MB85R4001A

FUJITSU SEMICONDUCTOR
DATA SHEET
DS501-00005-5v1-E
Memory FRAM
4 M Bit (512 K × 8)
MB85R4001A
■ DESCRIPTIONS
The MB85R4001A is an FRAM (Ferroelectric Random Access Memory) chip consisting of 524,288
words × 8 bits of nonvolatile memory cells fabricated using ferroelectric process and silicon gate CMOS
process technologies.
The MB85R4001A is able to retain data without using a back-up battery, as is needed for SRAM.
The memory cells used in the MB85R4001A can be used for 1010 read/write operations, which is a significant
improvement over the number of read and write operations supported by Flash memory and E2PROM.
The MB85R4001A uses a pseudo-SRAM interface.
■ FEATURES
: 524,288 words × 8 bits
: 1010 times / byte
: 10 years ( + 55 °C), 55 years ( + 35 °C)
: 3.0 V to 3.6 V
: Operating power supply current 15 mA (Typ)
Standby current 50 μA (Typ)
• Operation ambient temperature range : − 40 °C to + 85 °C
• Package
: 48-pin plastic TSOP (FPT-48P-M48)
RoHS compliant
•
•
•
•
•
Bit configuration
Read/write endurance
Data retention
Operating power supply voltage
Low power operation
Copyright 2011-2015 FUJITSU SEMICONDUCTOR LIMITED
2015.5
MB85R4001A
■ PIN ASSIGNMENTS
(TOP VIEW)
A11
A9
NC
A8
A13
WE
CE2
A15
A18
VDD
NC
NC
VSS
NC
NC
VDD
A17
A16
A14
A12
A7
A6
A5
A4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
OE
NC
VSS
A10
CE1
NC
I/O8
I/O7
I/O6
I/O5
I/O4
VDD
NC
I/O3
I/O2
I/O1
DNU
DNU
DNU
A0
A1
VSS
A2
A3
(FPT-48P-M48)
■ PIN DESCRIPTIONS
Pin Number
Pin Name
1, 2, 4, 5, 8, 9, 17 to 26, 28, 29,
45
A0 to A18
33 to 35, 38 to 42
I/O1 to I/O8
Data Input/Output pins
44
CE1
Chip Enable 1 Input pin
7
CE2
Chip Enable 2 Input pin
6
WE
Write Enable Input pin
48
OE
Output Enable Input pin
10, 16, 37
VDD
Supply Voltage pins
Connect all three pins to the power supply.
13, 27, 46
VSS
Ground pins
Connect all three pins to ground.
3, 11, 12, 14, 15, 36, 43, 47
NC
No Connect pins
Leave these pins open, or connect to VDD or
VSS.
30 to 32
DNU
Do Not Use pins
Make sure to connect these pins to ground.
2
Functional Description
Address Input pins
DS501-00005-5v1-E
MB85R4001A
■ BLOCK DIAGRAM
Address Latch
Row Decoder
A0
FRAM Array
524,288 × 8
A18
Column Decoder
S/A
intWE
intOE
I/O1 to I/O8
I/O8
CE2
CE1
WE
OE
I/O1
■ FUNCTIONAL TRUTH TABLE
Operation Mode
Standby Precharge
CE1
CE2
WE
OE
H
X
X
X
X
L
X
X
X
X
H
H
H
L
I/O1 to I/O8
Supply Current
Hi-Z
Standby
(ISB)
H
Read
L
Read
(Pseudo-SRAM, OE control*1)
L
Data Output
H
H
Operation
(IDD)
H
Write
L
H
L
Write
(Pseudo-SRAM, WE control*2)
L
Data Input
H
Note: L = VIL, H = VIH, X can be either VIL, VIH,
or
: Latch address and latch data at falling edge,
H
, Hi-Z = High Impedance
: Latch address and latch data at rising edge
*1 : OE control of the Pseudo-SRAM means the valid address at the falling edge of OE to read.
*2 : WE control of the Pseudo-SRAM means the valid address and data at the falling edge of WE to write.
DS501-00005-5v1-E
3
MB85R4001A
■ ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Rating
Min
Max
Unit
Power Supply Voltage*
VDD
− 0.5
+ 4.0
V
Input Pin Voltage*
VIN
− 0.5
VDD + 0.5 ( ≤ 4.0)
V
VOUT
− 0.5
VDD + 0.5 ( ≤ 4.0)
V
TA
− 40
+ 85
°C
TSTG
− 55
+ 125
°C
Output Pin Voltage*
Operation Ambient Temperature
Storage Temperature
* : All voltages are referenced to VSS (ground 0 V).
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
■ RECOMMENDED OPERATING CONDITIONS
Parameter
Symbol
Value
Min
Typ
Max
Unit
Power Supply Voltage*1
VDD
3.0
3.3
3.6
V
Operation Ambient Temperature*2
TA
− 40
⎯
+ 85
°C
*1 : All voltages are referenced to VSS (ground 0 V).
*2 : Ambient temperature when only this device is working. Please consider it to be the almost same as the
package surface temperature.
WARNING: The recommended operating conditions are required in order to ensure the normal operation of
the semiconductor device. All of the device's electrical characteristics are warranted when the
device is operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges.
Operation outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented
on the data sheet. Users considering application outside the listed conditions are advised to contact
their representatives beforehand.
4
DS501-00005-5v1-E
MB85R4001A
■ ELECTRICAL CHARACTERISTICS
1. DC Characteristics
Parameter
Symbol
Condition
(within recommended operating conditions)
Value
Unit
Min
Typ
Max
Input Leakage Current*1
|ILI|
VIN = 0 V to VDD
⎯
⎯
10
μA
Output Leakage Current
|ILO|
VOUT = 0 V to VDD,
CE1 = VIH or OE = VIH
⎯
⎯
10
μA
Operating Power Supply
Current*2
IDD
CE1 = 0.2 V, CE2 = VDD−0.2 V,
Iout = 0 mA
⎯
15
20
mA
⎯
50
150
μA
CE1 ≥ VDD−0.2 V
Standby Current*3
ISB
CE2 ≤ 0.2 V
OE ≥ VDD−0.2 V, WE ≥ VDD−0.2 V
High Level Input Voltage
VIH
VDD = 3.0 V to 3.6 V
VDD × 0.8
⎯
VDD + 0.5(
≤ 4.0)
V
Low Level Input Voltage
VIL
VDD = 3.0 V to 3.6 V
− 0.5
⎯
+ 0.6
V
High Level Output Voltage
VOH
IOH = −1.0 mA
VDD × 0.8
⎯
⎯
V
Low Level Output Voltage
VOL
IOL = 2.0 mA
⎯
⎯
0.4
V
*1 : This also applies to DNU pins.
*2 : During the measurement of IDD, the Address and Data In were taken to only change once per active cycle.
Iout: output current
*3 : All pins other than setting pins shall be input at the CMOS level voltages such as H ≥ VDD − 0.2 V, L ≤ 0.2 V.
DS501-00005-5v1-E
5
MB85R4001A
2. AC Characteristics
• AC Test Conditions
Power Supply Voltage
Operation Ambient Temperature
Input Voltage Amplitude
Input Rising Time
Input Falling Time
Input Evaluation Level
Output Evaluation Level
Output Load Capacitance
: 3.0 V to 3.6 V
: −40 °C to +85 °C
: 0.3 V to 2.7 V
: 5 ns
: 5 ns
: 2.0 V / 0.8 V
: 2.0 V / 0.8 V
: 50 pF
(1) Read Cycle
Parameter
Symbol
Value
Min
Max
Unit
Read Cycle Time
tRC
150
⎯
ns
CE1 Active Time
tCA1
120
⎯
ns
CE2 Active Time
tCA2
120
⎯
ns
OE Active Time
tRP
120
⎯
ns
Precharge Time
tPC
20
⎯
ns
Address Setup Time
tAS
0
⎯
ns
Address Hold Time
tAH
50
⎯
ns
OE Setup Time
tES
0
⎯
ns
Output Hold Time
tOH
0
⎯
ns
Output Set Time
tLZ
30
⎯
ns
CE1 Access Time
tCE1
⎯
120
ns
CE2 Access Time
tCE2
⎯
120
ns
OE Access Time
tOE
⎯
120
ns
Output Floating Time
tOHZ
⎯
20
ns
(2) Write Cycle
Parameter
Symbol
Value
Min
Max
Unit
Write Cycle Time
tWC
150
⎯
ns
CE1 Active Time
tCA1
120
⎯
ns
CE2 Active Time
tCA2
120
⎯
ns
Precharge Time
tPC
20
⎯
ns
Address Setup Time
tAS
0
⎯
ns
Address Hold Time
tAH
50
⎯
ns
Write Pulse Width
tWP
120
⎯
ns
Data Setup Time
tDS
0
⎯
ns
Data Hold Time
tDH
50
⎯
ns
Write Setup Time
tWS
0
⎯
ns
6
DS501-00005-5v1-E
MB85R4001A
3. Pin Capacitance
Parameter
Input Capacitance
Symbol
CIN
Output Capacitance
COUT
DNU Pin Input Capacitance
CDNU
DS501-00005-5v1-E
Condition
VDD = VIN = VOUT = 0 V,
f = 1 MHz, TA = +25 °C
Value
Unit
Min
Typ
Max
⎯
⎯
10
pF
⎯
⎯
10
pF
⎯
⎯
10
pF
7
MB85R4001A
■ TIMING DIAGRAMS
1. Read Cycle Timing (CE1 Control)
tRC
tCA1
tPC
CE1
CE2
tAS
A0 to A18
tAH
Valid
H or L
tES
tRP
OE
tCE1
tOH
tLZ
I/O1 to I/O8
tOHZ
Hi-Z
Valid
Invalid
Invalid
:H or L
2. Read Cycle Timing (CE2 Control)
CE1
tRC
tPC
tCA2
CE2
tAS
A0 to A18
tAH
Valid
H or L
tES
tRP
OE
tCE2
tOH
tLZ
I/O1 to I/O8
tOHZ
Hi-Z
Valid
Invalid
Invalid
:H or L
8
DS501-00005-5v1-E
MB85R4001A
3. Read Cycle Timing (OE Control)
CE1
CE2
tAS
A0 to A18
tAH
Valid
H or L
tRC
tPC
tRP
OE
tOE
tOHZ
tOH
tLZ
I/O1 to I/O8
Hi-Z
Valid
Invalid
Invalid
:H or L
4. Write Cycle Timing (CE1 Control)
tWC
tCA1
tPC
CE1
CE2
tAS
A0 to A18
tAH
Valid
H or L
tWS
tWP
WE
tDS
tDH
Hi-Z
Valid
Data In
H or L
:H or L
DS501-00005-5v1-E
9
MB85R4001A
5. Write Cycle Timing (CE2 Control)
CE1
tWC
tPC
tCA2
CE2
tAS
A0 to A18
tAH
Valid
H or L
tWS
tWP
WE
tDS
tDH
Hi-Z
Valid
Data In
H or L
:H or L
6. Write Cycle Timing (WE Control)
CE1
CE2
tAS
A0 to A18
tAH
Valid
H or L
tWC
tWP
tPC
WE
tDS
tDH
Hi-Z
Data In
Valid
H or L
:H or L
10
DS501-00005-5v1-E
MB85R4001A
■ POWER ON/OFF SEQUENCE
tPD
tR
tPU
VDD
VDD
CE2
CE2
3.0 V
3.0 V
VIH (Min)
VIH (Min)
1.0 V
1.0 V
VIL (Max)
VIL (Max)
CE2 ≤ 0.2 V
0V
0V
CE1 > VDD × 0.8*
CE1 > VDD × 0.8*
CE1 : Don't Care
CE1
CE1
* : CE1 (Max) < VDD + 0.5 V
Parameter
Value
Symbol
Min
Typ
Max
Unit
CE1 level hold time for Power OFF
tPD
85
⎯
⎯
ns
CE1 level hold time for Power ON
tPU
85
⎯
⎯
ns
Power supply rising time
tR
0.05
⎯
200
ms
If the device does not operate within the specified conditions of read cycle, write cycle or power on/off
sequence, memory data can not be guaranteed.
In case the power is turned on or off, use the power supply reset IC and fix the CE2 to low level, to prevent
unexpected writing. Use either of CE1 or CE2, or both to disable control of the device.
■ FRAM CHARACTERISTICS
Item
Min
Max
Read/Write Endurance*1
1010
⎯
10
⎯
55
⎯
Data Retention*2
Unit
Parameter
Times/byte Operation Ambient Temperature TA = + 85 °C
Years
Operation Ambient Temperature TA = + 55 °C
Operation Ambient Temperature TA = + 35 °C
*1 : Total number of reading and writing defines the minimum value of endurance, as an FRAM memory operates
with destructive readout mechanism.
*2 : Minimum values define retention time of the first reading/writing data right after shipment, and these values
are calculated by qualification results.
■ NOTES ON USE
We recommend programming of the device after reflow. Data written before reflow cannot be guaranteed.
DS501-00005-5v1-E
11
MB85R4001A
■ ESD AND LATCH-UP
Test
DUT
Value
ESD HBM (Human Body Model)
JESD22-A114 compliant
≥ |2000 V|
ESD MM (Machine Model)
JESD22-A115 compliant
≥ |200 V|
ESD CDM (Charged Device Model)
JESD22-C101 compliant
⎯
Latch-Up (I-test)
JESD78 compliant
MB85R4001ANC-GE1
Latch-Up (Vsupply overvoltage test)
JESD78 compliant
⎯
⎯
Latch-Up (Current Method)
Proprietary method
≥ |300 mA|
Latch-Up (C-V Method)
Proprietary method
⎯
• Current method of Latch-Up Resistance Test
Protection Resistor
A
Test terminal
IIN
VIN
VDD
+
DUT
-
VSS
VDD
(Max.Rating)
V
Reference
terminal
Note : The voltage VIN is increased gradually and the current IIN of 300 mA at maximum shall flow.
Confirm the latch up does not occur under IIN = ± 300 mA.
In case the specific requirement is specified for I/O and IIN cannot be 300 mA, the voltage shall be
increased to the level that meets the specific requirement.
12
DS501-00005-5v1-E
MB85R4001A
• C-V method of Latch-Up Resistance Test
Protection Resistor
A
1
Test
2 terminal
SW
+
VIN
V
-
C
200pF
VDD
DUT
VDD
(Max.Rating)
VSS
Reference
terminal
Note : Charge voltage alternately switching 1 and 2 approximately 2 sec interval. This switching process is
considered as one cycle.
Repeat this process 5 times. However, if the latch-up condition occurs before completing 5 times, this
test must be stopped immediately.
■ REFLOW CONDITIONS AND FLOOR LIFE
[ JEDEC MSL ] : Moisture Sensitivity Level 3 (ISP/JEDEC J-STD-020D)
■ CURRENT STATUS ON CONTAINED RESTRICTED SUBSTANCES
This product complies with the regulations of REACH Regulations, EU RoHS Directive and China RoHS.
DS501-00005-5v1-E
13
MB85R4001A
■ ORDERING INFORMATION
Part Number
MB85R4001ANC-GE1
Package
Shipping form
Minimum shipping
quantity
48-pin plastic TSOP
(FPT-48P-M48)
Tray
⎯*
*: Please contact our sales office about minimum shipping quantity.
14
DS501-00005-5v1-E
MB85R4001A
■ PACKAGE DIMENSIONS
48-pin plastic TSOP
Lead pitch
0.50 mm
Package width ×
package length
12.00 mm × 12.40 mm
Lead shape
Gullwing
Sealing method
Plastic mold
Mounting height
1.20 mm MAX
Weight
0.36 g
(FPT-48P-M48)
Note 1) # : Resin protrusion. (Each side : +0.15 (.006) Max).
Note 2) * : These dimensions do not include resin protrusion.
Note 3) Pins width and pins thickness include plating thickness.
Note 4) Pins width do not include tie bar cutting remainder.
48-pin plastic TSOP
(FPT-48P-M48)
0.10±0.05 (.004±.002)
(STAND OFF)
1
48
0.50(.020)
INDEX
#12.00±0.10
(.472±.004)
+0.05
0.22 –0.04
(.009 +.002
–.002 )
24
0.10(.004)
M
25
1.13±0.07 (.044±.003)
(MOUNTING HEIGHT)
Details of A part
14.00±0.20(.551±.008)
*12.40±0.10(.488±.004)
0.25(.010)
+0.05
0.145 –0.03
(.006 +.002
–.001 )
C
0.08(.003)
2010 FUJITSU SEMICONDUCTOR LIMITED F48048Sc-1-1
DS501-00005-5v1-E
A
0.60±0.15
(.024±.006)
0~8
Dimensions in mm (inches).
Note: The values in parentheses are reference values.
15
MB85R4001A
■ MARKING
[MB85R4001ANC-GE1]
JAPAN
MB85R4001A
1150 E00
E1
[FPT-48P-M48]
16
DS501-00005-5v1-E
MB85R4001A
■ SHIPPING FORM
1. Tray
1.1 Tray Dimensions
TSOP48, 56 (I)
Maximum storage capacity
PKG code
pcs/tray
pcs/inner box
pcs/outer box
128
1280
5120
322.6
315
15 × 19.0 = 285
15
15
8-NO HOLES
7.62
1.27
7 × 14.9 = 104.3
135.9
15.8
FPT-48P-M48
25.4
25.4
R4.7
255.3
1
13.564
12.2
10
8
1.27
1
1 1
SEC.A-A
1
10
19
15.8
1 1
8
0.9
1.27
1
15
0.9
1.27
1.27
7.62
7.62
2
1.27
15.564
14.2
11.8
10
2
34.3
C
5
B
A
0.76
C3
2.54
A
15.8
B
14.9
SEC.B-B
2002-2010 FUJITSU SEMICONDUCTOR LIMITED TSOP (1) 12 × 14 : JHB-TS1-1214-1-D-3
(Dimensions in mm)
Material : Conductive polyphenyleneether
Heat proof temperature : 125 °C MAX
Weight : 133 g
DS501-00005-5v1-E
17
MB85R4001A
1.2 IEC (JEDEC) TRAY Dry Pack Packing Specifications
Product (IC)
Tray
Index mark
IC
Chamfered corner
Tray
*5
Humidity
indicator
Desiccant *5
Label I *1*4*5
*5
Dry pack
↓
Inner box
Heat seal
Binding band
or tape
Aluminum laminated bag *5
Filled tray + one empty tray
Cushioning material *5
Inner box *5
*5
Binding band
or tape
Label I *1*4*5
Cushioning material *5
Outer box
Outer box *2*3*5
Use adhesive tapes. *5
Label II-A *4*5
Label II-B *4*5
*1: For a product of witch part number is suffixed with "E1", a " G
bag and the inner boxes.
Pb
" marks is display to the moisture barrier
*2: The size of the outer box may be changed depending on the quantity of inner boxes.
*3: The space in the outer box will be filled with empty inner boxes, or cushions, etc.
*4: Please refer to an attached sheet about the indication label.
*5: The packing materials except tray may differ slightly from the color and dimensions depend on country of
manufacture.
Note: The packing specifications may not be applied when the product is delivered via a distributor.
18
DS501-00005-5v1-E
MB85R4001A
1.3 Product label indicators
Label I: Label on Inner box/Moisture Barrier Bag/ (It sticks it on the reel for the emboss taping)
[C-3 Label (50mm x 100mm) Supplemental Label (20mm x 100mm)]
XXXXXXXXXXXXXX
(Customer part number or FJ part number)
C-3 Label
(LEAD FREE mark)
(3N)1 XXXXXXXXXXXXXX XXX
(Part number and quantity)
QC PASS
(3N)2 XXXXXXXXXX XXXXXX
(FJ control number)
XXX pcs
XXXXXXXXXXXXXX
(Quantity)
(Customer part number or FJ part number)
(Customer part number or FJ part number
bar code)
XXXX/XX/XX (Packed years/month/day) ASSEMBLED IN xxxx
XXXXXXXXXXXXXX (Customer part number or FJ part number)
(FJ control number bar code)
XX/XX
XXXX-XXX XXX
(Package count)
XXXX-XXX XXX
XXXXXXXXXX (FJ control number ) (Lot Number and quantity)
XXXXXXXXXXXXXX (Comment)
Perforated line
Supplemental Label
Label II-A: Label on Outer box [D Label] (100mm x 100mm)
D Label
XXXXXXXXXXXXX (Customer Name)
(CUST.)
XXXXXXXXX (Delivery Address)
(DELIVERY POINT)
XXXXXXXXXXXXXX
(TRANS.NO.) (FJ control number)
XXXXXXXXXXXXXX
(PART NO.)
(Customer part number or
FJ part number)
XXX (FJ control number)
XXX (FJ control number)
XXX (FJ control number)
XXXXXXXXXXXXXX
(Part number)
(PART NAME) XXXXXXXXXXXXXX (Part number)
XXX/XXX
(Q’TY/TOTAL Q’TY)
(CUSTOMER'S
REMARKS)
XXXXXXXXXXXXXXXXXXXX
(3N)3 XXXXXXXXXXXXXX XXX
XX
(UNIT)
(PACKAGE COUNT)
XXX/XXX
(FJ control number + Product quantity)
(FJ control number + Product quantity
bar code)
(Part number + Product quantity)
(3N)4 XXXXXXXXXXXXXX XXX
(Part number + Product quantity bar code)
(3N)5 XXXXXXXXXX
(FJ control number)
(FJ control number bar code)
Label II-B: Outer boxes product indicate
XXXXXXXXXXXXXX
(Lot Number)
XXXX-XXX
XXXX-XXX
(Part number)
(Count)
X
X
(Quantity)
XXX
XXX
XXX
Note: Depending on shipment state, "Label II-A" and "Label II-B" on the external boxes might not be printed.
DS501-00005-5v1-E
19
MB85R4001A
1.4 Dimensions for Containers
(1) Dimensions for inner box
H
W
L
L
W
H
165
360
75
(Dimensions in mm)
(2) Dimensions for outer box
H
W
L
L
W
H
355
385
195
(Dimensions in mm)
20
DS501-00005-5v1-E
MB85R4001A
■ MAJOR CHANGES IN THIS EDITION
A change on a page is indicated by a vertical line drawn on the left side of that page.
Page
Section
Change Results
1
■ DESCRIPTIONS
Deleted the “that is compatible with conventional asynchronous SRAM”.
4
■ RECOMMENDED OPERATING
CONDITIONS
Added note on the Operation Ambient Temperature.
Moved the “High Level Input Voltage” and “Low Level
Input Voltage” to DC Characteristics.
1. DC Characteristics
Moved the “High Level Input Voltage” and “Low Level
Input Voltage” from RECOMMENDED OPERATING
CONDITIONS.
5
13
■ CURRENT STATUS ON CONTAINED Deleted the URL info.
RESTRICTED SUBSTANCES
DS501-00005-5v1-E
21
MB85R4001A
MEMO
22
DS501-00005-5v1-E
MB85R4001A
MEMO
DS501-00005-5v1-E
23
MB85R4001A
FUJITSU SEMICONDUCTOR LIMITED
Shin-Yokohama Chuo Building, 2-100-45 Shin-Yokohama,
Kohoku-ku, Yokohama, Kanagawa 222-0033, Japan
http://jp.fujitsu.com/fsl/en/
All Rights Reserved.
FUJITSU SEMICONDUCTOR LIMITED, its subsidiaries and affiliates (collectively, "FUJITSU SEMICONDUCTOR") reserves
the right to make changes to the information contained in this document without notice. Please contact your FUJITSU
SEMICONDUCTOR sales representatives before order of FUJITSU SEMICONDUCTOR device.
Information contained in this document, such as descriptions of function and application circuit examples is presented solely for
reference to examples of operations and uses of FUJITSU SEMICONDUCTOR device. FUJITSU SEMICONDUCTOR disclaims
any and all warranties of any kind, whether express or implied, related to such information, including, without limitation, quality,
accuracy, performance, proper operation of the device or non-infringement. If you develop equipment or product incorporating the
FUJITSU SEMICONDUCTOR device based on such information, you must assume any responsibility or liability arising out of or
in connection with such information or any use thereof. FUJITSU SEMICONDUCTOR assumes no responsibility or liability for any
damages whatsoever arising out of or in connection with such information or any use thereof.
Nothing contained in this document shall be construed as granting or conferring any right under any patents, copyrights, or any other
intellectual property rights of FUJITSU SEMICONDUCTOR or any third party by license or otherwise, express or implied.
FUJITSU SEMICONDUCTOR assumes no responsibility or liability for any infringement of any intellectual property rights or other
rights of third parties resulting from or in connection with the information contained herein or use thereof.
The products described in this document are designed, developed and manufactured as contemplated for general use including
without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and
manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high levels of safety is secured,
could lead directly to death, personal injury, severe physical damage or other loss (including, without limitation, use in nuclear
facility, aircraft flight control system, air traffic control system, mass transport control system, medical life support system and
military application), or (2) for use requiring extremely high level of reliability (including, without limitation, submersible repeater
and artificial satellite). FUJITSU SEMICONDUCTOR shall not be liable for you and/or any third party for any claims or damages
arising out of or in connection with above-mentioned uses of the products.
Any semiconductor devices fail or malfunction with some probability. You are responsible for providing adequate designs and
safeguards against injury, damage or loss from such failures or malfunctions, by incorporating safety design measures into your
facility, equipments and products such as redundancy, fire protection, and prevention of overcurrent levels and other abnormal
operating conditions.
The products and technical information described in this document are subject to the Foreign Exchange and Foreign Trade Control
Law of Japan, and may be subject to export or import laws or regulations in U.S. or other countries. You are responsible for ensuring
compliance with such laws and regulations relating to export or re-export of the products and technical information described herein.
All company names, brand names and trademarks herein are property of their respective owners.
Edited: System Memory Business Division