19-2037; Rev 0; 5/01 14-Bit ADC, 200ksps, +5V Single-Supply with Reference The MAX1142/MAX1143 are 200ksps, 14-bit ADCs. These serially interfaced ADCs connect directly to SPI™, QSPI™, and MICROWIRE™ devices without external logic. They combine an input scaling network, internal track/hold, a clock, +4.096V reference, and three general-purpose digital output pins (for external multiplexer or PGA control) in a 20-pin SSOP package. The excellent dynamic performance (SINAD ≥ 81dB), high-speed (200ksps), and low power (7.5mA) of these ADCs, make them ideal for applications such as industrial process control, instrumentation, and medical applications. The MAX1142 accepts input signals of 0 to +12V (unipolar) or ±12V (bipolar), while the MAX1143 accepts input signals of 0 to +4.096V (unipolar) or ±4.096V (bipolar). Operating from a single +4.75V to +5.25V analog supply and a +4.75V to +5.25V digital supply, power-down modes reduce current consumption to 1mA at 10ksps and further reduce supply current to less than 20µA at slower data rates. A serial strobe output (SSTRB) allows direct connection to the TMS320-family of digital signal processors. The MAX1142/MAX1143 user can select either the internal clock, or an external serial-interface clock for the ADC to perform analog-to-digital conversions. The MAX1142/MAX1143 feature internal calibration circuitry to correct linearity and offset errors. On-demand calibration allows the user to optimize performance. Three user-programmable logic outputs are provided for the control of an 8-channel MUX or a PGA. Applications Industrial Process Control Features ♦ 200ksps (Bipolar) and 150ksps (Unipolar) Sampling ADC ♦ 14-Bits, No Missing Codes ♦ 1LSB INL Guaranteed ♦ 81dB (min) SINAD ♦ +5V Single-Supply Operation ♦ Low Power Operation, 7.5mA (Unipolar Mode) ♦ 2.5µA Shutdown Mode ♦ Software-Configurable Unipolar & Bipolar Input Ranges 0 to +12V and ±12V (MAX1142) 0 to +4.096V and ±4.096V (MAX1143) Internal or External Reference ♦ Internal or External Clock ♦ SPI/QSPI/MICROWIRE-Compatible Wire Serial Interface ♦ Three User-Programmable Logic Outputs ♦ Small 20-Pin SSOP Package Ordering Information PART TEMP. RANGE PINPACKAGE INL (LSB) MAX1142ACAP 0°C to +70°C 20 SSOP ±1 MAX1142BCAP 0°C to +70°C 20 SSOP ±2 Ordering Information continued at end of data sheet. Industrial I/O Modules Pin Configuration Data-Acquisition Systems Medical Instruments Portable and Battery-Powered Equipment TOP VIEW REF 1 20 AIN REFADJ 2 19 AGND AGND 3 18 CREF AVDD 4 DGND 5 SHDN Functional Diagram appears at end of data sheet. Typical Application Circuit appears at end of data sheet. SPI and QSPI are trademarks of Motorola, Inc. MICROWIRE is a trademark of National Semiconductor Corp. 6 17 CS MAX1142 MAX1143 16 DIN 15 DVDD P2 7 14 DGND P1 8 13 SCLK P0 9 12 RST SSTRB 10 11 DOUT SSOP ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 MAX1142/MAX1143 General Description MAX1142/MAX1143 14-Bit ADC, 200ksps, +5V Single-Supply with Reference ABSOLUTE MAXIMUM RATINGS AVDD to AGND, DVDD to DGND .............................-0.3V to +6V AGND to DGND.....................................................-0.3V to +0.3V AIN to AGND.....................................................................±16.5V REFADJ, CREF, REF to AGND.................-0.3V to (AVDD + 0.3V) Digital Inputs to DGND.............................................-0.3V to +6V Digital Outputs to DGND .........................-0.3V to (DVDD + 0.3V) Continuous Power Dissipation (TA = +70°C) 20-SSOP (derate 8.00mW/°C above +70°C) ...............640mW Operating Temperature Ranges MAX114_CAP ......................................................0°C to +70°C MAX114_EAP....................................................-40°C to +85°C Storage Temperature Range .............................-60°C to +150°C Junction Temperature ......................................................+150°C Lead Temperature (soldering, 10s) .................................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (AVDD = DVDD = +5V ±5%, fSCLK = 4.8MHz, external clock (50% duty cycle), 24 clocks/conversion (200ksps), bipolar input, external VREF = +4.096V, VREFADJ = AVDD, CREF = 2.2µF, CCREF = 1µF, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DC ACCURACY (Note 1) Resolution 14 Relative Accuracy (Note 2) INL Differential Nonlinearity DNL Unipolar Mode ±1 MAX114_B ±2 ±1 Unipolar Mode Transition Noise Offset Error Gain Error (Note 3) Bits MAX114_A 0.34 LSB LSB LSB RMS Unipolar ±4 Bipolar ±6 Unipolar ±0.2 Bipolar ±0.3 mV %FSR Offset Drift (Bipolar and Unipolar) Excluding reference drift ±1 ppm/oC Gain Drift (Bipolar and Unipolar) Excluding reference drift ±1 ppm/oC DYNAMIC SPECIFICATIONS (5kHz sine-wave input, 200ksps, 4.8MHz clock, bipolar input mode). (MAX1142, 24Vp-p. MAX1143, 8.192Vp-p) SINAD SNR THD SFDR fIN = 5kHz 81 fIN = 100kHz dB 82 fIN = 5kHz 82 fIN = 100kHz dB 82 fIN = 5kHz -88 fIN = 100kHz 91 fIN = 5kHz 90 fIN = 100kHz dB dB 95 ANALOG INPUT MAX1142 Input Range MAX1143 2 Unipolar Bipolar Unipolar Bipolar 0 12 -12 12 0 4.096 -4.096 4.096 _______________________________________________________________________________________ V 14-Bit ADC, 200ksps, +5V Single-Supply with Reference (AVDD = DVDD = +5V ±5%, fSCLK = 4.8MHz, external clock (50% duty cycle), 24 clocks/conversion (200ksps), bipolar input, external VREF = +4.096V, VREFADJ = AVDD, CREF = 2.2µF, CCREF = 1µF, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER SYMBOL CONDITIONS MAX1142 Input Impedance MAX1143 Unipolar MIN TYP 7.5 10.0 Bipolar 5.9 7.9 Unipolar 100 1000 Bipolar 3.4 4.5 Input Capacitance MAX UNITS kΩ 32 pF 4 MHz CONVERSION RATE Internal Clock Frequency Aperture Delay tAD 10 ns Aperture Jitter tAJ 50 ps MODE 1 (24 External Clock Cycles per Conversion) External Clock Frequency fSCLK Sample Rate fS = fSCLK /24 Conversion Time (Note 4) tCONV+ACQ = 24 / fSCLK Unipolar 0.1 3 Bipolar 0.1 4.8 Unipolar 4.17 125 Bipolar 4.17 200 Unipolar 8 240 Bipolar 5 240 MHz ksps µs MODE 2 (Internal Clock Mode) External Clock Frequency (Data Transfer Only) Conversion Time SSTRB Low Pulse Width Acquisition Time 4 Unipolar 1.82 Bipolar 1.14 8 MHz 6 µs µs MODE 3 (32 External Clock Cycles per Conversion) External Clock Frequency fSCLK Unipolar or Bipolar 0.1 4.8 MHz Sample Rate fS = fSCLK /32 Unipolar or Bipolar 3.125 150 ksps Conversion Time (Note 4) tCONV+ACQ = 32 / fSCLK Unipolar or Bipolar 6.67 320 µs 4.136 V INTERNAL REFERENCE Output Voltage VREF 4.056 4.096 REF Short Circuit Current 24 mA Output Tempco ±20 ppm/oC Capacitive Bypass at REF 0.47 Maximum Capacitive Bypass at REFADJ 10 REFADJ Output Voltage REFADJ Input Range 10 For small adjustments from 4.096V µF µF 4.096 V ±100 mV _______________________________________________________________________________________ 3 MAX1142/MAX1143 ELECTRICAL CHARACTERISTICS (continued) MAX1142/MAX1143 14-Bit ADC, 200ksps, +5V Single-Supply with Reference ELECTRICAL CHARACTERISTICS (continued) (AVDD = DVDD = +5V ±5%, fSCLK = 4.8MHz, external clock (50% duty cycle), 24 clocks/conversion (200ksps), bipolar input, external VREF = +4.096V, VREFADJ = AVDD, CREF = 2.2µF, CCREF = 1µF, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER SYMBOL REFADJ Buffer Disable Threshold CONDITIONS MIN To power-down the internal reference AVDD 0.5V Buffer Voltage Gain TYP MAX UNITS AVDD 0.1V V 1 V/V EXTERNAL REFERENCE (Reference buffer disabled. Reference applied to REF) Input Range (Notes 5 and 6) 3.0 Input Current 4.096 VREF = 4.096V, fSCLK = 4.8MHz 250 VREF = 4.096V, fSCLK = 0 230 In power-down, fSCLK = 0 0.1 4.2 V µA DIGITAL INPUTS Input High Voltage VIH Input Low Voltage VIL Input Leakage IIN Input Hysteresis Input Capacitance 2.4 V VIN = 0 or DVDD 0.8 V ±1 µA VHYST 0.2 V CIN 10 pF DIGITAL OUTPUTS Output High Voltage VOH Output Low Voltage VOL Three-State Leakage Current IL Three-State Output Capacitance ISOURCE = 0.5mA DVDD 0.5 V ISINK = 5mA 0.4 ISINK = 16mA 0.8 CS = DVDD ±10 CS = DVDD 10 V µA pF POWER SUPPLIES Analog Supply (Note 7) AVDD 4.75 5 5.25 V Digital Supply (Note 7) DVDD 4.75 5 5.25 V 5 8 Bipolar Mode SHDN = 0, or software power-down mode 8.5 11 0.3 10 µA Unipolar or Bipolar Mode SHDN = 0, or software power-down mode 2.5 3.5 mA 2.2 10 µA AVDD = DVDD = 4.75V to 5.25V, 72 Unipolar Mode Analog Supply Current Digital Supply Current Power Supply Rejection Ratio (Note 8) 4 IANALOG IDIGITAL PSRR _______________________________________________________________________________________ mA dB 14-Bit ADC, 200ksps, +5V Single-Supply with Reference MAX1142/MAX1143 TIMING CHARACTERISTICS (Figures 5 and 6) (AVDD = DVDD = +5V ±5%, TA = TMIN to TMAX, unless otherwise noted.) PARAMETER Acquisition Time SYMBOL CONDITIONS MIN TYP MAX UNIT µs tACQ 1.14 DIN to SCLK Setup tDS 50 DIN to SCLK Hold tDH 0 ns SCLK to DOUT Valid tDO 70 ns CS Fall to DOUT Enable tDV CLOAD = 50pF 80 ns CS Rise to DOUT Disable tTR CLOAD = 50pF 80 ns ns CS to SCLK Rise Setup tCSS 100 ns CS to SCLK Rise Hold tCSH 0 ns SCLK High Pulse Width tCH 80 ns SCLK Low Pulse Width tCL 80 SCLK Fall to SSTRB tSSTRB ns CLOAD = 50pF 80 ns ns CS Fall to SSTRB Enable tSDV CLOAD = 50pF, External clock mode 80 CS Rise to SSTRB Disable tSTR CLOAD = 50pF, External clock mode 80 SSTRB Rise to SCLK Rise tSCK Internal clock mode RST Pulse Width tRS ns 0 ns 208 ns Note 1: Tested at AVDD = DVDD = +5V, bipolar input mode. Note 2: Relative accuracy is the deviation of the analog value at any code from its theoretical value after the gain error and offset error have been nulled. Note 3: Offset nulled. Note 4: Conversion time is defined as the number of clock cycles multiplied by the clock period, clock has 50% duty cycle. Includes the acquisition time. Note 5: ADC performance is limited by the converter’s noise floor, typically 300µVp-p. Note 6 When an external reference has a different voltage than the specified typical value, the full scale of the ADC will scale proportionally. Note 7: Electrical characteristics are guaranteed from AVDD(MIN) = DVDD(MIN) to AVDD(MAX) = DVDD(MAX). For operations beyond this range, see the Typical Operating Characteristics. For guaranteed specifications beyond the limits, contact the factory. Note 8: Defined as the change in positive full-scale caused by a ±5% variation in the nominal supply voltage. _______________________________________________________________________________________ 5 Typical Operating Characteristics (MAX1142/MAX1143, AVDD = DVDD = +5V , fSCLK = 4.8MHz, external clock (50% duty cycle), 24-clocks/conversion (200ksps), bipolar input, external REF = +4.096V, 0.22µF bypassing on REFADJ, 2.2µF on REF, 1µF on CREF, TA = 25°C, unless otherwise noted.) 0.4 0.2 0 -0.2 -0.4 -0.6 0.5 0 -0.5 10.7 C 10.5 B 10.3 10.1 A 9.9 3263 1632 6525 4894 DIGITAL OUTPUT CODE OFFSET VOLTAGE vs. TEMPERATURE GAIN ERROR vs. TEMPERATURE B C GAIN ERROR (% FULL SCALE) -1 0.04 A: AVDD, DVDD = +4.75V B: AVDD, DVDD = +5.00V C: AVDD, DVDD = +5.25V 0.03 C 0.02 B 0.01 -4 A -20 0 20 40 TEMPERATURE (°C) 60 80 0 20 40 60 80 TEMPERATURE (°C) 100 10 1 0.1 0.01 0 -40 -20 TOTAL SUPPLY CURRENT vs. CONVERSION RATE (USING SHUTDOWN) MAX1142/3 toc05 DIGITAL OUTPUT CODE A: AVDD, DVDD = +4.75V B: AVDD, DVDD = +5.00V C: AVDD, DVDD = +5.25V -40 9787 13049 1631 8156 11418 14680 MAX1142/3 toc06 1 10297 13729 8581 12013 15445 TOTAL SUPPLY CURRENT (mA) 5149 6865 MAX1142/3 toc04 1717 3433 A 6 10.9 9.5 -1.0 1 -3 11.1 9.7 -1.0 -2 A: AVDD, DVDD = +4.75V B: AVDD, DVDD = +5.00V C: AVDD, DVDD = +5.25V 11.3 -0.8 0 MAX1142/3 toc03 11.5 TOTAL SUPPLY CURRENT (mA) 0.6 1.0 MAX1142 toc02 0.8 DIFFERENTIAL NONLINEARITY (LSB) MAX1142 toc01 1.0 INTEGRAL NONLINEARITY (LSB) TOTAL SUPPLY CURRENT vs. TEMPERATURE DIFFERENTIAL NONLINEARITY vs. DIGITAL OUTPUT CODE INTEGRAL NONLINEARITY vs. DIGITAL OUTPUT CODE OFFSET VOLTAGE (V) MAX1142/MAX1143 14-Bit ADC, 200ksps, +5V Single-Supply with Reference -40 -20 0 20 40 TEMPERATURE (°C) 60 80 0 1 10 100 CONVERSION RATE (ksps) _______________________________________________________________________________________ 1000 14-Bit ADC, 200ksps, +5V Single-Supply with Reference fSAMPLE = 200kHz fIN = 5kHz -20 -40 -60 -80 fSAMPLE = 200kHz 90 80 AMPLITUDE (dB) AMPLITUDE (dB) 1 100 MAX1142/3 toc08 MAX1142/3 toc07 0 1.005 70 60 50 40 30 0.995 20 -110 10 0 -120 0 20 40 60 80 0 TEMPERATURE (°C) 9 0.1 18 27 36 45 54 63 72 81 90 99 FREQUENCY (kHz) fSAMPLE = 200kHz 1 10 100 FREQUENCY (kHz) SFDR PLOT 120 110 100 THD PLOT 0 90 80 fSAMPLE = 200kHz -10 -20 -30 AMPLITUDE (dB) -20 MAX1142/3 toc10 -40 MAX1142/3 toc11 0.990 AMPLITUDE (dB) NORMALIZED REF VOLTAGE SINAD PLOT FFT PLOT 1.010 MAX1142/3 toc09 NORMALIZED REF VOLTAGE vs. TEMPERATURE 70 60 50 40 -40 -50 -60 -70 30 20 -80 10 0 -100 -90 -110 0.1 1 10 FREQUENCY (kHz) 100 0.1 1 10 100 FREQUENCY (kHz) _______________________________________________________________________________________ 7 MAX1142/MAX1143 Typical Operating Characteristics (continued) (MAX1142/MAX1143, AVDD = DVDD = +5V , fSCLK = 4.8MHz, external clock (50% duty cycle), 24-clocks/conversion (200ksps), bipolar input, external REF = +4.096V, 0.22µF bypassing on REFADJ, 2.2µF on REF, 1µF on CREF, TA = 25°C, unless otherwise noted.) 14-Bit ADC, 200ksps, +5V Single-Supply with Reference MAX1142/MAX1143 Pin Description PIN 8 NAME FUNCTION Reference Buffer Output/ADC Reference Input. Reference voltage for analog-to-digital conversion. In internal reference mode, the reference buffer provides a +4.096V nominal output, externally adjustable at REFADJ. In external reference mode, disable the internal buffer by pulling REFADJ to AVDD. Bypass to AGND with a 2.2µF capacitor when using the internal reference. 1 REF 2 REFADJ 3 AGND Analog Ground. This is the primary analog ground (Star Ground). 4 AVDD Analog Supply 5V ±5%. Bypass AVDD to AGND (pin 3) with a 0.1µF capacitor. 5 DGND Digital Ground 6 SHDN Shutdown Control Input. Drive SHDN low to put the ADC in shutdown mode. 7 P2 User-Programmable Output 2 8 P1 User-Programmable Output 1 9 P0 User-Programmable Output 0 10 SSTRB Serial Strobe Output. In internal clock mode, SSTRB goes low when the ADC begins a conversion and goes high when the conversion is finished. In external clock mode, SSTRB pulses high for one clock period before the MSB decision. It is high impedance when CS is high in external clock mode. 11 DOUT Serial Data Output. MSB first, straight binary format for unipolar input, two’s complement for bipolar input. Each bit is clocked out of DOUT at the falling edge of SCLK. 12 RST Reset Input. Drive RST low to put the device in the power-on default mode. See the Power-On Reset section. 13 SCLK Serial Data Clock Input. Serial data on DIN is loaded on the rising edge of SCLK, and serial data is updated on DOUT on the falling edge of SCLK. In external clock mode, SCLK sets the conversion speed. 14 DGND Digital Ground. Connect to pin 5. 15 DVDD Digital Supply 5V ±5%. Bypass DVDD to DGND (pin 14) with a 0.1µF capacitor. 16 DIN Serial Data Input. Serial data on DIN is latched on the rising edge of SCLK. 17 CS Chip Select Input. Drive CS low to enable the serial interface. When CS is high, DOUT is high-impedance. In external clock mode SSTRB is high-impedance when CS is high. 18 CREF Reference Buffer Bypass. Bypass CREF to AGND (pin 3) with 1µF. 19 AGND Analog Ground. Connect pin 19 to pin 3. 20 AIN Bandgap Reference Output/Bandgap Reference Buffer Input. Bypass to AGND with 0.22µF. When using an external reference, connect REFADJ to AVDD to disable the internal bandgap reference. Analog Input _______________________________________________________________________________________ 14-Bit ADC, 200ksps, +5V Single-Supply with Reference The MAX1142/MAX1143 analog-to-digital converters (ADCs) use a successive-approximation technique and input track/hold (T/H) circuitry to convert an analog signal to a 14-bit digital output. The MAX1142/MAX1143 easily interfaces to microprocessors (µPs). The data bits can be read either during the conversion in external clock mode or after the conversion in internal clock mode. In addition to a 14-bit ADC, the MAX1142/MAX1143 include an input scaler, an internal digital microcontroller, calibration circuitry, an internal clock generator, and an internal bandgap reference. The input scaler for the MAX1142 enables conversion of input signals ranging from 0 to +12V (unipolar input) or ±12V (bipolar input). The MAX1143 accepts 0 to +4.096V (unipolar input) or ±4.096V (bipolar input). Input range selection is software controlled. BIPOLAR Offsets resulting from synchronous noise (such as the conversion clock) are canceled by the MAX1142/ MAX1143’s calibration circuitry. However, because the magnitude of the offset produced by a synchronous signal depends on the signal’s shape, recalibration may be appropriate if the shape or relative timing of the clock or other digital signals change, as might occur if more than one clock signal or frequency is used. Input Scaler The MAX1142/MAX1143 have an input scaler which allows conversion of true bipolar input voltages while operating from a single +5V supply. The input scaler attenuates and shifts the input, as necessary, to map the external input range to the input range of the internal DAC. The MAX1142 analog input range is 0 to +12V (unipolar) or ±12V (bipolar). The MAX1143 analog input range is 0 to +4.096V (unipolar) or ±4.096V (bipolar). Unipolar and bipolar mode selection is configured with bit 6 of the serial Control-Byte. Figure 1 shows the equivalent input circuit of the MAX1142/MAX1143. The resistor network on the analog input provides ±16.5V fault protection. This circuit limits the current going into or out of the pin, to less than 2mA. The overvoltage protection is active, even if the device is in a power-down mode, or if AVDD = 0. VOLTAGE REFERENCE S1 UNIPOLAR R1 2.5kΩ R2 CHOLD 30pF TRACK S2 AIN T/H OUT R3 HOLD TRACK HOLD S3 S1 = BIPOLAR/UNIPOLAR S2, S3 = T/H SWITCH R2 = 7.6kΩ (MAX1142) OR 2.5kΩ (MAX1143) R3 = 3.9kΩ (MAX1142) OR INFINITY (MAX1143) Calibration To minimize linearity, offset, and gain errors, the MAX1142/MAX1143 have on-demand software calibration. Initiate calibration by writing a Control-Byte with bit M1 = 0, and bit M0 = 1 (See Table 1). Select internal or external clock for calibration by setting the INT/EXT bit in the Control-Byte. Calibrate the MAX1142/MAX1143 with the clock used for performing conversions. MAX1142/MAX1143 Detailed Description Figure 1. Equivalent Input Circuit Digital Interface The digital interface pins consist of SHDN, RST, SSTRB, DOUT, SCLK, DIN and CS. Bringing SHDN low, places the MAX1142/MAX1143 in its 2.5µA shutdown mode. A logic low on RST halts the MAX1142/MAX1143 operation and returns the part to its power-on reset state. In external clock mode, SSTRB is low and pulses high for one clock cycle at the start of conversion. In internal clock mode SSTRB goes low at the start of the conversion, and goes high to indicate the conversion is finished. The DIN input accepts Control-Byte data which is clocked in on each rising edge of SCLK. After CS goes low or after a conversion or calibration completes, the first logic “1” clocked-into DIN is interpreted as the START bit, the MSB of the 8-bit Control-Byte. The SCLK input is the serial data transfer clock which clocks data in and out of the MAX1142/MAX1143. SCLK also drives the A/D conversion steps in external clock mode (see Internal and External Clock Modes section). DOUT is the serial output of the conversion result. DOUT is updated on the falling edge of SCLK. DOUT is high-impedance when CS is high. CS must be low for the MAX1142/MAX1143 to accept a Control-Byte. The serial interface is disabled when CS is high. _______________________________________________________________________________________ 9 MAX1142/MAX1143 14-Bit ADC, 200ksps, +5V Single-Supply with Reference User-Programmable Outputs The MAX1142/MAX1143 have three user-programmable outputs: P0, P1 and P2. The power-on default state for the programmable outputs is zero. These are pushpull CMOS outputs suitable for driving a multiplexer, a PGA, or other signal preconditioning circuitry. The userprogrammable outputs are controlled by bits 0, 1 and 2 of the Control-Byte (Table 2). The user-programmable outputs are set to zero during power-on reset (POR) or when RST goes low. During hardware or software shutdown P0, P1, and P2 are unchanged and remain low-impedance. Starting a Conversion Start a conversion by clocking a Control-Byte into the device’s internal shift register. With CS low, each rising edge on SCLK clocks a bit from DIN into the MAX1142/MAX1143’s internal shift register. After CS goes low or after a conversion or calibration completes, the first arriving logic “1” is defined as the start bit of the Control-Byte. Until this first start bit arrives, any number of logic “0” bits can be clocked into DIN with no effect. If at any time during acquisition or conversion, CS is brought high and then low again, the part is placed into a state where it can recognize a new start bit. If a new start bit occurs before the current conversion is complete, the conversion is aborted and a new acquisition is initiated. Table 1 shows the Control-Byte format. Internal and External Clock Modes The MAX1142/MAX1143 may use either the external serial clock or the internal clock to perform the successive-approximation conversion. In both clock modes, the external clock shifts data in and out of the MAX1142/MAX1143. Bit 5 (INT/EXT) of the Control-Byte programs the clock mode. External Clock In external clock mode, the external clock not only shifts data in and out, but it also drives the A/D conversion steps. In short acquisition mode, SSTRB pulses high for one clock period after the seventh falling edge of SCLK, following the start bit. The MSB of the conversion is available at DOUT on the eighth falling edge of SCLK (Figure 2). In long acquisition mode, when using the external clock, SSTRB pulses high for one clock period after the fifteenth falling edge of SCLK, following the start bit. The MSB of the conversion is available at DOUT on the sixteenth falling edge of SCLK (Figure 3). Table 1. Control-Byte Format BIT7 (MSB) BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0 (LSB) START UNI/BIP INT/EXT M1 M0 P2 P1 P0 BIT NAME 7 (MSB) START The first logic “1” bit, after CS goes low, defines the beginning of the Control-Byte 6 UNI/BIP 1 = unipolar, 0 = bipolar. Selects unipolar or bipolar conversion mode. In unipolar mode, analog input signals from 0 to +12V (MAX1142) or 0 to VREF (MAX1143) can be converted. In bipolar mode analog input signals from -12V to +12V (MAX1142) or -VREF to +VREF (MAX1143) can be converted. 5 INT/EXT Selects the internal or external conversion clock. 1 = Internal, 0 = External. 4 M1 3 2 1 0(LSB) 10 M0 P2 P1 P0 DESCRIPTION M1 M0 MODE 0 0 24 External clocks per conversion (short acquisition mode) 0 1 Start Calibration. Starts internal calibration 1 0 Software power-down mode 1 1 32 External clocks per conversion (long acquisition mode) These three bits are stored in a port register and output to pins P2–P0 for use in addressing a MUX or PGA. These three bits are updated in the port register simultaneously when a new Control-Byte is written. ______________________________________________________________________________________ 14-Bit ADC, 200ksps, +5V Single-Supply with Reference OUTPUT PIN PROGRAMMED THROUGH CONTROLBYTE POWER-ON OR RST DEFAULT P2 Bit 2 0 P1 Bit 1 0 P0 Bit 0 0 DESCRIPTION User programmable outputs follow the state of the Control-Byte’s three LSBs, and are updated simultaneously when a new Control-Byte is written. Outputs are push-pull. In hardware and software shutdown, these outputs are unchanged and remain low-impedance. In external clock mode, SSTRB is high-impedance when CS is high. In external clock mode, CS is normally held low during the entire conversion. If CS goes high during the conversion, SCLK is ignored until CS goes low. This allows external clock mode to be used with 8bit bytes. Internal Clock In internal clock mode, the MAX1142/MAX1143 generates its own conversion clock. This frees the microprocessor from the burden of running the SAR conversion clock, and allows the conversion results to be read back at the processor’s convenience, at any clock rate up to 8MHz. SSTRB goes low at the start of the conversion and goes high when the conversion is complete. SSTRB will be low for a maximum of 6µs, during which time SCLK should remain low for best noise performance. An internal register stores data when the conversion is in progress. SCLK clocks the data out of the internal storage register at any time after the conversion is complete. The MSB of the conversion is available at DOUT when SSTRB goes high. The subsequent 15 falling edges on SCLK shift the remaining bits out of the internal storage register (Figure 4). CS does not need to be held low once a conversion is started. When internal clock mode is selected, SSTRB does not go into a high-impedance state when CS goes high. Figure 5 shows the SSTRB timing in internal clock mode. In internal clock mode, data can be shifted into the MAX1142/MAX1143 at clock rates up to 4.8MHz, provided that the minimum acquisition time, tACQ, is kept above 1.14µs in bipolar mode and 1.82µs in unipolar-mode. Data can be clocked out at 8MHz. Output Data The output data format is straight binary for unipolar conversions and two’s complement in bipolar mode. In both modes the MSB is shifted out of the MAX1142/ MAX1143 first. CS tACQ SCLK DIN 1 4 UNI/ START BIP INT/ EXT M1 8 M0 P2 P1 15 12 21 24 P0 SSTRB B13 MSB DOUT A/D STATE IDLE ACQUISITION B12 B11 B10 B9 B8 B7 CONVERSION B2 B1 B0 LSB X X FILLED WITH ZEROS IDLE Figure 2. Short Acquisition Mode (24-Clock Cycles) External Clock, Bipolar Mode ______________________________________________________________________________________ 11 MAX1142/MAX1143 Table 2. User-Programmable Outputs MAX1142/MAX1143 14-Bit ADC, 200ksps, +5V Single-Supply with Reference CS tACQ 1 SCLK UNI/ START BIP DIN 4 INT/ EXT M1 15 8 P2 M0 P1 19 21 32 P0 SSTRB B13 MSB DOUT A/D STATE IDLE B12 B11 ACQUISITION B2 B1 B0 LSB X X FILLED WITH ZEROS CONVERSION IDLE Figure 3. Long Acquisition Mode (32-Clock Cycles) External Clock, Bipolar Mode CS tACQ 1 SCLK UNI/ START BIP DIN 4 INT/ EXT M1 8 M0 P2 P1 9 10 B13 MSB B12 21 24 P0 SSTRB tCONV DOUT B11 B2 B1 B0 LSB X X FILLED WITH ZEROS Figure 4. Internal Clock Mode Timing, Short Acquisition, Bipolar Mode CS tCONV tCSS tSCK tCSH SSTRB t SSTRB SCLK PO CLOCKED IN NOTE: FOR BEST NOISE PERFORMANCE, KEEP SCLK LOW DURING CONVERSION. Figure 5. Internal Clock Mode SSTRB Detailed Timing 12 ______________________________________________________________________________________ 14-Bit ADC, 200ksps, +5V Single-Supply with Reference OR If a falling edge on CS forces a start bit before the conversion or calibration is complete, then the current operation will be terminated and a new one started. Applications Information Power-On Reset When power is first applied to the MAX1142/MAX1143 or if RST is pulsed low, the internal calibration registers are set to their default values. The user-programmable registers (P0, P1 and P2) are low, and the device is configured for bipolar mode with internal clocking. Calibration To compensate the MAX1142/MAX1143 for temperature drift and other variations, they should be periodically calibrated. After any change in ambient temperature more than 10°C, the device should be recalibrated. A 100mV change in supply voltage or any change in the reference voltage should be followed by a calibration. Calibration corrects for errors in gain, offset, integral nonlinearity and differential nonlinearity. The MAX1142/MAX1143 should be calibrated after power-up or the assertion of reset. Make sure the power supplies and the reference voltage have fully settled prior to initiating the calibration sequence. Initiate calibration by setting M1 = 0 and M0 = 1 in the Control-Byte. In internal clock mode, SSTRB goes low at the beginning of calibration and goes high to signal the end of calibration, approximately 80,000 clock cycles later. In external clock mode, SSTRB goes high at the beginning of calibration and goes low to signal the end of calibration. Calibration should be performed in the same clock mode as will be used for conversions (Figure 6). Reference The MAX1142/MAX1143 can be used with an internal or external reference. An external reference can be connected directly at the REF pin or at the REFADJ pin. CREF is an internal reference node and must be bypassed with a 1µF capacitor when using either the internal or an external reference. Internal Reference When using the MAX1142/MAX1143’s internal reference, place a 0.22µF ceramic capacitor from REFADJ to AGND and place a 2.2µF capacitor from REF to AGND. Fine adjustments can be made to the internal reference voltage by sinking or sourcing current at REFADJ. The input impedance of REFADJ is nominally 9kΩ. The internal reference voltage is adjustable to ±1.5% with the circuit of Figure 7. CS tSTR tSDV SSTRB tSSTRB tSSTRB SCLK P1 CLOCKED IN Figure 6. External Clock Mode SSTRB Detailed Timing ______________________________________________________________________________________ 13 MAX1142/MAX1143 Data Framing The falling edge of CS does NOT start a conversion on the MAX1142/MAX1143. The first logic high clocked into DIN is interpreted as a start bit and defines the first bit of the Control-Byte. A conversion starts on the falling edge of SCLK, after the seventh bit of the Control-Byte (the P1 bit) is clocked into DIN. The start bit is defined as: The first high bit clocked into DIN with CS low, anytime the converter is idle, e.g. after AVDD is applied, or as the first high bit clocked into DIN after CS is pulsed high, then low. MAX1142/MAX1143 14-Bit ADC, 200ksps, +5V Single-Supply with Reference External reference An external reference can be placed at either the input (REFADJ) or the output (REF) of the MAX1142/ MAX1143’s internal buffer amplifier. +5V MAX1142 510kΩ 100kΩ When connecting an external reference to REFADJ, the input impedance is typically 9kΩ. Using the buffered REFADJ input makes buffering of the external reference unnecessary. The internal buffer output must be bypassed at REF with a 2.2µF capacitor. When connecting an external reference at REF, REFADJ must be connected to AVDD. The input impedance at REF is 16kΩ for DC currents. During conversion, an external reference at REF must deliver 250µA DC load current and have an output impedance of 10Ω or less. If the reference has a higher output impedance or is noisy, bypass it at the REF pin with a 4.7µF capacitor. REFADJ 0.22µF 24kΩ Figure 7. MAX1142 Reference-Adjust Circuit MAX1143. Unipolar and bipolar mode is programmed with the UNI/BIP bit of the Control-Byte. When using a reference other than the MAX1142/MAX1143’s internal +4.096V reference, the full-scale input range will vary accordingly. The full-scale input range depends on the voltage at REF and the sampling mode selected (Tables 3 and 4). Analog Input The MAX1142/MAX1143 use a capacitive DAC that provides an inherent track/hold function. Drive AIN with a source impedance less than 10Ω. Any signal conditioning circuitry must settle with 16-bit accuracy in less than 500ns. Limit the input bandwidth to less than half the sampling frequency to eliminate aliasing. The MAX1142/MAX1143 has a complex input impedance which varies from unipolar to bipolar mode (Figure 1). Input Acquisition and Settling Clocking-in a Control-Byte starts input acquisition. In bipolar mode, the main capacitor array starts acquiring the input as soon as a start bit is recognized. If unipolar mode is selected by the second DIN bit, the part will immediately switch to unipolar sampling mode and acquire a sample. Acquisition can be extended by eight clock cycles by setting M1 = 1, M0 = 1 (long acquisition mode). The sampling instant in short acquisition completes on the falling edge of the sixth clock cycle after the start bit (Figure 2). Input Range The analog input range in unipolar mode is 0 to +12V for the MAX1142, and 0 to +4.096V for the MAX1143. In bipolar mode, the analog input can be -12V to +12V for the MAX1142, and -4.096V to +4.096V for the Table 3. Unipolar Full Scale and Zero Scale PART REFERENCE MAX1142 MAX1143 ZERO SCALE FULL SCALE Internal 0 +12V External 0 +12(VREF/4.096) Internal 0 +4.096V External 0 +VREF Table 4. Bipolar Full Scale, Zero Scale, and Negative Scale PART MAX1142 MAX1143 14 REFERENCE NEGATIVE FULL SCALE ZERO SCALE FULL SCALE Internal -12V 0 +12V External -12(VREF/4.096) 0 +12(VREF/4.096) Internal -4.096V 0 +4.096V External -VREF 0 +VREF ______________________________________________________________________________________ 14-Bit ADC, 200ksps, +5V Single-Supply with Reference MAX1142/MAX1143 Acquisition is 5.5 clock cycles in short acquisition mode and 13.5 clock cycles in long acquisition mode. Short acquisition mode is 24 clock cycles per conversion. Using the external clock to run the conversion process limits unipolar conversion speed to 125ksps instead of 200ksps in bipolar mode. The input resistance in unipolar mode is larger than that of bipolar mode (Figure1). The RC time constant in unipolar mode is larger than that of bipolar mode, reducing the maximum conversion rate in 24 external clock mode. Long acquisition mode with external clock allows both unipolar and bipolar sampling of 150ksps (4.8MHz/32 clock cycles) by adding eight extra clock cycles to the conversion. Most applications require an input buffer amplifier. If the input signal is multiplexed, the input channel should be switched immediately after acquision, rather than near the end of or after a conversion. This allows more time for the input buffer amplifier to respond to a large step change in input signal. The input amplifier must have a high enough slew-rate to complete the required output voltage change before the beginning of the acquisition time. At the beginning of acquisition, the capacitive DAC is connected to the amplifier output, causing some output disturbance. Ensure that the sampled voltage has settled to within the required limits before the end of the acquisition time. If the frequency of interest is low, AIN can be bypassed with a large enough capacitor to charge the capacitive DAC with very little change in voltage. However, for AC use, AIN must be driven by a wideband buffer (at least 10MHz), which must be stable with the DAC’s capacitive load (in parallel with any AIN bypass capacitor used) and also settle quickly (Figures 8 or 9). 510Ω +5V 0.1µF 2 7 22Ω 6 IN 3 AIN MAX410 4 0.1µF 0.1µF -5V Figure 9. ±5V Buffer for AC/DC Use has ±3.5V Swing Digital Noise Digital noise can couple to AIN and REF. The conversion clock (SCLK) and other digital signals that are active during input acquisition, contribute noise to the conversion result. If the noise signal is synchronous to the sampling interval, an effective input offset is produced. Asynchronous signals produce random noise on the input, whose high-frequency components may be aliased into the frequency band of interest. Minimize noise by presenting a low impedance (at the frequencies contained in the noise signal) at the inputs. This requires bypassing AIN to AGND, or buffering the input with an amplifier that has a small-signal bandwidth of several MHz, or preferably both. AIN has a bandwidth of about 4MHz. 1kΩ +15V 0.1µF 2 1000pF 7 6 AIN IN 3 MAX427 20Ω 4 0.1µF 0.0033µF -15V Figure 8. AIN Buffer for AC/DC Use ______________________________________________________________________________________ 15 MAX1142/MAX1143 14-Bit ADC, 200ksps, +5V Single-Supply with Reference Offsets resulting from synchronous noise (such as the conversion clock) are canceled by the MAX1142/ MAX1143’s calibration scheme. The magnitude of the offset produced by a synchronous signal depends on the signal’s shape. Recalibration may be appropriate if the shape or relative timing of the clock or other digital signals change, as might occur if more than one clock signal or frequency is used. Distortion Avoid degrading dynamic performance by choosing an amplifier with distortion much less than the MAX1142/ MAX1143’s THD (-88dB) at frequencies of interest. If the chosen amplifier has insufficient common-mode rejection, which results in degraded THD performance, use the inverting configuration to eliminate errors from common-mode voltage. Low temperature-coefficient resistors reduce linearity errors caused by resistance changes due to self-heating. To reduce linearity errors due to finite amplifier gain, use an amplifier circuit with sufficient loop gain at the frequencies of interest. DC Accuracy If DC accuracy is important, choose a buffer with an offset much less than the MAX1142/MAX1143’s maximum offset (±6mV), or whose offset can be trimmed while maintaining good stability over the required temperature range. Operating Modes and Serial Interfaces The MAX1142/MAX1143 are fully compatible with MICROWIRE and SPI/QSPI devices. MICROWIRE and SPI/QSPI both transmit a byte and receive a byte at the same time. The simple software interface requires only three 8-bit transfers to perform a conversion, one 8-bit transfer to configure the ADC, and two more 8-bit transfers to clock out the 14-bit conversion result. Mode 1 Short Acquisition Mode (24 SCLK) Configure short acquisition by setting M1 = 0 and M0 = 0. In short acquisition mode, the acquisition time is 5.5 clock cycles. The total period is 24-clock cycles per conversion. Mode 2 Long Acquisition Mode (32 SCLK) Configure long acquisition by setting M1 = 1 and M0 = 1. In long acquisition mode, the acquisition time is 13.5 clock cycles. The total period is 32 clock cycles per conversion. Calibration Mode A calibration is initiated through the serial interface by setting M1 = 0, M0 = 1. Calibration can be done in either internal or external clock mode, though it is desirable that the part be calibrated in the same mode in 16 which it will be used to do conversions. The part will remain in calibration mode for approximately 80,000 clock cycles, unless the calibration is aborted. Calibration is halted if RST or SHDN goes low, or if a valid start condition occurs. Software Shut-Down A software power-down is initiated by setting M1 = 1, M0 = 0. After the conversion completes, the part shuts down. It reawakens upon receiving a new start bit. Conversions initiated with M1 = 1 and M0 = 0 (shutdown) use the acquisition mode selected for the previous conversion. Shutdown Mode The MAX1142/MAX1143 may be shut down by pulling SHDN low or by asserting software shutdown. In addition to lowering power dissipation to 13µW, considerable power can be saved by shutting down the converter for short periods between conversions. Duration will be affected by REF startup time with internal reference. There is no need to perform a calibration after the converter has been shut down, unless the time in shutdown is long enough that the supply voltage or ambient temperature may have changed. Supplies, Layout, Grounding and Bypassing For best system performance, use separate analog and digital ground planes. The two ground planes should be tied together at the MAX1142/MAX1143. Use pins 3 and 14 as the primary AGND and DGND, respectively. If the analog and digital supplies come from the same source, isolate the digital supply from the analog with a low value resistor (10Ω). The MAX1142/MAX1143 are not sensitive to the order of AVDD and DVDD sequencing. Either supply can be present in the absence of the other. Do not apply an external reference voltage until after both AVDD and DVDD are present. Be sure that digital return currents do not pass through the analog ground. All return current paths must be low-impedance. A 5mA current flowing through a PC board ground trace impedance of only 0.05Ω, creates an error voltage of about 250µV, or about 2LSBs error with a ±4V full-scale system. The board layout should ensure that the digital and analog signal lines are kept separate. Do not run analog and digital lines parallel to one another. If you must cross one with the other, do so at right angles. The ADC is sensitive to high-frequency noise on the AVDD power supply. Bypass this supply to the analog ground plane with 0.1µF. If the main supply is not ade- ______________________________________________________________________________________ 14-Bit ADC, 200ksps, +5V Single-Supply with Reference Transfer Function Figures 10 and 11 show the MAX1142/MAX1143’s transfer functions. In unipolar mode, the output data is in binary format and in bipolar mode, it is two’s complement format. OUTPUT CODE Definitions Integral Nonlinearity Integral nonlinearity (INL) is the deviation of the values on an actual transfer function from a straight line. This straight-line can be either a best straight-line fit or a line drawn between the end points of the transfer function, once offset and gain errors have been nullified. INL for the MAX1142/MAX1143 is measured using the endpoint method. Differential Nonlinearity Differential nonlinearity (DNL) is the difference between an actual step width and the ideal value of 1LSB. A DNL error specification of less than 1LSB guarantees no missing codes and a monotonic transfer function. FULL-SCALE TRANSITION 11 . . . 111 11 . . . 110 11 . . . 101 Aperture Jitter FS = +4.096V 1LSB = FS 16384 00 . . . 010 00 . . . 001 Signal-to-Noise Ratio 00 . . . 000 0 1 2 3 FS FS - 3/2LSB INPUT VOLTAGE (LSBs) Figure 10. MAX1143 Unipolar Transfer Function, 4.096V = FullScale OUTPUT CODE +FS = +4.096V -FS = -4.096V 011 . . . 110 000 . . . 010 Aperture Delay Aperture delay (t AD ) is the time between the rising edge of the sampling clock and the instant when an actual sample is taken. 00 . . . 011 011 . . . 111 Aperture jitter (tAJ) is the sample-to-sample variation in the time between the samples. 1LSB = 8.192 16384 000 . . . 001 000 . . . 000 For a waveform perfectly reconstructed from digital samples, signal-to-noise ratio (SNR) is the ratio of fullscale analog input (RMS value) to the RMS quantization error (residual error). The ideal, theoretical, minimum analog-to-digital noise is caused by quantization error only and results directly from the ADC’s resolution (N-bits): SNR = (6.02 ✕ N + 1.76)dB In reality, there are other noise sources besides quantization noise, including thermal noise, reference noise, clock jitter, etc. Therefore, SNR is calculated by taking the ratio of the RMS signal to the RMS noise, which includes all spectral components minus the fundamental, the first five harmonics and the DC offset. Signal-to-Noise Plus Distortion 111 . . . 111 Signal-to-noise plus distortion (SINAD) is the ratio of the fundamental input frequency’s RMS amplitude to the RMS equivalent of all other ADC output signals: SINAD (dB) = 20 ✕ log (SignalRMS/NoiseRMS) 111 . . . 110 111 . . . 101 100 . . . 001 100 . . . 000 -FS 0V +FS - 1LSB INPUT VOLTAGE (LSBs) Figure 11. MAX1143 Bipolar Transfer Function, 4.096V = FullScale ___________________________________________________ 17 MAX1142/MAX1143 quately bypassed, add an additional 1µF or 10µF lowESR capacitor in parallel with the primary bypass capacitor. MAX1142/MAX1143 14-Bit ADC, 200ksps, +5V Single-Supply with Reference Typical Application Circuit Effective Number of Bits Effective number of bits (ENOB) indicates the global accuracy of an ADC at a specific input frequency and sampling rate. An ideal ADC’s error consists of quantization noise only. With an input range equal to the fullscale range of the ADC, calculate the effective number of bits as follows: +5V 0.1µF AVDD ENOB = (SINAD - 1.76) / 6.02 SHDN Total Harmonic Distortion Total harmonic distortion (THD) is the ratio of the RMS sum of the first five harmonics of the input signal to the fundamental itself. This is expressed as: AIN 0.1µF TO DGND THD = 20 × log V2 2 + V3 2 + V4 2 + V5 2 / V1 where V1 is the fundamental amplitude, and V2 through V5 are the amplitudes of the 2nd- through 5th-order harmonics. +5V DVDD MAX1142 MAX1143 CREF REF REFADJ 1µF 2.2µF 0.22µF CS SCLK DIN DOUT RST SSTRB MC68HCXX I/O SCLK MOSI MISO I/O DGND AGND Spurious-Free Dynamic Range Spurious-free dynamic range (SFDR) is the ratio of RMS amplitude of the fundamental (maximum signal component), to the RMS value of the next largest distortion component. Chip Information TRANSISTOR COUNT: 21,807 PROCESS : BiCMOS Ordering Information (continued) PART TEMP. RANGE PINPACKAGE MAX1142AEAP -40°C to +85°C 20 SSOP MAX1142BEAP -40°C to +85°C 20 SSOP ±2 0°C to +70°C 20 SSOP ±1 MAX1143BCAP* 0°C to +70°C 20 SSOP ±2 MAX1143AEAP* -40°C to +85°C 20 SSOP ±1 MAX1143BEAP* -40°C to +85°C 20 SSOP ±2 MAX1143ACAP* *Future product—contact factory for availability. 18 ______________________________________________________________________________________ INL (LSB) ±1 14-Bit ADC, 200ksps, +5V Single-Supply with Reference AVDD AGND CREF 9kΩ MAX1142 MAX1143 REFERENCE REFADJ REF AIN INPUT SCALING NETWORK DAC COMPARATOR ANALOG TIMING CONTROL DVDD SSTRB DGND CS SCLK DIN RST SHDN SERIAL INPUT PORT MEMORY CALIBRATION ENGINE SERIAL OUTPUT PORT DOUT P2 P1 P0 CLOCK GENERATOR CONTROL ______________________________________________________________________________________ 19 MAX1142/MAX1143 Functional Diagram 14-Bit ADC, 200ksps, +5V Single-Supply with Reference SSOP.EPS MAX1142/MAX1143 Package Information Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 20 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2001 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.