TLP280,TLP280−4 TOSHIBA Photocoupler GaAs Ired & Photo−Transistor TLP280,TLP280−4 Programmable Controllers AC/DC−Input Module PC Card Modem (PCMCIA) Unit in mm TLP280 and TLP280−4 is a very small and thin coupler, suitable for surface mount assembly in applications such as PCMCIA fax modem, programmable controllers. TLP280 and TLP280−4 consist of photo transistor, optically coupled to two gallium arsenide infrared emitting diode connected inverse parallel, and can operate directly by AC input current • Collector−emitter voltage: 80 V (min) • Current transfer ratio: 50% (min) Rank GB: 100% (min) • Isolation voltage: 2500 Vrms (min) • UL recognized: UL1577, file No. E67349 • BSI approved: BS EN 60065: 2002, TOSHIBA Weight: 0.05 g (typ.) ― TOSHIBA Weight: 0.19 g (typ.) ― BS EN 60950-1: 2002 Certificate No. 8143, 8144 1 2007-10-01 TLP280,TLP280−4 Pin Configuration (top view) TLP280 TLP280-4 1 4 1 16 2 3 2 15 3 14 4 13 5 12 6 11 7 10 8 9 1 : Anode Cathode 2 : Cathode Anode 3 : Emitter 4 : Collector 1,3,5,7 : AnodeCathode 2,4,6,8 : Cathode Anode 9,11,13,15 : Emitter 10,12,14,16 : Collector 2 2007-10-01 TLP280,TLP280−4 Absolute Maximum Ratings (Ta = 25°C) Detector LED Characteristic Symbol Forward current IF(RMS) Forward current derating ΔIF /°C Rating TLP280 TLP280−4 ±50 −0.7 (Ta ≥ 53°C) Unit mA −0.5 (Ta ≥ 25°C) mA /°C Pulse forward current IFP ±1 (100μs pulse, 100pps) A Junction temperature Tj 125 °C Collector−emitter voltage VCEO 80 V Emitter−collector voltage VECO 7 V Collector current IC 50 mA Collector power dissipation (1 circuit) PC 150 100 mW ΔPC /°C −1.5 −1.0 mW /°C Collector power dissipation derating (Ta ≥ 25°C) (1 circuit) Junction temperature Tj 125 °C Storage temperature range Tstg −55~125 °C Operating temperature range Topr −55~100 °C Lead soldering temperature Tsol 260 (10s) °C Total package power dissipation (1 circuit) PT 200 170 mW Total package power dissipation derating (Ta ≥ 25°C) (1 circuit) ΔPT /°C −2.0 −1.7 mW /°C Isolation voltage (Note) BVS 2500 (AC, 1min., R.H.≤ 60%) Vrms Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). (Note): Device considered a two terminal device: LED side pins shorted together and detector side pins shorted together. 3 2007-10-01 TLP280,TLP280−4 Individual Electrical Characteristics (Ta = 25°C) Detector LED Characteristic Symbol Test Condition Min Typ Max Unit Forward voltage VF IF = ±10 mA 1.0 1.15 1.3 V Capacitance CT V = 0, f = 1 MHz ― 60 — pF Collector−emitter breakdown voltage V(BR) CEO IC = 0.5 mA 80 ― — V Emitter−collector breakdown voltage V(BR) ECO IE = 0.1 mA 7 ― — V ― 0.01 (2) 0.1 (10) μA ― 2 (4) 50 (50) μA ― 10 ― pF Collector dark current (Note 1) Capacitance (collector to emitter) ICEO CCE VCE = 48 V, Ambient light below (100 1x) VCE = 48 V, Ta = 85°C Ambient light below (100 1x) V = 0, f = 1 MHz (Note 1): Because of the construction, leak current might be increased by ambient light. Please use photocoupler with less ambient light. Coupled Electrical Characteristics (Ta = 25°C) Characteristic Current transfer ratio Saturated CTR Collector−emitter saturation voltage Off−state collector current CTR symmetry Symbol Test Condition MIn Typ. Max 50 — 600 100 — 600 Unit IC / IF IF = ±5 mA, VCE = 5 V Rank GB IC / IF (sat) IF = ±1 mA, VCE = 0.4 V Rank GB — 60 — 30 — — IC = 2.4 mA, IF = ±8 mA — — 0.4 IC = 0.2 mA, IF = ±1 mA Rank GB — 0.2 — — — 0.4 VF = ± 0.7 V, VCE = 48 V — — 10 μA 0.33 — 3 — VCE (sat) IC(off) IC (ratio) IC (IF = −5 mA) / IC (IF = 5 mA) (Note 2) % % V (Note 2): IF1 = 5V) I (I = I , V IC(ratio) = C2 F F2 CE IC1(IF = IF1, VCE = 5V) IC1 IC2 VCE IF2 4 2007-10-01 TLP280,TLP280−4 Isolation Characteristics (Ta = 25°C) Characteristic Symbol Capacitance input to output CS Isolation resistance RS Test Condition VS = 0V, f = 1 MHz VS = 500 V, R.H.≤ 60% BVS Typ. Max Unit — 0.8 — pF — Ω 5×10 AC, 1 minute Isolation voltage Min 10 10 14 2500 — — AC, 1 second, in oil — 5000 — DC, 1 minute, in oil — 5000 — Vdc Min Typ. Max Unit — 2 — — 3 — — 3 — — 3 — — 2 — — 25 — — 40 — Vrms Switching Characteristics (Ta = 25°C) Characteristic Symbol Rise time tr Fall time tf Turn−on time ton Turn−off time toff Turn−on time tON Storage time ts Turn−off time tOFF Test Condition VCC = 10 V, IC = 2 mA RL = 100Ω RL = 1.9 kΩ VCC = 5 V, IF = ±16 mA (Fig.1) μs μs (Fig. 1): Switching time test circuit IF RL VCC IF VCE VCE tON 5 tS VCC 4.5V 0.5V tOFF 2007-10-01 TLP280,TLP280−4 PC – Ta IF – Ta 100 200 160 Allowable collector power Dissipation PC (mW) Allowable forward current IF (mA) 80 60 TLP280 40 TLP280-4 20 0 -20-20 TLP280 120 TLP280-4 80 40 0 0 20 40 80 60 120 100 -20 20 0 Ambient temperature Ta (℃) 80 60 100 120 IF – VF IFP – DR 3000 40 Ambient temperature Ta (℃) 100 ≦100μs 1000 500 300 100 50 30 10 3 10−3 10−2 3 10−1 3 Duty cycle ratio 10 3 100℃ 75℃ 50℃ 25℃ 0℃ -25℃ -50℃ 1 0.8 DR 1.0 1.6 1.4 1.2 Forward voltage VF (V) IFP – VFP 1000 500 Pulse forward current IFP (mA) -2.8 -2.4 -2.0 -1.6 -1.2 -0.8 -0.4 0.1 10 0.1 0.6 0 ΔVF /ΔTa– IF -3.2 Forward voltage temperature coefficient ΔVF /ΔTa (mV/℃) (mA) Ta=25℃ Forward current IF Pulse forward current IFP (mA) PULSE WIDTH 0.3 0.5 1 3 Forward current IF 5 10 30 300 100 50 30 10 5 Pulse width≦10μs 3 Repetitive Frequency=100Hz 1 0.6 50 Ta=25℃ 1.0 1.4 1.8 Pulse forward voltage (mA) 6 2.2 2.6 3.0 VFP (V) 2007-10-01 TLP280,TLP280−4 IC – VCE = 25℃ 40 50 30 20 15 20 Ta 10 PC(MAX.) = 25℃ (mA) Ta 30 IC – VCE 30 25 Collector current IC Collector current IC (mA) 50 20 40 30 15 20 10 50 10 10 5 5 IF = 2mA IF = 5mA 0 0 0 5 Collector-emitter voltage 0 10 (mA) Collector dark current ID (ICEO) (μA) Collector current IC Sample A Sample B VCE (V) ICEO – Ta 101 10 10 1.0 Collector-emitter voltage VCE (V) IC – IF 100 0..5 0 10-1 VCE = 48V 24V 10-2 10V 5V 10-3 1 VCE = 10V 10-4 0 VCE = 5V VCE = 0.4V 0.1 0.1 1 10 Forward current IF 20 40 60 80 100 Ambient temperature Ta (℃) 100 (mA) IC / IF – IF 1000 Current transfer ratio IC / IF (%) VCE = 10V VCE = 5V Sample A VCE = 0.4V 100 Sample B 10 0.1 1 Forward current IF 10 100 (mA) 7 2007-10-01 TLP280,TLP280−4 IC – Ta VCE(sat) – Ta 0.24 100 25 (mA) 0.16 Collector current IC collector-Emitter saturation Voltage VCE(sat) (V) 0.20 0.12 0.08 0.04 10 10 5 1 1 IF = 0.5mA IF = 8mA, IC = 2.4mA IF = 1mA, IC = 0.2mA 0 -40-2 0 0.1 -20 100 50 VCE = 5V 0 Ambient temperature Ta (℃) 1000 100 50 Ambient temperature Ta (℃) Switching Time– RL Switching Time– Ta 100 Ta = 25℃ tOFF IF = 16mA VCC = 5V Switching time (μs) ts tOFF Switching time (μs) 100 10 tON 1 ts 0.1 -20 IF = 16mA VCC = 5V RL = 1.9kΩ 0 50 100 Ambient temperature Ta (℃) 10 tON 1 1 10 100 Load resistance RL (KΩ) 8 2007-10-01 TLP280,TLP280−4 RESTRICTIONS ON PRODUCT USE • Toshiba Corporation, and its subsidiaries and affiliates (collectively “TOSHIBA”), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively “Product”) without notice. • This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA’s written permission, reproduction is permissible only if reproduction is without alteration/omission. • Though TOSHIBA works continually to improve Product’s quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before creating and producing designs and using, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the “TOSHIBA Semiconductor Reliability Handbook” and (b) the instructions for the application that Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS’ PRODUCT DESIGN OR APPLICATIONS. • Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document. Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious public impact (“Unintended Use”). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this document. • Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. • Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. • The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. • ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. • GaAs (Gallium Arsenide) is used in Product. GaAs is harmful to humans if consumed or absorbed, whether in the form of dust or vapor. Handle with care and do not break, cut, crush, grind, dissolve chemically or otherwise expose GaAs in Product. • Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. • Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations. 9 2007-10-01