APITECH SF0190BA03154S

190 MHz SAW Filter
8 MHz Bandwidth
Part Number: SF0190BA03154S
DESCRIPTION
•
•
•
190 MHz SAW bandpass filter with 8 MHz bandwidth.
13.3 x 6.5 mm ceramic LCC package.
RoHS compliant.
TYPICAL PERFORMANCE
Horizontal:
Vertical (from top):
S11 (160-220 MHz)
Frequency
Magnitude
Magnitude
Phase Deviation
Group Delay Deviation
6
10
1
10
100
MHz /div
dB/div
dB/div
deg/div
ns/div
S22 (160-220 MHz)
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0190BA03154S Rev A
ECN 36650
19-Mar-2010
Page 1 of 3
190 MHz SAW Filter
8 MHz Bandwidth
Part Number: SF0190BA03154S
SPECIFICATION
Parameter 2
Center Frequency (Fc) 1
Insertion Loss
1 dB Bandwidth
3 dB Bandwidth
30 dB Bandwidth
Rejection (100 to 180 MHz)
Rejection (200 to 275 MHz)
Passband Ripple (186 to 194 MHz)
Phase Linearity (186 to 194 MHz)
Group Delay Deviation (186 to 194 MHz)
Absolute Delay
Temperature Coefficient of Fc
Source and Load Impedance 3
Notes:
Min
189.6
8
10
40
40
-
Typ
190
12.9
9.36
10.21
12.7
48
48
0.6
2.5
40
0.94
-18
50
Max
190.4
14
15
1.0
15
120
-
Units
MHz
dB
MHz
MHz
MHz
dB
dB
dB p-p
deg p-p
ns p-p
us
ppm/˚C
Ω
1. All parameters are based upon matching circuit.
2. All parameters are evaluated at ambient temperature only.
3. Optimum impedance in order to achieve performance shown.
MAXIMUM RATINGS
Parameter
Storage Temperature Range
Input Power Level
Min
-40
-
Max
85
+13
Units
˚C
dBm
MATCHING CIRCUIT
11
Input
50 Ω
Single-ended
All other pads
GND
Typical component values:
5
Ls1 = 68 nH
Cp1 = 39 pF
Output
50 Ω
Single-ended
GND
Ls2 = 62.8 nH
Cp2 = 39 pF
Notes:
1. Recommend +/-2% tolerance matching components. Typical inductor Q=40.
2. Tuning values shown are for reference only. Optimum values may change depending upon board layout.
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0190BA03154S Rev A
ECN 36650
19-Mar-2010
Page 2 of 3
190 MHz SAW Filter
8 MHz Bandwidth
Part Number: SF0190BA03154S
PACKAGE OUTLINE
SUGGESTED FOOTPRINT
Units: mm
Tolerances are ±0.15 mm except
where indicated.
Pad Configuration:
Input:
11
Output:
5
Ground:
All other pads
Package Material:
Body: Al2O3 ceramic
Lid: Kovar, Ni plated
Terminations: Au plating 1 µm
min, over a 1.3-8.9 µm Ni plating
ISO 9001
Registered
All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice.
© 2010 All rights reserved.
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0190BA03154S Rev A
ECN 36650
19-Mar-2010
Page 3 of 3