NEMIC-LAMBDA JWS 150 SPECIFICATIONS A160-01-01A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Isolation Resistance 29 Vibration 30 Shock (In package) 31 Safety 32 33 34 35 JWS150 JWS150 JWS150 JWS150 JWS150 -5 -12 -15 -24 -48 5 12 15 24 48 30 13 10 6.5 3.3 150 156 150 156 158.4 75 77 78 80 80 85 ~ 265VAC (47 ~ 63Hz) or 120 ~ 330VDC 1.5/0.75 2.0/1.0 25A at 100VAC, 50A at 200VAC, Ta=25°C, Cold Start Built to meet EN61000-3-2 0.99/0.95 2.85~3.63 4.5~5.5 10.8~13.2 13.5~16.5 21.6~26.4 43.2~52.8 120 120 150 150 150 200 160 160 180 180 180 240 20 20 48 60 96 192 40 40 96 120 150 240 Less than 0.02%/°C 31.5 ~ 31.5 ~ 13.65 ~ 10.5 ~ 6.82 ~ 3.46 ~ 3.79~4.95 5.75~6.75 13.8~16.2 17.3~20.3 27.6~32.4 55.2~64.8 20ms 0.75mA MAX, 0.2mA(Typ) at 100VAC / 0.44mA(Typ) at 230VAC Possible Possible -10 ~+60°C ( -10 ~+50°C:100%, +60°C:60%) 30 ~ 90%RH (No dewdrop) -30 ~ +85°C 10 ~ 95%RH (No dewdrop) Convection Cooling Input - FG : 2kVAC (20mA), Input - Output : 3kVAC (20mA) Output - FG : 500VAC (100mA) for 1min More than 100MΩ at 25°C and 70%RH Output - FG ... 500VDC At no operating, 10 ~ 55Hz (Sweep for 1min) 2 19.6m/s Constant, X,Y,Z 1hour each. 2 Less than 196.1m/s Approved by UL1950, CSA950, EN60950,VDE0160. (*11) Built to meet DENTORI. Built to meet EN55011/EN55022-B, FCC-ClassB, VCCI-B. Built to meet EN55011/EN55022-B, FCC-ClassB, VCCI-B. 850 g 65 x 92 x 198 ( Refer to Outline Drawing ) mm MODEL ITEMS Nominal Output Voltage V Maximum Output Current A Maximum Output Power W Efficiency (Typ) (*1) % Input Voltage Range (*2) Input Current (100/200VAC)(Typ) (*1) A Inrush Current(Typ) PFHC Power Factor (100/200VAC)(Typ) (*1) Output Voltage Range V Maximum Ripple & Noise 0 ~ +60°C mV (*3) -10 ~ 0°C mV Maximum Line Regulation (*4) mV Maximum Load Regulation (*5) mV Temperature Coefficient Over Current Protection (*6) A Over Voltage Protection (*7) V Hold-up Time (Typ) (*8) Leakage Current (*9) Remote Sensing Parallel Operation Series Operation Operating Temperature (*10) Operating Humidity Storage Temperature Storage Humidity Cooling Withstand Voltage - Conducted Emission Radiated Emission Weight(Typ.) Size (W x H x D) JWS150 -3 3.3 30 99 67 *Read instruction manual carefully, before using the power supply unit. =NOTES= *1. At 100/200VAC, Ta=25°C and maximum output power. *2. For cases where conformance to various safety specs (UL, CSA, EN) are required, input voltage range will be 100 ~ 240VAC(50/60Hz). *3. Measure with EIAJ RC-9131 probe, Bandwise of scope :100MHz. *4. 85 ~ 265VAC , constant load. *5. No load-Full load, constant input voltage. *6. Constant current limit with automatic recovery. *7. OVP circuit will shut down output, manual reset (Line recycle). *8. At 100/200VAC nominal output voltage and maximum output current. *9. Measured by the each measuring method of UL,CSA,EN and DENTORI(at 60Hz). *10. Ratings - Derating at standard mounting. - Load (%) is percent of maximum output power or maximum output current, whichever is greater. - As for other mountings, refer to derating curve (A160-01-02_). NEMIC-LAMBDA JWS 150 OUTPUT DERATING A160-01-02 Ta(°C) -10 ~+40 45 50 55 60 MOUNTING A 100 100 100 80 60 LOAD(%) MOUNTING B 100 80 60 - MOUNTING C 100 80 60 - OUTPUT DERATING CURVE 100 LOAD(%) 80 MOUNTING A MOUNTING B,C 60 40 20 0 -10 0 10 20 30 40 50 60 Ta(°C) MOUNTING A (STANDARD MOUNTING) MOUNTING B MOUNTING C DON'T USE DON'T USE