LTC4352 Low Voltage Ideal Diode Controller with Monitoring Features n n n n n n n n n n Description Low Loss Replacement for Power Diode Controls N-Channel MOSFET 0V to 18V Supply ORing or Holdup 0.5μs Turn-On and Turn-Off Time Undervoltage and Overvoltage Protection Open MOSFET Detect Status and Fault Outputs Hot Swappable Reverse Current Enable Input 12-Pin MSOP and DFN (3mm × 3mm) Packages n n n The LTC4352 regulates the forward voltage drop across the MOSFET to ensure smooth current transfer in diodeOR applications. A fast turn-on reduces the load voltage droop during supply switch-over. If the input supply fails or is shorted, a fast turn-off minimizes reverse currents. The controller operates with supplies from 2.9V to 18V. For lower voltages, an external supply is needed at the VCC pin. Power passage is disabled during undervoltage or overvoltage conditions. The controller also features an open MOSFET detect circuit that flags excessive voltage drop across the pass transistor in the on state. A REV pin enables reverse current, overriding the diode behavior when desired. Applications n The LTC®4352 creates a near-ideal diode using an external N-channel MOSFET. It replaces a high power Schottky diode and the associated heat sink, saving power and board area. The ideal diode function permits low loss power ORing and supply holdup applications. Redundant Power Supplies Supply Holdup Telecom Infrastructure Computer Systems and Servers L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and ThinSOT and PowerPath are trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Typical Application 2.9V to 18V Ideal Diode Power Dissipation vs Load Current 4.0 Si7336ADP CPO SOURCE VIN 0.1µF VCC UV GATE OUT STATUS LTC4352 OV REV FAULT GND 4352 TA01 *OPTIONAL 3.5 TO LOAD 0.1µF* MOSFET ON STATUS FAULT POWER DISSIPATION (W) 2.9V TO 18V 3.0 DIODE (SBG1025L) 2.5 2.0 POWER SAVED 1.5 1.0 0.5 0 MOSFET (Si7336ADP) 0 2 4 6 LOAD CURRENT (A) 8 10 4352 TA01b 4352fa 1 LTC4352 Absolute Maximum Ratings (Notes 1, 2) VIN, SOURCE Voltages....................................–2V to 24V VCC Voltage................................................... –0.3V to 7V OUT Voltage....................................................–2V to 24V CPO, GATE Voltages (Note 3)...................... –0.3V to 30V CPO D.C. Current....................................................10mA UV, OV, REV Voltages................................. –0.3V to 24V FAULT, STATUS Voltages............................. –0.3V to 24V FAULT, STATUS Currents...........................................5mA Operating Ambient Temperature Range LTC4352C................................................. 0°C to 70°C LTC4352I..............................................–40°C to 85°C LTC4352H........................................... –40°C to 150°C Storage Temperature Range................... –65°C to 150°C Lead Temperature (Soldering, 10 sec) MS Package....................................................... 300°C Pin Configuration TOP VIEW TOP VIEW VIN 1 12 SOURCE VCC 2 11 GATE UV 3 OV 4 STATUS 5 8 OUT FAULT 6 7 REV 13 VIN VCC UV OV STATUS FAULT 10 CPO 9 GND 1 2 3 4 5 6 12 11 10 9 8 7 SOURCE GATE CPO GND OUT REV MS PACKAGE 12-LEAD PLASTIC MSOP DD PACKAGE 12-PIN (3mm × 3mm) PLASTIC DFN TJMAX = 150°C, θJA = 43°C/W EXPOSED PAD (PIN 13) PCB GND CONNECTION OPTIONAL TJMAX = 150°C, θJA = 164°C/W Order Information LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC4352CDD#PBF LTC4352CDD#TRPBF LDPJ 12-Pin (3mm × 3mm) Plastic DFN 0°C to 70°C LTC4352IDD#PBF LTC4352IDD#TRPBF LDPJ 12-Pin (3mm × 3mm) Plastic DFN –40°C to 85°C LTC4352HDD#PBF LTC4352HDD#TRPBF LDPJ 12-Pin (3mm × 3mm) Plastic DFN –40°C to 150°C LTC4352CMS#PBF LTC4352CMS#TRPBF 4352 12-Lead Plastic MSOP 0°C to 70°C LTC4352IMS#PBF LTC4352IMS#TRPBF 4352 12-Lead Plastic MSOP –40°C to 85°C LTC4352HMS#PBF LTC4352HMS#TRPBF 4352 12-Lead Plastic MSOP –40°C to 150°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 4352fa 2 LTC4352 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VIN = 12V, VSOURCE = VIN, VOUT = VIN, VCC Open, unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Supplies VIN Input Operating Range l l l 2.9 0 0 18 VCC 18 V V V VCC(EXT) VCC External Supply Range l 2.9 6 V VCC(INT) VCC Internal Regulator Voltage l 3.5 4.1 4.7 V IIN VIN Supply Current ICC With External 2.9V to 4.7V VCC Supply With External 4.7V to 6V VCC Supply VIN = 0V, VCC = 5V, VOUT = 18V VIN = 0V, VCC = 5V, VOUT = 18V (LTC4352H) l l l 1.4 –10 –10 3 –13 –25 mA µA µA External VCC Supply Current VCC = 5V, VIN = 0V l 1.25 2.5 mA VCC(UVLO) VCC Undervoltage Lockout Threshold VCC Rising l 2.45 2.57 2.7 V ΔVCC(HYST) VCC Undervoltage Lockout Hysteresis l 50 70 90 mV l 10 25 40 mV 5 6.1 7.5 V Ideal Diode Control VFWD(REG) Forward Regulation Voltage (VIN − VOUT) ΔVGATE MOSFET Gate Drive (VGATE – VSOURCE) VFWD = 0.1V, I = 0 and –1μA l tON(GATE) GATE Turn-On Delay CGATE = 10nF, VFWD = 0.2V l 0.25 0.5 µs tOFF(GATE) GATE Turn-Off Delay CGATE = 10nF, VFWD = −0.2V l 0.2 0.5 µs VUV Falling, VOV Rising l 490 500 510 mV l 2.5 5 8.5 mV (LTC4352H) l l 0.8 0.8 1.0 1.0 1.2 1.25 V V 0 ±1 µA 10 13 µA 200 µA Input/Output Pins VUV,OV(TH) UV, OV Threshold Voltage ΔVUV,OV(HYST) UV, OV Threshold Hysteresis VREV(TH) REV Threshold Voltage IUV,OV UV, OV Current V = 0.5V l IREV REV Current VREV = 1V l 7 IOUT OUT Current VOUT = 0V, 12V l –13 ISOURCE SOURCE Current VSOURCE = 0V l ICPO(UP) CPO Pull-Up Current VCPO = VIN = 2.9V VCPO = VIN = 18V l l IGATE GATE Fast Pull-Up Current GATE Fast Pull-Down Current GATE Off Pull-Down Current VFWD = 0.2V, ∆VGATE = 0V, VCPO = 17V VFWD = –0.2V, ∆VGATE = 5V VUV = 0V, ∆VGATE = 2.5V l IFLT,STAT(IN) STATUS, FAULT Leakage Current V = 18V l IFLT,STAT(UP) STATUS, FAULT Pull-Up Current V = 0V l VOL STATUS, FAULT Output Low Voltage I = 1.25mA l –85 –130 µA –60 –50 –90 –75 –115 –100 µA µA 60 –1.5 1.5 100 145 A A µA 0 ±1 µA –10 –12 µA 0.2 0.4 V –8 VOH STATUS, FAULT Output High Voltage I = –1μA l VCC – 1 VCC – 0.5 ΔVGATE(ST) MOSFET On Detect Threshold STATUS Pulls Low, VFWD = 50mV STATUS Pulls Low, VFWD = 50mV (LTC4352H) l l 0.3 0.28 0.7 0.7 1.1 1.1 V V VFWD(FLT) Open MOSFET Threshold (VIN – VOUT) FAULT Pulls Low l 200 250 300 mV Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating for extended periods may affect device reliability and lifetime. Note 2: All currents into device pins are positive; all currents out of device V pins are negative. All voltages are referenced to GND unless otherwise specified. Note 3: Internal clamps limit the GATE and CPO pins to a minimum of 5V above, and a diode below SOURCE. Driving these pins to voltages beyond the clamp may damage the device. 4352fa 3 LTC4352 Typical Performance Characteristics TA = 25°C, VIN = 12V, VSOURCE = VIN, VOUT = VIN, VCC Open, unless otherwise noted. VIN Current vs Voltage 300 1.6 VIN Current vs Voltage with External VCC VCC Current vs Voltage 1.50 VCC = 5V 250 1.25 200 0.8 1.00 150 ICC (mA) IIN (µA) IIN (mA) 1.2 100 0.25 0 0 3 6 9 VIN (V) 12 15 –50 18 3 0 5 4 VIN (V) OUT Current vs Voltage 250 6 VCPO –VSOURCE (V) 100 50 VIN = 18V 4 VIN = 2.9V 3 3 6 9 15 12 VOUT (V) 18 2 –1 4 5 6 4352 G03 VOUT = VIN – 0.1V 6 VIN = 18V 5 4 VIN = 2.9V 3 2 1 0 0 3 VCC (V) GATE Voltage vs Current 1 0 2 1 7 5 150 0 4352 G02 CPO Voltage vs Current 7 200 IOUT (µA) 2 1 4352 G01 300 –50 0 VGATE –VSOURCE (V) 0 0.75 0.50 50 0.4 VIN = 0V 0 0 –40 –20 4352 G04 –100 –60 –80 ICPO (µA) –120 –1 0 –40 –20 4352 G05 STATUS, FAULT Output Low Voltage vs Current –60 –80 IGATE (µA) –100 –120 4352 G06 STATUS, FAULT Output High Voltage vs Current 4.0 1 3.5 3.0 2.5 0.6 VOH (V) VOL (V) 0.8 0.4 2.0 1.5 1.0 0.2 0.5 0 0 1 2 3 CURRENT (mA) 4 5 4352 G07 0 0 –2 –4 –6 –8 CURRENT (µA) –10 –12 4352 G08 4352fa 4 LTC4352 Pin Functions VIN (Pin 1): Voltage Sense and Supply Input. Connect this pin to the power input side of the MOSFET. The low voltage supply VCC is generated from VIN. The voltage sensed at this pin is used to control the MOSFET gate. VCC (Pin 2): Low Voltage Supply. Connect a 0.1μF capacitor from this pin to ground. When VIN ≥ 2.9V, this pin provides decoupling for an internal regulator that generates a 4.1V supply. For applications where VIN < 2.9V, connect an external supply voltage in the range 2.9V to 6V to this pin. UV (Pin 3): Undervoltage Comparator Input. Connect this pin to an external resistive divider from VIN. If the voltage at this pin falls below 0.5V, an undervoltage fault is detected and the MOSFET is turned off. The comparator has a built-in hysteresis of 5mV. Tie to VCC if unused. OV (Pin 4): Overvoltage Comparator Input. Connect this pin to an external resistive divider from VIN. If the voltage at this pin rises above 0.5V, an overvoltage fault is detected and the MOSFET is turned off. The comparator has a built-in hysteresis of 5mV. Tie to GND if unused. STATUS (Pin 5): MOSFET Status Output. This pin is pulled low by an open-drain output when the external MOSFET is on. An internal 10µA current source pulls this pin up to a diode below VCC. It may be pulled above VCC using an external pull-up. Tie to GND or leave open if unused. FAULT (Pin 6): Fault Output. This pin is pulled low by an open-drain output when a fault occurs. This fault could either be an undervoltage fault, an overvoltage fault, or an open MOSFET fault. The external MOSFET is turned off for undervoltage and overvoltage faults, while it is left on for open MOSFET fault. An internal 10µA current source pulls this pin up to a diode below VCC. It may be pulled above VCC using an external pull-up. Tie to GND or leave open if unused. REV (Pin 7): Reverse Current Enable Input. Connect this pin to GND for normal diode operation that blocks reverse current. Driving this pin above 1V fully turns on the MOSFET gate to allow reverse current. An internal 10µA current source pulls this pin to GND. OUT (Pin 8): Output Voltage Sense Input. Connect this pin to the output side of the MOSFET. The voltage sensed at this pin is used to control the MOSFET gate. GND (Pin 9): Device Ground. CPO (Pin 10): Charge Pump Output. Connect a capacitor from this pin to the SOURCE pin. The value of this capacitor is approximately 10x the gate capacitance (CISS) of the MOSFET switch. The charge stored on this capacitor is used to pull-up the gate during a fast turn-on. Leave this pin open if fast turn-on is not needed. GATE (Pin 11): MOSFET Gate Drive Output. Connect this pin to the gate of the external N-channel MOSFET switch. An internal clamp limits the gate voltage to 6.1V above, and a diode below SOURCE. During fast turn-on a 1.5A pull-up charges GATE to CPO. During fast turn-off a 1.5A pull-down discharges GATE to SOURCE. SOURCE (Pin 12): MOSFET Gate Drive Return. Connect this pin to the source of the external N-channel MOSFET switch. EXPOSED PAD (Pin 13, DD Package Only): Exposed pad may be left open or connected to device ground. 4352fa 5 LTC4352 Functional Diagram VCC VIN CPO 2 1 10 CHARGE PUMP f = 3MHz VCC 100µA 4.1V + LDO + GATE OFF – – ENABLE REVERSE CURRENT + – VIN – 25mV DISABLE LDO VCC LOW + – 2.57V CP5 UV FAULT SOURCE CP2 – OV 4 1V 8 OUT 7 REV 5 STATUS 6 FAULT 10µA VCC 10µA + CP6 M1 – VCC OPEN MOSFET DETECT 0.5V + + – GATE – + 12 SOURCE CP3 0.7V UV 3 + – + CP4 11 GATE AMP 10µA OV FAULT M2 CP1 Z *DD PACKAGE ONLY 9 13 GND EXPOSED PAD* 4352 FD 4352fa 6 LTC4352 Operation The LTC4352 controls either single or back-to-back N-channel MOSFETs in order to emulate an ideal diode. Dual MOSFETs eliminate current flow from the input to the output in an input undervoltage or overvoltage condition. When enabled, an amplifier (AMP) monitors the voltage between the VIN and OUT pins, and drives the GATE pin. The amplifier controls the gate of the external MOSFET to servo its forward voltage drop (VIN – OUT) to 25mV. The gate voltage rises to enhance the MOSFET if the load current causes more than 25mV of drop. For large output currents the MOSFET gate is driven fully on and the voltage drop is equal to ILOAD • RDS(ON). In the case of an input supply short-circuit, when the MOSFET is conducting, a large reverse current starts flowing from the load towards the input. The AMP detects this failure condition as soon as it appears, and turns off the MOSFET by pulling down the GATE pin. The REV pin can be used to allow reverse current, overriding the diode behavior. The AMP quickly pulls-up the GATE pin whenever it senses a large forward voltage drop. An external capacitor between the CPO and SOURCE pins is needed for fast gate pull-up. This capacitor is charged up, at device power-up, by the internal charge-pump. This stored charge is used for the fast gate pull-up. limit the GATE to SOURCE voltage to 6.1V, and the CPO to SOURCE voltage to 6.7V. The same clamps also limit the CPO and GATE pins to a diode voltage below the SOURCE pin. OV, UV, and VCC comparators, CP1 to CP3, control power passage. The MOSFET is held off whenever the OV pin is above 0.5V, the UV pin is below 0.5V, or the VCC pin is below 2.57V. There is a 40µs delay from all three conditions becoming good to GATE being allowed to turn on. Overvoltage causes a fast turn-off, while undervoltage activates a 100μA pull-down on GATE after a 7μs delay. Open-drain pull-down, M1, pulls the STATUS pin low when the GATE to SOURCE voltage exceeds 0.7V, to indicate that power is passing through the MOSFET. The FAULT output, M2, pulls low during an undervoltage or overvoltage fault condition. It also pulls low when GATE is fully on and the forward voltage drop exceeds 250mV, indicating the MOSFET has too much current or has failed open circuit. Note that this open MOSFET fault does not turn off the MOSFET unlike the undervoltage and overvoltage faults. LDO is a low dropout regulator that generates a 4.1V supply at the VCC pin from the VIN input. When a supply below 2.9V is being ORed, an external supply in the 2.9V to 6V range is required at the VCC pin. Comparator CP4 will disable LDO when VIN is below VCC. The GATE pin sources current from the CPO pin, and sinks current to the SOURCE and GND pins. Internal clamps 4352fa 7 LTC4352 Applications Information common supply voltage it turns off the MOSFET, thereby matching the function and performance of an ideal diode. High availability systems often employ parallel-connected power supplies or battery feeds to achieve redundancy and enhance system reliability. ORing diodes have been a popular means of connecting these supplies at the point of load. Diodes with storage capacitors also hold up supply voltages when an input voltage sags or has a brownout. The disadvantage of these approaches is the diode’s significant forward voltage drop and the resulting power loss. Additionally, diodes provide no information concerning the status of the sourcing supply. Separate control must therefore be added to ensure that a supply that is out of range is not allowed to affect the load. Power Supply Configuration The LTC4352 can operate with supplies down to 0V. This requires powering the VCC pin with an always present external supply in the 2.9V to 6V range. If not always present, a series 470Ω resistor or Schottky diode limits device power dissipation and backfeeding of low VCC supply when VIN is high. For a 2.9V to 4.7V VCC supply, VIN should be lower than VCC. A 0.1µF bypass capacitor should also be connected between the VCC and GND pins, close to the device. Figure 2 illustrates this. The LTC4352 solves these problems by using an external N-channel MOSFET as the pass element (see Figure 1). The MOSFET is turned on when power is being passed, allowing for a low voltage drop from the supply to the load. When the input source voltage drops below the output If VIN operates above 2.9V then the external supply at VCC is not needed. The 0.1µF capacitor is still required for bypassing. Q1 Si7336ADP TO LOAD 12V C2 R4 2.7k 0.1µF CPO SOURCE VIN C1 0.1µF GATE OUT D1 MOSFET ON D2 STATUS VCC UV LTC4352 OV FAULT FAULT REV R5 2.7k D1: GREEN LED LN1351C D2: RED LED LN1261CAL GND 4352 F01 Figure 1. 12V Ideal Diode with Status and Fault Indicators TO LOAD 2.9V TO 18V VIN VCC 0.1µF GATE LTC4352 GND OUT TO LOAD 0V TO VCC 2.9V TO 4.7V VIN VCC 0.1µF GATE OUT LTC4352 GND TO LOAD 0V TO 18V 4.7V TO 6V VIN VCC 0.1µF GATE OUT LTC4352 GND 4352 F02 Figure 2. Power Supply Configurations 4352fa 8 LTC4352 APPLICATIONS INFORMATION CPO and GATE Start-Up In single MOSFET applications, CPO is initially pulled up to a diode below the SOURCE pin (Figure 3). In back-toback MOSFET applications, CPO starts off at 0V, since SOURCE is near ground (Figure 4). CPO starts ramping up 10µs after VCC clears its undervoltage lockout level. Another 40µs later, GATE will also start ramping up with CPO if UV, OV and VIN – OUT conditions allow it to. The ramp rate is decided by the CPO pull-up current into the combined CPO and GATE pin capacitances. An internal clamp limits the CPO voltage to 6.7V above SOURCE, while the final GATE voltage is determined by the forward drop servo amplifier. MOSFET Selection The LTC4352 drives N-channel MOSFETs to conduct the load current. The important features of the MOSFET are its threshold voltage, the maximum drain-source voltage BVDSS, and the on-resistance RDS(ON). The gate drive for the MOSFET is guaranteed to be between 5V and 7.5V. This allows the use of logic level threshold VIN = 5V C2 = 0.1µF N-channel MOSFETs. The maximum allowable drain-source voltage, BVDSS, must be higher than the supply voltages as the full supply voltage can appear across the MOSFET when the input falls to 0V. The FAULT pin pulls low to signal an open MOSFET fault whenever the forward voltage drop across the enhanced MOSFET exceeds 250mV. The RDS(ON) should be small enough to conduct the maximum load current while not triggering such a fault (when using FAULT), and to stay within the MOSFET’s power rating at the maximum load current. CPO Capacitor Selection The recommended value of the capacitor between the CPO and SOURCE pins is approximately 10x the input capacitance, CISS, of the MOSFET. A larger capacitor takes a correspondingly longer time to charge up by the internal charge pump. A smaller capacitor suffers more voltage drop during a fast gate turn-on event as it shares charge with the MOSFET gate capacitance. VIN = 5V C2 = 0.1µF CPO GATE CPO GATE OUT VOLTAGE (5V/DIV) VOLTAGE (5V/DIV) OUT VIN, SOURCE VIN VCC VCC TIME (2.5ms/DIV) 4352 FO3 Figure 3. Start-up Waveform for Single MOSFET Application TIME (2.5ms/DIV) 4352 FO4 Figure 4. Start-up Waveform for Back-to-Back MOSFET Application 4352fa 9 LTC4352 Applications Information Undervoltage and Overvoltage Protection Inrush Control Unlike a regular diode, the LTC4352 can prevent out of range input voltages from affecting the load voltage. This requires back-to-back MOSFETs, and resistive dividers from the input to the UV and OV pins. For an example, see Figure 5. The LTC4352 can be used for inrush control in applications where the input supply is hot-plugged. See Figure 6. The CPO capacitor is omitted, since fast turn-on with stored charge is not desired here. Undervoltage holds the gate off till the short pin makes contact. 40µs after the UV level is satisfied, the MOSFET gate ramps up due to the CPO pull-up current. A RC network on the gate further slows down the output dV/dt, while allowing fast turn-off during reverse current or overvoltage conditions. Resistor RG prevents high frequency oscillations in Q2. A dedicated hot swap controller may be needed if overcurrent protection is also desired. MOSFET Q2 is required to block conduction through the body diode of Q1 when its gate is held off. The resistive dividers set up the input voltage range where the ideal diode control is allowed to operate. Outside this range, the gate is held off and the FAULT pin pulls low. When using a CPO capacitor in circuit with back-to-back MOSFETs, there will be a large inrush current to the load capacitance due to the fast gate turn-on after UV, OV levels are met. Without the capacitor, the inrush will depend on the CPO pull-up current charging up the gate capacitance. Q2 Si7336ADP Q1 Si7336ADP 12V Q2 Si7336ADP 5V Z1 Q1 Si7336ADP CG 0.1µF 0.15µF 105k R3 5.11k R2 C2 31.6k 1% R3 1k 1% R2 VIN CPO SOURCE UV 3.09k 1% OV R1 GND VIN SOURCE GATE OUT UV GATE OUT FAULT VCC CPO LTC4352 OV STATUS LTC4352 RG 10Ω R6 10k TO LOAD TO LOAD NC GND 4352 F06 C1 0.1µF REV GND BACKPLANE Z1: DIODES INC. SMAJ12A CONNECTORS PLUG-IN CARD 4352 F05 Figure 5. 5V Ideal Diode with UV and OV Protection Figure 6. Inrush and Ideal Diode Control on a Hot Swap Card 4352fa 10 LTC4352 Applications INFORMATION External CPO Supply Design Example The internal charge pump takes milliseconds to charge up the CPO pin capacitor especially during device power up. This time can be shortened by connecting an external supply to the CPO pin. A series resistor is needed to limit the current into the internal clamp between the CPO and SOURCE pins. The CPO supply should also be higher than the main input supply to meet the gate drive requirements of the MOSFET. Figure 7 shows such a 5V ideal diode application, where a 12V supply is connected to the CPO pin through a 1k resistor. The 1k limits the current into the CPO pin to 5.3mA, when the SOURCE pin is grounded. The following design example demonstrates the calculations involved for selecting components in a 12V system with 10A maximum load current (see Figure 1). First, calculate the RDS(ON) of the MOSFET to achieve the desired forward drop at full load. Assuming a VFWD of 50mV (which is comfortably below the 200mV minimum open MOSFET fault threshold): When the capacitances at the input and output are very small, rapid changes in current can cause transients that exceed the 24V Absolute Maximum Rating of the VIN and OUT pins. In ORing applications using a single MOSFET, one surge suppressor connected from OUT to ground clamps all the inputs. In the absence of a surge suppressor, an output capacitance of 10μF is sufficient in most applications to prevent the transient from exceeding 24V. Back-to-back MOSFET applications, depending on voltage levels, may require a surge suppressor on each supply input. P = I2LOAD • RDS(ON) = (10A)2 • 4mΩ = 0.4W With a maximum steady-state thermal resistance, θJA, of 65°C/W, 0.4W causes a modest 26°C rise in junction temperature of the Si7336ADP above the ambient. The input capacitance, CISS, of the Si7336ADP is about 6500pF. Slightly exceeding the 10x recommendation, a 0.1µF capacitor is selected for C2. Q1 Si7336ADP 5V VIN 12V SOURCE C2 0.1µF CPO VFWD 50mV = = 5mΩ ILOAD 10A The Si7336ADP offers a good solution, in a SO-8 sized package, with a maximum RDS(ON) of 4mΩ and BVDSS of 30V. The maximum power dissipation in the MOSFET is: Input Transient Protection R7 1k RDS (ON) ≤ GATE TO LOAD OUT LTC4352 GND 4352 F07 Figure 7. 5V Ideal Diode with External 12V Powering CPO for Faster Start-up and Refresh 4352fa 11 LTC4352 Applications INFORMATION LEDs, D1 and D2, require around 3mA for good luminous intensity. Accounting for a 2V diode drop and 0.5V VOL, R1 and R2 are set to 2.7k. PCB Layout Considerations Connect the VIN and OUT pin traces as close as possible to the MOSFET’s terminals. Keep the traces to the MOSFET wide and short to minimize resistive losses. The PCB traces D S D S D G D W TO LOAD 8 OUT 7 9 GND 10 11 VIA TO GROUND PLANE GATE TRACK WIDTH W: 0.03˝ PER AMPERE ON 1OZ CU FOIL CURRENT FLOW S SOURCE 12 W It is also important to put C1, the bypass capacitor for the VCC pin, as close as possible between VCC and GND. Also place C2 near the CPO and SOURCE pins. Surge suppressors, when used, should be mounted close to the LTC4352 using short lead lengths. Q1 SO-8 CURRENT FLOW FROM INPUT SUPPLY associated with the power path through the MOSFET should have low resistance. See Figure 8. C1 MSOP-12 6 5 4 3 VCC 2 1 VIN LTC4352 VIA TO GROUND PLANE 4352 F08 DRAWING IS NOT TO SCALE! Figure 8. Recommended PCB Layout for Power MOSFET 4352fa 12 LTC4352 Typical Applications Plug-in Card Supply Holdup Using Ideal Diode at Input Q1 Si7336ADP HOT SWAP CONTROLLER 12V SOURCE VIN GATE TO LOAD + OUT CHOLDUP LTC4352 GND GND BACKPLANE GND CONNECTORS 4352 TA02 PLUG-IN CARD Ideal Diode with Reverse Input Protection Q1 Si4438DY 3.5V TO 9V 10A LOAD 0.1µF D3 1N4148 OR BAT85 CPO SOURCE VIN GATE VCC C1 0.1µF UV D5 SMAJ17A LTC4352 OV REV OUT STATUS FAULT GND D4 BAT85 4352 TA04 4352fa 13 LTC4352 Package Description DD Package 12-Lead Plastic DFN (3mm × 3mm) (Reference LTC DWG # 05-08-1725 Rev A) R = 0.115 TYP 7 0.40 ± 0.10 12 0.70 ±0.05 3.50 ±0.05 2.10 ±0.05 2.38 ±0.05 1.65 ±0.05 2.38 ±0.10 3.00 ±0.10 (4 SIDES) 1.65 ± 0.10 6 1 0.23 ± 0.05 0.45 BSC 0.75 ±0.05 0.200 REF 0.25 ± 0.05 PIN 1 NOTCH R = 0.20 OR 0.25 × 45° CHAMFER PIN 1 TOP MARK (SEE NOTE 6) PACKAGE OUTLINE 0.45 BSC 2.25 REF 2.25 REF RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 0.00 – 0.05 (DD12) DFN 0106 REV A BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD AND TIE BARS SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE MS Package 12-Lead Plastic MSOP (Reference LTC DWG # 05-08-1668 Rev Ø) 4.039 ± 0.102 (.159 ± .004) (NOTE 3) 0.889 ± 0.127 (.035 ± .005) 5.23 (.206) MIN 12 11 10 9 8 7 0.254 (.010) 3.20 – 3.45 (.126 – .136) DETAIL “A” 3.00 ± 0.102 (.118 ± .004) (NOTE 4) 4.90 ± 0.152 (.193 ± .006) 0° – 6° TYP 0.406 ± 0.076 (.016 ± .003) REF GAUGE PLANE 0.42 ± 0.038 (.0165 ± .0015) TYP 0.53 ± 0.152 (.021 ± .006) 0.65 (.0256) BSC RECOMMENDED SOLDER PAD LAYOUT DETAIL “A” 0.18 (.007) SEATING PLANE 1.10 (.043) MAX 0.22 – 0.38 (.009 – .015) TYP 1 2 3 4 5 6 0.650 (.0256) BSC NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 0.86 (.034) REF 0.1016 ± 0.0508 (.004 ± .002) MSOP (MS12) 1107 REV Ø 4352fa 14 LTC4352 Revision History REV DATE DESCRIPTION PAGE NUMBER A 12/10 Added H-grade information 2,3 Revised FAULT pin description in Pin Functions 5 Revised Functional Diagram 6 Added text to Operation section 7 Revised Figures 2, 5, 6 in Applications Information 8, 10 Added new Typical Application 13 Revised Typical Application and Related Parts list 16 4352fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 15 LTC4352 Typical Application 0V to 18V Ideal Diode-OR VIN1 0V TO 18V 5V Si7336ADP CPO SOURCE VIN GATE VCC 0.1µF LTC4352 OV FAULT REV 5V GND Si7336ADP 0.1µF CPO SOURCE VIN GATE OUT VCC 0.1µF OUT STATUS UV VIN2 0V TO 18V TO LOAD 0.1µF UV STATUS LTC4352 OV REV FAULT GND 4352 TA03 Related Parts PART NUMBER DESCRIPTION COMMENTS LTC1473/LTC1473L Dual PowerPath™ Switch Driver N-Channel, 4.75V to 30V/3.3V to 10V, SSOP-16 LTC1479 PowerPath Controller for Dual Battery Systems Three N-Channel Drivers, 6V to 28V, SSOP-36 LTC4350 Hot Swappable Load Share Controller N-Channel, 1.5V to 12V, Share Bus, SSOP-16 LTC4354 Negative Voltage Diode-OR Controller and Monitor Dual N-Channel, –4.5V to –80V, SO-8, DFN-8 LTC4355 Positive High Voltage Ideal Diode-OR and Monitor Dual N-Channel, 9V to 80V, SO-16, DFN-14 LTC4357 Positive High Voltage Ideal Diode Controller N-Channel, 9V to 80V, MSOP-8, DFN-6 LTC4358 5A Ideal Diode Internal N-Channel, 9V to 26.5V, TSSOP-16, DFN-14 LTC4411 2.6A Low Loss Ideal Diode in ThinSOT™ Internal P-Channel, 2.6V to 5.5V, 40μA IQ, SOT-23 LTC4412/LTC4412HV Low Loss PowerPath Controller in ThinSOT P-Channel, 2.5V to 28V/36V, 11μA IQ, TSOT-23 LTC4413/LTC4413-1 Dual 2.6A, 2.5V to 5.5V, Ideal Diodes in DFN-10 Dual Internal P-Channel, 2.5V to 5.5V, DFN-10 LTC4414 36V Low Loss PowerPath Controller for Large PFETs P-Channel, 3V to 36V, 30μA IQ, MSOP-8 LTC4416/LTC4416-1 36V Low Loss Dual PowerPath Controller for Large PFETs Dual P-Channel, 3.6V to 36V, 70μA IQ, MSOP-10 4352fa 16 Linear Technology Corporation LT 1210 REV A • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com LINEAR TECHNOLOGY CORPORATION 2008