MASW-001150-1316 SURMOUNT PIN Diode Switch Element with Thermal Terminal V5 Features Specified Bandwidth: 45MHz—2.5GHz Useable 30MHz to 3.0GHz Low Loss <0.5dB High isolation >40dB High C.W. Incident Power, 50W at 500MHz High Input IP3, +66dBm @ 500MHz Unique Thermal Terminal for Series Diode Surface Mount Device (No Wire Bonds) Rugged Silicon-Glass Construction Silicon Nitride Passivation Protective Polymer Protective Polymer Scratch Protection RoHS Compliant Description A PIN diode series-shunt switch element with a unique integrated thermal terminal for dissipating heat in the series diode created by the DC and RF input power. The thermal terminal allows for optimum heat dissipation by providing a direct thermal connection between the series diode and the circuit heatsink while also being electrically isolated. The chip is designed to provide a heat transfer conduit that does not interfere with the PIN diode anode (input) and cathode (output) electrical terminals, especially with respect to RF performance. The chip is fabricated using M/A-COM Technology Solutions patented HMIC™ process and features silicon pedestals embedded in a low loss, low dispersion glass for low leakage current. The topside is fully encapsulated with silicon nitride and has an additional polymer layer to protect against damage during handling and assembly. Applications This PIN diode series-shunt switch element is particularly advantageous in high average power, 50W, switch applications from 30MHZ – 3GHz. The backside RF, D.C., and thermal I/O ports allow for direct solder re-flow, surface mount, attachment to a micro-strip circuit assembly. The thermal terminal design provides the, power dissipating, series diode a direct connection to the circuit thermal ground for unprecedented heat transfer. The thermal terminal port is electrically isolated from the I/O ports and can be configured as either a reflective or an absorptive switch. 1 Ordering Information 2 Part Number Package MASW-001150-13160W WAFFLE PACK MASW-001150-13160P POCKET TAPE 2. Reference Application Note M513 for reel size information. Absolute Maximum Ratings Parameter Absolute Maximum Forward Current 100mA Reverse Voltage - 180V Operating Temperature -55°C to +125°C Storage Temperature -55°C to +150°C Junction Temperature +175°C Dissipated RF & DC Power 500MHz, 4W RF C.W. Incident Power 500MHz, 50W Mounting Temperature +260°C for 30 seconds ESD Class 1A — HBM ESD Class M3 — MM ESD Class C3 — CDM ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, • India Tel: +91.80.43537383 • China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-001150-1316 SURMOUNT PIN Diode Switch Element with Thermal Terminal V5 Electrical Specifications @ TAMB = +25°C Symbol Parameter Conditions Units Typical Maximum -25V ,30MHz -25V, 1800MHz -25V, 30MHz -25V, 1800MHz pF pF pF pF 0.52 0.37 0.54 0.39 — — — — CT Series CT Series CT Shunt CT Shunt Total Capacitance Total Capacitance Total Capacitance Total Capacitance RS Series Series Resistance 20mA, 30MHz 1.13 — RS Series Series Resistance 20mA,1800MHz 1.25 — RS Series Series Resistance 50mA, 30MHz 0.93 — RS Series Series Resistance 50mA,1800MHz 1.07 — RS Shunt Series Resistance 10mA, 30MHz 1.00 — RS Shunt Series Resistance 10mA, 1800MHz 0.99 — VF Forward Voltage 20mA V 0.82 0.85 VF Forward Voltage 50mA V 0.88 0.90 -180V µA — -10.0 IR Reverse Leakage Current RqJL Thermal Resistance Steady State °C/W 36.0 — Minority Carrier Lifetime IF 10mA/IR-6mA µs 8.5 — 1 TL 1. Measured from 50% of control voltage to 90% of output voltage Parameter Units Insertion Loss 2 dB Port 1 Port 2 Conditions Minimum Typical Maximum -25V -25V -25V - 50mA - 50mA - 50mA 45MHz 1000MHZ 2500MHz — — — 0.07 0.30 0.60 0.10 0.45 0.80 -25V - 50mA 45MHz 36 39 — Return Loss dB -25V -25V -25V - 50mA - 50mA + 50mA 1000MHZ 2500MHz 45MHz 18 11 60 20 13 63 — — — Isolation dB -25V + 50mA 1000MHZ 40 42 — -25V + 50mA 2500MHz 29 33 — +66 — Input IP3 dBm -25V - 50mA -50mA / -25V F1 = 500MHz F2 = 505MHz PIN = +40dBm(each tone) 2nd Harmonic dBc -25V - 50mA 50mA / -25V 500MHz /+35dBm — -46 — 3rd Harmonic dBc -25V - 50mA 50mA / -25V 500MHz /+35dBm — -60 — — ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, • India Tel: +91.80.43537383 • China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-001150-1316 SURMOUNT PIN Diode Switch Element with Thermal Terminal V5 Typical RF Small Signal Performance MASW-001150-13160 Insertion Loss, Isolation, Return Loss From 45-3000 MHz Isolation_+5mA Return loss_-50 mA Insertion Loss_-50mA 0 -0.1 -10 -0.2 -20 -0.3 -30 -0.4 -40 -0.5 -50 -0.6 -60 -0.7 -70 -0.8 Isolation & Return Loss (dB) Insertion Loss (dB) 0.0 -80 0.0 0.5 1.0 1.5 2.0 2.5 3.0 Frequency (GHz) 3 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, • India Tel: +91.80.43537383 • China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-001150-1316 SURMOUNT PIN Diode Switch Element with Thermal Terminal V5 MASW-001150-13160W Configured as an Absorptive High Power SPST Switch Note: The bias circuits provided in the schematic above assumes current sources are available. If only voltage sources are available, a resistor will need to be added to the RF Input (J1) Bias Return Network. When using a D.C. voltage of 25V, a 500Ω resistor must be used to draw 50mA of current into the switch. 4 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, • India Tel: +91.80.43537383 • China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-001150-1316 SURMOUNT PIN Diode Switch Element with Thermal Terminal V5 MASW-001150-13160W Configured as a Reflective SPST Switch Note: The bias circuits provided in the schematic above assumes current sources are available. If only voltage sources are available, a resistor will need to be added to the RF Input (J1) Bias Return Network. When using a D.C. voltage of 25V, a 500Ω resistor must be used to draw 50mA of current into the switch. 5 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, • India Tel: +91.80.43537383 • China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-001150-1316 SURMOUNT PIN Diode Switch Element with Thermal Terminal V5 RF , DC, and Thermal Circuit Footprint ( Topview ) 22 +0/-2 mil (4) PL RF Output Trace Direction RF Output 20 ±1 mil (4) PL 22 +0/-2 mil (4) PL RF Input Trace Direction RF Input Thermal Terminal Shunt Cathode Return Thermal Circuit Vias D.C Ground or RF Trace Direction 6 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, • India Tel: +91.80.43537383 • China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-001150-1316 SURMOUNT PIN Diode Switch Element with Thermal Terminal V5 Chip Outline and Port Designations Top View Dimension Inches min. max. 0.0665 0.0673 0.0665 0.0673 0.0045 0.0053 0.0195 0.0205 0.0195 0.0205 0.0195 0.0205 0.0195 0.0205 A B C D E F G Millimeters min. max. 1.69 1.71 1.69 1.71 0.115 0.135 0.495 0.520 0.495 0.520 0.495 0.520 0.495 0.520 Ports Function 1 RF Input 2 Thermal Terminal for Series Diode (Electrically isolated from other ports) 3 Shunt Diode (Cathode Return) 4 RF Output / D.C. bias Notes: Backside Metal: 2.5μm thick Au Hatched yellow areas are I/O ports (die solder pads) Bottom View Ordering Information 7 Part Number Packaging MASW-001150-13160W Waffle Tray MASW-001150-13160P Pocket Tape ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, • India Tel: +91.80.43537383 • China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-001150-1316 SURMOUNT PIN Diode Switch Element with Thermal Terminal Component C1, C2 C3, C4 L1, L2, L3, L4 Value 0.01μF 100pF 390nH V5 Case Size 0402 0402 0603 Manufacturer Murata Murata Coilcraft Ordering Information for Test Board Part Number MASW-001150-001SMB 8 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, • India Tel: +91.80.43537383 • China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-001150-1316 SURMOUNT PIN Diode Switch Element with Thermal Terminal V5 Assembly Guidelines Handling All semiconductor chips should be handled with care to avoid damage or contamination from perspiration and skin oils. The use of plastic tipped tweezers or vacuum pickups is strongly recommended for individual components. Bulk handling should insure that abrasion and mechanical shock are minimized. Bonding Attachment to a circuit board is made simple through the use of surface mount technology. Mounting pads are conveniently located on the bottom surface of these devices and are removed from the active junction locations. These devices are well suited for solder or conductive epoxy attachment onto hard or soft substrates. The use of 60Pb/40Sn, 80Au/20Sn or any RoHS lead-free solder is recommended to achieve the lowest series resistance and optimum heat sink. The thermal terminal is not electrically conductive and may be soldered directly to any appropriate heat sink without affecting RF performance. When soldering these devices to a hard substrate, hot gas die bonding is preferred. When soldering, position the die so that its mounting pads are aligned with the circuit board mounting pads and reflow the solder by heating the circuit trace near the mounting pads while applying 40 to 60 grams of force perpendicular to the top surface of the die. All mounting pads should be heated simultaneously so that the solder under the pads flows evenly and at the same time. Avoid soldering the pads one at a time as doing so may produce non-uniform heat flow which potentially could create thermal stress to the chip. Die should be uniformly heated in a re-flow oven and not by causing heat to flow directly through the top surface of the die. Since the HMIC glass is transparent, the edges of the mounting pads can be visually inspected through the top surface of the die to ensure proper solder flow and attachment. A typical soldering process profile and handling instructions are provided in Application Notes, M538 Surface Mounting Instructions and M541 Bonding and Handling Procedures on the MA/COM Technology Solutions website at www.macomtech.com Conductive silver epoxy may also be used for die attachment in lower Incident power applications where the average power is <1W. Apply a thin controlled amount, approximately 1- 2 mils thick, to minimize ohmic and thermal stresses and maximize heat transfer. Take care not to bridge the gap between the chip pads with epoxy. A thin epoxy fillet should be visible around the perimeter of the pads after placement to ensure full coverage. Cure epoxy per manufacturer’s recommended schedule. Typically 150°C for one hour. 9 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, • India Tel: +91.80.43537383 • China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice.