ES2AW THRU ES2JW Surface Mount Superfast Recovery Rectifier Reverse Voltage – 50 to 600 V Forward Current – 2 A SOD-123FL FEATURES • Easy pick and place • For surface mounted applications • Low profile package • Built-in strain relief • Superfast recovery times for high efficiency 1.8± 0.1 0.2 Cathode Band Top View 1.2± 0.25 0.10-0.30 2.8 0.2 MECHANICAL DATA • Case: SOD-123FL • Terminals: Solderable per MIL-STD-750, Method 2026 • Approx. Weight:15mg 0.00048oz 0.6 0.25 3.7 Absolute Maximum Ratings and Characteristics 0.2 Dimensions in millimeters Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Symbols ES2AW ES2BW ES2CW ES2DW ES2EW ES2GW ES2JW Units Parameter Maximum Repetitive Peak Reverse Voltage V RRM 50 100 150 200 300 400 600 V Maximum RMS voltage V RMS 35 70 105 140 210 280 420 V Maximum DC Blocking Voltage V DC 50 100 150 200 300 400 600 V Maximum Average Forward Rectified Current at T L = 75 °C I F(AV) 2 A Peak Forward Surge Current 8.3 ms Single Half Sine Wave Superimposed on Rated Load (JEDEC Method) I FSM 50 A Maximum Forward Voltage at 2 A VF Maximum DC Reverse Current at Rated DC Blocking Voltage Ta = 25 °C Ta =125 °C 1.25 1 1.7 V IR 5 100 μA Typical Junction Capacitance at V R =4V, f=1MHz Cj 62 pF Maximum Reverse Recovery Time at I F =0.5A, I R =1A, I rr =0.25A t rr 35 ns RθJA 40 °C/W T j , T stg -55 ~ +150 °C Typical Thermal Resistance 1） Operating and Storage Temperature Range 1）P.C.B. mounted with 0.2x0.2”(5.0x5.0mm) copper pad areas 1 ES2AW THRU ES2JW Surface Mount Superfast Recovery Rectifier Reverse Voltage – 50 to 600 V Forward Current – 2 A Fig.1 Reverse Recovery Time Characteristic And Test Circuit Diagram 50 ohm Noninductive 10 ohm Noninductive t rr +0.5 D.U.T + PULSE GENERATOR Note 2 25Vdc approx 0 - -0.25 1 ohm OSCILLOSCOPE Note 1 NonInductive -1.0 Note：1.Rise Time = 7ns, max. Input Impedance = 1megohm,22pF. 2. Ries Time =10ns, max. Source Impedance = 50 ohms. 10ns/div Set time Base for 10ns/div Fig.3 Typical Reverse Characteristics 300 2.5 I R - Reverse Current ( μ A) Average Forward Current (A) Fig.2 Maximum Average Forward Current Rating 2.0 1.5 1.0 Single phase half wave resistive or inductive P.C.B mounted on 0.315×0. 315"(8.0×8. 0mm ) pad areas 0.5 100 T J =125°C 10 T J =75°C 1.0 T J =25°C 0.1 0.0 25 50 75 100 125 150 175 0 Lead Temperature (°C) Peak Forward Surage Current (A) Instaneous Forward Current (A) T J =25°C 1.0 0.1 ES2AW~ES2DW ES2GW ES2JW~ES2MW 0.001 0.5 1.0 1.5 60 80 100 Fig.5 Maximum Non-Repetitive Peak Forward Surage Current 10 0 40 % of PIV.VOLTS Fig.4 Typical Forward Characteristics 0.01 20 2.0 60 50 40 30 20 8.3 ms Single Half Sine Wave (JEDEC Method) 10 00 1 2.5 10 Number of Cycles Instaneous Forward Voltage (V) 2 100