /AMDIX_EN
31
RXD_0 / PHYAD1
32
COL / PHYAD0
1
RXD_1 / PHYAD2
RXD_3 / PHYAD4
RXD_2 / PHYAD3
Pin Layout
25
24
PFBIN2
TX_CLK
2
23
XI
TX_EN
3
22
XO
TXD_0
4
21
VDD33_IO
TXD_1
5
20
MDC
TXD_2
6
19
MDIO
TXD_3
7
18
RESET
INT / PWDN
8
17
16
11
12 13
14
15
TD–
PFBIN1
AVDD33
PFBOUT
LED_LINK / AN_0
RBIAS
10
TD+
9
RD+
GND
RD–
2.1
Type: I
Figure 2-1. TLK10x PIN DIAGRAM, TOP VIEW
4
Pin Descriptions
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
This document describes signals that take on different names depending on configuration. In such cases,
the different names are placed together and separated by slash (/) characters. For example, "RXD_3 /
PHYAD4". Active low signals are represented by overbars.
2.2
Serial Management Interface (SMI)
PIN
NAME
NO.
TYPE
DESCRIPTION
MANAGEMENT DATA CLOCK: Clock signal for the management data input/output (MDIO) interface. The
maximum MDC rate is 25MHz; there is no minimum MDC rate. MDC is not required to be synchronous to the
TX_CLK or the RX_CLK.
MDC
20
I
MDIO
19
I/O
2.3
MANAGEMENT DATA I/O: Bidirectional command / data signal synchronized to MDC. Either the local
controller or the TLK10x may drive the MDIO signal. This pin requires a pull-up resistor with value 2.2kΩ.
MAC Data Interface
PIN
NAME
TX_CLK
NO.
2
TYPE
DESCRIPTION
O, PD
MII TRANSMIT CLOCK: MII Transmit Clock provides the 25MHz or 2.5MHz reference clock
depending on the speed. Note that in MII mode, this clock has constant phase referenced to
REF_CLK. Applications requiring such constant phase may use this feature.
Unused in RMII mode. In RMII, X1 reference clock is used as the clock for both transmit and
receive.
TX_EN
3
I, PD
TRANSMIT ENABLE: TX_EN is presented on the rising edge of the TX_CLK . TX_EN
indicates the presence of valid data inputs on TXD[3:0] in MII mode, and on TXD [1:0] in the
RMII mode. TX_EN is an active high signal.
TXD_0
TXD_1
TXD_2
TXD_3
4
5
6
7
I, PD
TRANSMIT DATA: In MII mode, the transmit data nibble received from the MAC is
synchronous to the rising edge of the TX_CLK signal. In RMII mode, TXD [1:0] received from
the MAC is synchronous to the 50MHz reference clock on XI.
RX_CLK
25
O
RECEIVE CLOCK: In MII mode it is the receive clock that provides either a 25MHz or 2.5MHz
reference clock, depending on the speed, that is derived from the received data stream.
RX_DV / MII_MODE
26
S, O, PD
RECEIVE DATA VALID: This pin indicates valid data is present on the RXD [3:0] for MII mode
or on RXD [1:0] for RMII mode, independently from Carrier Sense.
28
RECEIVE ERROR: This pin indicates that an error symbol has been detected within a received
packet in both MII and RMII mode. In MII mode, RX_ER is asserted high synchronously to
S, O, PU
RX_CLK and in RMII mode, synchronously to XI (50MHz). This pin is not required to be used
by the MAC, in either MII or RMII, because the PHY is corrupting data on a receive error.
RX_ER / AMDIX_EN
RXD_0 / PHYAD1
RXD_1 / PHYAD2
RXD_2 / PHYAD3
RXD_3 / PHYAD4
30
31
32
1
RECEIVE DATA: Symbols received on the cable are decoded and presented on these pins
synchronous to RX_CLK. They contain valid data when RX_DV is asserted. A nibble RXD [3:0]
is received in the MII mode and 2-bits RXD[1:0] is received in the RMII Mode.
S, O, PD
PHY address pins PHYAD[4:1] are multiplexed with RXD [3:0], and are pulled down. PHYAD0
(LSB of the address) is multiplexed with COL on pin 29, and is pulled up.
If no external pullup/pulldown is present, the default address is 0x01.
CARRIER SENSE: In MII mode this pin is asserted high when the receive medium is non-idle.
CRS / CRS_DV/
LED_CFG
27
S, O, PU
COL / PHYAD0
29
COLLISION DETECT: For MII mode in Full Duplex Mode this pin is always low. In 10BaseS, O, PU T/100Base-TX half-duplex modes, this pin is asserted HIGH only when both transmit and
receive media are non-idle. This pin is not used in RMII mode.
CARRIER SENSE/RECEIVE DATA VALID: In RMII mode, this pin combines the RMII Carrier
and Receive Data Valid indications.
Pin Descriptions
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
5
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
2.4
www.ti.com
10Mbs and 100Mbs PMD Interface
PIN
NAME
TYPE
NO.
DESCRIPTION
Differential common driver transmit output (PMD Output Pair): These differential outputs are
automatically configured to either 10Base-T or 100Base-TX signaling.
TD–, TD+
11, 12
I/O
In Auto-MDIX mode of operation, this pair can be used as the Receive Input pair. These pins require 3.3V
bias for operation.
Differential receive input (PMD Input Pair): These differential inputs are automatically configured to
accept either 100Base-TX or 10Base-T signaling.
RD–, RD+
9, 10
I/O
In Auto-MDIX mode of operation, this pair can be used as the Transmit Output pair. These pins require
3.3V bias for operation.
2.5
Clock Interface
PIN
NAME
NO.
TYPE
DESCRIPTION
CRYSTAL/OSCILLATOR INPUT:
XI
23
MII reference clock: Reference clock. 25MHz ±50ppm-tolerance crystal reference or oscillator input. The
device supports either an external crystal resonator connected across pins XI and XO, or an external
CMOS-level oscillator source connected to pin XI only.
I
RMII reference clock: Primary clock reference input for the RMII mode. The input must be connected to a
50MHz ±50ppm-tolerance CMOS-level oscillator source.
XO
22
2.6
CRYSTAL OUTPUT: Reference Clock output. XO pin is used for crystal only. This pin should be left floating
when an oscillator input is connected to XI.
O
LED Interface
(See Table 3-3 for LED Mode Selection)
PIN
NAME
NO.
TYPE
DESCRIPTION
LED Pin to indicate status
LED_LINK /
AN_0
2.7
17
Mode 1
LINK Indication LED: Indicates the status of the link. When the link is good, the LED
is ON.
Mode 2
ACT indication LED: Indicates transmit and receive activity in addition to the status
of the Link. The LED is ON when Link is good. The LED blinks when the transmitter
or receiver is active.
S, O, PU
Reset and Power Down
PIN
NAME
NO.
RESET
18
TYPE
I, PU
DESCRIPTION
This pin is an active-low reset input that initializes or re-initializes all the internal registers of the
TLK10x. Asserting this pin low for at least 1 µs will force a reset process to occur. All jumper
options are reinitialized as well.
Register access is required for this pin to be configured either as power down or as an interrupt.
The default function of this pin is power down.
INT / PWDN
8
When this pin is configured for a power down function, an active low signal on this pin places the
IO, OD, PU device in power down mode.
When this pin is configured as an interrupt pin, then this pin is asserted low when an interrupt
condition occurs. The pin has an open-drain output with a weak internal pull-up. Some
applications may require an external pull-up resistor.
6
Pin Descriptions
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
2.8
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Power and Bias Connections
PIN
NAME
NO.
TYPE
DESCRIPTION
RBIAS
16
I
Bias Resistor Connection: Use a 4.87kΩ 1% resistor connected from RBIAS to GND.
PFBOUT
15
O
Power Feedback Output: Place 10µf and 0.1μF capacitors (ceramic preferred) close to PFBOUT.
In single-supply operation, connect this pin to PFBIN1 and PFBIN2 (pin 13 and pin 24). See Figure 3-1
for proper placement.
In multiple supply operation, this pin is not used.
PFBIN1
13
PFBIN2
24
VDD33_IO
AVDD33
GND
Power Feedback Input: These pins are fed with power from PFBOUT (pin 15) in single supply
operation.
I
In multiple supply operation, connect a 1.55V external power supply to these pins. Connect a small
capacitor of 0.1µF close to each pin. To power down the internal linear regulator, write to register
0x00d0.
21
P
I/O 3.3V Supply
14
P
Analog 3.3V power supply
Ground
Pad
P
Ground Pad
3 Hardware Configuration
This section includes information on the various configuration options available with the TLK10x. The
configuration options described below include:
•
•
•
•
•
•
3.1
Bootstrap Configuration
Power Supply Configuration
IO Pins Hi-Z State During Reset
Auto-Negotiation
Auto-MDIX
MII Isolate mode
•
•
•
•
•
PHY Address
LED Interface
Loopback Functionality
BIST
Cable Diagnostics (TLK106 only)
Bootstrap Configuration
Bootstrap configuration is a convenient way to configure the TLK10x into specific modes of operation.
Some of the functional pins are used as configuration inputs. The logic states of these pins are sampled
during reset and are used to configure the device into specific modes of operation. The table below
describes bootstrap configuration.
A 2.2kΩ resistor is used for pull-down or pull-up to change the default configuration. If the default option is
desired, then there is no need for external pull-up or pull down resistors. Because these pins may have
alternate functions after reset is deasserted, they must not be connected directly to VCC or GND.
PIN
NAME
PHYAD0
PHYAD1
PHYAD2
PHYAD3
PHYAD4
TYPE
NO.
DESCRIPTION
(COL)
(RXD_0)
(RXD_1)
(RXD_2)
(RXD_3)
29
30
31
32
1
PHY Address [4:0]: The TLK10x provides five PHY address pins, the states of which are
latched into an internal register at system hardware reset. The TLK10x supports PHY
S, O, PD /
Address values 0 (<00000>) through 31 (<11111>). PHYAD[4:1] pins have weak internal
PU
pull-down resistors, and PHYAD[0] has weak internal pull-up resistor, setting the default
PHYAD if no external resistors are connected.
AN_0 (LED_LINK)
17
S, O, PU
AN_0: FD-HD config. FD = pull up.
The default wake-up is auto negotiation enable 100BT.
LED_CFG (CRS)
27
S, O, PU
This option selects the operation mode of the LED LINK pin. Default is Mode 1. All modes
are also configurable via register access. See PHY Control Register (PHYCR), Address
0x0019.
Hardware Configuration
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
7
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
PIN
www.ti.com
TYPE
NAME
NO.
DESCRIPTION
AMDIX_EN (RX_ER)
28
S, O, PU
This option sets the Auto-MDIX mode. By default, it enables Auto-MDIX. An external pulldown resistor disables Auto-MDIX mode.
MII_MODE (RX_DV)
26
S, O, PD
MII Mode Select: This option selects the operating mode of the MAC data interface. This
pin has a weak internal pull-down, and it defaults to normal MII operation mode. An
external pull-up causes the device to operate in RMII mode.
3.2
Power Supply Configuration
The TLK10x provides best-in-class flexibility of power supplies.
3.2.1
Single Supply Operation
If a single 3.3V power supply is desired, the TLK10x internal regulator provides the necessary core supply
voltages. Ceramic capacitors of 10µf and 0.1µf should be placed close to the PFBOUT (pin 15) which is
the output of the internal regulator. The PFBOUT pin should be connected to the PFBIN1 and PFBIN2 on
the board. A small capacitor of 0.1µF should be placed close to the PFBIN1 (pin 13) and PFBIN2 (pin 24).
To operate in this mode the TLK10x supply pins should be connected as shown in Figure 3-1.
3.3V
Supply
10mF
3.3V
Supply
10nF
1nF
100pF
Pin 14
(AVDD33)
Pin 9
(RD–)
3.3V
Supply
49.9W
1:1
1mF
0.1mF
RD –
49.9W
0.1μF
Pin 13
(PFBIN1)
Pin 15
(PFBOUT)
10μF
Pin 24
(PFBIN2)
Pin 10
(RD+)
RD +
1mF
Pin 11
(TD–)
0.1mF*
0.1μF
TD –
3.3V
Supply
49.9W
TD +
1mF
0.1μF
0.1mF* 1:1
0.1mF*
1m F
T1
RJ45
49.9W
Pin 12
(TD+)
Pin 21
(VDD33_IO)
3.3V
Supply
100pF 1nF
10nF
10mF
Figure 3-1. Power Connections for Single Supply Operation
8
Hardware Configuration
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
3.2.2
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Dual Supply Operation
When a 1.55V external power rail is available, the TLK10x can be configured as shown in Figure 3-2.
PFBOUT (pin 15) is left floating. The 1.55V external supply is connected to PFBIN1 (pin 13) and PFBIN2
(pin 24). Furthermore, to lower the power consumption, the internal regulator should be powered down by
writing ‘1’ to bit 15 of the VRCR register (0x00d0h).
3.3V
Supply
10mF
3.3V
Supply
10nF
1nF
100pF
Pin 14
(AVDD33)
Pin 9
(RD–)
3.3V
Supply
49.9 W
1:1
0.1mF
1mF
RD–
49.9 W
Pin 15
(PFBOUT)
Pin 10
(RD+)
1.55V
Supply
10mF
10nF
1nF
100pF
Pin 13
(PFBIN1)
RD+
1mF
Pin 11
(TD–)
0.1mF*
Floating
TD–
3.3V
Supply
49.9 W
TD+
1m F
0.1mF
1mF
1.55V
Supply
10mF
0.1mF* 1:1
T1
RJ45
49.9 W
10nF
1nF
Pin 12
(TD+)
Pin 24
100pF (PFBIN2)
3.3V
Supply
Pin 21
(VDD33_IO)
100pF 1nF
10nF
10mF
Figure 3-2. Power Connections for Dual Supply Operation
When operating with dual supplies, follow these guidelines:
• When powering up, ramp up the 3.3V supply before the 1.55V supply.
• When powering down, turn off the 1.55V supply before turning off the 3.3V supply.
• Use the external RESET pin after power up to reset the PHY.
• To use the internal power-on reset, PFBIN1 and PBIN2 must be operational less than 100ms after
3.3V rises to detect the internal RESET.
3.3
IO Pins Hi-Z State During Reset
The following IO or output pins are in hi-Z state when RESET is active (Low).
Type
Internal
PU/PD
TXD_3
IO
PD
TX_EN
IO
INT/PWDN
IO
LED_LINK
IO
MDIO
IO
RX_DV
IO
CRS
IO
RX_ER
IO
Pin Name
Type
Internal
PU/PD
COL
IO
PU
PD
RXD_0
IO
PD
PU
RXD_1
IO
PD
PU
RXD_2
IO
PD
RXD_3
IO
PD
PD
TX_CLK
O
PU
CLK25MHz_OUT
O
PU
RX_CLK
O
Pin Name
Hardware Configuration
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
9
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
3.4
www.ti.com
Auto-Negotiation
The TLK10x device auto-negotiates to operate in 10Base-T or 100Base-TX. With Auto-Negotiation
enabled, the TLK10x negotiates with the link partner to determine the speed and duplex mode. If the link
partner cannot Auto-Negotiate, the TLK10x device enters parallel-detect mode to determine the speed of
the link partner. Parallel-detect mode uses fixed half-duplex mode.
The TLK10x supports four different Ethernet protocols (10Mbs Half-Duplex, 10Mbs Full-Duplex, 100Mbs
Half-Duplex, and 100Mbs Full-Duplex). Auto-Negotiation selects the highest performance protocol based
on the advertised ability of the Link Partner. Control the Auto-Negotiation function within the TLK10x by
internal register access according to the IEEE specification.
Alternatively, control the HD-FD functionality by configuring the AN_0 pins. The state of AN_0 selects full
or half duplex mode, both in Auto-negotiation or force 100/10 mode as given in Table 3-1. The state of
AN_0 upon power-up/reset, determines the state of bits [8:5] of the ANAR register (0x04h).
Auto-Negotiation advertises ANEN, 100BT by default. Full-Duplex or Half-Duplex configuration is available
through the AN_0 bit. Internal register access configures the device for a specific mode.
Table 3-1. Auto-Negotiation Modes
AN_0
Forced Mode
0
10Base-T, Half-Duplex
100Base-TX, Half-Duplex
1
10Base-T, Half or Full-Duplex
100Base-TX, Half or Full-Duplex
Internal register access controls the Auto-Negotiation function, as defined by the IEEE 802.3u
specification. For further detail regarding Auto-Negotiation, see Clause 28 of the IEEE 802.3u
specification.
3.5
Auto-MDIX
The TLK10x device automatically determines whether or not it needs to cross over between pairs,
eliminating the requirement for an external crossover cable. If the TLK10x interoperates with a device that
implements MDI/MDIX crossover, a random algorithm as described in IEEE 802.3 determines which
device performs the crossover.
Auto-MDIX is enabled by default and can be configured via pin strap, control register CR1 (0x09h), bit 14
or via register PHYCR (0x19h), bit 15.
The crossover can be manually forced through bit 14 of the PHYCR (0x19h) register. Neither AutoNegotiation nor Auto-MDIX is required to be enabled in forcing crossover of the MDI pairs.
Auto-MDIX can be used in the forced 100Base-TX mode. Because in modern networks all the nodes are
100Base-TX, having the Auto-MDIX working in the forced 100Base-TX mode resolves the link faster
without the need for the long Auto-Negotiation period.
10
Hardware Configuration
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
3.6
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
MII Isolate Mode
The TLK10x can be put into MII-Isolate mode by writing bit 10 of the BMCR register.
When in the MII-Isolate mode, the TLK10x ignores packet data present at the TXD[3:0], TX_EN inputs,
and presents a high impedance on the TX_CLK, RX_CLK, RX_DV, RX_ER, RXD[3:0], COL, and CRS
outputs. When in isolate mode, the TLK10x continues to respond to all management transactions.
When in isolate mode, the PMD output pair does not transmit packet data, but continues to source
100Base-TX scrambled idles or 10Base-T normal link pulses. The TLK10x can auto-negotiate or parallel
detect on the receive signal at the PMD input pair. A valid link can be established for the receiver even
when the TLK10x is in Isolate mode.
3.7
PHY Address
The 5 PHY address inputs pins are shared with the RXD[3:0] pins and COL pin as shown in Table 3-2.
Table 3-2. PHY Address Mapping
PIN Number
PHYAD FUNCTION
RXD FUNCTION
29
PHYAD0
COL
30
PHYAD1
RXD_0
31
PHYAD2
RXD_1
32
PHYAD3
RXD_2
1
PHYAD4
RXD_3
Each TLK10x or port sharing an MDIO bus in a system must have a unique physical address. With 5
address input pins, the TLK10x can support PHY Address values 0 (<00000>) through 31 (<11111>). The
address-pin states are latched into an internal register at device power-up and hardware reset. Because
all the PHYAD[4:0] pins have weak internal pull-down/up resistors, the default setting for the PHY address
is 00001 (0x01h).
PHYAD4 = 0
PHYAD3 = 0
PHYAD2 = 0
COL
RXD_0
RXD_1
RXD_3
RXD_2
See Figure 3-3 for an example of a PHYAD connection to external components. In this example, the
PHYAD configuration results in address 00011 (0x03h).
PHYAD1 = 1
PHYAD0 = 1
2.2 kW
VCC
Figure 3-3. Illustrative PHYAD Configuration Example
Hardware Configuration
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
11
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
3.8
www.ti.com
LED Interface
The TLK10x supports one configurable Light Emitting Diode (LED) pin. The device supports 2 LED
configurations: Link and Activity. Functions are multiplexed into two modes. The LED can be controlled by
configuration pin and internal register bits. Bit 5 of the PHY Control register (PHYCR) selects the LED
mode as described in Table 3-3.
Table 3-3. LED Mode Select
Mode
LED_CFG[0]
(bit 5) or (pin 27)
1
1
ON for Good Link
OFF for No Link
2
0
ON for Good Link
BLINK for Activity
LED_LINK
The LED_LINK pin in Mode 1 indicates the link status of the port. The LED is OFF when no link is present.
In Mode 2 it is ON to indicate that the link is good; BLINK indicates that activity is present on either
transmit or receive channel. Bits 10:9 of the LEDCR register (0x18) control the blink rate. The default blink
rate is 5Hz.
LED_LINK
See Figure 3-4 for an example of AN_0 connections to external components. In this example, the AN_0
configuration results in Full-Duplex advertised.
AN_O = 1
2.2kW
470W
VCC
Figure 3-4. AN Pin Configuration and LED Loading Example
12
Hardware Configuration
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
3.9
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Loopback Functionality
The TLK10x provides several options for Loopback that test and verify various functional blocks within the
PHY. Enabling loopback mode allows in-circuit testing of the TLK10x digital and analog data path.
Generally, the TLK10x may be configured to one of the Near-end loopback modes or to the Far-end
(reverse) loopback.
3.9.1
Near-End Loopback
Near-end loopback provides the ability to loop the transmitted data back to the receiver via the digital or
analog circuitry. The point at which the signal is looped back is selected using loopback control bits with
several options being provided. Figure 3-5 shows the PHY near-end loopback functionality.
PCS Loopback
Analog Loopback
M
MAC/
Switch
I
I
Signal
Process
PCS
PHY
AFE
XFMR
RJ45
1
4
5
6
7
8
PHY Digital
MII Loopback
2
3
Digital Loopback
External Loopback
Figure 3-5. Block Diagram, Near-End Loopback Mode
The Near-end Loopback mode is selected by setting the respective bit in the BIST Control Register
(BISCR), MII register address 0x0016. MII loopback can be selected by using the BMCR register at
address 0x0000, bit [14].
The Near-end Loopback can be selected according to the following:
• Reg 0x0000, Bit [14]: MII Loopback
• Reg 0x0016, Bit [0]: PCS input Loopback
• Reg 0x0016, Bit [1]: PCS output Loopback
• Reg 0x0016, Bit [2]: Digital Loopback
• Reg 0x0016, Bit [3]: Analog Loopback
Table 3-4 describes the available operational modes for each loop mode:
Table 3-4. Loop Modes
Loop Mode
MII
PCS Input
PCS Output
Digital
Analog (1)
External
Operational Setting
Force/ANEG 100/10
Force 100/10
Force 100
Force 100
Force 10/100 ANEG
10
Force/ANEG 100/10
Operational MAC int.
MII Only
MII or RMII
MII or RMII
MII or RMII
MII or RMII
MII or RMII
(1)
Requires 100Ω termination
While in MII Loopback mode, there is no link indication, but packets propagate back to the MAC. While in
MII Loopback mode the data is looped back, and can also be transmitted onto the media. For transmitting
data during MII loopback in 100BT only please use bit [6] in the BISCR Register address 0x0016. To
ensure proper operation in Analog Loopback mode, 100Ω terminations should be attached to the RJ45
connector. External Loopback can be performed while working in normal mode (Bits 3:0 of the BISCR
register are asserted to 0, and on the RJ45 connector, pin 1 is connected to pin 3 and pin 2 is connected
to pin 6). To maintain the desired operating mode, Auto-Negotiation should be disabled before selecting
Loopback mode. This constraint is not relevant for external-loopback mode. For selected loopback Delay
propagation timing please see Section 9.6.21.
Hardware Configuration
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
13
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
3.9.2
www.ti.com
Far-End Loopback
Far-end (Reverse) loopback is a special test mode to allow testing the PHY from the link-partner side. In
this mode, data that is received from the link partner passes through the PHY's receiver, looped back on
the MII and transmitted back to the link partner. Figure 3-6 shows Far-end loopback functionality.
MAC/
Switch
M
I
I
PCS
Signal
Process
XFMR
CAT5 Cable
&
Link Partner
RJ45
PHY
AFE
PHY Digital
Reverse Loopback
Figure 3-6. Block Diagram, Far-End Loopback Mode
The Reverse Loopback mode is selected by setting bit 4 in the BIST Control Register (BISCR), MII
register address 0x0016.
While in Reverse Loopback mode the data is looped back and also transmitted onto the MAC Interface
and all data signals that come from the MAC are ignored.
Table 3-5 describes the operating modes for Far-End Loopback.
Table 3-5. Far-End Loopback Modes
14
Operational MAC Int.
MII Mode
RMII Mode
Operational Setting
Force/ANEG 10/100
Force/ANEG 10
Hardware Configuration
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
3.10 BIST
The device incorporates an internal PRBS Built-in Self Test (BIST) circuit to accommodate in-circuit
testing or diagnostics. The BIST circuit can be used to test the integrity of the transmit and receive data
paths. The BIST can be performed using both internal loopback (digital or analog) or external loop back
using a cable fixture. The BIST simulates pseudo-random data transfer scenarios in format of real packets
and Inter-Packet Gap (IPG) on the lines. The BIST allows full control of the packet lengths and of the IPG.
The BIST is implemented with independent transmit and receive paths, with the transmit block generating
a continuous stream of a pseudo-random sequence. The device generates a 15-bit pseudo-random
sequence for the BIST. The received data is compared to the generated pseudo-random data by the BIST
Linear Feedback Shift Register (LFSR) to determine the BIST pass/fail status. The number of error bytes
that the PRBS checker received is stored in the BICSR1 register (0x001Bh). The status of whether the
PRBS checker is locked to the incoming receive bit stream, whether the PRBS has lost sync, and whether
the packet generator is busy, can be read from the BISCR register (0x0016h). While the lock and sync
indications are required to identify the beginning of proper data reception, for any link failures or data
corruption, the best indication is the contents of the the error counter in the BICSR1 register (0x001Bh).
The PRBS test can be put in a continuous mode or single mode by using bit 14 of the BISCR register
(0x0016h). In continuous mode, when one of the PRBS counters reaches the maximum value, the counter
starts counting from zero again. In single mode, when the PRBS counter reaches its maximum value, the
PRBS checker stops counting.
The device allows the user to control the length of the PRBS packet. By programming the BICSR2 register
(0x001Ch) one can set the length of the PRBS packet. There is also an option to generate a single-packet
transmission of two types, 64 and 1518 bytes, through register bit 13 of the BISCR register (0x0016h).
The single generated packet is composed of a constant data.
3.11 Cable Diagnostics
With the vast deployment of Ethernet devices, the need for reliable, comprehensive and user-friendly
cable diagnostic tool is more important than ever. The wide variety of cables, topologies, and connectors
deployed results in the need to non-intrusively identify and report cable faults. The TI cable-diagnostic unit
provides extensive information about cable integrity.
The TLK106 offers the following capabilities in its Cable Diagnostic tools kit:
1. Time Domain Reflectometry (TDR)
2. Active Link Cable Diagnostic (ALCD)
3.11.1 TDR
The TLK106 uses Time Domain Reflectometry (TDR) to determine the quality of the cables, connectors,
and terminations in addition to estimating the cable length. Some of the possible problems that can be
diagnosed include opens, shorts, cable impedance mismatch, bad connectors, termination mismatches,
cross faults, cross shorts and any other discontinuities along the cable.
The TLK106 transmits a test pulse of known amplitude (1V or 2.5V) down each of the two pairs of an
attached cable. The transmitted signal continues down the cable and reflects from each cable
imperfection, fault, bad connector, and from the end of the cable itself. After the pulse transmission the
TLK106 measures the return time and amplitude of all these reflected pulses. This technique enables
measuring the distance and magnitude (impedance) of non-terminated cables (open or short),
discontinuities (bad connectors), and improperly-terminated cables with ±1m accuracy.
The TLK106 also uses data averaging to reduce noise and improve accuracy. The TLK106 can record up
to five reflections within the tested pair. If more than 5 reflections are recorded, the TLK106 saves the first
5 of them. If a cross fault is detected, the TDR saves the first location of the cross fault and up to 4
reflections in the tested channel. The TLK106 TDR can measure cables up to 200m in length.
Hardware Configuration
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
15
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
For all TDR measurements, the transformation between time of arrival and physical distance is done by
the external host using minor computations (such as multiplication, addition and lookup tables). The host
must know the expected propagation delay of the cable, which depends, among other things, on the cable
category (for example, CAT5, CAT5e, or CAT6).
TDR measurement is allowed in the TLK106 in the following scenarios:
• While Link partner is disconnected – cable is unplugged at the other side
• Link partner is connected but remains “quiet” (for example, in power down mode)
• TDR could be automatically activated when the link fails or is dropped by setting bit 8 of register
0x0009 (CR1). The results of the TDR run after the link fails will be saved in the TDR registers. The
SW could read these registers at any time to apply post processing on the TDR results. This mode is
designed for cases in which the link dropped due to cable disconnections, in which after link failure, the
line will be quiet to allow a proper function of the TDR.
3.11.2 ALCD
The TLK106 also supports Active Link Cable Diagnostic (ALCD). The ALCD offers a passive method to
estimate the cable length during active link. The ALCD uses passive digital signal processing based on
adapted data, thus enabling measurement of cable length with an active link partner.
The ALCD Cable length measurement accuracy is ±5m for the pair used in the Rx path (due to the
passive nature of the test, only the receive path is measured).
16
Hardware Configuration
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
4 Interfaces
4.1
Media Independent Interface (MII)
The Media Independent Interface (MII) is a synchronous 4-bit wide nibble data interface that connects the
PHY to the MAC in 100B-TX and 10B-T modes. The MII is fully compliant with IEEE802.3-2002 clause 22.
The MII signals are summarized below.
Data signals
TXD [3:0]
RXD [3:0]
Transmit and receive-valid signals
TX_EN
RX_DV
Line-status signals
CRS (carrier sense)
COL (collision)
Figure 4-1 shows the MII-mode signals.
PHY
MAC
TX_CLK
TX_CLK
TX_EN
TX_EN
TXD [3:0]
TXD [3:0]
RX_CLK
RX_CLK
RX_DV
RX_DV
RX_ER
RX_ER
RXD [3:0]
RXD [3:0]
CRS
CRS
COL
COL
Figure 4-1. MII Signaling
The isolate register 0.10 defined in IEEE802.3-2002 used to electrically isolate the PHY from the MII (if
set, all transactions on the MII interface are ignored by the PHY).
Additionally, the MII interface includes the carrier sense signal CRS, as well as a collision detect signal
COL. The CRS signal asserts to indicate the reception of data from the network or as a function of
transmit data in Half Duplex mode. The COL signal asserts as an indication of a collision which can occur
during half-duplex operation when both transmit and receive operation occur simultaneously.
Interfaces
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
17
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
4.2
www.ti.com
Reduced Media Independent Interface (RMII)
TLK10x incorporates the Reduced Media Independent Interface (RMII) as specified in the RMII
specification (rev1.2) from the RMII consortium. The purpose of this interface is to provide a low cost
alternative to the IEEE 802.3u MII as specified in Clause 22. Architecturally, the RMII specification
provides an additional reconciliation layer on either side of the MII, but can be implemented in the absence
of an MII.
The RMII specification has the following characteristics:
• Supports 10Mbs and 100Mbs data rates
• Single clock reference sourced from the MAC to PHY (or from an external source)
• Provides independent 2 bit wide (di-bit) transmit and receive data paths
• Uses CMOS signal levels, the same levels as the MII interface
In this mode, data transfers two bits at a time using the 50MHz RMII reference clock for both transmit and
receive. RMII mode uses the following pins:
Signal
Pin
XI (RMII reference clock is 50MHz)
23
TXD_0
4
TXD_1
5
TX_EN
3
CRS_DV
27
RX_ER
28
RXD_0
30
RXD_1
31
Data on TXD [1:0] are latched at the PHY with reference to the reference-clock edges on the XI pin. Data
on RXD [1:0] are latched at the MAC with reference to the same reference clock edges on the XI pin. The
RMII operates at the same speed (50MHz) in both 10B-T and 100B-TX. In 10B-T the data is 10 times
slower than the reference clock, so transmit data is sampled every 10 clocks. Likewise, receive data is
generated on every 10th clock so that an attached MAC device can sample the data every 10 clocks.
In addition, RMII mode supplies an RX_DV signal which allows a simpler method of recovering receive
data without the need to separate RX_DV from the CRS_DV indication. RMII mode requires a 50MHz
oscillator to be connected to the device XI pin.
The TLK10x supports a special mode called “RMII receive clock” mode. This mode, which is not part of
the RMII specification, allows synchronization of the MAC-PHY RX interface. In this mode, the PHY
generates a recovered 50MHz clock through the RX_CLK pin and synchronizes the RXD[1:0], CRS_DV,
RX_DV and RX_ER signals to this clock. Setting register 0x000A bit [0] is required to activate this mode.
Figure 4-2 describes the RMII signals connectivity between the TLK10x and any MAC device.
18
Interfaces
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
PHY
TX_EN
TXD[1:0]
RX_CLK
RX_DV
RX_ER
RXD[1:0]
CRS/RX_DV
MAC
TX_EN
TXD[1:0]
RX_CLK (optional)
RX_DV (optional)
RX_ER
RXD[1:0]
CRS/RX_DV
XI
50MHz
Clock Source
Figure 4-2. TLK10x RMII/MAC Connection
RMII function includes a programmable elastic buffer to adjust for the frequency differences between the
reference clock and the recovered receive clock. The programmable elastic buffer minimizes internal
propagation delay based on expected maximum packet size and clock accuracy.
Table 4-1 indicates how to program the buffer FIFO based on the expected max packet size and clock
accuracy. It assumes that the RMII reference clock and the far-end transmitter clock have the same
accuracy.
Table 4-1. Recommended RMII Packet Sizes
Start Threshold RBR[1:0]
Latency Tolerance
Recommended packet size at
±50ppm
Recommended packet size at
±100ppm
1(4-bits)
2 bits
2400 bytes
1200 bytes
2(8-bits)
6 bits
7200 bytes
3600 bytes
3(12-bits)
10 bits
12000 bytes
6000 bytes
0(16-bits)
14 bits
16800 bytes
8400 bytes
Interfaces
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
19
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
4.3
www.ti.com
Serial Management Interface
The Serial Management Interface (SMI), provides access to the TLK10x internal registers space for status
information and configuration. The SMI is compatible with IEEE802.3-2002 clause 22. The implemented
register set consists of all the registers required by the IEEE802.3-2002 in addition to several others,
providing additional visibility and controllability of the TLK10x device.
The SMI includes the MDC management clock input and the management MDIO data pin. The MDC clock
is sourced by the external management entity, also called Station (STA), and can run at maximum clock
rate of 25MHz. MDC is not expected to be continuous, and can be turned off by the external management
entity when the bus is idle.
The MDIO is sourced by the external management entity and by the PHY. The data on the MDIO pin is
latched on the rising edge of the MDC clock. The MDIO pin requires a pull-up resistor (2.2kΩ) which,
during IDLE and turnaround, pulls MDIO high.
Up to 32 PHYs can share a common SMI bus. To distinguish between the PHYs, a 5-bit address is used.
During power-up reset, the TLK10x latches the PHYAD[4:0] configuration pins (Pin 29 to Pin 32) to
determine its address.
The management entity must not start an SMI transaction in the first cycle after power-up reset. To
maintain valid operation, the SMI bus should remain inactive at least one MDC cycle after hard reset is
de-asserted.
In normal MDIO transactions, the register address is taken directly from the management-frame reg_addr
field, thus allowing direct access to 32 16-bit registers (including those defined in IEEE802.3 and vendor
specific). The data field is used for both reading and writing. The Start code is indicated by a <01> pattern.
This pattern makes sure that the MDIO line transitions from the default idle line state. Turnaround is
defined as an idle bit time inserted between the Register Address field and the Data field. To avoid
contention during a read transaction, no device may actively drive the MDIO signal during the first bit of
Turnaround. The addressed TLK10x drives the MDIO with a zero for the second bit of turnaround and
follows this with the required data. Figure 4-3 shows the timing relationship between MDC and the MDIO
as driven/received by the Station (STA) and the TLK10x (PHY) for a typical register read access.
20
Interfaces
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
For write transactions, the station-management entity writes data to the addressed TLK10x, thus
eliminating the requirement for MDIO Turnaround. The Turnaround time is filled by the management entity
by inserting <10>. Figure 4-4 shows the timing relationship for a typical MII register write access. The
frame structure and general read/write transactions are shown in Table 4-2, Figure 4-3, and Figure 4-4.
Table 4-2. Typical MDIO Frame Format
MII Management Serial Protocol
<idle><start><op code><device addr><reg addr><turnaround><data><idle>
Read Operation
<idle><01><10><AAAAA><RRRRR><Z0><xxxx xxxx xxxx xxxx><idle>
Write Operation
<idle><01><01><AAAAA><RRRRR><10><xxxx xxxx xxxx xxxx><idle>
MDC
Z
MDIO Z
(STA)
Z
MDIO
(PHY)
0
Z
Idle
1
Start
1
0
0
Opcode
(Read)
1
1
0
0
0
PHY Address
(PHYAD = 0Ch)
0
0
0
Z
0 Z 0
Register Address
(00h = BMCR)
0
0
1
1
0
0
0
1
0
0
0
0
0
0
0
0
Register Data
TA
Z
Idle
Figure 4-3. Typical MDC/MDIO Read Operation
MDC
MDIO
(STA)
Z
Z
Idle
Z
0
1
Start
0
1
Opcode
(Read)
0
1
1
0
PHY Address
(PHYAD = 0Ch)
0
0
0
0
0
0
Register Address
(00h = BMCR)
1
0
0
0
0
0
TA
0
0
0
0
0
0
0
0
0
0
0
0
Register Data
Z
Idle
Figure 4-4. Typical MDC/MDIO Write Operation
Interfaces
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
21
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
4.3.1
www.ti.com
Extended Address Space Access
The TLK10x SMI function supports read/write access to the extended register set using registers
REGCR(0x000Dh) and ADDAR(0x000Eh) and the MDIO Manageable Device (MMD) indirect method
defined in IEEE802.3ah Draft for clause 22 for accessing the clause 45 extended register set.
Accessing the standard register set, MDIO registers 0 to 31, can be performed using the normal direct
MDIO access or the indirect method, except for register REGCR(0x000Dh) and ADDAR(0x000Eh) which
can be accessed only using the normal MDIO transaction. The SMI function will ignore indirect accesses
to these registers.
REGCR(0x000Dh) is the MDIO Manageable MMD access control. In general, register REGCR(4:0) is the
device address DEVAD that directs any accesses of ADDAR(0x000Eh) register to the appropriate MMD.
Specifically, the TLK10x uses the vendor specific DEVAD[4:0] = "11111" for accesses. All accesses
through registers REGCR and ADDAR should use this DEVAD. Transactions with other DEVAD are
ignored. REGCR[15:14] holds the access function: address (00), data with no post increment (01), data
with post increment on read and writes (10) and data with post increment on writes only (11).
• ADDAR is the address/data MMD register. ADDAR is used in conjunction with REGCR to provide the
access to the extended register set. If register REGCR[15:1] is 00, then ADDAR holds the address of
the extended address space register. Otherwise, ADDAR holds the data as indicated by the contents
of its address register. When REGCR[15:14] is set to 00, accesses to register ADDAR modify the
extended register set address register. This address register should always be initialized in order to
access any of the register within the extended register set.
• When REGCR[15:14] is set to 01, accesses to register ADDAR access the register within the extended
register set selected by the value in the address register.
• When REGCR[15:14] is set to 10, access to register ADDAR access the register within the extended
register set selected by the value in the address register. After that access is complete, for both reads
and writes, the value in the address register is incremented.
• When REGCR[15:14] is set to 11, access to register ADDAR access the register within the extended
register set selected by the value in the address register. After that access is complete, for write
accesses only, the value in the address register is incremented. For read accesses, the value of the
address register remains unchanged.
The following sections describe how to perform operations on the extended register set using register
REGCR and ADDAR.
4.3.1.1
Write Address Operation
To set the address register:
1. Write the value 0x001F (address function field = 00, DEVAD = 31) to register REGCR.
2. Write the desired register address to register ADDAR.
Subsequent writes to register ADDAR (step 2) continue to write the address register.
4.3.1.2
Read Address Operation
To read the address register:
1. Write the value 0x001F (address function field = 00, DEVAD = 31) to register REGCR.
2. Read the register address from register ADDAR.
Subsequent reads to register ADDAR (step 2) continue to read the address register.
22
Interfaces
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
4.3.1.3
To
1.
2.
3.
4.
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Write (no post increment) Operation
write an extended register set register:
Write the value 0x001F (address function field = 00, DEVAD = 31) to register REGCR.
Write the desired register address to register ADDAR.
Write the value 0x401F (data, no post increment function field = 01, DEVAD = 31) to register REGCR.
Write the content of the desired extended register set register to register ADDAR.
Subsequent writes to register ADDAR (step 4) continue to rewrite the register selected by the value in the
address register.
Note: steps (1) and (2) can be skipped if the address register was previously configured.
4.3.1.4
To
1.
2.
3.
4.
Read (no post increment) Operation
read an extended register set register:
Write the value 0x001F (address function field = 00, DEVAD = 31) to register REGCR.
Write the desired register address to register ADDAR.
Write the value 0x401F (data, no post increment function field = 01, DEVAD = 31) to register REGCR.
Read the content of the desired extended register set register to register ADDAR.
Subsequent reads from register ADDAR (step 4) continue reading the register selected by the value in the
address register.
Note: steps (1) and (2) can be skipped if the address register was previously configured.
4.3.1.5
Write (post increment) Operation
1. Write the value 0x001F (address function field = 00, DEVAD = 31) to register REGCR.
2. Write the register address from register ADDAR.
3. Write the value 0x801F (data, post increment on reads and writes function field = 10, DEVAD = 31) or
the value 0xC01F (data, post increment on writes function field = 11. DEVAD = 31) to register REGCR.
4. Write the content of the desired extended register set register to register ADDAR.
Subsequent writes to register ADDAR (step 4) write the next higher addressed data register selected by
the value of the address register; the address register is incremented after each access.
4.3.1.6
Read (post increment) Operation
To read an extended register set register and automatically increment the address register to the next
higher value following the write operation:
1. Write the value 0x001F (address function field = 00, DEVAD = 31) to register REGCR.
2. Write the desired register address to register ADDAR.
3. Write the value 0x801F (data, post increment on reads and writes function field = 10, DEVAD = 31) to
register REGCR.
4. Read the content of the desired extended register set register to register ADDAR.
Subsequent reads to register ADDAR (step 4) read the next higher addressed data register selected by
the value of the address register; the address register is incremented after each access.
Interfaces
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
23
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
5 Architecture
The TLK10x Fast Ethernet transceiver is a physical layer core for Ethernet 100Base-TX and 10Base-T
applications. The TLK10x contains all the active circuitry required to implement the physical layer functions
to transmit and receive data on standard CAT 3 and 5 unshielded twisted pair. The core supports the
IEEE 802.3 Standard Fast Media Independent Interface (MII), as well as the Reduced Media Independent
Interface (RMII), for direct connection to a MAC/Switch port.
The TLK10x uses mixed signal processing to perform equalization, data recovery and error correction to
achieve robust and low power operation over the existing CAT 5 twisted pair wiring. The TLK10x
architecture not only meets the requirements of IEEE802.3, but maintains a high level of margin over the
IEEE requirements for NEXT, Alien and External noise.
4B/5B
encoding
Scrambler
NRZ to NRZI
Convertor
MLT-3
encoding
D/A
Convertor
100Base TX
Line Driver
10Base T
Filter
10Base T
Line Driver
Transmit
Manchester
encoding
Adv.
Link Monitor
MII
Receive
10Base T
Receive
Filter
Manchester
decoding
4B/5B
decoding
DeScrambler
NRZI to NRZ
Convertor
100Base TX
10Base-T
MLT-3
decoding
DSP (BLW
Correction,
Adapt. Equal)
ADC (Filter,
Amplifierl)
Figure 5-1. PHY Architecture
5.1
100Base-TX Transmit Path
In 100Base-TX, the MAC feeds the 100Mbps transmit data in 4-bit wide nibbles through the MII interface.
The data is encoded into 5-bit code groups, encapsulated with control code symbols and serialized. The
control-code symbols indicate the start and end of the frame and code other information such as transmit
errors. When no data is available from the MAC, IDLE symbols are constantly transmitted. The serialized
bit stream is fed into a scrambler. The scrambled data stream passes through an NRZI encoder and then
through an MLT3 encoder. Finally, it is fed to the DAC and transmitted through one of the twisted pairs of
the cable.
5.1.1
MII Transmit Error Code Forwarding
According to IEEE 802.3:
“If TX_EN is de-asserted on an odd nibble boundary, PHY should extend TX_EN by one TX_CLK
cycle and behave as if TX_ER were asserted during that cycle”.
The TLK10x supports Error Forwarding in MII transmission from the MAC to the PHY. Error forwarding
allows adding information to the frame to be used as an error code between the 2 MACs. The error code
informs the receiving MAC on the link partner side of the reason for the error from the transmitting side. If
the MAC transmits an odd number of nibbles, an additional error nibble is added to the transmitted frame
just before the end of the transmission.
To turn off Transmit Error Forwarding, write to bit 1 of register CR2 (0x000A). If Error Forwarding is
disabled, delivered packets contain either odd or even numbers of nibbles.
In Figure 5-2, Error Code Forwarding functionality is illustrated. The wave diagram demonstrates MAC’s
transmitted signals in one side and MAC’s reception signals on link partner side.
24
Architecture
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
TX_CLK
TX_EN
TXD[3:0]
Data n-2
[3:0]
Data n-2
[7:4]
Data n-1
[3:0]
Data n-1
[7:4]
Data n
[3:0]
Data n
[7:4]
Error
Code
RX_CLK
RX_DV
RXD[3:0]
Data n-2
[3:0]
Data n-2
[7:4]
Data n-1
[3:0]
Data n-1
[7:4]
Data n
[3:0]
Data n
[7:4]
Error
Code
Don't Care
RX_ER
Figure 5-2. Transmit Code Error Forwarding Diagram
5.1.2
4-Bit to 5-Bit Encoding
The transmit data that is received from the MAC first passes through the 4-Bit to 5-Bit encoder. This block
encodes 4-bit nibble into 5-bit code-groups according to the Table 5-1. Each 4-bit data nibble is mapped to
16 of the 32 possible code-groups. The remaining 16 code-groups are either used for control information
or they are considered as not valid.
The code-group encoder substitutes the first 8-bits of the MAC preamble with a J/K code-group pair
(11000 10001) upon transmission. The code-group encoder continues to replace subsequent 4-bit
preamble and data nibbles with corresponding 5-bit code-groups. At the end of the transmit packet, upon
the de-assertion of Transmit Enable signal from the MAC, the code-group encoder adds the T/R codegroup pair (01101 00111) indicating the end of the frame.
After the T/R code-group pair, the code-group encoder continuously adds IDLEs into the transmit data
stream until the next transmit packet is detected.
Architecture
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
25
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
Table 5-1. 4-Bit to 5-Bit Code Table
4-Bit Code
Symbol
5-Bit Code
0000
0
11110
Receiver Interpretation
0001
1
01001
0010
2
10100
0011
3
10101
0100
4
01010
0101
5
01011
0110
6
01110
0111
7
01111
1000
8
10010
1001
9
10011
1010
A
10110
1011
B
10111
1100
C
11010
1101
D
11011
1110
E
11100
1111
F
11101
DESCRIPTION
Symbol (1)
5-Bit Code
Inter-Packet IDLE
I
11111
IDLE
First nibble of SSD
J
11000
First nibble of SSD, translated to "0101" following /I/ (IDLE),
else RX_ER asserted high
Second nibble of SSD
K
10001
Second nibble of SSD, translated to "0101" following /J/, else
RX_ER asserted high
First nibble of ESD
T
01101
First nibble of ESD, causes de-assertion of CRS if followed
by /R/, else assertion of RX_ER
Second nibble of ESD
R
00111
Second nibble of ESD, causes de-assertion of CRS if
following /T/, else assertion of RX_ER
Transmit Error Symbol
H
00100
RX_ER
Invalid Symbol
V
00000
V
00001
INVALID
RX_ER asserted high If during RX_DV
V
00010
V
00011
V
00101
V
00110
V
01000
V
01100
Data
IDLE AND CONTROL CODES
(1)
Control code-groups I, J, K, T and R in data fields will be mapped as invalid codes, together with RX_ER asserted.
5.1.3
Scrambler
The purpose of the scrambler is to flatten the power spectrum of the transmitted signal, thus reduce EMI.
The scrambler seed is generated with reference to the PHY address so that multiple PHYs that reside
within the system will not use the same scrambler sequence.
5.1.4
NRZI and MLT-3 Encoding
To comply with the TP-PMD standard for 100Base-TX transmission over CAT-5 unshielded twisted pair
cable, the scrambled data must be NRZI encoded. The serial binary data stream output from the NRZI
encoder is further encoded to MLT-3. MLT-3 is a tri-level code where a change in the logic level
represents a code bit '1' and the logic output remaining at the same level represents a code bit '0'.
26
Architecture
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
5.1.5
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Digital to Analog Converter
The multipurpose programmable transmit Digital to Analog Converter (DAC) receives digital coded
symbols and generates filtered analog symbols to be transmitted on the line. In 100B-TX the DAC applies
a low-pass shaping filter to minimize EMI. The DAC is designed to improve the return loss requirements
and enable the use of low-cost transformers.
Digital pulse-shape filtering is also applied in order to conform to the pulse masks defined by standard and
to reduce EMI and high frequency signal harmonics.
5.2
100Base-TX Receive Path
In 100B-TX, the ADC sampled data is passed to an adaptive equalizer. The adaptive equalizer drives the
received symbols to the MLT3 decoder. The decoded NRZ symbols are transferred to the descrambler
block for descrambling and deserialization.
5.2.1
Analog Front End
The Receiver Analog Front End (AFE) resides in front of the 100B-TX receiver. The AFE consists of an
Analog to Digital Converter (ADC), receive filters and a Programmable Gain Amplifier (PGA).
The ADC samples the input signal at the 125MHz clock recovered by the timing loop and feeds the data
into the adaptive equalizer. The ADC is designed to optimize the SNR performance at the receiver input
while maintaining high power-supply rejection ratio and low power consumption. There is only one ADC in
the TLK10x, which receives the analog input data from the relevant cable pair, according to MDI-MDIX
resolution.
The PGA, digitally controlled by the adaptive equalizer, fully uses the dynamic range of the ADC by
adjusting the incoming-signal amplitude. Generally, the PGA attenuates short-cable strong signals and
amplifies long-cable weak signals.
5.2.2
Adaptive Equalizer
The adaptive equalizer removes Inter-Symbol Interference (ISI) from the received signal introduced by the
channel and analog Tx/Rx filters. The TLK10x includes both Feed Forward Equalization (FFE) and
Decision Feedback Equalization (DFE). The combination of both adaptive modules with the adaptive gain
control results in a powerful equalizer that can eliminate ISI and compensate for cable attenuation for
longer-reach cables. In addition, the Equalizer includes a Shift Gear Step mechanism to provide fast
convergence on the one hand and small residual-adaptive noise in steady state on the other hand.
5.2.3
Baseline Wander Correction
The DC offset of the transmitted signal is shifted down or up based on the polarity of the transmitted data
because the MLT-3 data is coupled onto the CAT 5 cable through a transformer that is high-pass in
nature. This phenomenon is called Baseline wander. To prevent corruption of the received data because
of this phenomenon, the receiver corrects the baseline wander and can receive the ANSI TP-PMD-defined
"killer packet" with no bit errors.
5.2.4
NRZI and MLT-3 Decoding
The TLK10x decodes the MLT-3 information from the Digital Adaptive Equalizer block to binary NRZI data.
The NRZI-to-NRZ decoder is used to present NRZ-formatted data to the descrambler.
Architecture
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
27
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
5.2.5
www.ti.com
Descrambler
The descrambler is used to descramble the received NRZ data. The data is further deserialized and the
parallelized data is aligned to 5-bit code-groups and mapped into 4-bit nibbles. At initialization, the 100BTX descrambler uses the IDLE-symbols sequence to lock on the far-end scrambler state. During that time,
neither data transmission nor reception is enabled. After the far-end scrambler state is recovered, the
descrambler constantly monitors the data and checks whether it still synchronized. If, for any reason,
synchronization is lost, the descrambler tries to re-acquire synchronization using the IDLE symbols.
5.2.6
5B/4B Decoder and Nibble Alignment
The code-group decoder functions as a look up table that translates incoming 5-bit code-groups into 4-bit
nibbles. The code-group decoder first detects the Start of Stream Delimiter (SSD) /J/K/ code-group pair
preceded by IDLE code-groups at the start of a packet. Once the code group alignment is determined, it is
stored and used until the next start-of-frame. The decoder replaces the /J/K/ with the MAC preamble.
Specifically, the /J/K/ 10-bit code-group pair is replaced by the nibble pair (0101 0101). All subsequent 5bit code-groups are converted to the corresponding 4-bit nibbles for the duration of the entire packet. This
conversion ceases upon the detection of the /T/R/ code-group pair denoting the End-of-Stream Delimiter
(ESD) or with the reception of a minimum of two IDLE code-groups.
5.2.7
Timing Loop and Clock Recovery
The receiver must lock on the far-end transmitter clock in order to sample the data at the optimum timing.
The timing loop recovers the far-end clock frequency and offset from the received data samples and
tracks instantaneous phase drifts caused by timing jitter.
The TLK10x has a robust adaptive-timing loop (Tloop) mechanism that is responsible for tracking the FarEnd TX clock and adjusting the AFE sampling point to the incoming signal. The Tloop implements an
advanced tracking mechanism that when combined with different available phases, always keeps track of
the optimized sampling point for the data, and thus offers a robust RX path,tolerant to both PPM and
Jitter. The TLK10x is capable of dealing with PPM and jitter at levels far higher than those defined by the
standard.
5.2.8
Phase-Locked Loops (PLL)
In 10B-T the digital phase lock loop (DPLL) function recovers the far-end link-partner clock from the
received Manchester signal. The DPLL is able to combat clock jitter of up to ±18ns and frequency drifts of
±500ppm between the local PHY clock and the far-end clock. The DPLL feeds the decoder with a
decoded serial bit stream.
The integrated analog Phase-Locked Loop (PLL) provides the clocks to the analog and digital sections of
the PHY. The PLL is driven by an external reference clock (sourced at the XI,XO pins with a crystal
oscillator, or at XI with an external reference clock).
5.2.9
Link Monitor
The TLK10x implements the link monitor State Machine (SM) as defined by the IEEE 802.3 100Base-TX
Standard. In addition, the TLK10x enables several add-ons to the link monitor SM activated by
configuration bits. The new add-ons include the recovery state which enables the PHY to attempt recovery
in the event of a temporary energy-loss situation before entering the LINK_FAIL state, thus restarting the
whole link establishment procedure. This sequence allows significant reduction of the recovery time in
scenarios where the link loss is temporal.
In addition, the link monitor SM enables moving to the LINK_DOWN state based on descrambler
synchronization failure and not only on Signal_Status indication, which shortens the drop-link down time.
These add-ons are supplementary to the IEEE standard and are bypassed by default.
28
Architecture
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
5.2.10 Signal Detect
The signal detect function of the TLK10x is incorporated to meet the specifications mandated by the
ANSIFDDI TP-PMD Standard as well as the IEEE 802.3 100Base-TX Standard for both voltage thresholds
and timing parameters.
The energy-detector module provides signal-strength indication in various scenarios. Because it is based
on an IIR filter, this robust energy detector has excellent reaction time and reliability. The filter output is
compared to predefined thresholds in order to decide the presence or absence of an incoming signal.
The energy detector also implements hysteresis to avoid jittering in signal-detect indication. In addition it
has fully-programmable thresholds and listening-time periods, enabling shortening of the reaction time if
required.
5.2.11 Bad SSD Detection
A Bad Start of Stream Delimiter (Bad SSD) is any transition from consecutive idle code-groups to non-idle
code-groups which is not prefixed by the code-group pair /J/K. If this condition is detected, the TLK10x
asserts RX_ER, and presents RXD[3:0] = 1110 to the MII for the cycles that correspond to received 5B
code-groups until at least two IDLE code groups are detected. In addition, the FCSCR register (0x14h) is
incremented by one for every error in the nibble.
When at least two IDLE code groups are detected, RX_ER and CRS are de-asserted.
5.3
10Base-T Receive Path
In 10B-T, after the far-end clock is recovered, the received Manchester symbols pass to the Manchester
decoder. The serial decoded bit stream is aligned to the start of the frame, de-serialized to 4-bit wide
nibbles and sent to the MAC through the MII.
5.3.1
10M Receive Input and Squelch
The squelch feature determines when valid data is present on the differential receive inputs. The TLK10x
implements a squelch to prevent impulse noise on the receive inputs from being mistaken for a valid
signal. Squelch operation is independent of the 10Base-T operating mode. The squelch circuitry employs
a combination of amplitude and timing measurements (as specified in the IEEE 802.3 10Base-T standard)
to determine the validity of data on the twisted-pair inputs.
The signal at the start of a packet is checked by the squelch, and any pulses not exceeding the squelch
level (either positive or negative, depending upon polarity) are rejected. When this first squelch level is
exceeded correctly, the opposite squelch level must then be exceeded no earlier than 50ns. Finally, the
signal must again exceed the original squelch level no earlier than 50ns to qualify as a valid input
waveform, and not be rejected. This checking procedure results in the typical loss of three preamble bits
at the beginning of each packet. When the transmitter is operating, five consecutive transitions are
checked before indicating that valid data is present. At this time, the squelch circuitry is reset.
5.3.2
Collision Detection
When in Half-Duplex mode, a 10Base-T collision is detected when receive and transmit channels are
active simultaneously. Collisions are reported by the COL signal on the MII.
The COL signal remains set for the duration of the collision. If the PHY is receiving when a collision is
detected, it is reported immediately (through the COL pin).
5.3.3
Carrier Sense
Carrier Sense (CRS) may be asserted due to receive activity after valid data is detected via the squelch
function. For 10Mb/s Half Duplex operation, CRS is asserted during either packet transmission or
reception. For 10Mb/s Full Duplex operation, CRS is asserted only during receive activity.
CRS is de-asserted following an end-of-packet.
Architecture
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
29
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
5.3.4
www.ti.com
Jabber Function
Jabber is a condition in which a station transmits for a period of time longer than the maximum permissible
packet length, usually due to a fault condition. The jabber function monitors the TLK10x output and
disables the transmitter if it attempts to transmit a packet of longer than legal size. A jabber timer monitors
the transmitter and disables the transmission if the transmitter is active for approximately 100ms.
When disabled by the Jabber function, the transmitter stays disabled for the entire time that the ENDEC
module's internal transmit enable is asserted. This signal must be de-asserted for approximately 500ms
(the unjab time) before the Jabber function re-enables the transmit outputs.
The Jabber function is only available and active in 10Base-T mode.
5.3.5
Automatic Link Polarity Detection and Correction
Swapping the wires within the twisted pair causes polarity errors. Wrong polarity affects the 10B-T PHYs.
The 100B-TX is immune to polarity problems because it uses MLT3 encoding. The 10B-T automatically
detects reversed polarity according to the received link pulses or data.
5.3.6
10Base-T Transmit and Receive Filtering
External 10Base-T filters are not required when using the TLK10x, because the required signal
conditioning is integrated into the device. Only isolation transformers and impedance matching resistors
are required for the 10Base-T transmit and receive interface. The internal transmit filtering ensures that all
the harmonics in the transmit signal are attenuated by at least 30dB.
5.3.7
10Base-T Operational Modes
The TLK10x has two basic 10Base-T operational modes:
• Half Duplex mode – In Half Duplex mode the TLK10x functions as a standard IEEE 802.3 10Base-T
transceiver supporting the CSMA/CD protocol.
• Full Duplex mode – In Full Duplex mode the TLK10x is capable of simultaneously transmitting and
receiving without asserting the collision signal. The TLK10x 10Mbs ENDEC is designed to encode and
decode simultaneously.
5.4
Auto Negotiation
The auto-negotiation function, described in detail in IEEE802.3 chapter 28, provides the means to
exchange information between two devices and automatically configure both of them to take maximum
advantage of their abilities.
5.4.1
Operation
Auto negotiation uses the 10B-T link pulses to encapsulate the transmitted data in a sequence of pulses,
also referred to as a Fast Link Pulses (FLP) burst. The FLP Burst consists of a series of closely spaced
10B-T link integrity test pulses that form an alternating clock/data sequence. Extraction of the data bits
from the FLP Burst yields a Link Code Word that identifies the operational modes supported by the remote
device, as well as some information used for the auto negotiation function’s handshake mechanism.
The information exchanged between the devices during the auto-negotiation process consists of the
devices' abilities such as duplex support and speed. This information allows higher levels of the network
(MAC) to send to the other link partner vendor-specific data (via the Next Page mechanism, see below),
and provides the mechanism for both parties to agree on the highest performance mode of operation.
30
Architecture
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
When auto negotiation has started, the TLK10x transmits FLP on one twisted pair and listens on the other,
thus trying to find out whether the other link partner supports the auto negotiation function as well. The
decision on what pair to transmit/listen depends on the MDI/MDI-X state. If the other link partner activates
auto negotiation, then the two parties begin to exchange their information. If the other link partner is a
legacy PHY or does not activate the auto negotiation, then the TLK10x uses the parallel detection
function, as described in IEEE802.3 chapters 40 and 28, to determine 10B-T or 100B-TX operation
modes.
5.4.2
Initialization and Restart
The TLK10x initiates the auto negotiation function if one of the following events have happened:
1. Hardware reset de-assertion
2. Software reset (via register)
3. Auto negotiation restart (via register BMCR (0x0000h) bit 9)
4. Power-up sequence (via register BMCR (0x0000h) bit 11)
The auto-negotiation function is also initiated when the auto-negotiation enable bit is set in register BMCR
(0x0000h) bit 12 and one of the following events has happened:
1. Software restart
2. Transitioning to link_fail state, as described in IEEE802.3
To disable the auto-negotiation function during operation, clear register BMCR (0x0000h) bit 12. During
operation, setting/resetting this register does not affect the TLK10x operation. For the changes to take
place, issue a restart command through register BMCR (0x0000h) bit 9.
5.4.3
Next Page Support
The TLK10x supports the optional feature of the transmission and reception of auto-negotiation additional
(vendor specific) next pages.
If next pages are needed, the user must set register ANAR(0x0004h) bit 15 to '1'. The next pages are then
sent and received through registers ANNPTR(0x0007h) and ANLNPTR(0x0008h), respectively. The user
must poll register ANER(0x0006h) bit 1 to check whether a new page has been received, and then read
register ANLNPTR for the received next page's content. Only after register ANLNPTR is read may the
user write to register ANNPTR the next page to be transmitted. After register ANNPTR is written, new next
pages overwrite the contents of register ANLNPTR.
If register ANAR(0x0004h) bit 15 is set, then the next page sequence is controlled by the user, meaning
that the auto-negotiation function always waits for register ANNPTR to be written before transmitting the
next page.
If additional user-defined next pages are transmitted and the link partner has more next pages to send, it
is the user's responsibility to keep writing null pages (of value 0x2001) to register ANNPTR until the link
partner notifies that it has sent its last page (by setting bit 15 of its transmitted next page to zero).
5.5
Link Down Functionality
The TLK10x includes advanced link-down capabilities that support various real-time applications. The linkdown mechanism of the TLK10x is configurable and includes enhanced modes that allow extremely fast
reaction times to link-drops.
Architecture
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
31
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
First Link Failure
Occurrence
Valid Data
LOW Quality Data / Link Loss
Signal
Link Drop
T1
Link Loss
Indication
(Link LED)
Figure 5-3. TLK10x Link Loss Mechanism
As described in Figure 5-3, the TLK10x link loss mechanism is based on a time window search period, in
which the signal behavior is monitored. The T1 window is set by default to reduce typical link-drops to less
than 1ms.
The TLK10x supports enhanced modes that shorten the window called Fast Link Down mode. In this
mode, which can be configured in Control Register 3 (CR3), address 0x000B, bits 3:0, the T1 window is
shortened significantly, in most cases less than 10µs. In this period of time there are several criteria
allowed to generate link loss event and drop the link:
1. Count RX Error in the MII interface: When a predefined number of 32 RX Error occurrences in time
window of 10µs is reached the link will drop.
2. Count MLT3 Errors at the signal processing output (100BT uses MLT3 coding, and when a violation of
this coding is detected, an MLT3 error is declared). When a predefined number of 20 errors
occurrences in 10µs is reached the link will drop.
3. Count Low Signal Quality Threshold crossing (When the signal quality is under a certain threshold that
allows proper link conditions). When a predefined number of 20 occurrences in 10µs is reached, the
link will drop.
4. Signal/Energy loss indications. When Energy detector indicates Energy Loss, the link will be dropped.
Typical reaction time is 10µs.
The Fast Link Down functionality allows the use of each of these options separately or in any combination.
Note that since this mode enables extremely quick reaction time, it is more exposed to temporary bad linkquality scenarios.
32
Architecture
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
6 Reset and Power Down Operation
The TLK10x includes an internal power-on-reset (POR) function, and therefore does not need an explicit
reset for normal operation after power up.
At power-up, if required by the system, the RESET pin (active low) should be de-asserted 200µs after the
power is ramped up to allow the internal circuits to settle and for the internal regulators to stabilize. If
required during normal operation, the device can be reset by a hardware or software reset.
6.1
Hardware Reset
A hardware reset is accomplished by applying a low pulse (TTL level), with a duration of at least 1μs, to
RESET. This pulse resets the device such that all registers are reinitialized to default values, and the
hardware configuration values are re-latched into the device (similar to the power-up/reset operation). The
time from the point when the reset pin is de-asserted to the point when the reset has concluded internally
is approximately 200µs.
6.2
Software Reset
An IEEE registers software reset is accomplished by setting the reset bit (bit 15) of the BMCR register
(0x0000h). This bit only resets the IEEE-defined standard registers in the address space 0x00h to 0x07h.
A global software reset is accomplished by setting bit 15 of register PHYRCR (0x001F) to ‘1’. This bit
resets all the internal circuits in the PHY including IEEE-defined registers (0x00h to 0x07h) and all the
extended registers. The global software reset resets the device such that all registers are reset to default
values and the hardware configuration values are maintained.
A global software restart is accomplished by setting bit 14 of register PHYRCR (0x001F) to ‘1’. This
action resets all the PHY circuits except the registers in the Register File.
The time from the point when the resets/restart bits are set to the point when the software resets/restart
has concluded is approximately 200µs. TI recommends that the software driver code must wait 500µs
following software reset before allowing further serial MII operations with the TLK10x.
6.3
Power Down/Interrupt
The Power Down and Interrupt functions are multiplexed on pin 8 of the device. By default, this pin
functions as a power down input and the interrupt function is disabled. This pin can be configured as an
interrupt output pin by setting bit 0 (INT_OE) to ‘1’ in the PHYSCR (0x0011h) register. The PHYSCR
register is also used to enable and set the polarity of the interrupt.
6.3.1
Power Down Control Mode
The INT/PWDN pin can be asserted low to put the device in a Power Down mode. An external control
signal can be used to drive the pin low, overcoming the weak internal pull-up resistor. Alternatively, the
device can be configured to initialize into a Power Down state by use of an external pulldown resistor on
the INT/PWDN pin.
6.3.2
Interrupt Mechanisms
The interrupt function is controlled via register access. All interrupt sources are disabled by default. The
MISR1 (0x0012) and MISR2 (0x0013) registers provide independent interrupt enable bits for the various
interrupts supported by the TLK10x. The INT/PWDN pin is asynchronously asserted low when an interrupt
condition occurs. The source of the interrupt can be determined by reading the interrupt status registers
MISR1 (0x0012h) and MISR2 (0x0013). One or more bits in the MISR registers will be set, indicating all
currently-pending interrupts. Reading the MISR registers clears ALL pending interrupts.
Reset and Power Down Operation
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
33
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
6.4
www.ti.com
Power Save Modes
The TLK10x supports three types of power-save modes. The lowest power consumption is achieved in
IEEE power down mode. To enter IEEE power down mode, pull the INT/PWDN pin to LOW or program bit
11 in the Basic Mode Control Register (BMCR), address 0x0000. In this mode all internal circuitry except
SMI functionality is shut down (Register access is still available).
To enable and activate all other power save modes through register access, use register PHYSCR
(0x0011h). Setting bit 14 enables all power-save modes; bits [13:12] select between them.
Setting bits [13:12] to “01” powers down the PHY, forcing it into IEEE power down mode (Similar to BMCR
bit 11 functionality).
Setting bits [13:12] to “10” puts the PHY in Low Power Active WOL (Wake-On-LAN) mode.
Setting bits [13:12] to “11” puts the PHY in Low Power Passive WOL (Wake-On-LAN) mode.
When these bits are cleared, the PHY powers up and returns to the last state it was in before it was
powered down.
34
Reset and Power Down Operation
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
7 Design Guidelines
7.1
TPI Network Circuit
Figure 7-1 shows the recommended circuit for a 10/100Mbs twisted pair interface. Below is a partial
list of recommended transformers. Variations with PCB and component characteristics require that
the application be tested to verify that the circuit meets the requirements of the intended application.
•
•
Pulse H1102
Pulse HX1188
Vdd
Common-mode chokes
may be required.
RD–
49.9 W
Vdd
1:1
0.1 mF
49.9 W
RD–
RD+
1mF
0.1 mF*
RD+
TD–
TD–
49.9 W
Vdd
TD+
1mF
49.9 W
0.1 mF
0.1mF*
1:1
T1
RJ45
Note: Center tap is connected to Vdd
TD+
* Place capacitors close to the
transformer center taps
Place resistors and capacitors close to the device.
All values are typical and are ±1%
Figure 7-1. 10/100Mbs Twisted Pair Interface
7.2
Clock In (XI) Requirements
The TLK10x supports an external CMOS-level oscillator source or an internal oscillator with an external
crystal.
7.2.1
Oscillator
If an external clock source is used, XI should be tied to the clock source and XO should be left floating.
The amplitude of the oscillator should be a nominal voltage of 3.3V.
Design Guidelines
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
35
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
7.2.2
www.ti.com
Crystal
The use of a 25MHz, parallel, 20pF-load crystal is recommended if a crystal source is desired. Figure 7-2
shows a typical connection for a crystal resonator circuit. The load capacitor values will vary with the
crystal vendors; check with the vendor for the recommended loads.
The oscillator circuit is designed to drive a parallel-resonance AT-cut crystal with a minimum drive level of
100μW and a maximum of 500μW. If a crystal is specified for a lower drive level, a current limiting resistor
must be placed in series between XO and the crystal.
As a starting point for evaluating an oscillator circuit, if the requirements for the crystal are not known, set
the values for CL1 and CL2 at 33pF, and R1 should be set at 0Ω. Specifications for a 25MHz crystal are
listed in Table 7-3.
XI
XO
R1
CL1
CL2
S0340-01
Figure 7-2. Crystal Oscillator Circuit
Table 7-1. 25MHz Oscillator Specification
PARAMETER
TEST CONDITIONS
MIN
Frequency
TYP
MAX
25
UNIT
MHz
Frequency Tolerance
Operational Temperature
±50
Frequency Stability
1 year aging
±50
ppm
Rise / Fall Time
10%–90%
8
nsec
Jitter (Short term)
Cycle-to-cycle
Jitter (Long term)
Accumulative over 10 ms
Symmetry
Duty Cycle
50
psec
1
40%
Load Capacitance
ppm
nsec
60%
15
30
TYP
MAX
pF
Table 7-2. 50MHz Oscillator Specification
PARAMETER
TEST CONDITIONS
MIN
Frequency
50
UNIT
MHz
Frequency Tolerance
Operational Temperature
±50
Frequency Stability
1 year aging
±50
ppm
Rise / Fall Time
10%–90%
6
nsec
Jitter (Short term)
Cycle-to-cycle
Jitter (Long term)
Accumulative over 10 ms
Symmetry
Duty Cycle
50
psec
1
40%
ppm
nsec
60%
Table 7-3. 25MHz Crystal Specification
PARAMETER
TEST CONDITIONS
MIN
Frequency
Frequency Tolerance
Frequency Stability
MAX
25
UNIT
MHz
Operational Temperature
±50
ppm
At 25°C
±50
ppm
±5
ppm
40
pF
1 year aging
Load Capacitance
36
TYP
10
Design Guidelines
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
7.3
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Thermal Vias Recommendation
The following thermal via guidelines apply to DOWN_PAD, pin 33:
1. Thermal via size = 0.2mm
2. Recommend 4 vias
3. Vias have a center to center separation of 2mm.
Adherence to this guideline is required to achieve the intended operating temperature range of the device.
Figure 7-3 illustrates an example layout.
Figure 7-3. Example Layout
Design Guidelines
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
37
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
8 Register Block
Table 8-1. Register Map
OFFSET HEX
ACCESS
TAG
DESCRIPTION
00h
RW
BMCR
Basic Mode Control Register
01h
RO
BMSR
Basic Mode Status Register
02h
RO
PHYIDR1
PHY Identifier Register 1
03h
RO
PHYIDR2
PHY Identifier Register 2
04h
RW
ANAR
05h
RO
ANLPAR
06h
RO
ANER
07h
RW
ANNPTR
Auto-Negotiation Next Page TX
08h
RO
ANLNPTR
Auto-Negotiation Link Partner Ability Next Page Register
09h
RW
CR1
Control Register 1
0Ah
RW
CR2
Control Register 2
0Bh
RW
CR3
Control Register 3
0Ch
RW
RESERVED
0Dh
RW
REGCR
Register control register
0Eh
RW
ADDAR
Address or Data register
0Fh
RW
RESERVED
Auto-Negotiation Advertisement Register
Auto-Negotiation Link Partner Ability Register
Auto-Negotiation Expansion Register
RESERVED
RESERVED
EXTENDED REGISTERS
0x0010
RO
PHYSTS
PHY Status Register
0x0011
RW
PHYSCR
PHY Specific Control Register
0x0012
RW
MISR1
MII Interrupt Status Register 1
0x0013
RW
MISR2
MII Interrupt Status Register 2
0x0014
RO
FCSCR
False Carrier Sense Counter Register
0x0015
RO
RECR
Receive Error Count Register
0x0016
RW
BISCR
BIST Control Register
0x0017
RO
RBR
0x0018
RW
LEDCR
RMII and Status Register
LED Control Register
0x0019
RW
PHYCR
PHY Control Register
0x001A
RW
10BTSCR
0x001B
RW
BICSR1
BIST Control and Status Register 1
0x001C
RO
BICSR2
BIST Control and Status Register 2
0x001D
RW
RESERVED
0x001E
RW
CDCR
0x001F
RW
PHYRCR
0x0020- 0x0041
RW
RESERVED
10Base-T Status/Control Register
RESERVED
Cable Diagnostic Control Register
PHY Reset Control Register
RESERVED
0x0042
RO
TXCPSR
0x0043- 0x00CF
RW
RESERVED
0x00D0
RW
VRCR
0x00D1-0x0154
RW
RESERVED
0x0155
RW
ALCDRR1
0x0156- 0x016F
RW
RESERVED
0x0170
RW
CDSCR1
Cable Diagnostic Specific Control Register 1
0x0171
RW
CDSCR2
Cable Diagnostic Specific Control Register 2
0x0172
RW
RESERVED
0x0173
RW
CDSCR3
0x0174-0x0176
RW
RESERVED
38
TX_CLK Phase Shift Register
RESERVED
Voltage Regulator Control Register
RESERVED
ALCD Control and Results 1
RESERVED
RESERVED
Cable Diagnostic Specific Control Register 3
RESERVED
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Table 8-1. Register Map (continued)
OFFSET HEX
ACCESS
TAG
0x0177
RW
CDSCR4
DESCRIPTION
0x0178- 0x017F
RW
RESERVED
0x0180
RO
CDLRR1
Cable Diagnostic Location Result Register 1
0x0181
RO
CDLRR2
Cable Diagnostic Location Result Register 2
0x0182
RO
CDLRR3
Cable Diagnostic Location Result Register 3
0x0183
RO
CDLRR4
Cable Diagnostic Location Result Register 4
0x0184
RO
CDLRR5
Cable Diagnostic Location Result Register 5
0x0185
RO
CDLAR1
Cable Diagnostic Amplitude Result Register 1
0x0186
RO
CDLAR2
Cable Diagnostic Amplitude Result Register 2
0x0187
RO
CDLAR3
Cable Diagnostic Amplitude Result Register 3
0x0188
RO
CDLAR4
Cable Diagnostic Amplitude Result Register 4
Cable Diagnostic Specific Control Register 4
RESERVED
0x0189
RO
CDLAR5
Cable Diagnostic Amplitude Result Register 5
0x018A
RW
CDGRR
Cable Diagnostic General Result Register
0x018B-0x0214
RW
RESERVED
0x0215
RW
ALCDRR2
RESERVED
ALCD Control and Results 2 Register
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
39
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
Table 8-2. Register Table
Addr
Tag
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Basic Mode Control
Register
Register Name
00h
BMCR
Reset
Loopback
Speed
Selection
Auto-Neg
Enable
IEEE
Power
Down
Isolate
Restart
Auto-Neg
Duplex
Mode
Collision
Test
Basic Mode Status
Register
01h
BMSR
100Base T4
100Base TX FDX
100Base TX HDX
10Base-T
FDX
10Base-T
HDX
PHY Identifier
Register 1
02h
PHYIDR 1
PHY Identifier
Register 2
03h
PHYIDR 2
Auto-Negotiation
Advertisement
Register
04h
ANAR
Next Page
Ind
Reserved
Remote
Fault
Reserved
ASM_DI R
PAUSE
100B-T4
100BTX_FD
100B-TX
10B-T_FD
10B-T
Protocol Selection[4:0]
Auto-Negotiation Link
Partner Ability
Register (Base Page)
05h
ANLPAR
Next Page
Ind
ACK
Remote
Fault
Reserved
ASM_DI R
PAUSE
100B-T4
100BTX_FD
100B-TX
10B-T_FD
10B-T
Protocol Selection[4:0]
Auto-Negotiation
Expansion Register
06h
ANER
Auto-Negotiation Next
Page TX Register
07h
ANNPTR
Next Page
Ind
Reserved
Message
Page
ACK2
TOG_TX
CODE
Auto-Negotiate Link
Partner Ability Page
Register
08h
ANLNPTR
Next Page
Ind
Reserved
Message
Page
ACK2
Toggle
CODE
Control Register 1
09h
CR1
Control Register 2
0Ah
CR2
Control Register 3
0Bh
CR3
RESERVED
0Ch
Reserved
Register Control
Register
0Dh
REGCR
Address or Data
Register
0Eh
ADDAR
Addr/ Data
RESERVED
0Fh
Reserved
Reserved
Reserved
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Link Status
Jabber
Detect
Extended
Capability
Reserved
MF
Preamble
Suppress
Auto-Neg
Complete
Remote
Fault
Auto-Neg
Ability
OUI MSB
OUI LSB
VNDR_ MDL
MDL_ REV
Reserved
Reserved
PDF
RMII
Enhance
Mode
TDR Auto
Run
Link Loss
Recovery
Fast Auto
MDI/X
Robust
Auto MDI/X
Fast AN
Enable
Reserved
Fast LinkUp in PD
Extended
FD Ability
Enhance
LED Link
Reserved
Polarity
Swap
MDI/X
Swap
Reserved
LP_NP_
ABLE
NP_ ABLE PAGE_ RX LP_AN_AB
LE
Fast AN Select
Isolate MII
in 100BT
HD
RXERR
During
IDLE
Fast RXDV
Detect
Reserved
Odd Nibble
Detect
Disable
RMII
Receive
Clock
Fast Link Down Sel
Reserved
Function
Reserved
DEVICE ADDRESS
space
40
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Table 8-3. Register Table, Extended Registers
Register Name
Addr
Tag
Bit 15
Bit 14
PHY Status Register
10h
PHYSTS
Reserved
MDI-X
Mode
PHY Specific Control
Register
11h
PHYSCR
Disable
PLL
Power
Save
Enable
MII Interrupt Status
Register 1
12h
MISR1
MII Interrupt Status
Register 2
13h
MISR2
MII Interrupt Control
Register
14h
FCSCR
Receive Error
Counter Register
15h
RECR
Reserved
Reserved
Auto-Neg
Error INT
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Polarity
Status
False
Carrier Sen
Latch
Signal
Detect
Descramb
Lock
Page
Receive
MII
Interrupt
Remote
Fault
Jabber
Detect
Auto-Neg
Status
Loopback
Status
Duplex
Status
Speed
Status
Link Status
Power Save Mode
Scrambler
Bypass
Reserved
Loopback Fifo Depth
COL FD
Enable
INT POL
TINT
INT_EN
INT_OE
Link Status
Speed INT
INT
Duplex
Mode INT
Auto-Neg
Comp INT
FC HF INT RE HF INT
Duplex
Mode En
Auto-Neg
Comp En
FC HF En
RE HF En
MDI
Crossover
INT
Sleep
Polarity INT Jabber INT
Mode INT
MDI
Crossover
EN
Sleep
Mode EN
Polarity EN Jabber EN
Receive Err
Latch
Page
Received
INT
Loopback
FIFO O/U
INT
Reserved
Link Status
Speed EN
En
Reserved
Reserved
Auto-Neg
Error EN
Page
Received
EN
Loopback
FIFO O/U
EN
Reserved
FCS Count
RX Err Count
BIST Control Register
16h
BISCR
Reserved
RMII Control, Status
Register
17h
RCSR
LED Control Register
18h
LEDCR
PHY Control Register
19h
PHYCR
BIST Packet Length
register
1Ah
10BTSCR
BIST Control, Status
Register 1
1Bh
BICSR1
BIST Control, Status
Register 2
1Ch
BICSR2
RESERVED
1Dh
Reserved
Cable Diagnostic
Control Register
1Eh
CDCR
Diagnostic
Start
Power Down Register
1Fh
PDR
Software
Reset
TX_CLK
42h
TXCPSR
Voltage Regulator
Control Register
D0h
VRCR
RESERVED
D1h154h
Reserved
ALCD Control and
Results 1
155h
ALCDRR1
RESERVED
156h16Fh
Reserved
PRBS
Count
Mode
Generate
PRBS
Packets
Packet Gen
Enable
PRBS
Checker
Lock
PRBS
Packet Gen
Checker
Status
SyncLoss
Power
Mode
Reserved
Transmit in
MII
Loopback
Reserved
Reserved
Auto MDI/X
Enable
Force
MDI/X
Pause RX
Status
Blink Rate
Pause TX
Status
MI Link
Status
Receiver
TH
Reserved
LED Speed
Polarity
Reserved
Squelch
Reserved
LED Link
Polarity
LED
Activity
Polarity
Reserved
Loopback Mode
RMII Mode
RMII
Revision
Drive LED
Speed
Drive LED
Link
Bypass
LED
Stretching
LED CFG
NLP
Disable
Reserved
RMII OVF
Status
RMII UNF
Status
Drive LED Speed LED
Activity
ON/OFF
ELAST BUF
Activity
LED
ON/OFF
Link LED
ON/OFF
PHY ADDR
Polarity
Status
BIST Err Count
Jabber
Disable
Reserved
BIST IPG Length
Reserved
Packet Length
Reserved
Reserved
Link Quality Link Quality
Software
Restart
VRPD
Phase Shift
En
Phase Shift Value
Reserved
Reserved
Diagnostic
Fail
Reserved
Reserved
alcd_start
Diagnostic
Done
Reserved
alcd_done
VR Control
alcd_out1
Reserved
alcd_ctrl
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
41
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
Table 8-3. Register Table, Extended Registers (continued)
Register Name
Addr
Tag
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Cable Diagnostic
Specific Control
Register 1
170h
CDSCR1
Reserved
Cross
Disable
TPTD
Bypass
TPRD
Bypass
Reserved
Cable Diagnostic
Specific Control
Register 2
171h
CDSCR2
RESERVED
172h
Cable Diagnostic
Specific Control
Register 3
173h
RESERVED
174h176h
Cable Diagnostic
Specific Control
Register 4
177h
CDSCR4
RESERVED
178h17Fh
Reserved
180h
CDLRR1
181h
CDLRR2
182h
CDLRR3
183h
CDLRR4
184h
CDLRR5
185h
CDLAR1
186h
CDLAR2
187h
CDLAR3
188h
CDLAR4
Cable Diagnostic
Location Results
Register 1-5
Cable Diagnostic
Amplitude Results
Register 1-5
189h
CDLAR5
18Ah
CDGRR
RESERVED
18Bh214h
Reserved
ALCD Control and
Results 2 Register
215h
ALCDRR2
42
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Average Cycles
Bit 3
Bit 2
Bit 1
Bit 0
Reserved
Reserved
CDSCR3
Cable Diagnostic
General Results
Register
Bit 10
TDR pulse control
Cable length
Reserved
Short cables TH
Reserved
TPTD/RD Peak Location
Reserved
TPTD/RD Peak Amplitude
Reserved
TPTD/RD Peak Amplitude
Cross
TPTD Peak TPTD Peak TPTD Peak TPTD Peak TPTD Peak TPRD Peak TPRD Peak TPRD Peak TPRD Peak TPRD Peak
Detect on
Polarity 5
Polarity 4
Polarity 3
Polarity 2
Polarity 1
Polarity 5
Polarity 4
Polarity 3
Polarity 2
Polarity 1
TPTD
alcd_out2
Cross
Detect on
TPRD
Above 5
TPTD
Peaks
Above 5
TPTD
Peaks
Reserved
Reserved
alcd_out3
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
8.1
Register Definition
In
•
•
•
•
•
•
•
•
•
•
8.1.1
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
the register definitions under the ‘Default’ heading, the following definitions hold true:
COR = Clear on Read
Pin_Strap = Default value loads from strapping pin after reset
LH = Latched High and held until read, based upon the occurrence of the corresponding event
LL = Latched Low and held until read, based upon the occurrence of the corresponding event
RO = Read Only access
RO/COR = Read Only, Clear on Read
RO/P = Read Only, Permanently set to a default value
RW = Read Write access
RW/SC = Read Write Access/Self Clearing bit
SC = Register sets on event occurrence and Self-Clears when event ends
Basic Mode Control Register (BMCR)
Table 8-4. Basic Mode Control Register (BMCR), address 0x0000
BIT
15
BIT NAME
Reset
DEFAULT
0, RW/SC
DESCRIPTION
PHY Software Reset:
1 = Initiate software Reset / Reset in Process
0 = Normal operation
Writing a 1 to this bit resets the PHY. When the reset operation is done, this bit is cleared to
0 automatically. The configuration is relatched.
14
MII Loopback
0, RW
MII Loopback:
1 = MII Loopback enabled
0 = Normal operation
When MII loopback mode is activated, the transmitter data presented on MII TXD is looped
back to MII RXD internally.
13
Speed Selection
1, Pin_Strap
Speed Select:
When auto-negotiation is disabled writing to this bit allows the port speed to be selected.
1 = 100Mbs
0 = 10Mbs
12
Auto-Negotiation
Enable
1, Pin_Strap
Auto-Negotiation Enable:
1 = Auto-Negotiation Enabled – bits 8 and 13 of this register are ignored when this bit is
set.
0 = Auto-Negotiation Disabled – bits 8 and 13 determine the port speed and duplex
mode.
11
IEEE Power
Down
0, RW
Power Down:
1 = Enables IEEE power down mode
0 = Normal operation
Setting this bit powers down the PHY. Only minimal register functionality is enabled during
the power down condition. To control the power down mechanism, this bit is ORed with the
input from the INT/PWDN pin. When the active low INT/PWDN is asserted, this bit is set.
10
Isolate
0, RW
Isolate:
1 = Isolates the Port from the MII with the exception of the serial management
0 = Normal operation
9
Restart AutoNegotiation
0, RW/SC
Restart Auto-Negotiation:
1 = Restart Auto-Negotiation. Re-initiates the Auto-Negotiation process. If AutoNegotiation is disabled (bit 12 = 0), this bit is ignored. This bit is self-clearing and will
return a value of 1 until Auto-Negotiation is initiated, whereupon it will self-clear.
Operation of the Auto-Negotiation process is not affected by the management entity
clearing this bit.
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
43
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
Table 8-4. Basic Mode Control Register (BMCR), address 0x0000 (continued)
BIT
BIT NAME
DEFAULT
DESCRIPTION
0 = Normal operation
Re-initiates the Auto-Negotiation process. If Auto-Negotiation is disabled (bit 12 = 0), this bit
is ignored. This bit is self-clearing and will return a value of 1 until Auto-Negotiation is
initiated, whereupon it self-clears. Operation of the Auto-Negotiation process is not affected
by the management entity clearing this bit.
8
Duplex Mode
1, Pin_Strap
Duplex Mode:
When auto-negotiation is disabled writing to this bit allows the port Duplex capability to be
selected.
1 = Full Duplex operation
led control
7
Collision Test
0, RW
0 = Half Duplex operation
Collision Test:
1 = Collision test enabled
0 = Normal operation
When set, this bit causes the COL signal to be asserted in response to the assertion of
TX_EN within 512 bit times. The COL signal is de-asserted within 4 bit times in response to
the de-assertion of TX_EN.
6:0
44
RESERVED
0, RO
RESERVED: Write ignored, read as 0.
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
8.1.2
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Basic Mode Status Register (BMSR)
Table 8-5. Basic Mode Status Register (BMSR), address 0x0001
BIT
BIT NAME
DEFAULT
15
100Base-T4
0, RO/P
14
100Base-TX
Full Duplex
1, RO/P
100Base-TX
Half Duplex
1, RO/P
10Base-T
Full Duplex
1, RO/P
10Base-T Half
Duplex
1, RO/P
DESCRIPTION
100Base-T4 Capable:
This protocol is not available. Always 0 = Device does not perform 100Base-T4 mode.
100Base-TX Full Duplex Capable:
1 = Device able to perform 100Base-TX in full duplex mode
0 = Device not able to perform 100Base-TX in full duplex mode
13
100Base-TX Half Duplex Capable:
1 = Device able to perform 100Base-TX in half duplex mode
0 = Device not able to perform 100Base-TX in half duplex mode
12
10Base-T Full Duplex Capable:
1 = Device able to perform 10Base-T in full duplex mode
0 = Device not able to perform 10Base-T in full duplex mode
11
10Base-T Half Duplex Capable:
1 = Device able to perform 10Base-T in half duplex mode
0 = Device not able to perform 10Base-T in half duplex mode
10:7
RESERVED
0, RO
RESERVED: Write as 0, read as 0
6
MF Preamble
Suppression
1, RO/P
Preamble suppression Capable:
1 = Device able to perform management transaction with preamble suppressed, 32-bits of
preamble needed only once after reset, invalid opcode or invalid turnaround.
0 = Device will not perform management transaction with preambles suppressed
5
AutoNegotiation
Complete
0, RO
Auto-Negotiation Complete:
1 = Auto-Negotiation process complete
0 = Auto-Negotiation process not complete (either still in process, disabled, or reset)
4
Remote Fault
0, RO/LH
Remote Fault:
1 = Remote Fault condition detected (cleared on read or by reset). Fault criteria: Far End Fault
Indication or notification from Link Partner of Remote Fault.
0 = No remote fault condition detected
3
AutoNegotiation
Ability
1, RO/P
Link Status
0, RO/LL
Auto Negotiation Ability:
1 = Device is able to perform Auto-Negotiation
0 = Device is not able to perform Auto-Negotiation
2
Link Status:
1 = Valid link established (for either 10 or 100Mbs operation)
0 = Link not established
1
Jabber Detect
0, RO/LH
Jabber Detect: This bit only has meaning in 10Mbs mode.
1 = Jabber condition detected
0 = No Jabber. condition detected
This bit is implemented with a latching function, such that the occurrence of a jabber condition
causes it to set until it is cleared by a read to this register by the management interface or by a
reset.
0
Extended
Capability
1, RO/P
Extended Capability:
1 = Extended register capabilities
0 = Basic register set capabilities only
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
45
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
8.1.3
www.ti.com
PHY Identifier Register 1 (PHYIDR1)
The PHY Identifier Registers 1 and 2 together form a unique identifier for the TLK10x. The identifier
consists of a concatenation of the Organizationally Unique Identifier (OUI), the vendor's model number
and the model revision number. A PHY may return a value of zero in each of the 32 bits of the PHY
Identifier if desired. The PHY Identifier is intended to support network management. The Texas
Instruments IEEE-assigned OUI is 080028h, implemented as Reg 0x2 [15:0] = OUI[21:6] = 2000(h) and
Reg 0x3 [15:10] = OUI[5:0] = A(h).
Table 8-6. PHY Identifier Register 1 (PHYIDR1), address 0x0002
BIT
BIT NAME
15:0 OUI_MSB
8.1.4
DEFAULT
DESCRIPTION
<0010 0000 0000
0000>,
RO/P
OUI[21:6] = 2000(h): The most significant two bits of the OUI are ignored (the IEEE
standard refers to these as bits 1 and 2).
PHY Identifier Register 2 (PHYIDR2)
Table 8-7. PHY Identifier Register 2 (PHYIDR2), address 0x0003
BIT
15:10
BIT NAME
DEFAULT
DESCRIPTION
OUI_LSB
<101000>,
RO/P
OUI[5:0] = 28(h)
9:4
VNDR_MDL
<100001>,
RO/P
Vendor Model Number:
3:0
MDL_REV
<0001>, RO/P
The six bits of vendor model number are mapped from bits 9 to 4 (most significant bit to bit 9).
Model Revision Number:
Four bits of the vendor model revision number are mapped from bits 3 to 0 (most significant bit to
bit 3). This field is incremented for all major device changes.
46
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
8.1.5
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Auto-Negotiation Advertisement Register (ANAR)
This register contains the advertised abilities of this device as they are transmitted to its link partner during
Auto-Negotiation.
Table 8-8. Auto Negotiation Advertisement Register (ANAR), address 0x0004
BIT
15
BIT NAME
NP
DEFAULT
0, RW
DESCRIPTION
Next Page Indication:
0 = Next Page Transfer not desired
1 = Next Page Transfer desired
14
RESERVED
13
RF
0, RO/P
0, RW
RESERVED by IEEE: Writes ignored, Read as 0
Remote Fault:
1 = Advertises that this device has detected a Remote Fault
0 = No Remote Fault detected
12
RESERVED
0, RW
RESERVED for Future IEEE use: Write as 0, Read as 0
11
ASM_DIR
0, RW
Asymmetric PAUSE Support for Full Duplex Links: The ASM_DIR bit indicates that asymmetric
PAUSE is supported.
1 = Asymmetric PAUSE implemented. Advertise that the DTE/MAC has implemented both the
optional MAC control sublayer and the pause function as specified in clause 31 and annex 31B
of IEEE802.3u.
0 = Asymmetric PAUSE not implemented
Encoding and resolution of PAUSE bits is defined in IEEE 802.3 Annex 28B, Tables 28B-2 and 28B3, respectively. Pause resolution status is reported in PHYCR[13:12].
10
PAUSE
0, RW
PAUSE Support for Full Duplex Links: The PAUSE bit indicates that the device is capable of
providing the symmetric PAUSE functions as defined in Annex 31B.
1 = MAC PAUSE implemented. Advertise that the DTE (MAC) has implemented both the optional
MAC control sub-layer and the pause function as specified in clause 31 and annex 31B of
802.3u.
0 = MAC PAUSE not implemented
Encoding and resolution of PAUSE bits is defined in IEEE 802.3 Annex 28B, Tables 28B-2 and 28B3, respectively. Pause resolution status is reported in PHYCR[13:12].
9
100B-T4
0, RO/P
100Base-T4 Support:
1 = 100Base-T4 is supported by the local device
0 = 100Base-T4 not supported
8
100B-TX_FD
1, RW
100Base-TX Full Duplex Support:
1 = 100Base-TX Full Duplex is supported by the local device
0 = 100Base-TX Full Duplex not supported
7
100B-TX
1, RW
100Base-TX Support:
1 = 100Base-TX is supported by the local device
0 = 100Base-TX not supported
6
10B-T_FD
1, RW
10Base-T Full Duplex Support:
1 = 10Base-T Full Duplex is supported by the local device
0 = 10Base-T Full Duplex not supported
5
10B-T
1, RW
10Base-T Support:
1 = 10Base-T is supported by the local device
0 = 10Base-T not supported
4:0 Selector
<00001>, RW
Protocol Selection Bits:
These bits contain the binary encoded protocol selector supported by this port. <00001> indicates that
this device supports IEEE 802.3u.
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
47
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
8.1.6
www.ti.com
Auto-Negotiation Link Partner Ability Register (ANLPAR) (BASE Page)
This register contains the advertised abilities of the Link Partner as received during Auto-Negotiation. The
content changes after the successful auto-negotiation if Next-pages are supported.
Table 8-9. Auto-Negotiation Link Partner Ability Register (ANLPAR) (BASE Page), address 0x0005
BIT
15
BIT NAME
DEFAULT
NP
0, RO
DESCRIPTION
Next Page Indication:
0 = Link Partner does not desire Next Page Transfer
1 = Link Partner desires Next Page Transfer
14
ACK
0, RO
Acknowledge:
1 = Link Partner acknowledges reception of the ability data word
0 = Not acknowledged. The Auto-Negotiation state machine will automatically control the this bit
based on the incoming FLP bursts.
13
RF
0, RO
Remote Fault:
1 = Remote Fault indicated by Link Partner
0 = No Remote Fault indicated by Link Partner
12
RESERVED
0, RO
RESERVED for Future IEEE use: Write as 0, read as 0
11
ASM_DIR
0, RO
ASYMMETRIC PAUSE:
1 = Asymmetric pause is supported by the Link Partner
0 = Asymmetric pause is not supported by the Link Partner
10
PAUSE
0, RO
PAUSE:
1 = Pause function is supported by the Link Partner
0 = Pause function is not supported by the Link Partner
9
100B-T4
0, RO
100Base-T4 Support:
1 = 100Base-T4 is supported by the Link Partner
0 = 100Base-T4 is not supported by the Link Partner
8
100BTX_FD
0, RO
100Base-TX Full Duplex Support:
1 = 100Base-TX Full Duplex is supported by the Link Partner
0 = 100Base-TX Full Duplex is not supported by the Link Partner
7
100B-TX
0, RO
100Base-TX Support:
1 = 100Base-TX is supported by the Link Partner
0 = 100Base-TX is not supported by the Link Partner
6
10B-T_FD
0, RO
10Base-T Full Duplex Support:
1 = 10Base-T Full Duplex is supported by the Link Partner
0 = 10Base-T Full Duplex is not supported by the Link Partner
5
10B-T
0, RO
10Base-T Support:
1 = 10Base-T is supported by the Link Partner
0 = 10Base-T is not supported by the Link Partner
4:0 Selector
<0 0000>, RO
Protocol Selection Bits:
Link Partner’s binary encoded protocol selector.
48
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
8.1.7
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Auto-Negotiate Expansion Register (ANER)
This register contains additional Local Device and Link Partner status information.
Table 8-10. Auto-Negotiate Expansion Register (ANER), address 0x0006
BIT
BIT NAME
15:5 RESERVED
4
PDF
DEFAULT
DESCRIPTION
0, RO
RESERVED: Writes ignored, Read as 0.
0, RO
Parallel Detection Fault:
1 = Fault detected via the Parallel Detection function
0 = No fault detected
3
LP_NP_ABL
E
0, RO
Link Partner Next Page Able:
1 = Link Partner does support Next Page
0 = Link Partner does not support Next Page
2
NP_ABLE
1, RO/P
Next Page Able:
1 = Indicates local device is able to send additional Next Pages
0 = Indicates local device is not able to send additional Next Pages
1
PAGE_RX
0, RO/COR
Link Code Word Page Received:
1 = Link Code Word has been received, cleared on a read
0 = Link Code Word has not been received
0
LP_AN_ABL
E
0, RO
Link Partner Auto-Negotiation Able:
1 = indicates that the Link Partner supports Auto-Negotiation
0 = indicates that the Link Partner does not support Auto-Negotiation
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
49
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
8.1.8
www.ti.com
Auto-Negotiate Next Page Transmit Register (ANNPTR)
This register contains the next page information sent by this device to its Link Partner during AutoNegotiation.
Table 8-11. Auto-Negotiation Next Page Transmit Register (ANNPTR), address 0x0007
BIT
15
BIT NAME
NP
DEFAULT
0, RW
DESCRIPTION
Next Page Indication:
0 = No other Next Page Transfer desired
1 = Another Next Page desired
14
RESERVED
0, RO
RESERVED: Writes ignored, read as 0
13
MP
1, RW
Message Page:
1 = Message Page
0 = Unformatted Page
12
ACK2
0, RW
Acknowledge2:
1 = Will comply with message
0 = Cannot comply with message
Acknowledge2 is used by the next page function to indicate that Local Device has the ability
to comply with the message received.
11
TOG_TX
0, RO
Toggle:
1 = Value of toggle bit in previously transmitted Link Code Word was 0
0 = Value of toggle bit in previously transmitted Link Code Word was 1
Toggle is used by the Arbitration function within Auto-Negotiation to synchronize with the Link
Partner during Next Page exchange. This bit always takes the opposite value of the Toggle
bit in the previously exchanged Link Code Word.
10:0
CODE
<000 0000 0001>, This field represents the code field of the next page transmission. If the MP bit is set (bit 13 of
RW
this register), then the code is interpreted as a Message Page, as defined in annex 28C of
IEEE 802.3u. Otherwise, the code is interpreted as an Unformatted Page, and the
interpretation is application specific.
The default value of the CODE represents a Null Page as defined in Annex 28C of IEEE
802.3u.
50
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
8.1.9
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Auto-Negotiation Link Partner Ability Next Page Register (ANLNPTR)
This register contains the next page information sent by this device to its Link Partner during AutoNegotiation.
Table 8-12. Auto-Negotiation Link Partner Ability Register Next Page (ANLNPTR), address 0x0008
BIT
15
BIT NAME
NP
DEFAULT
0, RO
DESCRIPTION
Next Page Indication:
1 = No other Next Page Transfer desired
0 = Another Next Page desired
14
ACK
0, RO
Acknowledge:
1 = Link Partner acknowledges reception of the ability data word
0 = Not acknowledged
The Auto-Negotiation state machine automatically controls this bit based on the incoming FLP
bursts. Software should not attempt to write to this bit.
13
MP
1, RO
Message Page:
1 = Message Page
0 = Unformatted Page
12
ACK2
0, RO
Acknowledge2:
1 = Link Partner has the ability to comply to next-page message
0 = Link Partner cannot comply to next-page message
Acknowledge2 is used by the next page function to indicate that Local Device has the ability to
comply with the message received.
11
Toggle
0, RO
Toggle:
1 = Value of toggle bit in previously transmitted Link Code Word was 0
0 = Value of toggle bit in previously transmitted Link Code Word was 1
Toggle is used by the Arbitration function within Auto-Negotiation to synchronize with the Link
Partner during Next Page exchange. This bit always takes the opposite value of the Toggle bit in
the previously exchanged Link Code Word.
10:0 CODE
<000 0000 0001>,
RO
Code:
This field represents the code field of the next page transmission. If the MP bit is set (bit 13 of
this register), then the code is interpreted as a Message Page, as defined in annex 28C of IEEE
802.3u. Otherwise, the code is interpreted as an Unformatted Page, and the interpretation is
application specific.
The default value of the CODE represents a Null Page as defined in Annex 28C of IEEE 802.3u.
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
51
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
8.1.10 Control register 1 (CR1)
Table 8-13. Control register 1 (CR1), address 0x0009
BIT
15:10
9
BIT NAME
DEFAULT
DESCRIPTION
RESERVED
1, RW
RESERVED
RMII
Enhanced
Mode
0, RW
RMII Enhanced Mode:
1 = Enable RMII Enhanced Mode
0 = RMII operates in normal mode
In normal mode, If the line is not idle CRS_DV goes high. As soon as the False Carrier is
detected, RX_ER is asserted and RXD is set to “2”. This situation remains for the duration
of the receive event. While in enhanced mode, CRS_DV is disqualified and de-asserted
when the False Carrier detected. This status also remains for the duration of the receive
event. In addition in normal mode, the start of the packet is intact. Each symbol error is
indicated by setting RX_ER high. The data on RXD is replaced with “1” starting with the
first symbol error. While in enhanced mode, the CRS_DV is de-asserted with the first
symbol error.
8
TDR
AUTORUN
0, RW
TDR Auto Run at link down:
1 = Enable execution of TDR procedure after link down event
0 = Disable automatic execution of TDR
7
Link Loss
Recovery
0, RW
Link Loss Recovery:
1 = Enable Link Loss Recovery mechanism. This mode allow recovery from short
interference and continue to hold the link up for period of additional few mSec till
the short interference will gone and the signal is OK.
0 = Normal Link Loss operation. Link status will go down approximately 250uSec from
signal loss.
6
Fast Auto
MDI-X
0, RW
Fast Auto MDI/MDIX:
1 = Enable Fast Auto MDI/MDIX mode
0 = Normal Auto MDI/MDIX mode.
If both link partners are configured to work in Force 100Base-TX mode (Auto-Negotiation
is disabled), this mode enables Automatic MDI/MDIX resolution in a short time.
5
Robust Auto
MDI-X
0, RW
Robust Auto MDI-X :
1 = Enable Robust Auto MDI/MDIX resolution
0 = Normal Auto MDI/MDIX mode
If link partners are configured to operational modes that are not supported by normal Auto
MDI/MDIX mode (like Auto-Neg versus Force 100Base-TX or Force 100Base-TX versus
Force 100Base-TX), this Robust Auto MDI/MDIX mode allows MDI/MDIX resolution and
prevents deadlock.
4
Fast AN En
0, RW
Fast AN En:
1 = Enable Fast Auto-Negotiation mode – The PHY auto-negotiates using Timer
setting according to Fast AN Sel bits (bits 3:2 this register)
0 = Disable Fast Auto-Negotiation mode – The PHY auto-negotiates using normal
Timer setting
Adjusting these bits reduces the time it takes to Auto-negotiate between two PHYs. Note:
When using this option care must be taken to maintain proper operation of the system.
While shortening these timer intervals may not cause problems in normal operation, there
are certain situations where this may lead to problems.
52
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Table 8-13. Control register 1 (CR1), address 0x0009 (continued)
BIT
BIT NAME
3:2
Fast AN Sel
DEFAULT
0, RW
DESCRIPTION
Fast Auto-Negotiation Select bits:
Fast AN
Select
Break
Link
Timer
Link Fail
Inhibit
Timer
Auto-Neg Wait Timer
<00>
80
50
35
<01>
120
75
50
<10>
240
150
100
<11>
NA
NA
NA
Adjusting these bits reduces the time it takes to Auto-negotiate between two PHYs. In
Fast AN mode, both PHYs should be configured to the same configuration. These 2 bits
define the duration for each state of the Auto Negotiation process according to the table
above. The new duration time must be enabled by setting “Fast AN En” - bit 4 of this
register. Note: Using this mode in cases where both link partners are not configured to
the same Fast Auto-negotiation configuration might produce scenarios with unexpected
behavior.
1
Fast RXDV
Detection
0, RW
Fast RXDV Detection:
1 = Enable assertion high of RX_DV on receive packet due to detection of /J/ symbol
only. If a consecutive /K/ does not appear, RX_ER is generated.
0 = Disable Fast RX_DV detection. The PHY operates in normal mode - RX_DV
assertion after detection of /J/K/.
0
RESERVED
1, RW
RESERVED
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
53
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
8.1.11 Control register 2 (CR2)
Table 8-14. Control register 2 (CR2), address 0x000A
BIT
BIT NAME
DEFAULT
DESCRIPTION
15:14
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
13:7
RESERVED
0, RW
RESERVED
Fast Link-Up in
Parallel Detect
0, RW
Fast Link-Up in Parallel Detect Mode:
6
1 = Enable Fast Link-Up time During Parallel Detection
0 = Normal Parallel Detection link establishment
In Fast Auto MDI-X and in Robust Auto MDI-X modes (bits 6 and 5 in register CR1), this
bit is automatically set.
5
Extended FD
Ability
0, RW
Extended Full-Duplex Ability:
1 = Force Full-Duplex while working with link partner in forced 100B-TX. When the
PHY is set to Auto-Negotiation or Force 100B-TX and the link partner is operated
in Force 100B-TX, the link is always Full Duplex
0 = Disable Extended Full Duplex Ability. Decision to work in Full Duplex or Half
Duplex mode follows IEEE specification.
4
Enhanced LED
Link
0, RW
Isolate MII in
100BT HD
0, RW
RXERR During
IDLE
1, RW
Odd-Nibble
Detection
Disable
0, RW
Enhanced LED Link Functionality:
1 = LED Link is ON only when link is established in 100B-TX Full Duplex mode.
0 = LED Link is ON when link is established.
3
Isolate MII outputs when FD Link @ 100BT is not achievable:
1 = When HD link established in 100B-TX MII outputs are isolated
0 = Normal MII outputs operation
2
Detection of Receive Symbol Error During IDLE State:
1 = Enable detection of Receive symbol error during IDLE state
0 = Disable detection of Receive symbol error during IDLE state.
1
Detection of Transmit Error:
1 = Disable detection of transmit error in odd-nibble boundary
0 = Enable detection of de-assertion of TX_EN on an odd-nibble boundary. In this case
TX_EN is extended by one additional TX_CLK cycle and behaves as if TX_ER
were asserted during that additional cycle.
0
RMII Receive
Clock
0, RW
RMII Receive Clock:
1 = RMII Data (RXD [1:0]) is sampled and referenced to RX_CLK
0 = RMII Data (RXD [1:0]) is sampled and referenced to XI
54
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
8.1.12 Control Register 3 (CR3)
Table 8-15. Control register 3 (CR3), address 0x000B
BIT
BIT NAME
15:7 RESERVED
6
Polarity
Swap
DEFAULT
DESCRIPTION
0, RO
RESERVED: Writes ignored, read as 0.
0, RW
Polarity Swap:
1 = Inverted polarity on both pairs: TPTD+ ↔ TPTD-, TPRD+ ↔ TPRD0 = Normal polarity
Port Mirror function: To Enable port mirroring, set bit 5 and this bit high.
5
MDI/MDIX
Swap
0, RW
MDI/MDIX Swap:
1 = Swap MDI pairs (Receive on TPTD pair, Transmit on TPRD pair)
0 = MDI pairs normal (Receive on TPRD pair, Transmit on TPTD pair)
Port Mirror function: To Enable port mirroring, set this bit and bit 6 high.
4
RESERVED
0, RW
RESERVED
3:0
Fast Link
Down Mode
0, RW
Fast Link Down Modes:
Bit 3 Drop the link based on RX Error count of the MII interface – When a predefined number
of 32 RX Error occurrences in a 10µs interval is reached, the link will be dropped.
Bit 2 Drop the link based on MLT3 Errors count (Violation of the MLT3 coding in the DSP
output) – When a predefined number of 20 MLT3 Error occurrences in a 10µs interval is
reached, the link will be dropped.
Bit 1 Drop the link based on Low SNR Threshold – When a predefined number of 20
Threshold crossing occurrences in a 10µs interval is reached, the link will be dropped.
Bit 0 Drop the link based on Signal/Energy loss indication – When the Energy detector
indicates Energy Loss, the link will be dropped. Typical reaction time is 10µs.
The Fast Link Down function is an OR of all these 4 options, so the designer can enable
combinations of these conditions.
8.2
Extended Register Addressing
REGCR (0x000D) and ADDAR (0x000E) allow read/write access to the extended register set (addresses
above 0x000F) using indirect addressing.
• REGCR [15:14] = 00: A write to ADDAR modifies the extended register set address register. This
address register must be initialized in order to access any of the registers within the extended register
set.
• REGCR [15:14] = 01: A read/write to ADDAR operates on the register within the extended register set
selected (pointed to) by the value in the address register. The address register contents (pointer)
remain unchanged.
• REGCR [15:14] = 10: A read/write to ADDAR operates on the register within the extended register set
selected (pointed to) by the value in the address register. After that access is complete, for both reads
and writes, the value in the address register is incremented.
• REGCR [15:14] = 11: A read/write to ADDAR operates on the register within the extended register set
selected (pointed to) by the value in the address register. After that access is complete, for write
accesses only, the value in the address register is incremented. For read accesses, the value of the
address register remains unchanged.
8.2.1
Register Control Register (REGCR)
This register is the MDIO Manageable MMD access control. In general, register REGCR (4:0) is the
device address DEVAD that directs any accesses of the ADDAR (0x000E) register to the appropriate
MMD. REGCR also contains selection bits for auto increment of the data register. This register contains
the device address to be written to access the extended registers. Write 0x1F into bits 4:0 of this register.
REGCR also contains selection bits (15:14) for the address auto-increment mode of ADDAR.
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
55
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
Table 8-16. Register Control Register (REGCR), address 0x000D
BIT
BIT NAME
15:14
Function
13:5
4:0
8.2.2
DEFAULT
DESCRIPTION
0, RW
00
01
10
11
= Address
= Data, no post increment
= Data, post increment on read and write
= Data, post increment on write only
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
DEVAD
0, RW
Device Address: In general, these bits [4:0] are the device address DEVAD that directs any
accesses of ADDAR register (0x000E) to the appropriate MMD. Specifically, the TLK10x uses the
vendor specific DEVAD [4:0] = “11111” for accesses. All accesses through registers REGCR and
ADDAR should use this DEVAD. Transactions with other DEVAD are ignored.
Address or Data Register (ADDAR)
This register is the address/data MMD register. ADDAR is used in conjunction with REGCR register
(0x000D) to provide the access by indirect read/write mechanism to the extended register set.
Table 8-17. Data Register (ADDAR), address 0x000E
BIT
BIT NAME
15:0 Addr/data
56
DEFAULT
0, RW
DESCRIPTION
If REGCR register 15:14 = 00, holds the MMD DEVAD's address register, otherwise holds the
MMD DEVAD's data register
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
8.3
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
PHY Status Register (PHYSTS)
This register provides quick access to commonly accessed PHY control status and general information.
Table 8-18. PHY Status Register (PHYSTS), address 0x0010
BIT
NAME
DEFAULT
15
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
DESCRIPTION
14
MDI-X Mode
0,RO
MDI-X mode as reported by the Auto-Negotiation state machine:
1 = MDI pairs swapped (Receive on TPTD pair, Transmit on TPRD pair)
0 = MDI pairs normal (Receive on TRD pair, Transmit on TPTD pair)
This bit will be affected by the settings of the AMDIX_EN and FORCE_MDIX bits in the PHYCR
register. When MDIX is enabled, but not forced, this bit will update dynamically as the Auto-MDIX
algorithm swaps between MDI and MDI-X configurations.
13
Receive Error
Latch
0,RO/LH
Receive Error Latch:
1 = Receive error event has occurred since last read of RXERCNT register (0x0015)
0 = No receive error event has occurred
This bit will be cleared upon a read of the RECR register
12
Polarity Status
0,RO
Polarity Status:
1 = Inverted Polarity detected
0 = Correct Polarity detected
This bit is a duplication of bit 4 in the 10BTSCR register (0x001A). This bit will be cleared upon a read
of the 10BTSCR register, but not upon a read of the PHYSTS register.
11
False Carrier
Sense Latch
0,RO/LH
False Carrier Sense Latch:
1 = False Carrier event has occurred since last read of FCSCR register (0x0014)
0 = No False Carrier event has occurred
This bit will be cleared upon a read of the FCSR register.
10
Signal Detect
0,RO/LL
Signal Detect:
Active high 100Base-TX unconditional Signal Detect indication from PMD
9
Descrambler
Lock
0,RO/LL
8
Page
Received
0,RO
Descrambler Lock:
Active high 100Base-TX Descrambler Lock indication from PMD
Link Code Word Page Received:
1 = A new Link Code Word Page has been received. This bit is a duplicate of Page Received (bit 1)
in the ANER register and it is cleared on read of the ANER register (0x0006).
0 = Link Code Word Page has not been received.
This bit will not be cleared upon a read of the PHYSTS register.
7
MII Interrupt
0,RO
MII Interrupt Pending:
1 = Indicates that an internal interrupt is pending. Interrupt source can be determined by reading the
MISR Register (0x0012). Reading the MISR will clear this Interrupt bit indication.
0 = No interrupt pending
6
Remote Fault
0,RO
Remote Fault:
1 = Remote Fault condition detected. Fault criteria: notification from Link Partner of Remote Fault
via Auto-Negotiation. Cleared on read of BMSR register (0x0001) or by reset.
0 = No remote fault condition detected
5
Jabber Detect
0,RO
Jabber Detect:
1 = Jabber condition detected. This bit has meaning only in 10 Mb/s mode. This bit is a duplicate of
the Jabber Detect bit in the BMSR register (0x0001).
0 = No Jabber
This bit will not be cleared upon a read of the PHYSTS register.
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
57
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
Table 8-18. PHY Status Register (PHYSTS), address 0x0010 (continued)
BIT
4
NAME
DEFAULT
Auto-Neg
Status
0,RO
MII Loopback
Status
0,RO
Duplex Status
0,RO
DESCRIPTION
Auto-Negotiation Status:
1 = Auto-Negotiation complete
0 = Auto-Negotiation not complete
3
MII Loopback:
1 = Loopback active (enabled)
0 = Normal operation
2
Duplex Status:
1 = Full duplex mode
0 = Half duplex mode
This bit indicates duplex status and is determined from Auto-Negotiation or Forced Modes. Therefore, it
is only valid if Auto-Negotiation is enabled and complete and there is a valid link or if Auto-Negotiation
is disabled and there is a valid link.
1
Speed Status
0,RO
Speed Status:
1 = 10 Mb/s mode
0 = 100 Mb/s mode
This bit indicates the status of the speed and is determined from Auto-Negotiation or Forced Modes.
Speed Status is only valid if Auto-Negotiation is enabled and complete and there is a valid link or if
Auto-Negotiation is disabled and there is a valid link.
0
Link Status
0,RO
Link Status:
1 = Valid link established (for either 10 or 100 Mb/s operation). This bit is a duplicate of the Link
Status bit in the BMSR register (0x0001).
0 = Link not established
This bit will not be cleared upon a read of the PHYSTS register.
8.4
PHY Specific Control Register (PHYSCR)
This register implements the PHY Specific Control register. This register allows access to general
functionality inside the PHY to enable operation in reduced power modes and control interrupt mechanism.
Table 8-19. PHY Specific Control Register (PHYSCR), address 0x0011
BIT
NAME
DEFAULT DESCRIPTION
15
Disable PLL
0,RW
Disable PLL:
1 = Disable internal clocks Circuitries
0 = Normal mode of operation
Note: Clock Circuitry can be disabled only in IEEE power-down mode
14
PS Enable
0,RW
Power Save Modes Enable:
1 = Enable power save modes
0 = Normal mode of operation
13:12 PS Modes
58
<00>,RW
Power Save Modes:
Power Mode
Name
Description
<00>
Normal
Normal operation mode. PHY is fully functional
<01>
IEEE power
down
Low Power mode that shut down all internal circuitry
beside SMI functionality.
<10>
Active Sleep
Low Power Active WOL mode that shut down all internal
circuitry beside SMI and energy detect functionalities. In
this mode the PHY sends NLP every 1.4 Sec to wake up
link-partner. Automatic power-up is done when link partner
is detected.
<11>
Passive
Sleep
Low Power WOL mode that shut down all internal circuitry
beside SMI and energy detect functionalities. Automatic
power-up is done when link partner is detected.
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Table 8-19. PHY Specific Control Register (PHYSCR), address 0x0011 (continued)
BIT
NAME
DEFAULT DESCRIPTION
11
Scrambler
Bypass
0,RW
10
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
9:8
Loopback
FIFO Depth
<01>,RW
Far-End Loopback FIFO Depth:
Scrambler Bypass:
1 = Scrambler bypass enabled
0 = Scrambler bypass disabled
00 = 4 nibbles FIFO
01 = 5 nibbles FIFO
10 = 6 nibbles FIFO
11 = 8 nibbles FIFO
This FIFO is used to adjust RX (recovered) clock rate to TX clock rate. FIFO depth need to be set
based on expected maximum packet size and clock accuracy. Default value sets to 5 nibbles.
7:5
4
RESERVED
<000>,
RO
RESERVED: Writes ignored, read as 0.
COL FD
Enable
0, RW
Collision in Full-Duplex Mode:
INT POL
1,RW
1 = Enable generating Collision signaling in Full Duplex
0 = Disable Collision indication in Full Duplex mode. Collision will be active in Half Duplex only.
3
Interrupt Polarity:
1 = Steady state (normal operation) is 1 logic and during interrupt is 0 logic.
0 = Steady state (normal operation) is 0 logic and during interrupt is 1 logic.
2
tint
0,RW
Test Interrupt:
1 = Generate an interrupt
0 = Do not generate interrupt
Forces the PHY to generate an interrupt to facilitate interrupt testing. Interrupts will continue to be
generated as long as this bit remains set.
1
INT_EN
0,RW
Interrupt Enable:
1 = Enable event based interrupts
0 = Disable event based interrupts
Enable interrupt dependent on the event enables in the MISR register (0x0012).
0
INT_OE
0,RW
Interrupt Output Enable:
1 = INT / PWDN is an Interrupt Output
0 = INT / PWDN is a Power Down
Enable active low interrupt events via the INT / PWDN pin by configuring the INT / PWDN pin as an
output.
8.5
MII Interrupt Status Register 1 (MISR1)
This register contains events status and enables for the interrupt function. If an event has occurred since
the last read of this register, the corresponding status bit will be set. If the corresponding enable bit in the
register is set, an interrupt will be generated if the event occurs. The PHYSCR register (0x0011) bits 1 and
0 must also be set to allow interrupts. The status indications in this register will be set even if the interrupt
is not enabled.
Table 8-20. MII Interrupt Status Register 1 (MISR1), address 0x0012
BIT
15:14
NAME
DEFAULT
RESERVED
<00>, RO
DESCRIPTION
RESERVED: Writes ignored, read as 0.
13
Link Status Changed INT
0,RO, COR
Change of Link Status interrupt:
1 = Change of link status interrupt is pending
0 = No change of link status
12
Speed Changed INT
0,RO, COR
Change of Speed Status interrupt:
1 = Change of speed status interrupt is pending
0 = No change of speed status
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
59
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
Table 8-20. MII Interrupt Status Register 1 (MISR1), address 0x0012 (continued)
BIT
DEFAULT
DESCRIPTION
11
Duplex Mode Changed INT
NAME
0,RO, COR
Change of duplex status interrupt:
1 = Duplex status change interrupt is pending
0 = No change of duplex status
10
Auto-Negotiation Completed INT
0,RO, COR
Auto-Negotiation Complete interrupt:
1 = Auto-negotiation complete interrupt is pending.
0 = No Auto-negotiation complete event is pending
9
FC HF INT
0,RO, COR
False Carrier Counter half-full interrupt:
1 = False carrier counter (Register FCSCR, address 0x0014) exceeds halffull interrupt is pending
0 = False carrier counter half-full event is not pending
8
RE HF INT
0,RO, COR
Receive Error Counter half-full interrupt:
1 = Receive error counter (Register RECR, address 0x0015) exceeds half
full interrupt is pending
0 = No Receive error counter half full event pending
7:6
RESERVED
<00>, RO
RESERVED: Writes ignored, read as 0.
5
Link Status Changed EN
0, RW
Enable Interrupt on change of link status
4
Speed Changed EN
0, RW
Enable Interrupt on change of speed status
3
Duplex Mode Changed EN
0, RW
Enable Interrupt on change of duplex status
2
Auto-Negotiation Completed EN
0, RW
Enable Interrupt on Auto-negotiation complete event
1
FC HF EN
0, RW
Enable Interrupt on False Carrier Counter Register half-full event
0
RE HF EN
0, RW
Enable Interrupt on Receive Error Counter Register half-full event
8.6
MII Interrupt Status Register 2 (MISR2)
This register contains events status and enables for the interrupt function. If an event has occurred since
the last read of this register, the corresponding status bit will be set. If the corresponding enable bit in the
register is set, an interrupt will be generated if the event occurs. The PHYSCR register (0x0011) bits 1 and
0 must also be set to allow interrupts. The status indications in this register will be set even if the interrupt
is not enabled.
Table 8-21. MII Interrupt Status Register 2 (MISR2), address 0x0013
BIT
NAME
DEFAULT
DESCRIPTION
15
RESERVED
0, RO
14
AN Error INT
0,RO, COR
Auto-Negotiation Error Interrupt:
1 = Auto-negotiation error interrupt is pending
0 = No Auto-negotiation error event pending
13
Page Rec INT
0,RO, COR
Page Receive Interrupt:
1 = Page has been received
0 = Page has not been received
12
Loopback FIFO OF/UF INT
0,RO, COR
Loopback FIFO Overflow/Underflow Event Interrupt:
1 = FIFO Overflow/Underflow event interrupt pending
0 = No FIFO Overflow/Underflow event pending
11
MDI Crossover Changed INT
0,RO, COR
MDI/MDIX Crossover Status Changed Interrupt:
1 = MDI crossover status changed interrupt is pending
0 = MDI crossover status has not changed
10
Sleep Mode INT
0,RO, COR
Sleep Mode Event Interrupt:
1 = Sleep Mode event interrupt is pending
0 = No sleep mode event pending
9
Polarity Changed INT
0,RO, COR
Polarity Changed Interrupt:
1 = Data polarity changed interrupt pending
0 = No Data polarity event pending
8
Jabber Detect INT
0,RO
Jabber Detect Event Interrupt:
1 = Jabber detect event interrupt pending
0 = No Jabber detect event pending
7
RESERVED
0,RW
RESERVED: Writes ignored, read as 0
6
AN Error EN
0,RW
Enable Interrupt on Auto-Negotiation error event
60
RESERVED: Writes ignored, read as 0.
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Table 8-21. MII Interrupt Status Register 2 (MISR2), address 0x0013 (continued)
BIT
NAME
DEFAULT
DESCRIPTION
5
Page Rec EN
0,RW
Enable Interrupt on page receive event
4
Loopback FIFO OF/UF EN
0,RW
Enable Interrupt on loopback FIFO overflow/underflow event
3
MDI Crossover Changed EN
0,RW
Enable Interrupt on change of MDI/X status
2
Sleep Mode Event EN
0,RW
Enable Interrupt sleep mode event
1
Polarity Changed EN
0,RW
Enable Interrupt on change of polarity status
0
Jabber Detect EN
0,RW
Enable Interrupt on Jabber detection event
8.7
False Carrier Sense Counter Register (FCSCR)
This counter provides information required to implement the "False Carriers" attribute within the MAU
managed object class of Clause 30 of the IEEE 802.3u specification.
Table 8-22. False Carrier Sense Counter Register (FCSCR), address 0x0014
BIT
NAME
15:8
RESERVED
7:0
FCSCNT
8.8
DEFAULT
DESCRIPTION
<0000 0000>, RO RESERVED: Writes ignored, read as 0
0,RO / COR
False Carrier Event Counter:
This 8-bit counter increments on every false carrier event. This counter stops when it
reaches its maximum count (FFh). When the counter exceeds half full (7Fh), an interrupt
event is generated. This register is cleared on read.
Receiver Error Counter Register (RECR)
This counter provides information required to implement the "Symbol Error During Carrier" attribute within
the PHY managed object class of Clause 30 of the IEEE 802.3u specification.
Table 8-23. Receiver Error Counter Register (RECR), address 0x0015
BIT
15:0
8.9
BIT NAME
RX Error Count
DEFAULT
DESCRIPTION
0, RO, / COR RX_ER Counter:
When a valid carrier is present (only while RXDV is set), and there is at least one occurrence of
an invalid data symbol, this 16-bit counter increments for each receive error detected. The
RX_ER counter does not count in MII loopback mode. The counter stops when it reaches its
maximum count of FFFFh. When the counter exceeds half-full (7FFFh), an interrupt is
generated. This register is cleared on read.
BIST Control Register (BISCR)
This register is used for Build-In Self Test (BIST) configuration. The BIST functionality provides Pseudo
Random Bit Stream (PRBS) mechanism including packet generation generator and checker. Selection of
the exact loopback point in the signal chain is also done in this register.
Table 8-24. BIST Control Register (BISCR), address 0x0016
BIT
NAME
DEFAULT
DESCRIPTION
15
RESERVED
0, RO
RESERVED: Writes ignored, read as 0
14
PRBS Count Mode
0, RW
PRBS Single/Continues Mode:
1 = Continuous mode, the PRBS counters reaches max count value, pulse is
generated and counter starts counting from zero again.
0 = Single mode, When BIST Error Counter reaches its max value, PRBS checker
stops counting.
13
Generate PRBS Packets
0, RW
Generated PRBS Packets:
1 = When packet generator is enabled, generate continuous packets with PRBS
data. When packet generator is disabled, PRBS checker is still enabled.
0 = When packet generator is enabled, generate single packet with constant data.
PRBS gen/check is disabled.
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
61
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
Table 8-24. BIST Control Register (BISCR), address 0x0016 (continued)
BIT
NAME
12
Packet Generation Enable
DEFAULT
0, RW
DESCRIPTION
Packet Generation Enable:
1 = Enable packet generation with PRBS data
0 = Disable packet generator
11
PRBS Checker Lock
0,RO
PRBS Checker Lock Indication:
1 = PRBS checker is locked and synced on received bit stream
0 = PRBS checker is not locked
10
PRBS Checker Sync Loss
0,RO,LH
PRBS Checker Sync Loss Indication:
1 = PRBS checker lose sync on received bit stream – This is an error indication
0 = PRBS checker is not locked
9
Packet Gen Status
0,RO
Packet Generator Status Indication:
1 = Packet Generator is active and generate packets
0 = Packet Generator is off
8
Power Mode
0,RO
Sleep Mode Indication:
1 = Indicate that the PHY is in normal power mode
0 = Indicate that the PHY is in one of the sleep modes, either active or passive
7
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
6
Transmit in MII Loopback
0, RW
Transmit Data in MII Loop-back Mode (valid only at 100BT):
1 = Enable transmission of the data from the MAC received on the TX pins to the
line in parallel to the MII loopback to RX pins. This bit may be set only in MII
Loopback mode – setting bit 14 in BMCR register (0x0000).
0 = Data is not transmitted to the line in MII loopback
5
4:0
RESERVED
0, RO
RESERVED: Must be 0
Loopback Mode
0, RW
Loop-back Mode Select:
The PHY provides several options for Loopback that test and verify various functional
blocks within the PHY. Enabling loopback mode allows in-circuit testing of the TLK10x
digital and analog data path
Near-end Loopback
00001 = PCS Input Loopback
00010 = PCS Output Loopback
00100 = Digital Loopback
01000 = Analog Loopback (requires 100Ω termination)
Far-end Loopback:
10000 = Reverse Loopback
8.10 RMII Control and Status Register (RCSR)
This register configures the RMII Mode of operation. When RMII mode is disabled, the RMII functionality is
bypassed.
Table 8-25. RMII Control and Status Register (RCSR), address 0x0017
NAME
DEFAULT
15:6 RESERVED
BIT
<0000 0000
00>0,RO
5
RMII Mode
0,RW, Pin_Strap
DESCRIPTION
RESERVED: Writes ignored, read as 0.
RMII Mode Enable:
1 = Enable RMII (Reduced MII) mode of operation
0 = Enable MII mode of operation
62
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Table 8-25. RMII Control and Status Register (RCSR), address 0x0017 (continued)
BIT
4
NAME
RMII Revision
Select
DEFAULT
0,RW
DESCRIPTION
RMII Revision Select:
1 = (RMII revision 1.0) CRS_DV will remain asserted until final data is transferred.
CRS_DV will not toggle at the end of a packet.
0 = (RMII revision 1.2) CRS_DV will toggle at the end of a packet to indicate deassertion of CRS.
3
RMII OVFL Status
0,COR
RX FIFO Over Flow Status:
1 = Normal
0 = Overflow detected
2
RMII OVFL Status
0,COR
RX FIFO Under Flow Status:
1 = Normal
0 = Underflow detected
1:0
ELAST_FUB
<01>,RW
Receive Elasticity Buffer Size:
This field controls the Receive Elasticity Buffer which allows for frequency variation
tolerance between the 50MHz RMII clock and the recovered data. The following values
indicate the tolerance in bits for a single packet. The minimum setting allows for standard
Ethernet frame sizes at ±50ppm accuracy for both RMII and Receive clocks. For greater
frequency tolerance the packet lengths may be scaled (for ±100ppm, divide the packet
lengths by 2).
00 = 14 bit tolerance (up to 16800 byte packets)
01 = 2 bit tolerance (up to 2400 byte packets)
10 = 6 bit tolerance (up to 7200 byte packets)
11 = 10 bit tolerance (up to 12000 byte packets)
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
63
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
8.11 LED Control Register (LEDCR)
This register provides the ability to directly manually control the Link LED output.
Table 8-26. LED Control Register (LEDCR), address 0x0018
BIT
NAME
15:11
RESERVED
10:9
Blink Rate
DEFAULT
DESCRIPTION
<0000 0>, ro
RESERVED: Writes ignored, read as 0.
<10>,RW
LED Blinking Rate (ON/OFF duration):
00 = 20Hz (50mSec)
01 = 10Hz (100mSec)
10 = 5Hz (200mSec)
11 = 2Hz (500mSec)
8
RESERVED
7
LED Link Polarity
RO
RESERVED
6
RESERVED
5
RESERVED
4
Drive Link LED
3
RESERVED
RO
RESERVED
2
RESERVED
RO
RESERVED
1
Link LED On/Off Setting
0
RESERVED
1, RW,
Pin_Strap
LED Link Polarity Setting:
1 = Active High polarity setting
0 = Active Low polarity setting
Link LED polarity defined by strapping value of this pin. This register allows
override of this strapping value.
RO
RESERVED
RO
RESERVED
0,RW
0,RW
RO
Drive LED Link to the forced On/Off setting defined in bit 1:
1 = Drive value of On/Off bit onto LED_LINK output pin
0 = Normal operation
Value to force on Link LED output
RESERVED
8.12 PHY Control Register (PHYCR)
This register provides the ability to control and set general functionality inside the PHY.
Table 8-27. PHY Control Register (PHYCR), address 0x0019
BIT
NAME
DEFAULT
15
Auto MDI/X
Enable
1, RW,
Pin_Strap
Auto-MDIX Enable:
1 = Enable Auto-negotiation Auto-MDIX capability
0 = Disable Auto- negotiation Auto-MDIX capability
14
Force MDI/X
0, RW
Force MDIX:
1 = Force MDI pairs to cross. (Receive on TPTD pair, Transmit on TPRD pair)
0 = Normal operation. (Transmit on TPTD pair, Receive on TPRD pair)
13
Pause RX
Status
0, RO
Pause Receive Negotiated Status: Indicates that pause receive should be enabled in the MAC.
Based on bits [11:10] in ANAR register and bits [11:10] in ANLPAR register settings.
This function shall be enabled according to IEEE 802.3 Annex 28B Table 28B-3, “Pause
Resolution”, only if the Auto-Negotiated Highest Common Denominator is a full duplex technology.
12
Pause TX
Status
0,RO
Pause Transmit Negotiated Status:
Indicates that pause transmit should be enabled in the MAC. Based on bits [11:10] in ANAR register
and bits [11:10] in ANLPAR register settings.
This function shall be enabled according to IEEE 802.3 Annex 28B Table 28B-3, “Pause
Resolution”, only if the Auto-Negotiated Highest Common Denominator is a full duplex technology.
11
MI Link
Status
0, RO
MII Link Status:
1 = 100BT Full-duplex Link is active and it was established using Auto-Negotiation
0 = No active link of 100BT Full-duplex, established using Auto-Negotiation
10:8
RESERVED
<000>, RO
RESERVED: Writes ignored, read as 0.
7
Bypass LED
Stretching
0, RW
Bypass LED Stretching:
1 = Bypass LED stretching
0 = Normal LED operation
Set this bit to 1 to bypass the LED stretching; the LED reflects the internal value.
6
RESERVED
RO
RESERVED
64
DESCRIPTION
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Table 8-27. PHY Control Register (PHYCR), address 0x0019 (continued)
BIT
NAME
DEFAULT
5
LED CFG
<0>, RW,
Pin_Strap
DESCRIPTION
LED Configuration Modes:
Mode
4:0
PHY ADDR
<0000 1>, RO
LED_CFG
1
1
2
0
LED_LINK
ON for Good Link
OFF for No Link
ON for Good Link
BLINK for Activity
PHY Address:
Strapping configuration for PHY Address.
8.13 10Base-T Status/Control Register (10BTSCR)
This register provides the ability to control and read status of the PHY’s internal 10Base-T functionality.
Table 8-28. 10Base-T Status/Control Register (10BTSCR), address 0x001A
NAME
DEFAULT
15:14
BIT
RESERVED
<000>, RO
RESERVED: Writes ignored, read as 0.
13
Receiver TH
0,RW
Lower Receiver Threshold Enable:
1 = Enable 10Base-T lower receiver threshold to allow operation with longer cables
0 = Normal 10Base-T operation
Squelch
<0000>,RW Squelch Configuration:
Used to set the Peak Squelch ‘ON’ threshold for the 10Base-T receiver. Every step is equal to
50mV and allow raising/lowering the Squelch threshold from 200mV to 600mV. The default
Squelch threshold is set to 200mV.
8
RESERVED
0, RO
RESERVED: Writes ignored, read as 0.
7
NLP Disable
0,RW
NLP Transmission Control:
1 = Disable transmission of NLPs
0 = Enable transmission of NLPs
6:5
RESERVED
<00>, RO
RESERVED: Writes ignored, read as 0.
Polarity Status
0,RO
10Mb Polarity Status:
1 = Inverted Polarity detected
0 = Correct Polarity detected
This bit is a duplication of bit 12 in the PHYSTS register (0x0010). Both bits will be cleared
upon a read of 10BTSCR register, but not upon a read of the PHYSTS register.
RESERVED
<000>, RO
RESERVED: Writes ignored, read as 0.
12:9
4
3:1
0
Jabber Disable 0,RW
DESCRIPTION
Jabber Disable:
1 = Jabber function disabled
0 = Jabber function enabled
Note: This function is applicable only in 10Base-T
8.14 BIST Control and Status Register 1 (BICSR1)
This register provides the total number of error bytes that was received by the PRBS checker and defines
the Inter packet Gap (IPG) for the packet generator.
Table 8-29. BIST Control and Status Register 1 (BICSR1), address 0x001B
BIT
15:8
BIT NAME
BIST Error
Count
DEFAULT
DESCRIPTION
0, RO
BIST Error Count:
Holds number of erroneous bytes that were received by the PRBS checker. Value in this
register is locked when write is done to bit[0] or bit[1] (see below).
When PRBS Count Mode set to zero, count stops on 0xFF. See BISCR register (0x0016) for
further details
Note: Writing “1” to bit 15 will lock counter’s value for successive read operation and clear the
BIST Error Counter.
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
65
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
Table 8-29. BIST Control and Status Register 1 (BICSR1), address 0x001B (continued)
BIT
7:0
BIT NAME
BIST IPG
Length
DEFAULT
DESCRIPTION
<0111 1101>,
RW
BIST IPG Length:
Inter Packet Gap (IPG) Length defines the size of the gap (in bytes) between any 2 successive
packets generated by the BIST. Default value is 0x7D which is equal to 125 bytes
8.15 BIST Control and Status Register2 (BICSR2)
This register allows programming the length of the generated packets in bytes for the BIST mechanism.
Table 8-30. BIST Control and Status Register 2 (BICSR2), address 0x001C
BIT
BIT NAME
DEFAULT
15:11
RESERVED
<0000 0>,
RO
10:0
BIST Packet
Length
0X5DC,RW
66
DESCRIPTION
RESERVED: Writes ignored, read as 0.
BIST Packet Length:
Length of the generated BIST packets. The value of this register defines the size (in bytes) of
every packet that generated by the BIST. Default value is 0x5DC which is equal to 1500 bytes
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
8.16 Cable Diagnostic Control Register (CDCR)
Table 8-31. Cable Diagnostic Control Register (CDCR), address 0x001E
BIT
NAME
DEFAULT
FUNCTION
15
Diagnostic Start
0,RW
Cable Diagnostic Process Start:
1 = Start execute cable measurement
0 = Cable Diagnostic is disabled
Diagnostic Start bit is cleared with raise of Diagnostic Done indication.
<000
00>,RO
RESERVED: Writes ignored, read as 0.
14:10 RESERVED
9:8
Link Quality
<<00>,RO
Link Quality Indication
<00> = Reserved
<01> = Good Quality Link Indication
<10> = Mid Quality Link Indication
<11> = Poor Quality Link Indication
The value of these bits are valid only when link is active – While reading “1” from “Link Status” bit
0 on PHYSTS register (0x0010).
7:4
RESERVED
0,RO
RESERVED: Writes ignored, read as 0.
3:2
RESERVED
00>,RO
RESERVED: Writes ignored, read as 0.
1
Diagnostic Done 0,RO
Cable Diagnostic Process Done:
1 = Indication that cable measurement process completed
0 = Diagnostic has not completed
0
Diagnostic Fail
Cable Diagnostic Process Fail:
1 = Indication that cable measurement process failed
0 = Diagnostic has not failed
0,RO
8.17 PHY Reset Control Register (PHYRCR)
This register provides ability to the system to reset or restart the PHY by register access.
Table 8-32. PHY Reset Control Register (PHYRCR), address 0x001F
BIT
NAME
DEFAULT
FUNCTION
15
Software Reset
0, RW,SC
Software Reset:
1 = Reset PHY. Allow the system to reset the PHY using register access. This bit is self cleared
and has same effect as Hardware reset pin.
0 = Normal Operation
14
Software
Restart
0, RW,SC
Software Restart:
1 = Reset PHY. Allow the system to restart the PHY using register access. This bit is self
cleared and resets all PHY circuitry except the registers.
0 = Normal Operation
<00 0000 0000
0000>, RO
Writes ignored, read as 0
13:0 RESERVED
8.18 TX_CLK Phase Shift Register (TXCPSR)
This register allows programming the phase of the MII transmit clock (TX_CLK pin). The TX_CLK has a
fixed phase to the XI pin. However the default phase, while fixed, may not be ideal for all systems,
therefore this register may be used by the system to align the reference clock (XI pin) to the TX_CLK. The
phase shift value is in 4ns units. The phase shift value should be between 0 and 10 (0ns to 40ns). If value
greater than 10 is written, the update value will be the written value modulo 10.
Table 8-33. TX_CLK Phase Shift Register (TXCPSR), address 0x0042
BIT
NAME
DEFAULT
15:5 RESERVED <0000 0000
000>, RO
4
Phase Shift
Enable
0,RW,SC
FUNCTION
RESERVED: Writes ignored, read as 0
TX Clock Phase Shift Enable:
1 = Perform Phase Shift to the TX_CLK according to the value written to Phase Shift Value in bits
[4:0].
0 = No change in TX Clock phase
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
67
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
Table 8-33. TX_CLK Phase Shift Register (TXCPSR), address 0x0042 (continued)
BIT
NAME
DEFAULT
FUNCTION
3:0
Phase Shift
Value
<0000>,RW
TX Clock Phase Shift Value:
The value of this register represents the current phase shift between Reference clock at XI and MII
Transmit Clock at TX_CLK. Any different value that will be written to these bits will shift TX_CLK by 4
times the difference (in nSec).
For example, if the value of this register is 0x2, Writing 0x9 to this register shifts TX_CLK by 28nS (4
times 7).However, since the maximum difference between XI and TX_CLK could be 40nSec (value of
10) in case of writing value bigger than 10, the updated value is the written value modulo 10.
8.19 Voltage Regulator Control Register (VRCR)
This register gives the host processor the ability to power down the voltage-regulator block of the PHY via
register access. This power-down operation is available in systems operating with an external power
supply.
Table 8-34. Voltage Regulator Control Register (VRCR), address 0x00D0
BIT
NAME
DEFAULT
FUNCTION
15
VRPD
0, RW, SC
Voltage Regulator Power Down:
1 = Power Down. Allow the system to power down the voltage regulator block of the PHY
using register access.
0 = Normal Operation. Voltage Regulator is powered and outputs voltage on the PFBOUT
pin.
14:4
RESERVED
<000 0000 0000>,
RW
RESERVED: Must be written as 0.
3:0
VR Control
<0000>, RW
Voltage Regulator Control This value should be ignored on read. To write to this register,
perform a read followed by a write with the desired value.
8.20 Cable Diagnostic Configuration/Result Registers (TLK106)
8.20.1 ALCD Control and Results 1 (ALCDRR1)
Table 8-35. ALCD Control and Results 1 (ALCDRR1), address 0x0155
BIT
15
BIT NAME
alcd_start
14:13
DEFAULT
<0>, SC
RESERVED: Writes ignored, read as 0.
TPTD Diagnostic Bypass
1 = Bypass TPTD diagnostic. TDR on TPTD pair is not executed.
0 = TDR is executed on TPTD pair
alcd_done
<0>, RO
11:4
alcd_out1
<0000
0000>, RO
3
RESERVED
alcd_ctrl
1 = Start ALCD
<00>, RO
12
2:0
DESCRIPTION
<0>, RO
<001>,RW
alcd_out1
RESERVED: Writes ignored, read as 0
Control of ALCD Average factor
8.20.2 Cable Diagnostic Specific Control Registers (CDSCR1 - CDSCR4)
Use CDSCR1 to select the channel for the cable diagnostics test. CDSCR1 contains the enable and
bypass bits for the diagnostic tests, and defines the number of executed and averaged TDR sequences.
CDSCR2 - CDSCR4 configure other parameters for cable diagnostics.
Table 8-36. Cable Diagnostic Specific Control Register (CDSCR), address 0x0170
BIT
15
68
BIT NAME
RESERVED
DEFAULT
0,RO
DESCRIPTION
RESERVED: Writes ignored, read as 0.
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Table 8-36. Cable Diagnostic Specific Control Register (CDSCR), address 0x0170 (continued)
BIT
BIT NAME
DEFAULT
DESCRIPTION
14
Diagnostic Cross
Disable
0,RW
Cross TDR Diagnostic mode
1 = Disable TDR Cross mode – TDR will be executed in regular mode only
0 = Diagnostic of crossing pairs is enabled In Cross Diagnostic mode, the TDR mechanism
is looking for reflection on the other pair to check short between pairs.
13
Diagnostic TPTD
Bypass
0,RW
TPTD Diagnostic Bypass
1 = Bypass TPTD diagnostic. TDR on TPTD pair will not be executed.
0 = TDR is executed on TPTD pair
In bypass TPTD, results are available in TPRD slots.
12
Diagnostic TPRD
Bypass
0,RO
TPRD Diagnostic Bypass
1 = Bypass TPRD diagnostic. TDR on TPRD pair will not be executed.
0 = TDR is executed on TPRD pair
11
RESERVED
1,RW
RESERVED: Must be Set to 1.
10:8
Diagnostics Average
Cycles
7:0
RESERVED
<110>,RW
0,RO
Number Of TDR Cycles to Average:
<000>: 1 TDR cycle
<001>: 2 TDR cycles
<010>: 4 TDR cycles
<011>: 8 TDR cycles
<100>: 16 TDR cycles
<101>: 32 TDR cycles
<110>: 64 TDR cycles (default)
<111>: Reserved
RESERVED: Writes ignored, read as 0.
Table 8-37. Cable Diagnostic Specific Control Register 2 (CDSCR2), address 0x0171
BIT
BIT NAME
15:4
RESERVED
3:0
TDR pulse control
DEFAULT
DESCRIPTION
<1100 1000 RESERVED: Ignore on read
0101>, RW
<0001>,
RW
Configure expected self reflection in TDR
Table 8-38. Cable Diagnostic Specific Control Register 3 (CDSCR3), address 0x0173
BIT
BIT NAME
DEFAULT
DESCRIPTION
15:8
Cable length cfg
<1010
0000>, RW
Configure duration of listening to detect long cable reflections
7:0
RESERVED
<0001
1110>, RW
RESERVED: Ignore on read
Table 8-39. Cable Diagnostic Specific Control Register 4 (CDSCR4), address 0x0177
BIT
BIT NAME
DEFAULT
DESCRIPTION
15:13
RESERVED
<000>, RW
RESERVED: Ignore on read
12:8
Short cables TH
<0 1101>,
RW
TH to compensate for strong reflections in short cables
7:0
RESERVED
<1001
0110>, RW
RESERVED: Ignore on read
8.20.3 Cable Diagnostic Location Results Register 1 (CDLRR1)
This register provides the peaks locations after execution of the TDR. The values of this register are valid
after reading 1 in Diagnostic Done bit 1 in register CDCR (0x1E).
Table 8-40. Cable Diagnostic Location Results Register 1 (CDLRR1), address 0x0180
BIT
NAME
15:8 TPTD Peak
Location 2
DEFAULT
FUNCTION
<0000 0000>, RO
Location of the Second peak discovered by the TDR mechanism on Transmit Channel
(TPTD). The value of these bits is translated into distance from the PHY
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
69
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
Table 8-40. Cable Diagnostic Location Results Register 1 (CDLRR1), address 0x0180 (continued)
BIT
NAME
DEFAULT
FUNCTION
7:0
TPTD Peak
Location 1
<0000 0000>, RO
Location of the First peak discovered by the TDR mechanism on Transmit Channel
(TPTD). The value of these bits is translated into distance from the PHY
8.20.4 Cable Diagnostic Location Results Register 2 (CDLRR2)
This register provides the peaks locations after execution of the TDR. The values of this register are valid
after reading 1 in Diagnostic Done bit 1 in register CDCR (0x1E).
Table 8-41. Cable Diagnostic Location Results Register 2 (CDLRR2), address 0x0181
DEFAULT
FUNCTION
15:8 TPTD Peak
Location 4
BIT
NAME
<0000 0000>, RO
Location of the Fourth peak discovered by the TDR mechanism on Transmit Channel
(TPTD). The value of these bits is translated into distance from the PHY.
7:0
<0000 0000>, RO
Location of the Third peak discovered by the TDR mechanism on Transmit Channel
(TPTD). The value of these bits is translated into distance from the PHY.
TPTD Peak
Location 3
8.20.5 Cable Diagnostic Location Results Register 3 (DDLRR3)
This register provides the peaks locations after execution of the TDR. The values of this register are valid
after reading 1 in Diagnostic Done bit 1 in register CDCR (0x1E).
Table 8-42. Cable Diagnostic Location Results Register 3 (DDLRR3), address 0x0182
DEFAULT
FUNCTION
15:8 TPRD Peak
Location 1
BIT
NAME
<0000 0000>, RO
Location of the First peak discovered by the TDR mechanism on Receive Channel
(TPRD). The value of these bits is translated into distance from the PHY.
7:0
<0000 0000>, RO
Location of the Fifth peak discovered by the TDR mechanism on Transmit Channel
(TPTD). The value of these bits is translated into distance from the PHY.
TPTD Peak
Location 5
8.20.6 Cable Diagnostic Location Results Register 4 (CDLRR4)
This register provides the peaks locations after execution of the TDR. The values of this register are valid
after reading 1 in Diagnostic Done bit 1 in register CDCR (0x1E).
Table 8-43. Cable Diagnostic Location Results Register 4 (CDLRR4), address 0x0183
BIT
NAME
DEFAULT
FUNCTION
15:8 TPRD Peak
Location 3
<0000 0000>, RO
Location of the Third peak discovered by the TDR mechanism on Receive Channel
(TPRD). The value of these bits is translated into distance from the PHY.
7:0
<0000 0000>, RO
Location of the Second peak discovered by the TDR mechanism on Receive Channel
(TPRD). The value of these bits is translated into distance from the PHY.
TPRD Peak
Location 2
8.20.7 Cable Diagnostic Location Results Register 5 (CDLRR5)
This register provides the peaks locations after execution of the TDR. The values of this register are valid
after reading 1 in Diagnostic Done bit 1 in register CDCR (0x1E).
Table 8-44. Cable Diagnostic Location Results Register 5 (CDLRR5), address 0x0184
DEFAULT
FUNCTION
15:8 TPRD Peak
Location 5
BIT
<0000 0000>, RO
Location of the Fifth peak discovered by the TDR mechanism on Receive Channel
(TPRD). The value of these bits is translated into distance from the PHY.
7:0
<0000 0000>, RO
Location of the Fourth peak discovered by the TDR mechanism on Receive Channel
(TPRD). The value of these bits is translated into distance from the PHY.
70
NAME
TPRD Peak
Location 4
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
8.20.8 Cable Diagnostic Amplitude Results Register 1 (CDARR1)
This register provides the peaks amplitude measurement after the execution of the TDR. The values of
this register are valid after reading 1 in Diagnostic Done bit 1 in register CDCR (0x1E).
Table 8-45. Cable Diagnostic Amplitude Results Register 1 (CDARR1), address 0x0185
BIT
NAME
DEFAULT
FUNCTION
15
RESERVED
0,RO
RESERVED: Writes ignored, read as 0.
<000 0000>,RO
Amplitude of the Second peak discovered by the TDR mechanism on Transmit Channel
(TPTD). The value of these bits is translated into type of cable fault and-or interference.
This amplitude value refers to peak location stored in bits [15:8] in register CDLRR1 (0x180)
14:8 TPTD Peak
Amplitude 2
7
RESERVED
0,RO
RESERVED: Writes ignored, read as 0.
6:0
TPTD Peak
Amplitude 1
<000 0000>,RO
Amplitude of the First peak discovered by the TDR mechanism on Transmit Channel (TPTD).
The value of these bits is translated into type of cable fault and-or interference.
This amplitude value refers to peak location stored in bits [7:0] in register CDLRR1 (0x180)
8.20.9 Cable Diagnostic Amplitude Results Register 2 (CDARR2)
This register provides the peaks amplitude measurement after the execution of the TDR. The values of
this register are valid after reading 1 in Diagnostic Done bit 1 in register CDCR (0x1E).
Table 8-46. Cable Diagnostic Amplitude Results Register 2 (CDARR2), address 0x0186
BIT
NAME
DEFAULT
FUNCTION
15
RESERVED
0,RO
RESERVED: Writes ignored, read as 0.
<000 0000>,RO
Amplitude of the Fourth peak discovered by the TDR mechanism on Transmit Channel
(TPTD). The value of these bits is translated into type of cable fault and-or interference.
This amplitude value refers to peak location stored in bits [15:8] in register CDLRR2 (0x181)
14:8 TPTD Peak
Amplitude 4
7
RESERVED
0,RO
RESERVED: Writes ignored, read as 0.
6:0
TPTD Peak
Amplitude 3
<000 0000>,RO
Amplitude of the Third peak discovered by the TDR mechanism on Transmit Channel
(TPTD). The value of these bits is translated into type of cable fault and-or interference.
This amplitude value refers to peak location stored in bits [7:0] in register CDLRR2 (0x181)
8.20.10 Cable Diagnostic Amplitude Results Register 3 (CDARR3)
This register provides the peaks amplitude measurement after the execution of the TDR. The values of
this register are valid after reading 1 in Diagnostic Done bit 1 in register CDCR (0x1E).
Table 8-47. Cable Diagnostic Amplitude Results Register 3 (CDARR3), address 0x0187
BIT
NAME
DEFAULT
FUNCTION
15
RESERVED
0,RO
RESERVED: Writes ignored, read as 0.
<000 0000>,RO
Amplitude of the First peak discovered by the TDR mechanism on Receive Channel (TPRD).
The value of these bits is translated into type of cable fault and-or interference.
This amplitude value refers to peak location stored in bits [15:8] in register CDLRR3 (0x182)
14:8 TPRD Peak
Amplitude 1
7
RESERVED
0,RO
RESERVED: Writes ignored, read as 0.
6:0
TPTD Peak
Amplitude 5
<000 0000>,RO
Amplitude of the Fifth peak discovered by the TDR mechanism on Transmit Channel (TPTD).
The value of these bits is translated into type of cable fault and-or interference.
This amplitude value refers to peak location stored in bits [7:0] in register CDLRR3 (0x182)
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
71
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
8.20.11 Cable Diagnostic Amplitude Results Register 4 (CDARR4)
This register provides the peaks amplitude measurement after the execution of the TDR. The values of
this register are valid after reading 1 in Diagnostic Done bit 1 in register CDCR (0x1E).
Table 8-48. Cable Diagnostic Amplitude Results Register 4 (CDARR4), address 0x0188
BIT
NAME
DEFAULT
FUNCTION
15
RESERVED
0,RO
RESERVED: Writes ignored, read as 0.
<000
0000>,RO
Amplitude of the Third peak discovered by the TDR mechanism on Receive Channel (TPRD).
The value of these bits is translated into type of cable fault and-or interference.
This amplitude value refers to peak location stored in bits [15:8] in register CDLRR4 (0x183)
14:8 TPRD Peak
Amplitude 3
7
RESERVED
0,RO
RESERVED: Writes ignored, read as 0.
6:0
TPRD Peak
Amplitude 2
<000
0000>,RO
Amplitude of the Second peak discovered by the TDR mechanism on Receive Channel
(TPRD). The value of these bits is translated into type of cable fault and-or interference.
This amplitude value refers to peak location stored in bits [7:0] in register CDLRR4 (0x183)
8.20.12 Cable Diagnostic Amplitude Results Register 5 (CDARR5)
This register provides the peaks amplitude measurement after the execution of the TDR. The values of
this register are valid after reading 1 in Diagnostic Done bit 1 in register CDCR (0x1E).
Table 8-49. Cable Diagnostic Amplitude Results Register 5 (CDARR5), address 0x0189
BIT
NAME
DEFAULT
FUNCTION
15
RESERVED
0,RO
RESERVED: Writes ignored, read as 0.
<000
0000>,RO
Amplitude of the Fifth peak discovered by the TDR mechanism on Receive Channel (TPRD).
The value of these bits is translated into type of cable fault and-or interference.
This amplitude value refers to peak location stored in bits [15:8] in register CDLRR4 (0x184)
14:8 TPRD Peak
Amplitude 5
7
RESERVED
0,RO
RESERVED: Writes ignored, read as 0.
6:0
TPRD Peak
Amplitude 4
<000
0000>,RO
Amplitude of the Fourth peak discovered by the TDR mechanism on Receive Channel
(TPRD). The value of these bits is translated into type of cable fault and-or interference.
This amplitude value refers to peak location stored in bits [7:0] in register CDLRR4 (0x184)
8.20.13 Cable Diagnostic General Results Register (CDGRR)
This register provides general measurement results after the execution of the TDR. The Cable Diagnostic
software should post process this result together with other Peaks’ location and amplitude results.
Table 8-50. Cable Diagnostic General Results Register (CDGRR), address 0x018A
BIT
NAME
DEFAULT
FUNCTION
15
TPTD Peak Polarity 5
0,RO
Polarity of the Fifth peak discovered by the TDR mechanism on Transmit Channel (TPTD)
14
TPTD Peak Polarity 4
0,RO
Polarity of the Fourth peak discovered by the TDR mechanism on Transmit Channel
(TPTD)
13
TPTD Peak Polarity 3
0,RO
Polarity of the Third peak discovered by the TDR mechanism on Transmit Channel (TPTD)
12
TPTD Peak Polarity 2
0,RO
Polarity of the Second peak discovered by the TDR mechanism on Transmit Channel
(TPTD)
11
TPTD Peak Polarity 1
0,RO
Polarity of the First peak discovered by the TDR mechanism on Transmit Channel (TPTD)
10
TPRD Peak Polarity 5
0,RO
Polarity of the Fifth peak discovered by the TDR mechanism on Receive Channel (TPRD)
9
TPRD Peak Polarity 4
0,RO
Polarity of the Fourth peak discovered by the TDR mechanism on Receive Channel
(TPRD)
8
TPRD Peak Polarity 3
0,RO
Polarity of the Third peak discovered by the TDR mechanism on Receive Channel (TPRD)
7
TPRD Peak Polarity 2
0,RO
Polarity of the Second peak discovered by the TDR mechanism on Receive Channel
(TPRD)
6
TPRD Peak Polarity 1
0,RO
Polarity of the First peak discovered by the TDR mechanism on Receive Channel (TPRD)
5
Cross Detect on TPTD
0,RO
Cross Reflection were detected on TPTD. Indicate on Short between TPTD and TPRD
4
Cross Detect on TPRD 0,RO
Cross Reflection were detected on TPRD. Indicate on Short between TPTD and TPRD
72
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
Table 8-50. Cable Diagnostic General Results Register (CDGRR), address 0x018A (continued)
BIT
NAME
DEFAULT
FUNCTION
3
Above 5 TPTD Peaks
0,RO
More than 5 reflections were detected on TPTD
2
Above 5 TPRD Peaks
0,RO
More than 5 reflections were detected on TPRD
RESERVED
<00>,RO
RESERVED: Writes ignored, read as 0
1:0
8.20.14 ALCD Control and Results 2 (ALCDRR2)
Table 8-51. ALCD Control and Results 2 (ALCDRR2), address 0x0215
BIT
BIT NAME
DEFAULT
DESCRIPTION
15:12
alcd_out2
<0011>, SC alcd_out2
11:0
alcd_out3
<0110 0000 alcd_out3
0000>, RW
Register Block
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
73
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
9 Electrical Specifications
All parameters are derived by test, statistical analysis, or design.
ABSOLUTE MAXIMUM RATINGS (1)
9.1
VDD33_IO, AVDD33
Supply voltage
PFBIN1, PFBIN2
DC Input voltage
–0.3 to 3.8
XO
DC Output voltage
–0.3 to 3.8
Other outputs
V
–0.3 to 3.8
TJ
Maximum die temperature
125
°C
±4
kV
(2)
Human-Body
Model
All pins
Ethernet network pins (TD+, TD-, RD+, RD-) (3)
±16
Charged-Device
Model
All pins (4)
±750
ESD
V
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating
conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Tested in accordance to JEDEC Standard 22, Test Method A114.
Test method based upon JEDEC Standard 22 Test Method A114, Ethernet network pins (TD+, TD-, RD+, RD-) pins stressed with
respect to GND.
Tested in accordance to JEDEC Standard 22, Test Method C101.
9.2
RECOMMENDED OPERATING CONDITIONS
VDD33_IO, AVDD33 I/O and Analog 3.3V Supply
PFBIN1, PFBIN2
Core Supply voltage
TA
Ambient
temperature (1)
MIN
NOM
MAX
3.0
3.3
3.6
V
1.47
1.55
1.62
V
TLK105
–40
85
TLK106
–40
105
Power dissipation (2)
PD
(1)
(2)
V
–0.3 to 6
Other Inputs
(4)
V
–0.3 to 3.8
TD-, TD+, RD-, RD+
(2)
(3)
UNIT
–0.3 to 1.8
XI
(1)
VALUE
–0.3 to 3.8
270
UNIT
°C
mW
Provided that DOWN_PAD, pin 33, is soldered down. See Thermal Vias Recommendation for more detail.
For 100Base-TX, When internal 1.55V is used. Device is operated from single 3.3V supply only.
9.3
9.3.1
THERMAL CHARACTERISTICS
TLK105 32-Pin Industrial Device (85°C) Thermal Characteristics
over operating free-air temperature range (unless otherwise noted)
PARAMETER
CONDITIONS
θJA
Junction-to-ambient thermal resistance (no airflow)
θJB
Junction-to-board thermal resistance
θJC(Top)
Junction-to-case thermal resistance, Top
θJC(Bottom)
Junction-to-case thermal resistance, Bottom
9.3.2
74
JEDEC high-K model
MIN
TYP
MAX
UNIT
36.4
9.3
26.8
°C/W
1.7
TLK106 32-Pin Extended Temperature (105°C) Device Thermal Characteristics
Electrical Specifications
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
over operating free-air temperature range (unless otherwise noted)
PARAMETER
CONDITIONS
θJA
Junction-to-ambient thermal resistance (no airflow)
θJB
Junction-to-board thermal resistance
θJC(Top)
Junction-to-case thermal resistance, Top
θJC(Bottom)
Junction-to-case thermal resistance, Bottom
9.4
MIN
TYP
JEDEC high-K model
MAX
UNIT
36.4
9.3
°C/W
26.8
1.7
DC CHARACTERISTICS
over operating free-air temperature range (unless otherwise noted)
PARAMETER
VIH
Input high voltage
VIL
Input low voltage
IIH
Input high current
IIL
Input low current
VOL
(1)
TEST CONDITIONS
Nominal VCC = VDD33_IO = 3.3V
MIN
TYP
MAX
UNIT
2.0
V
(1)
0.8
V
VIN = VCC
10
μA
VIN = GND
10
μA
Output low voltage
IOL = 4 mA
0.4
V
VOH
Output high voltage
IOH = –4 mA
IOZ
3-State leakage
VOUT = VCC, VOUT = GND
±10
μA
RPULLUP
Integrated Pullup Resistance
14.7
23.7
49.7
kΩ
RPULLDOWN
Integrated Pulldown Resistance
14.5
24.9
48.1
kΩ
VTPTD_100
100M transmit voltage
0.95
1
1.05
V
VTPTDsym
100M transmit voltage symmetry
VTPTD_10
10M transmit voltage
CIN1
CMOS input capacitance
5
COUT1
CMOS output capacitance
5
pF
VTH1
10Base-T Receive threshold
200
mV
(1)
VCC – 0.5
V
±2%
2.2
2.5
2.8
V
pF
Nominal VCC of VDD33_IO = 3.3V
Electrical Specifications
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
75
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
9.5
www.ti.com
POWER SUPPLY CHARACTERISTICS
The data was measured using a TLK10x evaluation board. The current from each of the power supplies is
measured and the power dissipation is computed. For the single 3.3V external supply case the power dissipation
across the internal linear regulator is also included. All the power dissipation numbers are measured at the
nominal power supply and typical temperature of 25°C. The power needed is given both for the device only, and
including the center tap of the transformer for a total system power requirement. The center tap of the
transformer is normally connected to the 3.3V supply, thus the current needed may also be easily calculated.
9.5.1
Active Power
PARAMETER
TEST CONDITIONS
FROM POWER PINS
FROM
TRANSFORMER
CENTER TAP
UNIT
100Base-TX /W Traffic (full packet 1518B
rate)
Single 3.3V external supply
203
73
mW
10Base-T /W Traffic (full packet 1518B rate)
Single 3.3V external supply
96
211
mW
9.5.2
Power-Down Power
TEST CONDITIONS (1)
FROM THE POWER SUPPLIES
FROM TRANSFORMER
CENTER TAP
UNIT
IEEE PWDN
Single 3.3V external supply
12
5
mW
Passive Sleep Mode
Single 3.3V external supply
71
5
mW
Active Sleep Mode
Single 3.3V external supply
71
5
mW
PARAMETER
(1)
76
Measured under typical conditions.
Electrical Specifications
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
9.6
9.6.1
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
AC Specifications
Power Up Timing
Table 9-1. Power Up Timing
PARAMETER
t1
TEST CONDITIONS
Time from powerup to hardware-configuration pin
transition to output-driver function, using internal
POR (RESET pin tied high)
MIN
TYP MAX
100
270
UNIT
ms
VDD
Hardware RESET
t1
Dual function pins
Become enabled
As outputs
Figure 9-1. Power Up Timing
NOTE
It is important to choose pullup and-or pulldown resistors for each of the hardware
configuration pins that provide fast RC time constants in order to latch in the proper value
prior to the pin transitioning to an output driver.
9.6.2
Reset Timing
Table 9-2. Reset Timing
PARAMETER
t1
TEST CONDITIONS
XI Clock must be stable for minimum of 1ms
during RESET pulse low time.
RESET pulse width
MIN
TYP MAX
1
UNIT
µs
VCC
XI Clock
t1
Hardware
RESET
T0339-01
Figure 9-2. Reset Timing
Electrical Specifications
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
77
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
9.6.3
www.ti.com
MII Serial Management Timing
Table 9-3. MII Serial Management Timing
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
2.5
25
MHz
30
ns
t1
MDC Frequency
t2
MDC to MDIO (Output) Delay Time
t3
MDIO (Input) to MDC Hold Time
10
ns
t4
MDIO (Input) to MDC Setup Time
10
ns
0
MDC
t1
t2
MDIO (Output)
MDC
t3
t4
MDIO (Input)
Valid Data
T0340-01
Figure 9-3. MII Serial Management Timing
9.6.4
100Mb/s MII Transmit Timing
Table 9-4. 100Mb/s MII Transmit Timing
PARAMETER
MIN
TYP
MAX
100Mbs Normal mode
16
20
24
TXD[3:0], TX_EN Data Setup to TX_CLK
100Mbs Normal mode
10
ns
TXD[3:0], TX_EN Data Hold from TX_CLK
100Mbs Normal mode
0
ns
t1
TX_CLK High Time
t2
TX_CLK Low Time
t3
t4
TEST CONDITIONS
UNIT
ns
t2
t1
TX_CLK
t3
t4
TXD[3:0]
TX_EN
Valid Data
T0341-01
Figure 9-4. 100Mb/s MII Transmit Timing
78
Electrical Specifications
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
9.6.5
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
100Mb/s MII Receive Timing
Table 9-5. 100Mb/s MII Receive Timing
PARAMETER
(1)
TEST CONDITIONS
t1
RX_CLK High Time
t2
RX_CLK Low Time
t3
RX_CLK to RXD[3:0], RX_DV, RX_ER Delay
(1)
MIN
TYP
MAX
UNIT
100Mbs Normal mode
16
20
24
ns
100Mbs Normal mode
10
30
ns
RX_CLK may be held low or high for a longer period of time during transition between reference and recovered clocks. Minimum high
and low times will not be violated.
t1
t2
RX_CLK
t3
RXD[3:0]
RX_DV
RX_ER
Valid Data
T0342-01
Figure 9-5. 100Mb/s MII Receive Timing
9.6.6
100Base-TX Transmit Packet Latency Timing
Table 9-6. 100Base-TX Transmit Packet Latency Timing
PARAMETER
t1
(1)
(2)
TEST CONDITIONS
MIN
100Mbs Normal mode (1)
TX_CLK to PMD Output Pair Latency
TYP
4.8
MAX
UNIT
bits (2)
For Normal mode, latency is determined by measuring the time from the first rising edge of TX_CLK occurring after the assertion of
TX_EN to the first bit of the 'J' code group as output from the PMD Output Pair. 1 bit time = 10ns in 100Mbs mode.
1 bit time is equal 10 nS in 100 Mb/s mode.
TX_CLK
TX_EN
TXD
t1
PMD Output Pair
IDLE
(J/K)
DATA
T0343-01
Figure 9-6. 100Base-TX Transmit Packet Latency Timing
Electrical Specifications
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
79
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
9.6.7
www.ti.com
100Base-TX Transmit Packet Deassertion Timing
Table 9-7. 100Base-TX Transmit Packet Deassertion Timing
PARAMETER
t1
TEST CONDITIONS
TX_CLK to PMD Output Pair deassertion
MIN
100Mbs Normal mode
TYP
4.6
MAX
UNIT
bits
TX_CLK
TX_EN
TXD
t1
PMD Output Pair
DATA
DATA
(T/R)
(T/R)
IDLE
IDLE
T0344-01
Figure 9-7. 100Base-TX Transmit Packet Deassertion Timing
80
Electrical Specifications
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
9.6.8
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
100Base-TX Transmit Timing (tR/F and Jitter)
Table 9-8. 100Base-TX Transmit Timing (tR/F and Jitter)
PARAMETER
t1
t2
(1)
(2)
TEST CONDITIONS
MIN
TYP
MAX
3
4
5
ns
100Mbs tR and tF Mismatch (2)
500
ps
100Mbs PMD Output Pair Transmit Jitter
1.4
ns
100Mbs PMD Output Pair tR and tF
(1)
UNIT
Rise and fall times taken at 10% and 90% of the +1 or -1 amplitude.
Normal Mismatch is the difference between the maximum and minimum of all rise and fall times.
t1
+1 rise
90%
10%
PMD Output Pair
10%
90%
+1 fall
t1
–1 rise
t1
–1 fall
t1
t2
PMD Output Pair
Eye Pattern
t2
T0345-01
Figure 9-8. 100Base-TX Transmit Timing (tR/F and Jitter)
Electrical Specifications
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
81
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
9.6.9
www.ti.com
100Base-TX Receive Packet Latency Timing
Table 9-9. 100Base-TX Receive Packet Latency Timing
TEST CONDITIONS (1)
PARAMETER
(3)
MIN
TYP
MAX UNIT (2)
t1
Carrier Sense ON Delay
100Mbs Normal mode
14
bits
t2
Receive Data Latency
100Mbs Normal mode
19
bits
Receive data latency (4)
100Mb normal mode with fast RXDV
detection ON
15
bits
t2
(1)
(2)
(3)
(4)
PMD Input Pair voltage amplitude is greater than the Signal Detect Turn-On Threshold Value.
1 bit time = 10 ns in 100Mbs mode
Carrier Sense On Delay is determined by measuring the time from the first bit of the “J” code group to the assertion of Carrier Sense.
Fast RXDV detection could be enabled by setting bit[1] of CR1 (address 0x0009).
PMD Input Pair
IDLE
(J/K)
Data
t1
CRS
t2
RXD[3:0]
RX_DV
RX_ER
T0346-01
Figure 9-9. 100Base-TX Receive Packet Latency Timing
9.6.10 100Base-TX Receive Packet Deassertion Timing
Table 9-10. 100Base-TX Receive Packet Deassertion Timing
PARAMETER
t1
(1)
(2)
TEST CONDITIONS
Carrier Sense OFF Delay (1)
MIN
100Mbs Normal mode
TYP
19
MAX
UNIT
bits (2)
Carrier Sense Off Delay is determined by measuring the time from the first bit of the “T” code group to the deassertion of Carrier Sense.
1 bit time = 10 ns in 100Mbs mode
PMD Input Pair
DATA
(T/R)
IDLE
t1
CRS
T0347-01
Figure 9-10. 100Base-TX Receive Packet Deassertion Timing
82
Electrical Specifications
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
9.6.11 10Mbs MII Transmit Timing
Table 9-11. 10Mbs MII Transmit Timing
PARAMETER
MIN
TYP
MAX
UNIT
10Mbs MII mode
190
200
210
ns
TXD[3:0], TX_EN Data Setup to TX_CLK ↑
10Mbs MII mode
25
ns
TXD[3:0], TX_EN Data Hold from TX_CLK ↑
10Mbs MII mode
0
ns
t1
TX_CLK Low Time
t2
TX_CLK High Time
t3
t4
TEST CONDITIONS
An attached Mac should drive the transmit signals using the positive edge of TX_CLK. As shown in
Figure 9-11, the MII signals are sampled on the falling edge of TX_CLK.
t2
t1
TX_CLK
t4
t3
TXD[3:0]
TX_EN
Valid Data
Figure 9-11. 10Mbs MII Transmit Timing
9.6.12 10Mb/s MII Receive Timing
Table 9-12. 10Mb/s MII Receive Timing
PARAMETER (1)
TEST CONDITIONS
MIN
TYP
MAX
UNIT
160
200
240
ns
t1
RX_CLK High Time
t2
RX_CLK Low Time
t3
RX_CLK rising edge delay from RXD[3:0], RX_DV Valid
10Mbs MII mode
100
ns
RX_CLK to RXD[3:0], RX_DV Delay
10Mbs MII mode
100
ns
t4
(1)
RX_CLK may be held low for a longer period of time during transition between reference and recovered clocks. Minimum high and low
times will not be violated.
t1
t2
RX_CLK
t3
t4
RXD[3:0]
RX_DV
Valid Data
T0349-01
Figure 9-12. 10Mb/s MII Receive Timing
Electrical Specifications
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
83
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
9.6.13 10Base-T Transmit Timing (Start of Packet)
Table 9-13. 10Base-T Transmit Timing (Start of Packet)
PARAMETER
t1
(1)
TEST CONDITIONS
Transmit Output Delay from the Falling Edge of TX_CLK
MIN
10Mbs MII mode
TYP
MAX
5.8
UNIT (1)
bits
(1) 1 bit time = 100ns in 10Mb/s.
TX_CLK
TX_EN
TXD
t1
PMD Output Pair
Figure 9-13. 10Base-T Transmit Timing (Start of Packet)
9.6.14 10Base-T Transmit Timing (End of Packet)
Table 9-14. 10Base-T Transmit Timing (End of Packet)
MIN
TYP
t1
End of Packet High Time (with ‘0’ ending bit)
PARAMETER
TEST CONDITIONS
250
310
MAX
UNIT
ns
t2
End of Packet High Time (with ‘1’ ending bit)
250
310
ns
TX_CLK
TX_EN
t1
0
PMD Output Pair
PMD Output Pair
1
0
1
t2
Figure 9-14. 10Base-T Transmit Timing (End of Packet)
84
Electrical Specifications
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
9.6.15 10Base-T Receive Timing (Start of Packet)
Table 9-15. 10Base-T Receive Timing (Start of Packet)
PARAMETER
TEST CONDITIONS
t1
Carrier Sense Turn On Delay (PMD Input Pair to CRS)
t2
RX_DV Latency (1)
t3
Receive Data Latency
(1)
MIN
Measurement shown from
SFD
TYP
MAX
550
1000
UNIT
ns
14
bits
14
bits
10Base-T RX_DV Latency is measured from first bit of decoded SFD on the wire to the assertion of RX_DV
1st SFD Bit Decoded
1
0
1
0
1
0
1
0
1
0
1
1
TPRD
t1
CRS
RX_CLK
t2
RX_DV
t3
RXD[3:0]
0000
Preamble
SFD
Data
Figure 9-15. 10Base-T Receive Timing (Start of Packet)
9.6.16 10Base-T Receive Timing (End of Packet)
Table 9-16. 10Base-T Receive Timing (End of Packet)
PARAMETER
t1
TEST CONDITIONS
MIN
Carrier Sense Turn Off Delay
TYP
MAX
1.8
1
0
1
UNIT
μs
IDLE
PMD Input Pair
RX_CLK
t1
CRS
Figure 9-16. 10Base-T Receive Timing (End of Packet)
Electrical Specifications
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
85
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
9.6.17 10Mb/s Jabber Timing
Table 9-17. 10Mb/s Jabber Timing
PARAMETER
t1
Jabber Activation Time
t2
Jabber Deactivation Time
TEST CONDITIONS
MIN
TYP
MAX
100
10 Mb/s MII mode
UNIT
ms
500
TX_EN
t1
PMD Output Pair
t2
COL
Figure 9-17. 10Mb/s Jabber Timing
9.6.18 10Base-T Normal Link Pulse Timing
Table 9-18. 10Base-T Normal Link Pulse Timing
PARAMETER (1)
t1
Pulse Period
t2
Pulse Width
(1)
TEST CONDITIONS
MIN
10 Mb/s MII mode
TYP
MAX
UNIT
16
ms
100
ns
Transmit timing
t1
t2
Normal Link Pulse(s)
T0358-01
Figure 9-18. 10Base-T Normal Link Pulse Timing
86
Electrical Specifications
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
9.6.19 Auto-Negotiation Fast Link Pulse (FLP) Timing
Table 9-19. Auto-Negotiation Fast Link Pulse (FLP) Timing
PARAMETER
TEST CONDITIONS
t1
Clock Pulse to Clock Pulse Period
t2
Clock Pulse to Data Pulse Period
t3
Clock, Data Pulse Width
t4
FLP Burst to FLP Burst Period
t5
Burst Width
MIN
Data = 1
TYP
MAX
UNIT
125
μs
62
μs
114
ns
16
ms
2
ms
t1
t2
t3
t3
Fast Link Pulse(s)
Data
Pulse
Clock
Pulse
Clock
Pulse
t4
t5
FLP Burst
FLP Burst
T0359-01
Figure 9-19. Auto-Negotiation Fast Link Pulse (FLP) Timing
Electrical Specifications
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
87
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
9.6.20 100Base-TX Signal Detect Timing
Table 9-20. 100Base-TX Signal Detect Timing
MAX
UNIT
t1
SD Internal Turn-on Time
PARAMETER
TEST CONDITIONS
MIN
TYP
100
μs
t2
Internal Turn-off Time
200
μs
PMD Input Pair
t1
t2
SD+ Intermal
T0360-01
NOTE: The signal amplitude on PMD Input Pair must be TP-PMD compliant.
Figure 9-20. 100Base-TX Signal Detect Timing
9.6.21 100Mbs Loopback Timing
Table 9-21. 100Mbs Loopback Timing
PARAMETER
t1
TX_EN to RX_DV Loopback
MIN
TYP
MAX
100Mbs external loopback
TEST CONDITIONS
241
242
243
100Mbs external loopback – fast RX_DV mode
201
202
203
100Mbs analog loopback
232
233
234
100Mbs PCS Input loop back
120
121
122
8
9
10
100Mbs MII loop back
88
Electrical Specifications
UNIT
ns
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
TX_CLK
TX_EN
TXD[3:0]
CRS
t1
RX_CLK
RX_DV
RXD[3:0]
T0361-01
(1)
(2)
(3)
(4)
Due to the nature of the descrambler function, all 100Base-TX Loopback modes cause an initial dead-time of up to 550 μs during
which time no data is present at the receive MII outputs. The 100Base-TX timing specified is based on device delays after the initial
550µs dead-time.
Measurement is made from the first rising edge of TX_CLK after assertion of TX_EN.
External loopback was measured using very short external cable (approximately 10cm).
Since MII loopback introduce extreme short roundtrip delay, some hosts would use PCS Input loopback (Mainly in 100BT).
Figure 9-21. 100Mbs Loopback Timing
Electrical Specifications
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
89
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
9.6.22 10Mbs Internal Loopback Timing
Table 9-22. 10Mbs Internal Loopback Timing
PARAMETER
t1
TEST CONDITIONS
TX_EN to RX_DV Loopback
MIN
TYP
10Mbs internal loopback mode
MAX
UNIT
μs
1.7
TX_CLK
TX_EN
TXD[3:0]
CRS
t1
RX_CLK
RX_DV
RXD[3:0]
T0362-01
(1)
(2)
Measurement is made from the first rising edge of TX_CLK after assertion of TX_EN.
Analog loopback was used. Looping the TX to RX at the analog input/output stage.
Figure 9-22. 10Mbs Internal Loopback Timing
9.6.23 RMII Transmit Timing
Table 9-23. RMII Transmit Timing
PARAMETER
TEST CONDITIONS
MIN
50MHz Reference
Clock
t1
XI Clock Period
t2
TXD[1:0] and TX_EN data setup to X1 rising
1.4
t3
TXD[1:0] and TX_EN data hold to X1 rising
2.0
t4
XI Clock to PMD Output Pair Latency
TYP MAX
UNIT
20
ns
12
bits
t1
XI
t2
TXD[1:0]
TX_EN
t3
Valid Data
t4
Symbol
PMD Output Pair
Figure 9-23. RMII Transmit Timing
90
Electrical Specifications
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
TLK105
TLK106
www.ti.com
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
9.6.24 RMII Receive Timing
Table 9-24. RMII Receive Timing
PARAMETER
TEST CONDITIONS
MIN
XI Clock Period
t2
RXD[1:0], CRS_DV, RX_DV and RX_ER output delay from XI rising
t3
CRS ON delay
From JK symbol on PMD
Receive Pair to initial
assertion of CRS_DV
17.6
t4
CRS OFF delay
From TR symbol on PMD
Receive Pair to initial
assertion of CRS_DV
26.2
t5
RXD[1:0] and RX_ER latency
From symbol on Receive
Pair. * Elasticity buffer set
to default value (01)
29.7
t6
RX_CLK Clock Period
50MHz “Recovered clock”
while working in “RMII
receive clock” mode
20
t7
RXD[1:0], CRS_DV, RX_DV and RX_ER output delay from RX_CLK
rising
While working in “RMII
receive clock” mode
3.8
PMD
Input Pair Idle
50MHz Reference Clock
TYP MAX
t1
(J/K)
4
(TR)
Data
20
t5
10.8
14
UNIT
ns
bits
ns
Data
t4
XI
t2
RX_DV
t1
t2
t2
t6
t7
t7
t3
CRS_DV
t2
RXD[1:0]
RX_ER
RX_CLK
t7
Figure 9-24. RMII Receive Timing
NOTE
1. Per the RMII Specification, output delays assume a 25pF load.
2. CRS_DV is asserted asynchronously in order to minimize latency of control signals
through the PHY. CRS_DV may toggle synchronously at the end of the packet to indicate
CRS de-assertion.
3. RX_DV is synchronous to XI. While not part of the RMII specification, this signal is
provided to simplify recovery of receive data.
4. “RMII receive clock” mode is not part of the RMII specification that allows synchronization
of the MAC-PHY RX interface in RMII mode. Setting register 0x000A bit [0] is required to
activate this mode.
Electrical Specifications
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
91
TLK105
TLK106
SLLSEB8A – AUGUST 2012 – REVISED MARCH 2013
www.ti.com
9.6.25 Isolation Timing
Table 9-25. Isolation Timing
PARAMETER
t1
TEST CONDITIONS
MIN
TYP MAX
From Deassertion of S/W or H/W Reset to transition from Isolate to Normal
mode
71
UNIT
ns
H/W or S/W Reset
t1
ISOLATE
MODE
NORMAL
T0365-01
Figure 9-25. Isolation Timing
9.6.26 25MHz_OUT Clock Timing
Table 9-26. 25MHz_OUT Clock Timing
PARAMETER
t1
t2
t3
(1)
TEST CONDITIONS
25MHz_OUT (1) propagation delay
25MHz_OUT (1) High Time
25MHz_OUT
(1)
Low Time
MIN
TYP
Relative to XI
MAX
8
MII mode
20
RMII mode
10
MII mode
20
RMII mode
10
UNIT
ns
ns
25MHz_OUT characteristics are dependent upon the XI input characteristics.
XI
t1
t2
t3
25MHz_OUT
T0366-01
Figure 9-26. 25MHz_OUT Timing
92
Electrical Specifications
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLK105 TLK106
PACKAGE OPTION ADDENDUM
www.ti.com
10-Mar-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package Qty
Drawing
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
TLK105RHBR
ACTIVE
QFN
RHB
32
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
TLK105
TLK105RHBT
ACTIVE
QFN
RHB
32
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
TLK105
TLK106RHBR
ACTIVE
QFN
RHB
32
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 105
TLK106
TLK106RHBT
ACTIVE
QFN
RHB
32
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 105
TLK106
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Only one of markings shown within the brackets will appear on the physical device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
10-Mar-2013
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Mar-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
TLK105RHBR
QFN
RHB
32
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3000
330.0
12.4
5.3
5.3
1.5
8.0
12.0
Q2
TLK105RHBT
QFN
RHB
32
250
180.0
12.4
5.3
5.3
1.5
8.0
12.0
Q2
TLK106RHBR
QFN
RHB
32
3000
330.0
12.4
5.3
5.3
1.5
8.0
12.0
Q2
TLK106RHBT
QFN
RHB
32
250
180.0
12.4
5.3
5.3
1.5
8.0
12.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Mar-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TLK105RHBR
QFN
RHB
32
3000
367.0
367.0
35.0
TLK105RHBT
QFN
RHB
32
250
210.0
185.0
35.0
TLK106RHBR
QFN
RHB
32
3000
367.0
367.0
35.0
TLK106RHBT
QFN
RHB
32
250
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated