ZXLD1374 - Diodes Incorporated

A Product Line of
Diodes Incorporated
ZXLD1374
60V HIGH ACCURACY 1.5A BUCK/BOOST/BUCK-BOOST
LED DRIVER CONVERTER WITH AEC-Q100
Description
Pin Assignments
The ZXLD1374 is a 60V LED driver with integrated 1.5A low side
ADJ
REF
TADJ
SHP
switch to drive high current LEDs. It is a multi-topology converter
enabling it to operate in Buck, Boost and Buck-boost configurations;
efficiently controlling the current of up to 16-series connected LEDs.
The ZXLD1374 is a modified hysteretic converter using a patent
pending control scheme providing high output current accuracy in all
1
2
3
4
STATUS 5
SGND 6
PGND 7
PGND 8
N/C 9
N/C 10
three topologies. High accuracy dimming is achieved through
DC control and high frequency PWM control.
The ZXLD1374 uses two pins for fault diagnosis. A flag output
highlights a fault, while the multi-level status pin gives further
information on the exact fault.
The ZXLD1374 has been qualified to AEC-Q100 Grade 1 enabling
operation in ambient temperatures from -40 to +125°C.
Thermal
Pad
20
19
18
17
GI
PWM
FLAG
ISM
16
15
14
13
12
11
VIN
VAUX
LX
LX
N/C
N/C
Features
•
•
•
•
•
•
•
•
•
•
•
0.5% Typical Output Current Accuracy
6.3 to 60V Operating Voltage Range
1.5A Integrated Low Side Switch
LED Driver Supports Buck, Boost and Buck-Boost Topologies
Wide Dynamic Range Dimming
20:1 DC Dimming
1000:1 Dimming Range at 500Hz
Up to 1MHz Switching
High Temperature Control of LED Current Using TADJ
AEC-Q100 Grade 1
TSSOP-20EP: Available in “Green” Molding Compound (No Br,
Sb) with lead Free Finish/ RoHS Compliant
ƒ
Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2)
ƒ
Halogen and Antimony Free. “Green” Device (Note 3)
Notes:
1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant.
2. See http://www.diodes.com for more information about Diodes Incorporated’s definitions of Halogen and Antimony free, "Green" and Lead-Free.
3. Halogen and Antimony free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl)
and <1000ppm antimony compounds.
Typical Applications Circuit
VIN
R1
L1
VAUX VIN
PWM
GI
C1
RGI2
ISM
LX
LX
FLAG
REF
STATUS
TADJ
SHP NC SGND PGND
ADJ ZXLD1374
R4
RGI2 TH1
SD1
PSD3200
COUT
C2
100pF
GND
ZXLD1374
Document number: DS35032 Rev. 3 - 2
1 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Pin Descriptions
Pin
Name
Pin
Type
(Note 4)
ADJ
1
I
REF
2
O
TADJ
3
I
SHP
4
I/O
STATUS
5
O
SGND
6
P
PGND
7, 8
P
N/C
9, 10, 11, 12
—
LX
13, 14
O
VAUX
15
P
VIN
16
P
ISM
17
I
FLAG
18
O
PWM
19
I
GI
20
I
EP
PAD
P
Note:
Function
Adjust Input (for DC Output Current Control).
Connect to REF to set 100% output current.
Drive with dc voltage (125mV<VADJ< 2.5V) to adjust output current from 10% to 200% of set value. The
ADJ pin has an internal clamp that limits the internal node to less than 3V. This prevents the LED and power
switch from delivering too much current should ADJ get overdriven.
Internal 1.25V reference voltage output
Temperature Adjust (Input for LED Thermal Current Control).
Connect thermistor/resistor network to this pin to reduce output current above a preset temperature threshold.
Connect to REF to disable thermal compensation function (See section on thermal control).
Shaping capacitor for feedback control loop.
Connect 100pF ±20% capacitor from this pin to ground to provide loop compensation
Operation Status Output (analog output).
Pin is at 4.5V (nominal) during normal operation.
Pin switches to a lower voltage to indicate specific operation warnings or fault conditions (See section on
STATUS output).
Status pin voltage is low during shutdown mode.
Signal Ground.
Connect to 0V and pins 7 and 8.
Power Ground.
Connect to 0V and pin 6 to maximize copper area.
Not Connected Internally.
To maximize PCB copper for thermal dissipation connect to pins 7 and 8.
Low-Side Power-Switch Output
Auxiliary Positive Supply to Internal Switch Gate Driver.
Connect to VIN, or auxiliary supply from 6V to 15V supply to reduce internal power dissipation (Refer to
application section for more details).
At VIN >24V; to reduce power dissipation, VAUX can be connected to a 12V to 15V auxiliary power supply
(see Applications section).
Decouple to ground with capacitor close to device (refer to Applications section).
Input Supply to Device (6.3V to 60V).
Decouple to ground with capacitor close to device (refer to Applications section).
Current Monitor Input.
Connect current sense resistor between this pin and VIN.
The nominal voltage, VSENSE, across the resistor is 218mV fixed in Buck mode and initially 225mV in Boost
and Buck-Boost modes, varying with duty cycle.
Flag Open Drain Output.
Pin is high impedance during normal operation.
Pin switches low to indicate a fault, or warning condition.
Digital PWM Output Current Control.
Pin driven either by open Drain or push-pull 3.3V or 5V logic levels.
Drive with frequency higher than 100Hz to gate output ‘on’ and ‘off’ during dimming control.
The device enters standby mode when PWM pin is driven with logic low level for more than 15ms nominal
(Refer to application section for more details).
Gain Setting Input.
Used to set the LED current in Boost and Buck-Boost modes.
In Buck mode operation the GI pin must be connected to ADJ.
For Boost and Buck-boost modes, connect to resistive divider from ADJ to SGND. This defines the ratio of
switch current to LED current (see application section). The GI pin has an internal clamp that limits the
internal node to less than 3V. This provides some failsafe should the GI pin get overdriven.
Exposed Pad.
Connect to 0V plane for electrical and thermal management.
4. Type refers to whether or not pin is an Input, Output, Input/Output or Power supply pin.
ZXLD1374
Document number: DS35032 Rev. 3 - 2
2 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Functional Block Diagram
ZXLD1374
Document number: DS35032 Rev. 3 - 2
3 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Absolute Maximum Ratings (Voltages to GND unless otherwise specified.)
Symbol
Parameter
Input Supply Voltage Relative to GND
VIN
‡
VAUX
Auxiliary Supply Voltage Relative to GND
VISM
Current Monitor Input Relative to GND
‡
VSENSE
Current Monitor Sense Voltage (VIN-VISM)
VLX
Low Side Switch Output Voltage to GND
ILX
Low Side Switch Continuous Output Current
‡
Status Pin Output Current
ISTATUS
VFLAG
VPWM, VADJ, VTADJ, VGI
Note:
Rating
‡
Unit
-0.3 to +65
V
-0.3 to +65
V
-0.3 to +65
V
-0.3 to +5
V
-0.3 to +65
V
1.8
A
±1
mA
Flag Output Voltage to GND (Note 5)
-0.3 to +40
V
Other Input Pins to GND (Note 5)
-0.3 to +5.5
V
ESD HBM
Human Body Model ESD Protection
500
V
ESD CDM
Charged Device Model ESD Protection
1000
V
150
°C
-55 to +150
°C
TJ
Maximum Junction Temperature
TST
Storage Temperature
5. For correct operation SGND and PGND should always be connected together.
These are stress ratings only. Operation outside the absolute maximum ratings may cause device failure.
Operation at the absolute maximum rating for extended periods may reduce device reliability.
Semiconductor devices are ESD sensitive and may be damaged by exposure to ESD events. Suitable ESD precautions should be taken when handling and
transporting these devices.
Package Thermal Data
Thermal Resistance
Package
Junction-to-Ambient, θJA (Note 6)
TSSOP-20EP
Junction-to-Case, θJC
Note:
Unit
28
°C/W
4
°C/W
6. Measured on High Effective Thermal Conductivity Test Board" according JESD51.
ZXLD1374
Document number: DS35032 Rev. 3 - 2
4 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Recommended Operating Conditions (@TA = +25°C, unless otherwise specified.)
Symbol
VIN
VAUX
VSENSE
Parameter
Input Supply Voltage Range
Auxiliary Supply Voltage Range (Note 8)
Differential Input Voltage
Performance/Comment
Normal operation
Reduced performance operation (Note 7)
Normal operation
Min
8
6.3
8
Reduced performance operation (Note 7)
6.3
VVIN-VISM, with 0 ≤ VADJ ≤ 2.5
0
Max
Unit
60
V
60
V
450
mV
VLX
Low Side Switch Output Voltage
60
V
ILX
Low Side Switch Continuous Output Current
1.5
A
2.5
V
VADJ
ISTATUS
DC brightness control mode
from 10% to 200%
External DC Control Voltage Applied to ADJ Pin to
Adjust Output Current
0.125
Status Pin Output Current
IREF
Reference External Load Current
fSW
Recommended Switching Frequency Range (Note 9)
VTADJ
Temperature Adjustment (TADJ) Input Voltage Range
100
µA
1
mA
300
1000
kHz
0
VREF
500
1000
Hz
Hz
REF sourcing current
Recommended PWM Dimming Frequency Range
tPWMH/L
PWM Pulse Width in Dimming Mode
PWM input high or low
0.005
10
ms
VPWMH
PWM Pin High Level Input Voltage
2
5.5
V
VPWML
PWM Pin Low Level Input Voltage
0
0.4
V
-40
+125
°C
0.20
0.50
fPWM
TJ
GI
Notes:
Operating Junction Temperature Range
Gain Setting Ratio for Boost and Buck-Boost Modes
Ratio= VGI/VADJ
100
100
V
To maintain 1000:1 resolution
To maintain 200:1 resolution
7. Device is guaranteed to have started up by 6.5V and as such the minimum applied supply voltage has to be above 6.5V (plus any noise margin).
The ZXLD1374 will, however, continue to function when the input voltage is reduced from ≥ 8V down to 6.3V.
When operating with input voltages below 8V the output current and device parameters may deviate from their normal values; and is dependent on
power MOSFET switch, load and ambient temperature conditions. To ensure best operation in Boost and Buck-boost modes with input voltages, VIN,
between 6.5 and 12V a suitable boot-strap network on VAUX pin is recommended. Performance in Buck mode will be reduced at input voltages (VIN,
VAUX) below 8V. – A boot-strap network cannot be implemented in buck mode.
8. VAUX can be driven from a voltage higher than VIN to provide higher efficiency at low VIN voltages, but to avoid false operation; a voltage should not
be applied to VAUX in the absence of a voltage at VIN.
9. The device contains circuitry to control the switching frequency to approximately 400kHz. The maximum and minimum operating frequency is not
tested.
ZXLD1374
Document number: DS35032 Rev. 3 - 2
5 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Electrical Characteristics (VIN = VAUX = 12V, @TA = +25°C, unless otherwise specified.)
Symbol
Parameter
Supply and Reference Parameters
Under-Voltage Detection Threshold
VUVNormal Operation to Switch Disabled
Under-Voltage Detection Threshold
Switch Disabled to Normal Operation
VUV+
IQ-IN
Quiescent Current into VIN
IQ-AUX
Quiescent Current into VAUX
ISB-IN
Standby Current into VIN.
Conditions
Min
Typ
Max
VIN or VAUX falling (Note 10)
5.2
5.6
6.3
VIN or VAUX rising (Note 10)
5.5
6
6.5
PWM pin floating.
Output not switching
PWM pin grounded for more than 15ms
ISB-AUX
Standby Current into VAUX.
VREF
Internal Reference Voltage
No load
Change in Reference Voltage with Output
Current
Sourcing 1mA
VREF_LINE
Reference Voltage Line Regulation
VIN = VAUX, 6.5V < VIN = <60V
VREF-TC
Reference Temperature Coefficient
ΔVREF
1.237
V
V
1.5
3
mA
150
300
µA
90
150
µA
0.7
10
µA
1.25
1.263
V
-5
Sinking 25µA
5
-60
Units
mV
-90
dB
+/-50
ppm/°C
DC-DC Converter Parameters
VADJ
External DC Control Voltage Applied to ADJ Pin DC brightness control mode
to Adjust Output Current (Note 11)
10% to 200%
IADJ
ADJ Input Current (Note 11)
VGI
GI Voltage Threshold for Boost and Buck-Boost
VADJ = 1.25V
Modes Selection (Note 11)
IGI
GI Input Current (Note 11)
VGI ≤ 2.5V
VGI = 5.0V
PWM Input Current
VPWM = 5.5V
IPWM
tPWMoff
TSDH
PWM Pulse Width
(to enter shutdown state)
Thermal Shutdown Upper Threshold
(LX output inhibited)
Thermal Shutdown Lower Threshold
(LX output re-enabled)
TSDL
0.125
1.25
2.5
V
100
5
nA
µA
0.8
V
100
5
nA
µA
36
100
µA
15
25
ms
VADJ ≤ 2.5V
VADJ = 5.0V
PWM input low
10
Temperature rising
150
°C
Temperature falling
125
°C
High-Side Current Monitor (Pin ISM)
Input Current
IISM
VSENSE_acc Accuracy of Nominal VSENSE Threshold Voltage
VSENSE-OC Over-Current Sense Threshold Voltage
Notes:
Measured into ISM pin and VISM = VIN
VADJ = 1.25V
300
11
20
µA
±0.25
±2
%
350
375
mV
10. UVLO levels are such that all ZXLD1374 will function above 6.5V for rising supply voltages and function down to 6.3V for falling supply voltages.
11. The ADJ and GI pins have an internal clamp that limits the internal node to less than 3V. This limits the switch current should those pins get
overdriven.
ZXLD1374
Document number: DS35032 Rev. 3 - 2
6 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Electrical Characteristics (cont.) (VIN = VAUX = 12V, @TA = +25°C, unless otherwise specified.)
Symbol
Output Parameters
VFLAGL
IFLAGOFF
VSTATUS
RSTATUS
Parameter
Conditions
FLAG Pin Low Level Output Voltage
Output sinking 1mA
FLAG Pin Open-Drain Leakage Current
VFLAG = 40V
STATUS Flag No-Load Output Voltage
(Note 13)
Output Impedance of STATUS Output
Min
Typ
Max
Units
0.5
V
1
µA
Normal operation
4.2
4.5
4.8
Out of regulation (VSHP out of range)
(Note 12)
3.3
3.6
3.9
VIN under-voltage (VIN < 5.6V)
3.3
3.6
3.9
Switch stalled (tON or tOFF> 100µs)
3.3
3.6
3.9
LX over-voltage state (VLX > 60V)
2.4
2.7
3.0
Over-temperature (TJ > 125°C)
1.5
1.8
2.1
Excess sense resistor current
(VSENSE > 0.375V)
0.6
0.9
1.2
Excessive switch current (ISW>1.5A)
0.6
0.9
1.2
V
Normal operation
10
kΩ
Low Side Switch Leakage Current
Output stage off, VLX = 60V
(Note 14)
60
µA
LX Pin MOSFET on Resistance
ILX = 1.5A (tON < 100µs)
0.5
Low Side Switch Output (LX pins tied together)
ILX-LG
RDS(ON)
Propagation Delay High-Low
tPDHL
tPDLH
Propagation Delay Low-High
tLXR
LX Output Rise Time
tLXF
LX Output Fall Time
Time to assert ‘STALL’ flag and
warning on STATUS output
(Note 15)
tSTALL
VSENSE = 225mV ± 30%, CL = 680pF,
RL = 120Ω
LX low or high
0.8
Ω
86
ns
131
ns
208
ns
12
ns
100
170
µs
LED Thermal control circuit (TADJ) parameters
VTADJH
Upper Threshold Voltage
Onset of output current reduction (VTADJ
falling)
560
625
690
mV
VTADJL
Lower Threshold Voltage
Output current reduced to <10% of set value
(VTADJ falling)
380
440
500
mV
TADJ Pin Input Current
VTADJ = 1.25V
1
µA
ITADJ
Notes:
12. Flag is asserted if VSHP<2.5V or VSHP>3.5V
13. In the event of more than one fault/warning condition occurring, the higher priority condition will take precedence. E.g. ‘Excessive coil current’
and ‘Out of regulation’ occurring together will produce an output of 0.9V on the STATUS pin. The voltage levels on the STATUS output assume
the Internal regulator to be in regulation and VADJ<=VREF. A reduction of the voltage on the STATUS pin will occur when the voltage on VIN is near –
this is due to the feedback loop increasing the sense voltage.
14. With the device still in switching mode the LX pin has an over-voltage detection circuit connected to it with a resistance of approximately 1MΩ.
15. If tON exceeds tSTALL, LX turns off and then an initiate a restart cycle occurs. During this phase, ADJ is grounded internally and the SHP pin is
switched to its nominal operating voltage, before operation is allowed to resume. Restart cycles will be repeated automatically until the operating
conditions are such that normal operation can be sustained. If tOFF exceeds tSTALL, the switch will remain off until normal operation is possible.
ZXLD1374
Document number: DS35032 Rev. 3 - 2
7 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
1500
900
2.5
1250
750
1000
600
LED CURRENT (mA)
3
2
1.5
1
6
12
Switching
Frequency
500
0
300
TA = 25°C
VAUX = VIN = 12V
2LEDs
L = 33µH
RS = 300mΩ
150
0
1.5
2.5
1
2
ADJ VOLTAGE (V)
Figure 2 Buck LED Current, Switching Frequency vs. VADJ
18
24 30 36 42 48 54 60
SUPPLY VOLTAGE (V)
Figure 1 Supply Current vs. Supply Voltage
0
0.5
700
650
1400
700
650
700
600
1200
600
600
450
400
ILED
800
350
Switching
Frequency
300
600
250
200
TA = 25°C
VAUX = VIN = 24V
8LEDs
L = 33µH
GI = 0.23
RS = 300mΩ
150
100
50
0
400
200
500
500
450
ILED
400
0.5
400
350
Switching
Frequency
300
300
250
200
150
TA = 25°C
VAUX = VIN = 12V
12 LEDs
L = 33µH
RS = 300mΩ
100
50
0
1
1.5
2
2.5
ADJ VOLTAGE
Figure 3 Buck-Boost LED Current, Switching Frequency vs. VADJ
0
LED CURRENT (mA)
1000
550
200
100
SWITCHING FREQUENCY (kHz)
500
SWITCHING FREQUENCY (kHz)
550
LED CURRENT (mA)
450
250
0.5
0
ILED
750
SWITCHING FREQUENCY (kHz)
SUPPLY CURRENTt (mA)
Typical Characteristics
0
0.25 0.5 0.75 1 1.25 1.5 1.75 2 2.25 2.5
ADJ VOLTAGE
Figure 4 Boost LED Current, Switching Frequency vs. VADJ
0
0
1500
LED CURRENT (mA)
1250
1000
750
500
250
0
0
10
20
30 40 50 60 70 80 90 100
PWM DUTY CYCLE (%)
Figure 5 ILED vs. PWM Duty Cycle
ZXLD1374
Document number: DS35032 Rev. 3 - 2
Figure 6 ILED vs. Time - PWM Pin Transient Response
8 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Typical Characteristics (cont.)
1.252
100%
60%
40%
20%
1.251
1.2505
1.25
1.2495
1.249
1.2485
0%
POWER SWITCH ON-RESISTANCE (Ω)
REFERENCE VOLTAGE (V)
80%
0
250
500
750
1000
TADJ PIN VOLTAGE (mV)
Figure 7 LED Current vs. TADJ Voltage
1.248
-40 -25 -10 5 20 35 50 65 80 95 110 125
JUNCTION TEMPERATURE (°C)
Figure 8 VREF vs. Temperature
1250
0.9
100%
0.8
90%
70%
0.6
60%
0.5
0.4
30%
0.2
20%
VIN = 12V
ILX= 1.3A
10%
0
-40 -25 -10 5 20 35 50 65 80 95 110 125
JUNCTION TEMPERATURE (°C)
Figure 9 RDS(ON) vs. Temperature
ZXLD1374
Document number: DS35032 Rev. 3 - 2
50%
40%
0.3
0.1
TA = 25°C
L = 33µH
RS = 150mΩ
Buck Mode
2 LEDS
80%
0.7
DUTY
LED CURRENT DIMMING FACTOR
1.2515
0%
9 of 39
www.diodes.com
6
12
18
24 30 36 42 48 54
INPUT VOLTAGE (V)
Figure 10 Duty Cycle vs. Input Voltage
60
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Typical Characteristics – Buck Mode – RS = 146mΩ, L = 35µH, ILED = 1.5A
1.65
TA = 25°C
VAUX = VIN
L = 33µH
RS = 146mΩ
LED CURRENT (A)
1.60
9 LEDs
11 LEDs
13 LEDs
15 LEDs
1.55
1.50
1.45
3 LEDs
1 LED
5 LEDs
7 LEDs
1.40
1.35
6
12
18
24
30
36
42
48
INPUT VOLTAGE (V)
Figure 11 Load Current vs. Input Voltage and Number of LED
54
60
SWITCHING FREQUENCY (kHz)
1200
TA = 25°C
VAUX = VIN
L = 33µH
RS = 146mΩ
1000
800
600
400
200
3 LEDs
0
1 LED
6
5 LEDs
12
18
7 LEDs
9 LEDs
11 LEDs
13 LEDs
24
30
36
42
48
INPUT VOLTAGE (V)
Figure 12 Frequency vs. Input Voltage and Number of LED
100%
15 LEDs
54
60
15 LEDs
95%
5 LEDs
EFFICIENCY
90%
85%
3 LEDs
7 LEDs
9 LEDs
11 LEDs
13 LEDs
80%
1 LED
75%
70%
TA = 25°C
VAUX = VIN
L = 33µH
RS = 146mΩ
65%
60%
6
ZXLD1374
Document number: DS35032 Rev. 3 - 2
12
18
24
30
36
42
48
Input Voltage (V)
Figure 13 Efficiency vs. Input Voltage and Number of LED
10 of 39
www.diodes.com
54
60
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Typical Characteristics – Buck Mode – RS = 291mΩ, L = 35µH, ILED = 750mA
0.825
TA = 25°C
VAUX = VIN
L = 33µH
RS = 291mΩ
LED CURRENT (A)
0.800
3 LEDs
0.775
7 LEDs
5 LEDs
1 LED
15 LEDs
11 LEDs
9 LEDs
13 LEDs
0.750
0.725
0.700
0.675
6
1000
18
24
30
36
42
48
INPUT VOLTAGE (V)
Figure 14 ILED vs. Input Voltage and Number of LED
TA = 25°C
VAUX = VIN
L = 33µH
R S = 291mΩ
900
800
FREQUENCY (kHz)
12
54
60
11 LEDs
9 LEDs
7 LEDs
700
5 LEDs
600
500
3 LEDs
13 LEDs
15 LEDs
400
300
1 LED
200
100
0
6
12
100%
18
30
36
42
48
INPUT VOLTAGE (V)
Figure 15 Frequency ZXLD1374 - Buck Mode = L = 47μH
5 LEDs
24
7 LEDs
9 LEDs
11 LEDs
13 LEDs
54
60
15 LEDs
95%
EFFICIENCY
90%
3 LEDs
85%
1 LED
80%
75%
70%
65%
60%
6
ZXLD1374
Document number: DS35032 Rev. 3 - 2
TA = 25°C
VAUX = VIN
L = 33µH
RS = 291mΩ
12
18
30
36
48
42
INPUT VOLTAGE (V)
Figure 16 Efficiency vs. Input Voltage and Number of LED
24
11 of 39
www.diodes.com
54
60
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Typical Characteristics – Boost Mode – RS = 150mΩ, L = 33µH, ILED = 325mA, GIRATIO = 0.21
0.358
TA = 25°C
L = 33µH
RS = 150mΩ
RGI1 = 33kΩ
0.347
LED CURRENT (A)
RGI2 = 120kΩ
0.336
0.325
0.314
6 LEDs
8 LEDs
0.303
0.292
12
10 LEDs
12 LEDs
16 LEDs
14 LEDs
37
27
32
INPUT VOLTAGE (V)
Figure 17 ILED vs. Input and Number of LED
17
42
22
47
FREQUENCY (kHz)
700
650
TA = 25°C
L = 33µH
RS = 150mΩ
600
RGI1 = 33kΩ
RGI2 = 120kΩ
550
500
450
400
350
300
12 LEDs
14 LEDs
16 LEDs
6 LEDs
250
200
8 LEDs
12
17
10 LEDs
22
27
32
37
INPUT VOLTAGE (V)
Figure 18 Frequency vs. Input Voltage and Number LED
42
47
100%
6 LEDs
8 LEDs
10 LEDs
12 LEDs
14 LEDs
16 LEDs
EFFICIENCY
95%
90%
85%
80%
T A = 25°C
L = 33µH
RS = 150mΩ
RGI1 = 33kΩ
RGI2 = 120kΩ
75%
12
ZXLD1374
Document number: DS35032 Rev. 3 - 2
17
22
27
32
37
INPUT VOLTAGE (V)
Figure 19 Efficiency vs. Input Voltage and Number of LED
12 of 39
www.diodes.com
42
47
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Typical Characteristics – Boost Mode – RS = 150mΩ, L = 33µH, ILED = 350mA, GIRATIO = 0.23 with Bootstrap
0.385
LED CURRENT (A)
0.368
15 LEDs
13 LEDs
11 LEDs
0.350
7 LEDs
9 LEDs
5 LEDs
0.333
TA = 25°C
L = 33µH
RS = 150mΩ
RGI1 = 36mΩ
RGI2 = 120mΩ
0.315
6.5
8
9.5
11
12.5
14
15.5
INPUT VOLTAGE (V)
Figure 20 Load Current vs. Input Voltage and Number of LED
17
700
SWITCHING FREQUENCY (kHz)
600
15 LEDs
500
13 LEDs
11 LEDs
400
9 LEDs
7 LEDs
300
5 LEDs
200
100
0
6.5
T A = 25°C
L = 33µH
RS = 150mΩ
RGI1 = 36mΩ
RGI2 = 120mΩ
8
12.5
14
11
INPUT VOLTAGE (V)
Figure 21 Frequency vs. Input Voltage and Number of LED
9.5
15.5
17
100%
7 LEDs
5 LEDs
95%
EFFICIENCY
90%
15 LEDs
85%
13 LEDs
80%
9 LEDs
11 LEDs
75%
70%
6.5
ZXLD1374
Document number: DS35032 Rev. 3 - 2
TA = 25° C
L = 33µH
RS = 150mΩ
8
9.5
11
12.5
14
INPUT VOLTAGE (V)
Figure 22 Efficiency vs. Input Voltage and Number of LED
13 of 39
www.diodes.com
15.5
17
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Typical Characteristics – Buck - Boost Mode – RS = 150mΩ, L = 33µH, ILED = 350mA, GIRATIO = 0.23 with Bootstrap
0.385
0.375
LED CURRENT (mA)
0.365
8 LEDs
7 LEDs
6 LEDs
0.355
0.345
5 LEDs
4 LEDs
3 LEDs
0.335
TA = 25°C
L = 33µH
RS = 150mΩ
0.325
0.315
6.5
RGI1 = 36mΩ
RGI2 = 120mΩ
8.0
9.5
11.0
12.5
14.0
INPUT VOLTAGE (V)
Figure 23 LED Current vs. Input Voltage and Number of LED
15.5
17.0
600
SWITCHING FREQUENCY (kHz)
6 LEDs
8 LEDs
7 LEDs
500
400
5 LEDs
300
4 LEDs
3 LEDs
200
TA = 25°C
L = 33µH
RS = 150mΩ
100
RGI1 = 36kΩ
RGI2 = 120kΩ
0
6.5
100%
95%
8.0
9.5
11.0
12.5
14.0
15.5
INPUT VOLTAGE (V)
Figure 24 Switching Frequency vs. Input Voltage and Number of LED
17.0
T A = 25°C
L = 33µH
RS = 150mΩ
RGI1 = 36KΩ
EFFICIENCY
RGI2 = 120kΩ
90%
85%
80%
75%
70%
6.5
ZXLD1374
Document number: DS35032 Rev. 3 - 2
8 LEDs
8.0
7 LEDs
6 LEDs
9.5
5 LEDs
4 LEDs
11.0
12.5
14.0
INPUT VOLTAGE (V)
Figure 25 Efficiency vs. Input Voltage and Number of LED
14 of 39
www.diodes.com
3 LEDs
15.5
17.0
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information
The ZXLD1374 is a high accuracy hysteretic inductive Buck/Boost/Buck-boost converter with an internal NMOS switch designed to be used for
current-driving single or multiple series-connected LEDs. The device can be configured to operate in Buck, Boost, or Buck-boost modes by
suitable configuration of the external components as shown in the schematics shown in the device operation description.
Device Operation
a)
Buck Mode
The most simple Buck circuit is shown in Figure 26 LED current
control in Buck mode is achieved by sensing the coil current in the
VIN
R1
SD1
sense resistor Rs, connected between the two inputs of a current
monitor within the control loop block. An output from the control loop
VAUXVIN
PWM
GI
drives the input of a comparator which drives the gate of the internal
NMOS switch transistor.
value is reached. At this point the switch is turned off and the current
flows via Rs, LED, coil and D1 back to VIN. When the coil current has
L1
LX
ADJ ZXLD1374 LX
FLAG
REF
STATUS
TADJ
SHP NC SGNDPGND
When the switch is on, current flows from VIN, via Rs, LED, coil and
switch to ground. This current ramps up until an upper threshold
ISM
C1
ramped down to a lower threshold value the switch is turned on again
and the cycle of events repeats, resulting in continuous oscillation.
The average current in the LED and coil is equal to the average of the
C2
100pF
GND
maximum and minimum threshold currents. The ripple current
(hysteresis) is equal to the difference between the thresholds.
Figure 26 Buck Configuration
The control loop maintains the average LED current at the set level
by adjusting the thresholds continuously to force the average current
+11V to
15V typ.
in the coil to the value demanded by the voltage on the ADJ pin. This
minimizes variation in output current with changes in operating
conditions.
tOFF
GATE
voltage
tON
0V
The control loop also attempts to minimize changes in switching
frequency by varying the level of hysteresis. The hysteresis has a
defined minimum (typ 5%) and a maximum (typ 20%), the frequency
may deviate from nominal in extreme conditions. Loop compensation
is achieved by a single external capacitor C1, connected between
SHP and SGND.
VIN + VF
Q1
Drain
voltage
0V
The control loop sets the duty cycle so that the sense voltage is
⎛ V ADJ ⎞
⎟
V SENSE = 0.218⎜⎜
⎟
⎝ VREF ⎠
Therefore,
ILED
⎛ 0.218 ⎞⎛ V ADJ ⎞
⎟⎜
⎟ (Buck mode) Equation 1
= ⎜⎜
⎟
⎟⎜
⎝ RS ⎠⎝ VREF ⎠
IPK
Coil &
LED
current
0A
If the ADJ pin is connected to the REF pin, this simplifies to
⎛ 0.218 ⎞
⎟ (Buck mode).
ILED = ⎜⎜
⎟
⎝ RS ⎠
Sense
voltage
VIN - VISM
Mean = 218mV
Figure 27 Operating Waveforms (Buck Mode)
ZXLD1374
Document number: DS35032 Rev. 3 - 2
15 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
a)
Boost and Buck-Boost Modes
A basic ZXLD1374 application circuit for Buck-Boost and Boost modes is shown in Figure 28.
Control in Boost and Buck-boost mode is achieved by sensing the coil
current in the series resistor Rs, connected between the two inputs of
a current monitor within the control loop block.
Buck-boost
Boost
VIN
R1
L1
An output from the control loop drives the input of a comparator which
VAUX VIN
PWM
GI
drives the gate of the internal NMOS switch transistor. In Boost and
Buck-boost modes, when the switch is on, current flows from VIN, via
Rs, coil and switch to ground. The switch current ramps up until an
upper threshold value is reached (see Figure 29). At this point the
ADJ ZXLD1374
switch is turned off and the drain voltage increases to either:
1) the LED chain voltage plus the forward voltage of D1 in Boost
RGI2
configuration,
or
SD1
LX
LX
FLAG
REF
STATUS
TADJ
SHP NC SGND PGND
RGI2
C1
ISM
COUT
C2
100pF
GND
2) the LED chain voltage plus the forward voltage of D1 plus
VIN in Buck-boost configuration.
Figure 28 Boost and Buck-Boost Configuration
The inductor current flows via Rs, coil, D1 and LED back to VIN
(Buck-boost mode), or GND (Boost mode). When the coil current has
ramped down to a lower threshold value the switch is turned on again
and the cycle of events repeats, resulting in continuous oscillation.
The feedback loop adjusts the NMOS switch duty cycle to stabilize
the LED current in response to changes in external conditions,
including input voltage and load voltage.
Loop compensation is
achieved by a single external capacitor C2, connected between SHP
and SGND. Note that in reality, a load capacitor COUT is used, so
that the LED current waveform shown is smoothed.
The average current in the coil is equal to the average of the
maximum and minimum threshold currents and the ripple current
(hysteresis) is equal to the difference between the thresholds. The
average current in the LED, ILED, is always less than IRS. The
feedback control loop adjusts the switch duty cycle, D, to achieve a
set point at the sense resistor. This controls IRS.
During the interval tOFF, the coil current flows through D1 and the LED
load.
During tON, the coil current flows through Q1, not the LEDs.
Therefore the set point is modified by D using a gating function to
control ILED indirectly. In order to compensate internally for the effect
of the gating function, a control factor, GI_ADJ is used. GI_ADJ is set
by a pair of external resistors, RGI1 and RGI2. (Figure 28.)
This allows the sense voltage to be adjusted to an optimum level for
Figure 29 Operating Waveforms
(Boost and Buck-Boost Modes)
power efficiency without significant error in the LED controlled current.
ZXLD1374
Document number: DS35032 Rev. 3 - 2
16 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
RGI1
⎞
⎛
GI _ ADJ = ⎜
⎟ Equation 2 (Boost and Buck-Boost modes)
RGI
1
+
RGI
2
⎠
⎝
The control loop sets the duty cycle so that the sense resistor current is
⎛ 0.225 ⎞⎛ GI _ ADJ ⎞⎛ V ADJ ⎞
⎟⎜
⎟ Equation 3 (Boost and Buck-Boost modes)
⎟⎜⎜
IRS = ⎜⎜
⎟
⎟
⎝ RS ⎠⎝ 1 − D ⎠⎝ VREF ⎠
IRS equals the coil current. The coil is connected only to the switch and the schottky diode. The schottky diode passes the LED current.
Therefore the average LED current is the coil current multiplied by the schottky diode duty cycle, 1-D.
⎛ 0.225 ⎞
⎛
⎞
⎟GI _ ADJ⎜ V ADJ ⎟ Equation 4 (Boost and Buck-Boost)
ILED = IRS (1 − D) = ⎜⎜
⎜
⎟
⎟
⎝ VREF ⎠
⎝ RS ⎠
This shows that the LED current depends on the ADJ pin voltage, the reference voltage and 3 resistor values (RS, RGI1 and RGI2). It is
independent of the input and output voltages.
If the ADJ pin is connected to the REF pin, this simplifies to
⎛ 0.225 ⎞
⎟GI _ ADJ (Boost and Buck-boost)
ILED = ⎜⎜
⎟
⎝ RS ⎠
Now ILED is dependent only on the 3 resistor values.
Considering power dissipation and accuracy, it is useful to know how the mean sense voltage varies with input voltage and other parameters.
⎛ GI _ ADJ ⎞⎛ V ADJ ⎞
⎟ Equation 5 (Boost and Buck-boost)
⎟⎜⎜
VRS = IRS RS = 0.225⎜
⎟
⎝ 1 − D ⎠⎝ VREF ⎠
This shows that the sense voltage varies with duty cycle in Boost and Buck-boost configurations.
Application Circuit Designs
External component selection is driven by the characteristics of the load and the input supply, since this will determine the kind of topology being
used for the system. Component selection begins with the current setting procedure, the inductor/frequency setting selection. Finally after
selecting the freewheeling diode and the output capacitor (if needed), the application section will cover the PWM dimming and thermal feedback.
The full procedure is greatly accelerated by the web Calculator spreadsheet, which includes fully automated component selection, and is
available on the Diodes web site. However the full calculation is also given here.
Please note the following particular feature of the web Calculator. The GI ratio can be set for Automatic calculation, or it can be fixed at a
chosen value. When optimizing a design, it is best first to optimize for the chosen voltage range of most interest, using the Automatic setting. In
order to subsequently evaluate performance of the circuit over a wider input voltage range, fix the GI ratio in the Calculator input field, and then
set the desired input voltage range.
Some components depend upon the switching frequency and the duty cycle. The switching frequency is regulated by the ZXLD1374 to a large
extent, depending upon conditions. This is discussed in a later paragraph dealing with coil selection.
ZXLD1374
Document number: DS35032 Rev. 3 - 2
17 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
Duty Cycle Calculation and Topology Selection
The duty cycle is a function of the input and output voltages. Approximately, the MOSFET switching duty cycle is
DBUCK ≈
V OUT
VIN
DBOOST ≈
DBB ≈
for Buck
V OUT − VIN
V OUT
V OUT
V OUT + VIN
for Boost
Equation 6
for Buck-Boost
Because D must always be a positive number less than 1, these equations show that
V OUT < VIN
for Buck (voltage step-down)
V OUT > VIN
for Boost (voltage step-up)
V OUT > or = or < VIN
for Buck-boost (voltage step-down or step-up)
This allows us to select the topology for the required voltage range.
More exact equations are used in the web Calculator. These are:
DBUCK =
V OUT + VF + IOUT (RS + RCOIL )
VIN + VF − VDSON
DBOOST =
DBB =
where
V OUT − VIN + IIN (RS + RCOIL ) + VF
VOUT + VF − VDSON
V OUT + VF + (IIN + IOUT )(RS + RCOIL )
V OUT + VIN + VF − VDSON
for Buck
for Boost
Equation 7
for Buck-Boost
VF
= schottky diode forward voltage, estimated for the expected coil current, ICOIL
VDSON
= MOSFET drain source voltage in the ON condition (dependent on RDSON and drain current = ICOIL)
RCOIL
= DC winding resistance of L1
The additional terms are relatively small, so the exact equations will only make a significant difference at lower operating voltages at the input
and output, i.e. low input voltage or a small number of LEDs connected in series. The estimates of VF and VDSON depend on the coil current.
The mean coil current, ICOIL depends upon the topology and upon the mean terminal currents as follows:
ICOIL = ILED
for Buck
ICOIL = IIN
for Boost
ICOIL = IIN + ILED
for Buck-Boost
Equation 8
ILED is the target LED current and is already known. IIN will be calculated with some accuracy later, but can be estimated now from the electrical
power efficiency.
ZXLD1374
Document number: DS35032 Rev. 3 - 2
18 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
If the expected efficiency is roughly 90%, the output power POUT is 90% of the input power, PIN, and the coil current is estimated as follows.
POUT
≈ 0.9 PIN
or
ILED N VLED ≈ 0.9 IIN VIN
where N is the number of LEDs connected in series, and VLED is the forward voltage drop of a single LED at ILED.
So
IIN ≈
ILED N VLED
0.9 VIN
Equation 9
Equation 9 can now be used to find ICOIL in Equation 8, which can then be used to estimate the small terms in Equation 7. This completes the
calculation of Duty Cycle and the selection of Buck, Boost or Buck-boost topology.
An initial estimate of duty cycle is required before we can choose a coil. In Equation 7, the following approximations are recommended:
VF
= 0.5V
IIN × (RS+RCOIL)
= 0.5V
IOUT × (RS+RCOIL)
= 0.5V
VDSON
= 0.1V
(IIN+IOUT)(RS+RCOIL)
= 1.1V
Then Equation 7 becomes
VOUT + 1
VIN + 0.4
V OUT − VIN + 1
DBOOST ≈
VOUT + 0.4
DBUCK ≈
DBB ≈
V OUT + 1.6
V OUT + VIN + 0.4
for Buck
for Boost
Equation 7a
for Buck-Boost
Setting the LED Current
The LED current requirement determines the choice of the sense resistor Rs. This also depends on the voltage on the ADJ pin and the voltage
on the GI pin, according to the topology required.
The ADJ pin may be connected directly to the internal 1.25V reference (VREF) to define the nominal 100% LED current. The ADJ pin can also be
driven with an external dc voltage between 125mV and 2.5V to adjust the LED current proportionally between 10% and 200% of the nominal
value.
For a divider ratio GI_ADJ greater than 0.65V, the ZXLD1374 operates in Buck mode when VADJ = 1.25V. If GI_ADJ is less than 0.65V (typical),
the device operates in Boost or buck-Boost mode, according to the load connection. This 0.65V threshold varies in proportion to VADJ, i.e., the
Buck mode threshold voltage is 0.65 VADJ /1.25V.
ADJ and GI are high impedance inputs within their normal operating voltage ranges. An internal 1.3V clamp protects the device against
excessive input voltage and limits the maximum output current to approximately 4% above the maximum current set by VREF if the maximum
input voltage is exceeded.
ZXLD1374
Document number: DS35032 Rev. 3 - 2
19 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
Buck Topology
RS
In Buck mode, GI is connected to ADJ as in Figure 30 (for simplicity TADJ is
not shown. However if not used should be connected to REF).
VIN
REF
The LED current depends only upon RS, VADJ and VREF. From Equation 1 above,
⎛ 0.218 ⎞⎛ V ADJ ⎞
⎟⎜
⎟
RSBuck = ⎜⎜
⎟⎜
⎟
⎝ ILED ⎠⎝ VREF ⎠
ISM
Equation 10
ADJ
If ADJ is directly connected to VREF, this becomes:
RSBuck
GI
⎛ 0.218 ⎞
⎟⎟
= ⎜⎜
⎝ ILED ⎠
SGND
Boost and Buck-Boost Topology
In Boost and Buck-boost mode GI is connected to ADJ through a voltage divider as in
figure 31 (for simplicity TADJ is not shown. However if not used should be connected to
Figure 30 Buck Configuration
REF).
RS
The LED current depends upon the resistors, RS, RGI1, and RGI2 as in Equations 4 and
2 above. There is more than one degree of freedom. That is to say, there is not a unique
VIN
solution. From Equation 4,
⎛ 0.225 ⎞
⎛
⎞
⎟GI _ ADJ⎜ V ADJ ⎟
RSBoostBB = ⎜⎜
⎟
⎜
⎟
⎝ ILED ⎠
⎝ VREF ⎠
REF
Equation 11
ADJ
If ADJ is connected to REF, this becomes
RSBoostBB
ISM
R GI2
⎛ 0.225 ⎞
⎟⎟GI _ ADJ
= ⎜⎜
⎝ ILED ⎠
GI
R GI1
GI_ADJ is given by Equation 2, repeated here for convenience:
SGND
RGI1
⎛
⎞
GI _ ADJ = ⎜
⎟
⎝ RGI1 + RGI2 ⎠
Figure 31 Boost and Buck-Boost
Connection
Note that from considerations of ZXLD1374 input bias current, the recommended limits for RGI1 are:
22kΩ < RGI1 < 100kΩ
Equation 12
The additional degree of freedom allows us to select GI_ADJ within limits but this may affect overall performance a little. As mentioned above,
the working voltage range at the GI pin is restricted. The permitted range of GI_ADJ in Boost or Buck-boost configuration is
0.2 < GI_ADJ < 0.5
Equation 13
The mean voltage across the sense resistor is
VRS = ICOIL RS
Equation 14
Note that if GI_ADJ is made larger, these equations show that RS is increased and VRS is increased. Therefore, for the same coil current, the
dissipation in RS is increased. So, in some cases, it is better to minimize GI_ADJ. However, consider Equation 5. If ADJ is connected to REF,
this becomes
⎛ GI _ ADJ ⎞
⎟
VRS = 0.225⎜
⎝ 1− D ⎠
This shows that VRS becomes smaller than 225mV if GI_ADJ < 1 - D. If also D is small, VRS can become too small. For example if D = 0.2, and
GI_ADJ is the minimum value of 0.2, then VRS becomes 0.225* 0.2 / 0.8 = 56.25mV. This will increase the LED current error due to small offsets
in the system, such as mV drop in the copper printed wiring circuit, or offset uncertainty in the ZXLD1371. If now, GI_ADJ is increased to 0.4 or
0.5, VRS is increased to a value greater than 100mV.
ZXLD1374
Document number: DS35032 Rev. 3 - 2
20 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
This will give small enough ILED error for most practical purposes. Satisfactory operation will be obtained if VRS is more than about 80mV. This
means GI_ADJ should be greater than (1-DMIN) * 80/225 = (1- DMIN) * 0.355.
There is also a maximum limit on VRS which gives a maximum limit for GI_ADJ. If VRS exceeds approximately 300mV, or 133% of 225mV, the
STATUS output may indicate an over-current condition. This will happen for larger DMAX. Therefore, together with the requirement of Equation
13, the recommended range for GI_ADJ is
0.355 ( 1-DMIN) < GI_ADJ < 1.33 ( 1-DMAX )
Equation 15
An optimum compromise for GI_ADJ has been suggested, i.e.
GI_ADJAUTO = 1 - DMAX
Equation 16
This value has been used for the “Automatic” setting of the web Calculator. If 1-DMAX is less than 0.2, then GI_ADJ is set to 0.2. If 1- DMAX is
greater than 0.5 then GI_ADJ is set to 0.5.
Once GI_ADJ has been selected, a value of RGI1 can be selected from Equation 12. Then RGI2 is calculated as follows, rearranging
Equation 2:
⎛ 1 − GI _ ADJ ⎞
RGI1 = RGI1 ⎜⎜
⎟⎟
⎝ GI _ ADJ ⎠
Equation 17
For example to drive 12 LEDS at a current of 350mA from a 12V supply requires Boost configuration. Each LED has a forward voltage of 3.2V
at 350mA, so Vout = 3.2*12 = 38.4V. From Equation 6, the duty cycle is approximately
(VOUT − VIN) = (38.4 − 12) = 0.6875
38.4
V OUT
From Equation 16, we set GI_ADJ to 1 – D = 0.3125.
If RGI1 = 33kΩ, then from Equation 17, RGI2 = 33000 * ( 1 -0.3125 ) / 0.3125 = 72.6kΩ. Let us choose the preferred value RGI2 = 75kΩ. Now
GI_ADJ is adjusted to the new value, using Equation 2.
RGI1
33k
⎛
⎞
GI _ ADJ = ⎜
= 0.305
⎟=
⎝ RGI1 + RGI2 ⎠ 33k + 75K
Now we calculate Rs from Equation 11. Assume ADJ is connected to REF.
⎛ 0.225 ⎞
⎛
⎞ 0.225
⎟GI _ ADJ⎜ V ADJ ⎟ =
* 0.305 = 0.196Ω
RSBoostBB = ⎜⎜
⎟
⎜
⎟
0.35
⎝ ILED ⎠
⎝ VREF ⎠
A preferredvalue of RSBoostBB = 0.2Ω will give the desired LED current with an error of 2% due to the preferred value selection.
Table 1 shows typical resistor values used to determine the GI_ADJ ratio with E24 series resistors.
Table 1
GI Ratio
RGI1
RG2
0.2
30kΩ
120kΩ
0.25
33kΩ
100kΩ
91kΩ
0.3
39kΩ
0.35
30kΩ
56kΩ
0.4
100kΩ
150kΩ
0.45
51kΩ
62kΩ
0.5
30kΩ
30kΩ
This completes the LED current setting.
ZXLD1374
Document number: DS35032 Rev. 3 - 2
21 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
Inductor Selection and Frequency Control
The selection of the inductor coil, L1, requires knowledge of the switching frequency and current ripple, and also depends on the duty cycle to
some extent. In the hysteretic converter, the frequency depends upon the input and output voltages and the switching thresholds of the current
monitor. The peak-to-peak coil current is adjusted by the ZXLD1374 to control the frequency to a fixed value. This is done by controlling the
switching thresholds within particular limits. This effectively much reduces the overall frequency range for a given input voltage range. Where
the input voltage range is not excessive, the frequency is regulated to approximately 390kHz. This is helpful in terms of EMC and other system
requirements.
For larger input voltage variation, or when the choice of coil inductance is not optimum, the switching frequency may depart from the regulated
value, but the regulation of LED current remains successful. If desired, the frequency can to some extent be increased by using a smaller
inductor, or decreased using a larger inductor. The web Calculator will evaluate the frequency across the input voltage range and the effect of
this upon power efficiency and junction temperatures.
Determination of the input voltage range for which the frequency is regulated may be required. This calculation is very involved, and is not given
here. However the performance in this respect can be evaluated within the web Calculator for the chosen inductance.
The inductance is given as follows in terms of peak-to-peak ripple current in the coil, ΔIL and the MOSFET on time, tON.
L1 = {VIN − N VLED − IOUT (RDSON + RCOIL + RS )}
L1 = {VIN − IIN (RDSON + RCOIL + RS )}
tON
ΔIL
tON
ΔIL
L1 = {VIN − (IIN + IOUT )(RDSON + RCOIL + RS )}
for Buck
for Boost
tON
ΔIL
Equation 18
for Buck-Boost
Therefore In order to calculate L1, we need to find IIN, tON, and ΔIL. The effects of the resistances are small and will be estimated.
IIN is estimated from Equation 9.
tON is related to switching frequency, f, and duty cycle, D, as follows:
tON =
D
f
Equation 19
As the regulated frequency is known, and we have already found D from Equation 7 or the approximation Equation 7b, this allows calculation of
tON.
The ZXLD1374 sets the ripple current, ΔIL, to between nominally 10% and 30% of the mean coil current, ICOIL, which is found from Equation 8.
The device adjusts the ripple current within this range in order to regulate the switching frequency. We therefore need to use a ΔIL value of 20%
of ICOIL to find an inductance which is optimized for the input voltage range. The range of ripple current control is also modulated by other circuit
parameters as follows.
⎧⎪
⎛ V ADJ ⎞⎫⎪ 1 − D
⎟⎬
ICOIL
ΔILMAX = ⎨0.06 + 0.24⎜⎜
⎟
⎪⎩
⎝ VREF ⎠⎪⎭ GI _ ADJ
⎧⎪
⎛ V ADJ ⎞ ⎫⎪ 1 − D
⎟⎟ ⎬
ΔILMIN = ⎨0.02 + 0.08⎜⎜
ICOIL
⎪⎩
⎝ VREF ⎠ ⎪⎭ GI _ ADJ
Equation 20
⎧⎪
⎛ V ADJ ⎞⎫⎪ 1 − D
⎟⎬
ICOIL
ΔILMID = ⎨0.04 + 0.16⎜⎜
⎟
⎪⎩
⎝ VREF ⎠⎪⎭ GI _ ADJ
If ADJ is connected to REF, this simplifies to
1− D
ICOIL
GI _ ADJ
1− D
ΔILMIN = 0.1
ICOIL
GI _ ADJ
1− D
ΔILMID = 0.2
ICOIL
GI _ ADJ
ΔILMAX = 0.3
Equation 20a
where ΔILMID is the value we must use in Equation 18. We have now established the inductance value.
ZXLD1374
Document number: DS35032 Rev. 3 - 2
22 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
The chosen coil should saturate at a current greater than the peak sensed current. This saturation current is the DC current for which the
inductance has decreased by 10% compared to the low current value.
Assuming ±10% ripple current, we can find this peak current from Equation 8, adjusted for ripple current:
ICOILPEAK = 1.1 ILED
for Buck
ICOILPEAK = 1.1 IINMAX
for Boost
ICOILPEAK = 1.1 IINMAX + ILED
for Buck-boost
Equation 21
where IINMAX is the value of IIN at minimum VIN.
The mean current rating is also a factor, but normally the saturation current is the limiting factor.
The following websites may be useful in finding suitable components
www.coilcraft.com
www.niccomp.com
www.wuerth-elektronik.de
Diode Selection
For maximum efficiency and performance, the rectifier (D1) should be a fast low capacitance Schottky diode* with low reverse leakage at the
maximum operating voltage and temperature. The Schottky diode also provides better efficiency than silicon PN diodes, due to a combination of
lower forward voltage and reduced recovery time.
It is important to select parts with a peak current rating above the peak coil current and a continuous current rating higher than the maximum
output load current. In particular, it is recommended to have a voltage rating at least 15% higher than the maximum LX voltage to ensure safe
operation during the ringing of the switch node and a current rating at least 10% higher than the average diode current. The power rating is
verified by calculating the power loss through the diode.
The higher forward voltage and overshoot due to reverse recovery time in silicon diodes will increase the peak voltage on the LX pin. If a silicon
diode is used, care should be taken to ensure that the total voltage appearing on the LX pin, including supply ripple, does not exceed the
specified maximum value.
*A suitable Schottky diode would be PDS3100 (Diodes Inc).
Output Capacitor
An output capacitor may be required to limit interference or for specific EMC purposes. For Boost and Buck-boost regulators, the output
capacitor provides energy to the load when the freewheeling diode is reverse biased during the first switching subinterval. An output capacitor in
a Buck topology will simply reduce the LED current ripple below the inductor current ripple. In other words, this capacitor changes the current
waveform through the LED(s) from a triangular ramp to a more sinusoidal version without altering the mean current value.
In all cases, the output capacitor is chosen to provide a desired current ripple of the LED current (usually recommended to be less than 40% of
the average LED current).
Buck:
COUTPUT =
ΔIL −PP
x
8 xf SW rLED x ΔILED−PP
Boost and Buck-boost
COUTPUT =
DxILED
x
f SW rLED x ΔILED −PP
where:
•
ΔIL is the ripple of the inductor current, usually ± 20% of the average sensed current
•
ΔILED is the ripple of the LED current, it should be <40% of the LEDs average current
•
fsw is the switching frequency (from graphs and calculator)
•
rLED is the dynamic resistance of the LEDs string (n times the dynamic resistance of the single LED from the
datasheet of the LED manufacturer).
ZXLD1374
Document number: DS35032 Rev. 3 - 2
23 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
Output Capacitor (cont.)
The output capacitor should be chosen to account for derating due to temperature and operating voltage. It must also have the necessary RMS
current rating. The minimum RMS current for the output capacitor is calculated as follows:
Buck
ILED − PP
IOUTPUT −RMS =
12
Boost and Buck-Boost
IOUTPUT −RMS = ILED
DMAX
1− DMAX
Ceramic capacitors with X7R dielectric are the best choice due to their high ripple current rating, long lifetime, and performance over the voltage
and temperature ranges.
Input Capacitor
The input capacitor can be calculated knowing the input voltage ripple ΔVIN-PP as follows:
Buck
CIN =
Dx(1− D)xILED
f SW x ΔVIN−PP
use D = 0.5 as worst case
Boost
CIN =
ΔIL −PP
8 Xf SW x ΔVIN−PP
Buck-boost
CIN =
DxILED
f SW x ΔVIN−PP
use D = DMAX as worst case
The minimum RMS current for the output capacitor is calculated as follows:
Buck
ICIN−RMS = ILED x Dx (1 − D)
use D = 0.5 as worst case
Boost
ICIN−RMS =
IL −PP
12
Buck-Boost
ICIN−RMS = ILED x
D
1− D
ZXLD1374
Document number: DS35032 Rev. 3 - 2
use D = DMAX as worst case
24 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
Over-Temperature Shutdown
The ZXLD1374 incorporates an over-temperature shutdown circuit to protect against damage caused by excessive die temperature. A warning
signal is generated on the STATUS output when die temperature exceeds +125°C nominal and the output is disabled when die temperature
exceeds 150°C nominal. Normal operation resumes when the device cools back down to +125°C.
Flag/Status Outputs
The FLAG/STATUS outputs provide a warning of extreme operating or fault conditions. FLAG is an open-drain logic output, which is normally
off, but switches low to indicate that a warning, or fault condition exists. STATUS is a DAC output, which is normally high (4.5V), but switches to
a lower voltage to indicate the nature of the warning/fault.
Table 2
Conditions monitored, the method of detection and the nominal STATUS output voltage are given in the following table (Note 15):
Warning/Fault Condition
Severity
(Note 16)
Monitored
Parameters
Normal Operation
FLAG
Nominal STATUS Voltage
H
4.5V
1
VAUX < 5.6V
L
4.5V
2
VIN < 5.6V
L
3.6V
Output Current Out of Regulation
(Note 17)
2
VSHP outside normal voltage
range
L
3.6V
Driver Stalled with Switch ‘on’, or ‘off’
(Note 18)
2
tON, or tOFF > 100µs
L
3.6V
Switch Over-Voltage
3
LX voltage > 60V
L
2.7
Device Temperature Above Maximum
Recommended Operating Value
4
TJ > +125°C
L
1.8V
Sense Resistor Current IRS Above Specified
Maximum
5
VSENSE > 0.375V
L
0.9V
Average Switch > 1.5A
5
ILX > 1.5A
L
0.9V
Supply Under-Voltage
Notes:
15. These STATUS pin voltages apply for an input voltage, VIN, of 7.5V < VIN < 60V. Below 7.5V the STATUS pin voltage levels reduce and therefore may
not report the correct status. For 6.3V < VIN < 7.5V the flag pin still reports an error by going low. At low VIN in Boost and Buck-boost modes an overcurrent status may be indicated when operating at high boost ratios -– this due to the feedback loop increasing the sense voltage.
16. Severity 1 denotes lowest severity.
17. This warning will be indicated if the output power demand is higher than the available input power; the loop may not be able to maintain regulation.
18. This warning will be indicated if the gate pin stays at the same level for greater than 100µs (e.g. the output transistor cannot pass enough current
to reach the upper switching threshold).
ZXLD1374
Document number: DS35032 Rev. 3 - 2
25 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
FLAG VOLTAGE
Application Information (cont.)
VR EF
0V
4.5V
Normal
Operations
VAUX
UVLO
STAT US VOLTA GE
3.6V
- VIN UVLO
- STALL
- OU T of REG
2.7V
ZXLD1374
Switch OV
1.8V
Over
Temperature
0.9V
Over
C urrent
0A
0
1
2
3
5
4
SEVERITY
Figure 32 Status Levels
In the event of more than one fault/warning condition occurring, the higher severity condition will take precedence. E.g. ‘Excessive coil current’
and ‘Out of regulation’ occurring together will produce an output of 0.9V on the STATUS pin.
If VADJ>1.7V, VSENSE may be greater than the excess coil current threshold in normal operation and an error will be reported. Hence, STATUS
and FLAG are only guaranteed for VADJ<=VREF.
Diagnostic signals should be ignored
VREF
FLAG
during the device start – up for 100μs.
The device start up sequence will be
initiated both during the first power on of
the device or after the PWM signal is kept
Out of
regulation
STATUS
low for more than 15ms, initiating the
standby state of the device.
In particular, during the first 100μs the
Overcurrent
then an out-of-regulation status.
These
two events are due to the charging of the
inductor and are not true fault conditions.
Coil current (A)
diagnostic is signaling an over-current
1.4
1.2
1
0.8
0.6
0.4
0.2
0
0
20
40
60
80
100
time (µs)
120
140
160
180
200
Figure 33 Diagnostic During Start-Up
ZXLD1374
Document number: DS35032 Rev. 3 - 2
26 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
Reduced Input Voltage Operation
To facilitate operation in applications that have large transient reductions in system supply voltage, the ZXLD1374 is capable of operating down
to input voltages as low as 6.3V. Care must be taken when operating at these lower supply voltages to ensure that the internal MOSFET is
correctly enhanced and that the boosting ratio is not increased to excessive amounts where both the duty cycle and peak-switch current limits
are not exceeded. The device will operate down to 6.3V, but for reliable start up VIN must be higher than 6.5V plus any margins for any noise
that may occur on the supply lines.
In Buck-boost and Boost modes (most common topologies for applications likely to require transient operation down to supply voltages
approaching 6V) as the input voltage reduces then the peak switch current will increase the ZXLD1374 compensates for this by allowing the
sense voltage to increase while maintaining regulation of the LED current. However if the boost ratio (switch output voltage/input voltage) is
increased too much then the sense voltage could be increased too much causing an over-current flag to be triggered and/or loss of regulation.
In addition to this, increased power dissipation will occur in the internal MOSFET switch. One way of overcoming this is to apply a boot-strap
network to the VAUX pin – see next section.
If the ZXLD1374 is used in buck mode at low voltages then the boot-strap network cannot be implemented and some loss of regulation may
occur at input voltages approaching 6V driving 1 LED.
When using the ZXLD1374 in applications with transient input voltage excursions we recommend using the web calculator to optimize operation
over the normal operating band. Then change the input range to include the transient excursion while keeping the optimized component
selection to check expected function during the transient input voltage conditions.
Boosting VAUX Supply Voltage in Boost and Buck-Boost Mode
A boot-strap boosting technique can be used to increase the gate drive voltage at low input voltage. See figure 34 for circuit diagram. This can
be particularly important for extended use at low input voltages as this is when the switch current will be at its greatest – resulting in greatest
heat generation within the MOSFET.
Figure 34. Bootstrap Circuit for Boost and Buck-Boost Low Voltage Operations
The Bootstrap circuit guarantees that the MOSFET is fully enhanced reducing both the power dissipation and the risk of thermal runaway of the
MOSFET itself. The bootstrap circuit consists of an extra diode D2 and decoupling capacitor C8 which are used to generate a boosted voltage
at VAUX. This enables the device to operate with full output current when VIN is at the minimum value of 6.3V. The resistor R13 can be used to
limit the current in the bootstrap circuit in order to reduce the impact of the circuit itself on the LED accuracy. A typical value would be 100 ohms.
The impact on the LED current is usually a decrease of maximum 5% compared to the nominal current value set by the sense resistor.
The Zener diode may be used to limit the voltage on the VAUX pin to less than 60V.
Due to the increased number of components and the loss of current accuracy, the bootstrap circuit is recommended only when the system has to
operate continuously in conditions of low input voltage (between 6.3 and 8V) and high load current.
If lower transient voltages are expected then the ZXLD1371 LED Driver-controller could be used, whose input voltage extends down to 5V.
ZXLD1374
Document number: DS35032 Rev. 3 - 2
27 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
Over-Voltage Protection
The ZXLD1374 is inherently protected against open-circuit load when used in Buck configuration. However care has to be taken with opencircuit load conditions in Buck-boost or Boost configurations. This is because in these configurations there is only an over-voltage FLAG but no
internal open-circuit protection mechanism for the internal MOSFET. In this case an Over-Voltage-Protection (OVP) network should be provided
to the MOSFET to avoid damage due to open circuit conditions. This is shown in Figure 35 below, highlighted in the dotted blue box.
Figure 35 OVP Circuit
The zener voltage is determined according to: VZ = VLEDMAX +10%. If the LX pin voltage exceeds VZ the gate of MOSFET Q1 will rise turning Q1
on. This will pull the PWM pin low and disable the LX output until the voltage on the LX falls below Vz. If the LX pin remains above VZ for longer
than 20ms then the ZXLD1374 will enter into a shutdown state.
Care should be taken such that the maximum gate voltage of the Q1 MOSFET is not exceeded.
An alternative solution for OVP function is to use the diagnostic section of the ZXLD1374 to initiate the disabling of the LX pin. For example, a
microcontroller could be used to respond to the FLAG and the status pins, and if an over-voltage state is indicated, the microcontroller could
switch the device off by pulling the PWM signal low.
ZXLD1374
Document number: DS35032 Rev. 3 - 2
28 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
LED Current Dimming
The ZXLD1374 has 3 dimming methods for reducing the average LED current
1.
Analog dimming using the ADJ pin
2.
PWM dimming using the PWM pin
3.
Analog dimming for thermal protection using the TADJ pin.
Analog Dimming
The ZXLD1374 has a clamp on the ADJ pin to prevent over-driving of the LED current which results in the maximum voltage being applied to
internal circuitry is the reference voltage. This provides a 10:1 dynamic range of dc LED current adjustment.
The equation for DC dimming of the LED current is approximately:
⎛ V ADJ ⎞
⎟
ILED _ DIM = ILED _ NOM ⎜⎜
⎟
⎝ VREF ⎠
Where
ILED_DIM is the dimmed LED current
ILED_NOM is the LED current with VADJ = 1.25V
One consequence of DC dimming is that as the ADJ pin voltage is reduced the sense voltage will also be reduced which has an impact on
accuracy and switching frequency especially at lower ADJ pin voltages.
750
750
LED CURRENT (mA)
600
Switching
Frequency
450
450
300
300
TA=25°C
VAUX =VIN =12V
2 LEDs
L=33µH
RS=300mΩ
150
0
0
0.25
0.5
0.75
ADJ VOLTAGE (V)
1
150
SWITCHING FREQUENCY (kHz)
600
0
1.25
Figure 36 LED Current and Switching Frequency vs. ADJ Voltage
ZXLD1374
Document number: DS35032 Rev. 3 - 2
29 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
PWM Output Current Control & Dimming
The ZXLD1374 has a dedicated PWM dimming input that allows a wide dimming frequency range from 100Hz to 1kHz with 1000:1 resolution;
however higher dimming frequencies can be used – at the expense of dimming dynamic range and accuracy.
Typically, for a PWM frequency of 1kHz, the error on the current linearity is lower than 5%; in particular the accuracy is better than 1% for PWM
from 5% to 100%. This is shown in the graph below for Buck mode:
15.0%
1500
1250
VIN = 24V
TA = 25°C
fPWM = 1kHz
10.0%
1000
7.5%
750
ILED
5.0%
500
2.5%
250
Normalized LED
Current Error
0.0%
0%
10%
20%
30%
40%
50%
60%
LED current (mA)
Normalized LED current error
12.5%
70%
80%
90%
0
100%
PWM duty cycle
Figure 37 LED Current Linearity and Accuracy with PWM Dimming at 1kHz
For a PWM frequency of 100Hz, the error on the current linearity is lower than 2.5%; it becomes negligible for PWM greater than 5%. This is
15.0%
1500
12.5%
1250
VIN = 24V
TA = 25°C
fPWM = 100Hz
10.0%
1000
ILED
7.5%
750
5.0%
500
2.5%
LED current (mA)
Normalized LED current error
shown in the graph below:
250
Normalized LED
Current Error
0.0%
0%
10%
20%
30%
40%
50%
60%
PWM duty cycle
70%
80%
90%
0
100%
Figure 38 LED Current Linearity and Accuracy with PWM Dimming at 100Hz
ZXLD1374
Document number: DS35032 Rev. 3 - 2
30 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
PWM Output Current Control & Dimming (cont.)
The PWM pin is designed to be driven by both 3.3V and 5V logic levels. It can be driven also by an open drain/collector transistor. In this case
the designer can either use the internal pull-up network or an external pull-up network in order to speed-up PWM transitions, as shown in the
Boost/ Buck-Boost section.
LED current can be adjusted digitally, by applying a low frequency PWM logic signal to the PWM pin to turn the controller on and off. This will
produce an average output current proportional to the duty cycle of the control signal. During PWM operation, the device remains powered up
and only the output switch is gated by the control signal.
The PWM signal can achieve very high LED current resolution. In fact, dimming down from 100% to 0, a minimum pulse width of 5µs can be
achieved resulting in very high accuracy. While the maximum recommended pulse is for the PWM signal is10ms.
Figure 41 PWM Dimming Minimum and Maximum Pulse
Standby Mode
The device can be put in standby by taking the PWM pin to a voltage below 0.4V for a time exceeding 20ms (15ms nominal). In the shutdown
state, most of the circuitry inside the device is switched off and residual quiescent current will be typically 90µA. In particular, the Status pin will
go down to GND while the FLAG and REF pins will stay at their nominal values.
Figure 42 Stand-By State from PWM Signal
ZXLD1374
Document number: DS35032 Rev. 3 - 2
31 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
Thermal Control of LED Current
For thermal control of the LEDs, the ZXLD1371 monitors the voltage on the TADJ pin and reduces output current if the voltage on this pin falls
below 625mV. An external NTC thermistor and resistor can therefore be connected as shown below to set the voltage on the TADJ pin to
625mV at the required temperature threshold. This will give 100% LED current below the threshold temperature and a falling current above it as
shown in the graph. The temperature threshold can be altered by adjusting the value of Rth and/or the thermistor to suit the requirements of the
chosen LED.
The Thermal Control feature can be disabled by connecting TADJ to REF.
Here is a simple procedure to design the thermal feedback circuit:
1. Select the temperature threshold TTHRESHOLD at which the current must start to decrease
2. Select the Thermistor TH1 (both resistive value at +25°C and beta)
3. Select the value of the resistor RTH as RTH = TH1 at TTHRESHOLD
Figure 43 Thermal Feedback Network
For example,
1.
Temperature threshold TTHRESHOLD = +70°C
2.
TH1 = 10kΩ at 25˚C and beta= 3500
3.
RTH = TH1 at TTHRESHOLD = 3.3kΩ
ZXLD1374
Document number: DS35032 Rev. 3 - 2
Æ
TH1 = 3.3kΩ at +70°C
32 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
PCB Layout Considerations
PCB layout is a fundamental activity to get the most of the device in all configurations. In the following section it is possible to find some
important insight to design with the ZXLD1374 both in Buck and Buck-Boost/Boost configurations.
Figure 44 Circuit Layout
Here are some considerations useful for the PCB layout:
-
In order to avoid ringing due to stray inductances, the inductor L1, the anode of D1 and the LX pin should be placed as close together as
possible.
-
The shaping capacitor C1 is fundamental for the stability of the control loop. To this end it should be placed no more than 5mm from the
-
SHP pin.
Input voltage pins, VIN and VAUX, need to be decoupled. It is recommended to use two ceramic capacitors of 2.2µF, X7R, 100V (C3 and
C4). In addition to these capacitors, it is suggested to add two ceramic capacitors of 1µF, X7R, 100V each (C2, C8), as well as a further
decoupling capacitor of 100nF close to the VIN/VAUX pins (C9) the device is used in Buck mode, or can be driven from a separate
supply.
-
Ensure that there is a large enough thermal mass to keep the thermal impedance between junction and ambient to keep the ZXLD1374
junction temperature below +125°C. On a 2 layer board this means putting enough vias from the landing pad of the TSSOP-20EP
exposed pad through to the bottom layer.
ZXLD1374
Document number: DS35032 Rev. 3 - 2
33 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
Thermal Impedance
Below is shown the thermal impedance of the ZXLD1374EST20 on a High Effective Thermal Conductivity Test Board" according JESD51.
4
3.5
Power dissipation (mW)
3
2.5
2
1.5
1
0.5
0
-40
-25
-10
5
20
35
50
65
80
95
110
Ambient temperature (°C)
Figure 45 Power Derating Curve
The power dissipation capability of the ZXLD1374 will vary on ambient temperature, effectiveness of any heat sinking, heat generated by
components around the ZXLD1374 (inductors, rectifiers, resistors etc) and air flow.
ZXLD1374
Document number: DS35032 Rev. 3 - 2
34 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
1.5A Buck LED Driver
In this application example, ZXLD1374 is connected
as a Buck LED driver with schematic and parts list
shown below. The LED driver is able to deliver 1.5A of
LED current to single or multiple LEDs in series with
input voltage ranged from 10V to 50V. In order to
achieve high efficiency under high LED current, Super
Barrier Rectifier (SBR) with low forward voltage is
used as free wheeling rectifier.
With only a few extra components, the ZXLD1374
LED driver is able to deliver LED power of greater
than 60W. This is suitable for applications which
require high LED power likes high power down
lighting, wall washer, automotive LED lighting etc.
Figure 46 Application Circuit of 1.5A Buck LED Driver
Bill of Material
Ref No.
Value
Part No.
Manufacturer
Diodes Inc
U1
60V 1.5A LED driver
ZXLD1374
D1
100V 3A SBR
SBR3U100
Diodes Inc
L1
33µH 4.2A
744770933
Wurth Electronik
C1
100pF 50V
SMD 0805/0603
Generic
C2
1µF 100V X7R
SMD1206
Generic
C3 C4 C5
2.2µF 100V X7R
SMD1210
Generic
R1 R2
300mΩ 1%
SMD1206
Generic
R3
4.7Ω
SMD1206
Generic
Typical Performance
LED Current vs Input Voltage
Efficiency vs Input Voltage
100%
1600
90%
70%
LED Current (mA)
Efficiency (%)
80%
60%
50%
40%
1 LED VF=3.4V
3 LED VF=9.8V
5 LED VF=16V
30%
20%
1200
800
1 LED VF=3.4V
3 LED VF=9.8V
5 LED VF=16V
400
10%
0%
10
15
20
25
30
35
40
45
50
Input Voltage (V)
Document number: DS35032 Rev. 3 - 2
10
15
20
25
30
35
40
45
50
Input Voltage (V)
Figure 47 Efficiency
ZXLD1374
0
Figure 48 Line Regulation
35 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
350mA Boost LED Driver
In this application example, ZXLD1374 is
connected as a Boost LED driver with
schematic and parts list shown below. The
LED driver is able to deliver 350mA of LED
current into 12 high brightness LED with
input voltage ranged from 16V to 28V.
Overall high efficiency of 92%+ make it ideal
for applications likes solar LED street lighting
and general LED illuminations.
Figure 49 Application Circuit of 350mA Boost LED Driver
Bill of Material
Ref No.
Value
Part No.
Manufacturer
U1
60V LED driver
ZXLD1374
Diodes Inc
Q1
60V MOSFET
2N7002A
Diodes Inc
D1
100V 3A Schottky
PDS3100-13
Diodes Inc
Z1
51V 410mW Zener
BZT52C51
Diodes Inc
L1
47µH 2.6A
744771147
Wurth Electronik
C1
100pF 50V
SMD 0805/0603
Generic
C3 C4
4.7µF 100V X7R
SMD1210
Generic
C2
1µF 50V X7R
SMD1206
Generic
R1 R2
300mΩ 1%
SMD1206
Generic
R3
120kΩ 1%
SMD 0805/0603
R4
36kΩ 1%
SMD 0805/0603
Generic
R5
2.7kΩ
SMD 0805/0603
Generic
Typical Performance
Efficiency vs Input Voltage
LED Current vs Input Voltage
100%
400
90%
350
80%
300
LED Current
Efficiency
70%
60%
50%
40%
30%
12 LED VF=37V
15 LED VF=47V
20%
250
200
150
100
12 LED VF=37V
15 LED VF=47V
50
10%
0
0%
16
18
20
22
24
26
28
30
Document number: DS35032 Rev. 3 - 2
18
20
22
24
26
28
30
Figure 51 Line Regulation
Figure 50 Efficiency
ZXLD1374
16
Input Voltage
Input Voltage
36 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Application Information (cont.)
350mA Buck-boost LED driver
In
this
application
example,
ZXLD1374
is
connected as a Buck-boost LED driver with
schematic and parts list shown below. The LED
driver is able to deliver 350mA of LED current into
4/5 high brightness LED with input voltage ranged
from 7V to 20V. In order to increase the driving
voltage level for the internal MOSFET during low
voltage input, bootstrap circuit formed by R6 D2
and C6 are used to supply higher voltage to the
VAUX pin.
Since the Buck-boost LED driver can handle an
input voltage range below and above the LED
voltage, this versatile input voltage range makes it
ideal for automotive lighting applications.
Figure 52 Application Circuit of 350mA Buck-Boost LED Driver
Bill of Material
Ref No.
U1
Q1
D1
D2
Z1
L1
C1
C3 C4 C5
C2 C6
R1 R2
R3
R4
R5
R6
Value
60V LED driver
60V MOSFET
100V 3A Schottky
100V 1A Schottky
47V 410mW Zener
47µH 2.6A
100pF 50V
4.7µF 50V X7R
1µF 50V X7R
300mΩ 1%
120kΩ 1%
36kΩ 1%
2.7kΩ
1kΩ
Part No.
ZXLD1374
2N7002A
PDS3100-13
B1100
BZT52C47
744771147
SMD 0805/0603
SMD1210
SMD1206
SMD1206
SMD 0805/0603
SMD 0805/0603
SMD 0805/0603
SMD 1206
Manufacturer
Diodes Inc
Diodes Inc
Diodes Inc
Diodes Inc
Diodes Inc
Wurth Electronik
Generic
Generic
Generic
Generic
Generic
Generic
Generic
Generic
Typical Performance
LED Current vs Input Voltage
Efficiency vs Input Voltage
90%
400
80%
350
70%
300
LED Current
Efficiency
100%
60%
50%
40%
30%
250
200
150
100
20%
4 LED VF=12.5V
5 LED VF=15.6V
10%
4 LED VF=12.5V
5 LED VF=15.6V
50
0
0%
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Document number: DS35032 Rev. 3 - 2
8
9
10
11
12
13
14
15
16
17
18
19
20
Figure 54 Line Regulation
Figure 53 Efficiency
ZXLD1374
7
Input Voltage
Input Voltage
37 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
Ordering Information
Part Number
Packaging
Part Marking
ZXLD1374EST20TC
TSSOP-20EP
ZXLD1374QESTTC
TSSOP-20EP
ZXLD
1374
YYWW
ZXLD
1374
YYWW
Reel
Quantity
Tape
Width
Reel Size
Qualification
2500
16mm
13”
AEC-Q100 Grade 1
2500
16mm
13”
Automotive Grade
Where YY stands for last 2 digits of year - 10, 11 and WW stands for week number
Package Outline Dimensions (All dimensions in mm.)
Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for latest version.
X
D
Y
E
1
E
TSSOP-20EP
Dim
Min
Max
Typ
A
1.20
A1
0.025 0.100
A2
0.80
1.05
0.90
b
0.19
0.30
c
0.09
0.20
D
6.40
6.60
6.50
E
6.20
6.60
6.40
E1
4.30
4.50
4.40
L
0.45
0.75
0.60
L1
1.0 REF
L2
0.65 BSC
X
4.191
Y
2.997
θ1
0°
8°
All Dimensions in mm
K
1R
NA
IM
P
D
I
e
e
n
a
l
5P
2e
.
0
g
u
a
G
A
2
A
e
n
a
l
P
g
n
i
t
a
e
S
L
L
I
A
T
E
D
1
L
1
A
b
θ1
Suggested Pad Layout
Please see AP02001 at http://www.diodes.com/datasheets/ap02001.pdf for the latest version.
X (20x)
C
Dimensions
Y1
Y2
C
X
X1
X2
Y
Y1
Y2
Y3
Y3
X1
Y (20x)
Value
(in mm)
0.650
0.420
4.490
6.270
1.780
3.290
4.160
7.720
X2
ZXLD1374
Document number: DS35032 Rev. 3 - 2
38 of 39
www.diodes.com
September 2012
© Diodes Incorporated
A Product Line of
Diodes Incorporated
ZXLD1374
IMPORTANT NOTICE
DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
(AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).
Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes
without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the
application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or
trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume
all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated
website, harmless against all damages.
Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and
hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or
indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.
Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings
noted herein may also be covered by one or more United States, international or foreign trademarks.
LIFE SUPPORT
Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express
written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:
A. Life support devices or systems are devices or systems which:
1. are intended to implant into the body, or
2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the
labeling can be reasonably expected to result in significant injury to the user.
B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the
failure of the life support device or to affect its safety or effectiveness.
Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any
use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related
information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its
representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems.
Copyright © 2012, Diodes Incorporated
www.diodes.com
ZXLD1374
Document number: DS35032 Rev. 3 - 2
39 of 39
www.diodes.com
September 2012
© Diodes Incorporated