AK4495(S)

[AK4495S/95]
AK4495S/95
Quality-oriented Premium 32-Bit 2ch DAC
1. General Description
The AK4495S/95 is a 32-bit DAC, which corresponds to high-performance, high sound quality digital audio
systems such as DVD-Audio and BD. An internal circuit includes newly developed 32-bit digital filters for
better sound quality, achieving low distortion characteristics and wide dynamic range. The AK4495S/95 has
full differential SCF outputs, removing the need for AC coupling capacitors and increasing performance for
systems with excessive clock jitter. The AK4495S/95 accepts up to 768kHz PCM data and 5.6MHz DSD data,
ideal for a wide range of applications including Network Audio and SACD.
2. Features
 128x Over sampling
 Sampling Rate: 30kHz  768kHz
 32-bit 8x Digital Filter
- Ripple: 0.005dB, Attenuation: 100dB
- Short Delay Sharp Roll-off, GD=6.25/fs
- Short Delay Slow Roll-off, GD=5.3/fs
- Sharp Roll-off
- Slow Roll-off
- Super Slow Roll-off
 High Tolerance to Clock Jitter
 Low Distortion Differential Output
 2.8MHz, 5.6MHz DSD Input Support
 Digital De-emphasis for 32, 44.1, 48kHz sampling
 Soft Mute
 Digital Attenuator (255 levels and 0.5dB step)
 Mono Mode
 External Digital Filter Mode
 THD+N: -101dB, -105dB (Analog Block Power Supply 7V)
 DR, S/N: 120dB, 123dB (Mono mode: 126dB, Analog Block Power Supply 7V)
 I/F Format: 24/32bit MSB justified, 16/20/24/32bit LSB justified, I2S, DSD
 Master Clock:
30kHz ~ 32kHz: 1152fs
30kHz ~ 54kHz: 512fs or 768fs
30kHz ~ 108kHz: 256fs or 384fs
108kHz ~ 216kHz: 128fs or 192fs
~ 384kHz: 64fs or 128fs
~ 768kHz: 64fs
 Power Supply: DVDD=AVDD=3.0 3.6V, VDD1/2=4.75  7.2V
 Digital Input Level: CMOS
 Package: 44-pin LQFP
MS1560-E-02
2014/04
-1-
[AK4495S/95]
3. Table of Contents
1. General Description ....................................................................................................................................... 1
2. Features.......................................................................................................................................................... 1
3. Table of Contents .......................................................................................................................................... 2
4. Block Diagram and Functions ....................................................................................................................... 4
5. Pin Configuration and Functions ................................................................................................................... 5
■ Ordering Guide ......................................................................................................................................... 5
■ Pin Configuration ..................................................................................................................................... 5
■ Functions .................................................................................................................................................. 6
■ Handling of Unused Pin ........................................................................................................................... 8
6. Absolute Maximum Ratings .......................................................................................................................... 9
7. Recommended Operation Conditions ............................................................................................................ 9
8. Electrical Characteristics ............................................................................................................................. 10
■ Handling of Unused Pin ......................................................................................................................... 10
■ Sharp Roll-Off Filter Characteristics (fs = 44.1kHz) ............................................................................. 11
■ Sharp Roll-Off Filter Characteristics (fs = 96kHz) ................................................................................ 11
■ Sharp Roll-Off Filter Characteristics (fs = 192kHz) .............................................................................. 11
■ Short Delay Sharp Roll-Off Filter Characteristics (fs = 44.1kHz) ......................................................... 13
■ Short Delay Sharp Roll-Off Filter Characteristics (fs = 96kHz) ............................................................ 13
■ Short Delay Sharp Roll-Off Filter Characteristics (fs = 192kHz) .......................................................... 13
■ Slow Roll-Off Filter Characteristics (fs = 44.1kHz) .............................................................................. 15
■ Slow Roll-Off Filter Characteristics (fs = 96kHz) ................................................................................. 15
■ Slow Roll-Off Filter Characteristics (fs = 192kHz) ............................................................................... 15
■ Short Delay Slow Roll-Off Filter Characteristics (fs = 44.1kHz) .......................................................... 17
■ Short Delay Slow Roll-Off Filter Characteristics (fs = 96kHz) ............................................................. 17
■ Short Delay Slow Roll-Off Filter Characteristics (fs = 192kHz) ........................................................... 17
■ DC Characteristics .................................................................................................................................. 19
■ Switching Characteristics ....................................................................................................................... 20
■ Timing Diagram ..................................................................................................................................... 22
9. Functional Descriptions ............................................................................................................................... 26
■ D/A Conversion Mode ........................................................................................................................... 26
■ System Clock .......................................................................................................................................... 26
■ Audio Interface Format .......................................................................................................................... 32
■ D/A Conversion Mode Switching Timing.............................................................................................. 36
■ De-emphasis Filter.................................................................................................................................. 36
■ Output Volume (PCM, DSD) ................................................................................................................. 36
■ Zero Detection (PCM, DSD) .................................................................................................................. 37
■ Mono Output (PCM, DSD, EX DF I/F) ................................................................................................. 37
■ Sound Quality Control (PCM, DSD, Ex DF I/F).................................................................................... 37
■ Soft Mute Operation (PCM, DSD) ......................................................................................................... 38
■ System Reset .......................................................................................................................................... 38
■ Power ON/OFF timing ........................................................................................................................... 39
■ Reset Function ........................................................................................................................................ 40
■ Synchronize Function ............................................................................................................................. 42
■ Register Control Interface ...................................................................................................................... 44
■ Register Map .......................................................................................................................................... 49
■ Register Definitions ................................................................................................................................ 49
10. Recommended External Circuits ............................................................................................................... 55
11. Package ...................................................................................................................................................... 59
MS1560-E-02
2014/04
-2-
[AK4495S/95]
■ Outline Dimensions (AK4495S) ............................................................................................................ 59
■ Material & Lead finish ........................................................................................................................... 59
■ Outline Dimensions (AK4495) ............................................................................................................... 60
■ Material & Lead finish ........................................................................................................................... 60
■ Marking (AK4495S) ............................................................................................................................... 61
■ Marking (AK4495) ................................................................................................................................. 61
12. Revision History ........................................................................................................................................ 62
IMPORTANT NOTICE .................................................................................................................................. 63
MS1560-E-02
2014/04
-3-
[AK4495S/95]
4. Block Diagram and Functions
DVDD
BICK/DCLK/BCK
LRCK/DSDR/DINL
DVSS
PDN
AVDD
AVSS
VSSL
VDDL
PCM
Data
Interface
8X
Interpolator
SCF
AOUTLP
AOUTLN
SDATA/DSDL/DINR
DSD
Data
Interface
DATT
Soft Mute
Bias
Vref

Modulator
External
DF
Interface
SCF
VCML
VREFHL
VREFLL
VREFLR
VREFLL
VCMR
AOUTRP
AOUTRN
WCK/SSLOW
DEM0
DEM1
Control
Register
Clock
Divider
CSN/SMUTE
CCLK/SCL/SD
VDDR
VSSR
CDTI/SDA/SLOW
ACKS/CAD1 CAD0/DIF2 PSN DZFL/DIF0 I2C DZFR/DIF1
1
MCLK
Block Diagram
MS1560-E-02
2014/04
-4-
[AK4495S/95]
5. Pin Configuration and Functions
■ Ordering Guide
40  +85C
44-pin LQFP (0.8mm pitch)
40  +85C
44-pin LQFP (0.8mm pitch), Special Sound Quality Package
Evaluation Board for AK4495
Evaluation Board for AK4495S
AK4495EQ
AK4495SEQ
AKD4495
AKD4495S
AOUTLN
VDDL
VDDL
VSSL
VSSL
NC
VSSR
VSSR
VDDR
VDDR
AOUTRN
33
32
31
30
29
28
27
26
25
24
23
■ Pin Configuration
AOUTLP
34
22
AOUTRP
VCOML
35
21
VCOMR
VREFLL
36
20
VREFLR
19
VREFLR
18
VREFHR
17
VREFHR
16
ACKS/CAD1
OUTRP
VREFLL
37
VREFHL
38
VREFHL
39
AVDD
40
AVSS
1
MCLK
DVSS
41
DVDD
AK4495S/95
Top View
9
SLOW/CDTI/SDA
DIF0/DZFL
11
8
SD/CCLK/SCL
10
7
DIF2/CAD0
6
SMUTE/CSN
MS1560-E-02
DIF1/DZFR
5
WCK/SSLOW
4
PSN
LRCK/DSDR/DINR
12
3
44
2
I2C
SDATA/DSDL/DINL
13
1
DEM0
43
PDN
DEM1
14
BICK/DCLK/BCK
15
42
2014/04
-5-
[AK4495S/95]
■ Functions
No
Pin Name
.
1
I/O
PDN
I
BICK
DCLK
BCK
SDATA
DSDL
DINL
LRCK
DSDR
DINR
SSLOW
WCK
I
I
I
I
I
I
I
I
I
I
I
SMUTE
I
CSN
SD
I
I
CCLK
I
SCL
I
SLOW
I
CDTI
I
SDA
I/O
DIF0
DZFL
I
O
DIF1
DZFR
DIF2
CAD0
I
O
I
I
12
PSN
I
13
I2C
I
2
3
4
5
6
7
8
9
10
11
Function
Power-Down Mode Pin
When at “L”, the AK4495S/95 is in power-down mode and is held in reset.
The AK4495S/95 must always be reset upon power-up.
Audio Serial Data Clock Pin in PCM Mode
DSD Clock Pin in DSD Mode
Audio Serial Data Clock Pin
Audio Serial Data Input Pin in PCM Mode
DSD Lch Data Input Pin in DSD Mode
Lch Audio Serial Data Input Pin
L/R Clock Pin in PCM Mode
DSD Rch Data Input Pin in DSD Mode in Serial Control Mode
Rch Audio Serial Data Input Pin in Serial Control Mode
Digital filter setting in Parallel Control Mode
Word Clock input pin in Serial Control Mode
Soft Mute Pin in Parallel Control Mode
When this pin is changed to “H”, soft mute cycle is initiated.
When returning “L”, the output mute releases.
Chip Select Pin in Serial Control Mode in Serial Control Mode, I2C=“L”
Digital filter setting in Parallel Control Mode
Control Data Clock Pin in Serial Control Mode in Serial Control Mode,
I2C=“L”
Control Data Clock Pin in Serial Control Mode in Serial Control Mode,
I2C=“H”
Digital filter setting in Parallel Control Mode
Control Data Input Pin in Serial Control Mode in Serial Control Mode,
I2C=“L”
Control Data Clock Pin in Serial Control Mode in Serial Control Mode,
I2C=“H”
Digital Input Format 0 Pin in PCM Mode
Lch Zero Input Detect Pin in Serial Control Mode
Digital Input Format 1 Pin in PCM Mode
Rch Zero Input Detect Pin in Serial Control Mode
Digital Input Format 2 Pin in PCM Mode
Chip Address 0 Pin in Serial Control Mode
(Internal pull-down pin)
Parallel or Serial Select Pin
(Internal pull-up pin)
“L”: Serial Control Mode, “H”: Parallel Control Mode
I2C mode select pin in Serial mode (Internal pull-down pin)
14 DEM0
I
De-emphasis Enable 0 Pin in Parallel Control Mode (Internal pull-up pin)
Note: All input pins except internal pull-up/down pins must not be left floating.
MS1560-E-02
2014/04
-6-
[AK4495S/95]
15
DEM1
ACKS
CAD1
I
I
I
De-emphasis Enable 1 Pin in Parallel Control Mode (Internal pull-down pin)
Master Clock Auto Setting Mode Pin in Parallel Mode (Internal pull-down pin)
Chip Address 1 Pin in Serial Control Mode
17
VREFHR
I
Rch High Level Voltage Reference Input Pin
18
19
20
VREFHR
VREFLR
VREFLR
I
I
I
16
Rch High Level Voltage Reference Input Pin
Rch Low Level Voltage Reference Input Pin
Rch Low Level Voltage Reference Input Pin
Right channel Common Voltage Pin,
21 VCOMR
Normally connected to VREFLL with a 10uF electrolytic cap.
22 AOUTRP
O Rch Positive Analog Output Pin
23 AOUTRN
O Rch Negative Analog Output Pin
24 VDDR
Rch Analog Power Supply Pin, 4.75  7.2V
25 VDDR
Rch Analog Power Supply Pin, 4.75  7.2V
26 VSSR
Ground Pin
27 VSSR
Ground Pin
No internal bonding.
28 NC
Connect to GND.
29 VSSL
Ground Pin
30 VSSL
Ground Pin
31 VDDL
Lch Analog Power Supply Pin, 4.75  7.2V
32 VDDL
Lch Analog Power Supply Pin, 4.75  7.2V
33 AOUTLN
O Lch Negative Analog Output Pin
34 AOUTLP
O Lch Positive Analog Output Pin
Left channel Common Voltage Pin,
35 VCOML
Normally connected to VREFLR with a 10uF electrolytic cap.
36 VREFLL
I
Lch Low Level Voltage Reference Input Pin
37 VREFLL
I
Lch Low Level Voltage Reference Input Pin
38 VREFHL
I
Lch High Level Voltage Reference Input Pin
39 VREFHL
I
Lch High Level Voltage Reference Input Pin
40 AVDD
Analog Power Supply Pin, 3.0  3.6V
41 AVSS
Ground Pin
42 MCLK
I
Master Clock Input Pin
43 DVSS
Ground Pin
44 DVDD
Digital Power Supply Pin, 3.0  3.6V
Note: All input pins except internal pull-up/down pins must not be left floating.
MS1560-E-02
2014/04
-7-
[AK4495S/95]
■ Handling of Unused Pin
The unused I/O pins should be processed appropriately as below.
(1) Parallel Mode (PCM Mode only)
Classification
Analog
Digital
Pin Name
AOUTLP, AOUTLN
AOUTRP, AOUTRN
Setting
These pins must be open.
These pins must be open.
SMUTE
This pin must be connected to DVSS.
(2) Serial Mode
1. PCM Mode
Classification
Analog
Digital
Pin Name
AOUTLP, AOUTLN
AOUTRP, AOUTRN
DIF2
DZFL, DZFR
Setting
These pins must be open.
These pins must be open.
These pins must be connected to DVSS.
These pins must be open.
2. DSD Mode
Classification
Analog
Pin Name
AOUTLP, AOUTLN
AOUTRP, AOUTRN
DZFL, DZFR
Setting
These pins must be open.
These pins must be open.
These pins must be open.
MS1560-E-02
2014/04
-8-
[AK4495S/95]
6. Absolute Maximum Ratings
(AVSS=DVSS=VSSL=VSSR=VREFLL=VREFLR=0V; Note 1)
Parameter
Symbol
min
max
0.3
4.6
Analog
AVDD
Power Supplies:
0.3
7.5
Analog
VDDL/R
Digital
DVDD
0.3
4.6
|AVSS  DVSS| (Note 2)
GND
0.3
Input Current, Any Pin Except Supplies
IIN
10
Digital Input Voltage
VIND
0.3
DVDD+0.3
Ambient Temperature (Power applied)
Ta
40
85
Storage Temperature
Tstg
65
150
Note 1. All voltages with respect to ground.
Note 2. AVSS, DVSS, VSSL and VSSR must be connected to the same analog ground plane.
Unit
V
V
V
V
mA
V
C
C
WARNING: Operation at or beyond these limits may result in permanent damage to the device.
Normal operation is not guaranteed at these extremes.
7. Recommended Operation Conditions
(AVSS=DVSS=VSSL=VSSR =0V; Note 1)
Parameter
Symbol
min
typ
max
Power
Analog
AVDD
3.0
3.3
3.6
Supplies
Analog
VDDL/R
4.75
5.0
7.2
(Note 3)
Digital
DVDD
3.0
3.3
3.6
Voltage
“H” voltage reference VREFHL/R VDDL/R0.5
VDDL/R
Reference
“L” voltage reference VREFLL/R
VSS
(Note 4)
VREFH  VREFL
VREF
3.0
VDDL/R
Note 1. All voltages with respect to ground.
Note 3. The power up sequence between AVDD, VDDL/R and DVDD is not critical.
Note 4. The analog output voltage scales with the voltage of (VREFH  VREFL).
AOUT (typ.@0dB) = (AOUT+)  (AOUT) = 2.8Vpp  (VREFHL/R  VREFLL/R)/5.
Unit
V
V
V
V
V
V
* AKM assumes no responsibility for the usage beyond the conditions in this data sheet.
MS1560-E-02
2014/04
-9-
[AK4495S/95]
8. Electrical Characteristics
■ Handling of Unused Pin
(Ta=25C; AVDD=DVDD=3.3V; AVSS=DVSS=VSSL/R=0V; VREFHL/R=VDDL/R=5V, VREFLL/R=
VSSL/R=0V; Input data = 24bit; RL  1k; BICK=64fs; Signal Frequency = 1kHz; Sampling Frequency =
44.1kHz; Measurement bandwidth = 20Hz ~ 20kHz; External Circuit: Figure 39; unless otherwise specified.)
Parameter
min
typ
max
Unit
Resolution
32
Bits
Dynamic Characteristics
(Note 5)
0dBFS
-101
-93
dB
fs=44.1kHz
THD+N
0dBFS (VDDL/R=VREFHL/R=7.0V)
-105
dB
BW=20kHz
-57
-47
dB
60dBFS
0dBFS
fs=96kHz
-98
-88
dB
-54
-44
dB
BW=40kHz 60dBFS
0dBFS
fs=192kHz
-98
-88
dB
BW=40kHz 60dBFS
-54
-44
dB
-51
-41
dB
BW=80kHz 60dBFS
Dynamic Range (60dBFS with A-weighted) (Note 6)
114
120
dB
S/N (A-weighted)
(Note 7)
114
120
dB
S/N (A-weighted, VDDL/R=7.0V)
100
123
dB
S/N (Mono mode, A-weighted, VDDL/R=7.0V)
100
126
dB
Interchannel Isolation (1kHz)
110
120
dB
DC Accuracy
Interchannel Gain Mismatch
0.15
0.3
dB
Gain Drift
(Note 8)
20
ppm/C
Output Voltage
(Note 9)
2.65
2.8
2.95
Vpp
Load Capacitance
25
pF
Load Resistance
(Note 10)
1
k
Power Supplies
Power Supply Current
Normal operation (PDN pin = “H”)
VDDL/R
33
42
mA
AVDD
1
2
mA
DVDD (fs= 44.1kHz)
8
12
mA
DVDD (fs= 96kHz)
14
20
mA
DVDD (fs = 192kHz)
15
23
mA
Power down (PDN pin = “L”)
(Note 11)
AVDD+VDDL/R+DVDD
10
100
A
Note 5. Measured by Audio Precision, System Two. Averaging mode. Refer to the evaluation board manual.
When SC2:SC1:SC0 bit = “010”.
Note 6. Figure 39 External LPF Circuit Example 2. 101dB for 16-bit data and 118dB for 20-bit data.
Note 7. Figure 39 External LPF Circuit Example 2. S/N does not depend on input data size.
Note 8. The voltage on (VREFH  VREFL) is held +5V externally.
Note 9. Full-scale voltage(0dB). Output voltage scales with the voltage of (VREFHL/R  VREFLL/R).
AOUT (typ.@0dB) = (AOUT+)  (AOUT) = 2.8Vpp  (VREFHL/R  VREFLL/R)/5.
Note 10. Regarding Load Resistance, AC load is 1k (min) with a DC cut capacitor (Figure 39). DC load is
1.5k ohm (min) without a DC cut capacitor (Figure 38). The load resistance value is with respect to
ground. Analog characteristics are sensitive to capacitive load that is connected to the output pin.
Therefore the capacitive load must be minimized.
Note 11. In the power down mode. The PSN pin = DVDD, and all other digital input pins including clock pins
(MCLK, BICK and LRCK) are held DVSS.
MS1560-E-02
2014/04
- 10 -
[AK4495S/95]
■ Sharp Roll-Off Filter Characteristics (fs = 44.1kHz)
(Ta=25C; AVDD= DVDD=3.0  3.6V, VREFHL/R= VDDL/R =4.75  7.2V; Normal Speed Mode;
DEM=OFF; SD bit=“0” or SD pin = “L”, SLOW bit=“0” or SLOW pin = “L”)
Parameter
Symbol
min
typ
max
Unit
Digital Filter
Passband
(Note 12) 0.01dB
PB
0
20.0
kHz
6.0dB
22.05
kHz
Stopband
(Note 12)
SB
24.1
kHz
Passband Ripple
PR
0.005
dB
Stopband Attenuation
SA
100
dB
Group Delay
(Note 13)
GD
29.4
1/fs
Digital Filter + SCF
Frequency Response: 0  20.0kHz
0.2
dB
■ Sharp Roll-Off Filter Characteristics (fs = 96kHz)
(Ta=25C; AVDD= DVDD=3.0  3.6V, VREFHL/R= VDDL/R =4.75  7.2V; Double Speed Mode;
DEM=OFF; SD bit=“0” or SD pin = “L”, SLOW bit=“0” or SLOW pin = “L”)
Parameter
Symbol
min
typ
max
Unit
Digital Filter
Passband
(Note 12) 0.01dB
PB
0
43.5
kHz
6.0dB
48.0
kHz
Stopband
(Note 12)
SB
52.5
kHz
Passband Ripple
PR
0.005
dB
Stopband Attenuation
SA
100
dB
Group Delay
(Note 13)
GD
28.8
1/fs
Digital Filter + SCF
Frequency Response: 0  40.0kHz
0.3
dB
■ Sharp Roll-Off Filter Characteristics (fs = 192kHz)
(Ta=25C; AVDD= DVDD=3.0  3.6V, VREFHL/R= VDDL/R =4.75  7.2V; Quad Speed Mode;
DEM=OFF; SD bit=“0” or SD pin = “L”, SLOW bit=“0” or SLOW pin = “L”)
Parameter
Symbol
min
typ
max
Unit
Digital Filter
Passband
(Note 12) 0.01dB
PB
0
87.0
kHz
6.0dB
96.0
kHz
Stopband
(Note 12)
SB
105
kHz
Passband Ripple
PR
0.005
dB
Stopband Attenuation
SA
92
dB
Group Delay
(Note 13)
GD
28.8
1/fs
Digital Filter + SCF
Frequency Response: 0  80.0kHz
+0/1
dB
Note 12. The passband and stopband frequencies scale with fs. For example, PB=0.4535×fs (@0.01dB),
SB=0.546×fs.
Note 13. The calculating delay time which occurred by digital filtering. This time is from setting the
16/20/24bit data of both channels to input register to the output of analog signal.
MS1560-E-02
2014/04
- 11 -
[AK4495S/95]
Figure 1. Sharp Roll-off Filter Frequency Response
Figure 2. Sharp Roll-off Filter PassBand Ripple
MS1560-E-02
2014/04
- 12 -
[AK4495S/95]
■ Short Delay Sharp Roll-Off Filter Characteristics (fs = 44.1kHz)
(Ta=25C; AVDD= DVDD=3.0  3.6V, VREFHL/R= VDDL/R =4.75  7.2V; Normal Speed Mode;
DEM=OFF; SD bit=“1” or SD pin = “H”, SLOW bit=“0” or SLOW pin = “L”)
Parameter
Symbol
min
typ
max
Unit
Digital Filter
Passband
(Note 12)
0.01dB
PB
0
20.0
kHz
6.0dB
22.05
kHz
Stopband
(Note 12)
SB
24.1
kHz
Passband Ripple
PR
0.005
dB
Stopband Attenuation
SA
100
dB
Group Delay
(Note 13)
GD
6.25
1/fs
Digital Filter + SCF
Frequency Response : 0  20.0kHz
0.2
dB
■ Short Delay Sharp Roll-Off Filter Characteristics (fs = 96kHz)
(Ta=25C; AVDD= DVDD=3.0  3.6V, VREFHL/R= VDDL/R =4.75  7.2V; Double Speed Mode;
DEM=OFF; SD bit=“1” or SD pin = “H”, SLOW bit=“0” or SLOW pin = “L”)
Parameter
Symbol
min
typ
max
Unit
Digital Filter
Passband
(Note 12) 0.01dB
PB
0
43.5
kHz
6.0dB
48.0
kHz
Stopband
(Note 12)
SB
52.5
kHz
Passband Ripple
PR
0.005
dB
Stopband Attenuation
SA
100
dB
Group Delay
(Note 13)
GD
5.63
1/fs
Digital Filter + SCF
Frequency Response : 0  40.0kHz
0.3
dB
■ Short Delay Sharp Roll-Off Filter Characteristics (fs = 192kHz)
(Ta=25C; AVDD= DVDD=3.0  3.6V, VREFHL/R= VDDL/R =4.75  7.2V; Quad Speed Mode;
DEM=OFF; SD bit=“1” or SD pin = “H”, SLOW bit=“0” or SLOW pin = “L”)
Parameter
Symbol
min
typ
max
Digital Filter
Passband
(Note 12)
0.01dB
PB
0
87.0
6.0dB
96.0
Stopband
(Note 12)
SB
105
Passband Ripple
PR
0.005
Stopband Attenuation
SA
92
Group Delay
(Note 13)
GD
5.63
Digital Filter + SCF
Frequency Response : 0  80.0kHz
+0/1
-
MS1560-E-02
Unit
kHz
kHz
kHz
dB
dB
1/fs
dB
2014/04
- 13 -
[AK4495S/95]
Figure 3. Short Delay Sharp Roll-off Filter Frequency Response
Figure 4. Short Delay Sharp Roll-off Filter Passband Ripple
MS1560-E-02
2014/04
- 14 -
[AK4495S/95]
■ Slow Roll-Off Filter Characteristics (fs = 44.1kHz)
(Ta=25C; AVDD= DVDD=3.0  3.6V, VREFHL/R= VDDL/R =4.75  7.2V; Normal Speed Mode;
DEM=OFF; SD bit=“0” or SD pin = “L”, SLOW bit=“1” or SLOW pin = “H”)
Parameter
Symbol
min
typ
max
Unit
Digital Filter
Passband
(Note 12) 0.01dB
PB
0
8.1
kHz
6.0dB
18.2
kHz
Stopband
(Note 12)
SB
39.2
kHz
Passband Ripple
PR
0.005
dB
Stopband Attenuation
SA
94
dB
Group Delay
(Note 13)
GD
6.63
1/fs
Digital Filter + SCF
Frequency Response: 0  20.0kHz
0.2
dB
■ Slow Roll-Off Filter Characteristics (fs = 96kHz)
(Ta=25C; AVDD= DVDD=3.0  3.6V, VREFHL/R= VDDL/R =4.75  7.2V; Double Speed Mode;
DEM=OFF; SD bit=“0” or SD pin = “L”, SLOW bit=“1” or SLOW pin = “H”)
Parameter
Symbol
min
typ
max
Unit
Digital Filter
Passband
(Note 12) 0.01dB
PB
0
17.7
kHz
6.0dB
39.6
kHz
Stopband
(Note 12)
SB
85.3
kHz
Passband Ripple
PR
0.005
dB
Stopband Attenuation
SA
100
dB
Group Delay
(Note 13)
GD
6.00
1/fs
Digital Filter + SCF
Frequency Response: 0  40.0kHz
0.3
dB
■ Slow Roll-Off Filter Characteristics (fs = 192kHz)
(Ta=25C; AVDD= DVDD=3.0  3.6V, VREFHL/R= VDDL/R =4.75  7.2V; Quad Speed Mode;
DEM=OFF; SD bit=“0” or SD pin = “L”, SLOW bit=“1” or SLOW pin = “H”)
Parameter
Symbol
min
typ
max
Unit
Digital Filter
Passband
(Note 12) 0.01dB
PB
0
35.5
kHz
6.0dB
79.1
kHz
Stopband
(Note 12)
SB
171
kHz
Passband Ripple
PR
0.005
dB
Stopband Attenuation
SA
97
dB
Group Delay
(Note 13)
GD
6.00
1/fs
Digital Filter + SCF
Frequency Response: 0  80.0kHz
+0/1
dB
Note 14. The passband and stopband frequencies scale with fs. For example, PB=0.4535×fs (@0.01dB),
SB=0.546×fs.
Note 15. The calculating delay time which occurred by digital filtering. This time is from setting the
16/20/24bit data of both channels to input register to the output of analog signal.
MS1560-E-02
2014/04
- 15 -
[AK4495S/95]
Figure 5. Slow Roll-off Filter Frequency Response
Figure 6. Slow Roll-off Filter Passband Ripple
MS1560-E-02
2014/04
- 16 -
[AK4495S/95]
■ Short Delay Slow Roll-Off Filter Characteristics (fs = 44.1kHz)
(Ta=25C; AVDD= DVDD=3.0 3.6V, VREFHL/R= VDDL/R =4.75  7.2V; Normal Speed Mode;
DEM=OFF; SD bit=“1” or SD pin = “H” , SLOW bit=“1” or SLOW pin = “H”)
Parameter
Symbol
min
typ
max
Unit
Digital Filter
Passband
(Note 12) 0.01dB
PB
0
8.1
kHz
6.0dB
18.2
kHz
Stopband
(Note 12)
SB
39.1
kHz
Passband Ripple
PR
0.005
dB
Stopband Attenuation
SA
94
dB
Group Delay
(Note 13)
GD
5.3
1/fs
Digital Filter + SCF
Frequency Response : 0  20.0kHz
0.2
dB
■ Short Delay Slow Roll-Off Filter Characteristics (fs = 96kHz)
(Ta=25C; AVDD= DVDD=3.0  3.6V, VREFHL/R= VDDL/R =4.75  7.2V; Double Speed Mode;
DEM=OFF; SD bit=“1” or SD pin = “H” , SLOW bit=“1” or SLOW pin = “H”)
Parameter
Symbol
min
typ
max
Unit
Digital Filter
Passband
(Note 12) 0.01dB
PB
0
43.5
kHz
6.0dB
48.0
kHz
Stopband
(Note 12)
SB
85.0
kHz
Passband Ripple
PR
0.005
dB
Stopband Attenuation
SA
100
dB
Group Delay
(Note 13)
GD
4.68
1/fs
Digital Filter + SCF
Frequency Response : 0  40.0kHz
0.3
dB
■ Short Delay Slow Roll-Off Filter Characteristics (fs = 192kHz)
(Ta=25C; AVDD= DVDD=3.0  3.6V, VREFHL/R= VDDL/R =4.75  7.2V; Quad Speed Mode;
DEM=OFF; SD bit=“1” or SD pin = “H” , SLOW bit=“1” or SLOW pin = “H”)
Parameter
Symbol
min
typ
max
Digital Filter
Passband
(Note 12) 0.01dB
PB
0
87.0
6.0dB
96.0
Stopband
(Note 12)
SB
170
Passband Ripple
PR
0.005
Stopband Attenuation
SA
97
Group Delay
(Note 13)
GD
4.68
Digital Filter + SCF
Frequency Response : 0  80.0kHz
+0/1
-
MS1560-E-02
Unit
kHz
kHz
kHz
dB
dB
1/fs
dB
2014/04
- 17 -
[AK4495S/95]
Figure 7. Short Delay Slow Roll-off Filter Frequency Response
Figure 8. Short Delay Slow Roll-off Filter Passband Ripple
MS1560-E-02
2014/04
- 18 -
[AK4495S/95]
■ DC Characteristics
(Ta=25C; AVDD=DVDD=3.0  3.6, VREFHL/R=VDDL/R=4.75  7.2V)
Parameter
Symbol
min
typ
max
Unit
High-Level Input Voltage
VIH
70%DVDD
V
Low-Level Input Voltage
VIL
30%DVDD
V
High-Level Output Voltage (Iout=100A)
VOH
DVDD0.5
V
Low-Level Output Voltage
(DZFL, DZFR pins: Iout=100A)
VOL
0.5
V
(SDA pin:
Iout=3mA)
VOL
0.5
V
Input Leakage Current
(Note 16)
Iin
10
A
Note 16. The TST1/CAD0 and P/S pins have internal pull-up devices, nominally 100k. Therefore The
TST1/CAD0 and P/S pins are not included.
MS1560-E-02
2014/04
- 19 -
[AK4495S/95]
■ Switching Characteristics
(Ta=25C; AVDD=DVDD=3.0  3.6V, VREFHL/R= 4.75  7.2V)
Parameter
Symbol
Master Clock Timing
Frequency
fCLK
Duty Cycle
dCLK
LRCK Frequency
(Note 17)
1152fs, 512fs or 768fs
fsn
256fs or 384fs
fsd
128fs or 192fs
fsq
64fs
fsoc
64fs
fssd
Duty Cycle
Duty
PCM Audio Interface Timing
BICK Period
1152fs, 512fs or 768fs
tBCK
256fs or 384fs
tBCK
128fs or 192fs
tBCK
64fs
tBCK
64fs
tBCK
BICK Pulse Width Low
tBCKL
BICK Pulse Width High
tBCKH
BICK “” to LRCK Edge (Note 18)
tBLR
LRCK Edge to BICK “” (Note 18)
tLRB
SDATA Hold Time
tSDH
SDATA Setup Time
tSDS
External Digital Filter Mode
BICK Period
tB
BCK Pulse Width Low
tBL
BCK Pulse Width High
tBH
BCK “” to WCK Edge
tBW
WCK Edge to BCK “”
tWB
WCK Pulse Width Low
tWCK
WCK Pulse Width High
tWCH
DATA Hold Time
tDH
DATA Setup Time
tDS
DSD Audio Interface Timing (64 mode, fs=44.1kHz)
DCLK Period
tDCK
DCLK Pulse Width Low
tDCKL
DCLK Pulse Width High
tDCKH
DCLK Edge to DSDL/R (Note 19)
tDDD
DSD Audio Interface Timing (128 mode, fs=44.1kHz)
DCLK Period
tDCK
DCLK Pulse Width Low
tDCKL
DCLK Pulse Width High
tDCKH
DCLK Edge to DSDL/R (Note 19)
tDDD
MS1560-E-02
min
typ
max
Unit
7.7
40
49.152
60
MHz
%
30
54
108
54
108
216
kHz
kHz
kHz
kHz
kHz
%
384
768
45
55
1/128fsn
1/64fsd
1/64fsq
1/64fso
1/64fsh
10
10
5
5
5
5
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
27
10
10
5
5
54
54
5
5
ns
ns
ns
ns
ns
ns
ns
ns
ns
1/64fs
160
160
20
20
ns
ns
ns
ns
10
ns
ns
ns
ns
1/128fs
80
80
10
2014/04
- 20 -
[AK4495S/95]
Control Interface Timing
CCLK Period
tCCK
200
ns
CCLK Pulse Width Low
tCCKL
80
ns
Pulse Width High
tCCKH
80
ns
CDTI Setup Time
tCDS
50
ns
CDTI Hold Time
tCDH
50
ns
CSN High Time
tCSW
150
ns
CSN “” to CCLK “”
tCSS
50
ns
CCLK “” to CSN “”
tCSH
50
ns
Control Interface Timing (I2C Bus mode):
SCL Clock Frequency
fSCL
400
kHz
Bus Free Time Between Transmissions
tBUF
1.3
s
Start Condition Hold Time (prior to first clock pulse)
tHD:STA
0.6
s
Clock Low Time
tLOW
1.3
s
Clock High Time
tHIGH
0.6
s
Setup Time for Repeated Start Condition
tSU:STA
0.6
s
SDA Hold Time from SCL Falling
(Note 20)
tHD:DAT
0
s
SDA Setup Time from SCL Rising
tSU:DAT
0.1
s
Rise Time of Both SDA and SCL Lines
tR
0.3
s
Fall Time of Both SDA and SCL Lines
tF
0.3
s
Setup Time for Stop Condition
tSU:STO
0.6
s
Pulse Width of Spike Noise Suppressed by Input Filter
tSP
0
50
ns
Capacitive load on bus
Cb
400
pF
Reset Timing
PDN Pulse Width
(Note 21)
tPD
150
ns
Note 17. When the 1152fs, 512fs or 768fs /256fs or 384fs /128fs or 192fs are switched, the AK4495S/95
should be reset by the PDN pin or RSTN bit.
Note 18. BICK rising edge must not occur at the same time as LRCK edge.
Note 19. DSD data transmitting device must meet this time.
Note 20. Data must be held for sufficient time to bridge the 300 ns transition time of SCL.
Note 21. The AK4495S/95 can be reset by bringing the PDN pin to “L”.
MS1560-E-02
2014/04
- 21 -
[AK4495S/95]
■ Timing Diagram
1/fCLK
VIH
MCLK
VIL
tCLKH
tCLKL
dCLK=tCLKH x fCLK, tCLKL x fCLK
1/fs
VIH
LRCK
VIL
tBCK
VIH
BICK
VIL
tBCKH
tBCKL
1/fs
VIH
WCK
VIL
tB
VIH
BCK
VIL
tBH
tBL
Clock Timing
MS1560-E-02
2014/04
- 22 -
[AK4495S/95]
VIH
LRCK
VIL
tBLR
tLRB
VIH
BICK
VIL
tSDS
tSDH
VIH
SDATA
VIL
Audio Interface Timing (PCM Mode)
tDCK
tDCKL
tDCKH
VIH
DCLK
VIL
tDDD
VIH
DSDL
DSDR
VIL
Audio Serial Interface Timing (DSD Normal Mode, DCKB bit = “0”)
tDCK
tDCKL
tDCKH
VIH
DCLK
VIL
tDDD
tDDD
VIH
DSDL
DSDR
VIL
Audio Serial Interface Timing (DSD Phase Modulation Mode, DCKB bit = “0”)
MS1560-E-02
2014/04
- 23 -
[AK4495S/95]
VIH
CSN
VIL
tCSS
tCCKL tCCKH
VIH
CCLK
VIL
tCDS
CDTI
C1
tCDH
C0
R/W
VIH
A4
VIL
WRITE Command Input Timing
tCSW
VIH
CSN
VIL
tCSH
VIH
CCLK
CDTI
VIL
D3
D2
D1
D0
VIH
VIL
WRITE Data Input Timing
MS1560-E-02
2014/04
- 24 -
[AK4495S/95]
tPD
PDN
VIL
Power Down & Reset Timing
VIH
WCK
VIL
tBW
tWB
VIH
BCK
VIL
tDS
tDH
VIH
DATA
VIL
External Digital Filter I/F mode
MS1560-E-02
2014/04
- 25 -
[AK4495S/95]
9. Functional Descriptions
■ D/A Conversion Mode
In serial mode, the AK4495S/95 can perform D/A conversion for either PCM data or DSD data. The D/P bit
controls PCM/DSD mode. When DSD mode, DSD data can be input from DCLK, DSDL and DSDR pins.
When PCM mode, PCM data can be input from BICK, LRCK and SDATA pins. When PCM/DSD mode is
changed by D/P bit, the AK4495S/95 should be reset by RSTN bit. It takes about 2/fs to 3/fs to change the
mode. In parallel mode, the AK4495S/95 performs for only PCM data.
DP bit
Interface
0
PCM
1
DSD
Table 1. PCM/DSD Mode Control
When DP bit= “0”, an internal digital filter or external digital filter can be selected. When using an external
digital filter (EX DF I/F mode), data is input to each MCLK, BCK, WCK, DINL and DINR pin. EXDF bit
controls the modes. When switching internal and external digital filters, the AK4495S/95 must be reset by
RSTN bit. A Digital filter switching takes 2~3k/fs.
EXDF
Interface
bit
0
PCM
1
EX DF I/F
Table 2. Digital Filter Control (DP bit = “0”)
■ System Clock
[1] PCM Mode
The external clocks, which are required to operate the AK4495S/95, are MCLK, BICK and LRCK. MCLK
should be synchronized with LRCK but the phase is not critical. The MCLK is used to operate the digital
interpolation filter and the delta-sigma modulator. There are two modes for MCLK frequency setting: Manual
Setting Mode and Auto Setting Mode. In manual setting mode, MCLK frequency is set automatically (Table
4). In auto setting mode, sampling speed and MCLK frequency are detected automatically (Table 5) and then
the initial master clock is set to the appropriate frequency (Table 6). When the reset is released (PDN pin =
“”), the AK4495S/95 is in auto setting mode.
The AK4495S/95 is automatically placed in reset state when MCLK and LRCK are stopped during a normal
operation (PDN pin =“H”), and the analog output becomes VDDR/2 and VDDL/2 voltages (typ). When
MCLK and LRCK are input again, the AK4495S/95 exits reset state and starts operation. After exiting system
reset (PDN pin =“L”→“H”) at power-up and other situations, the AK4495S/95 is in power-down mode until
MCLK and LRCK are supplied.
The MCLK frequency corresponding to each sampling speed should be provided externally (Table 3).
MS1560-E-02
2014/04
- 26 -
[AK4495S/95]
(1) Parallel Mode (PSN pin = “H”)
1. Manual Setting Mode (ACKS pin = “L”)
The MCLK frequency corresponding to each sampling speed should be provided externally (Table 3). DFS1
bit is fixed to “0”. In this mode, quad speed mode is not available.
LRCK
MCLK (MHz)
BICK
fs
128fs
192fs
256fs
384fs
512fs
768fs
1152fs
64fs
32.0kHz
N/A
N/A
8.1920
12.2880
16.3840
24.5760
36.8640 2.0480MHz
44.1kHz
N/A
N/A
11.2896
16.9344
22.5792
33.8688
N/A
2.8224MHz
48.0kHz
N/A
N/A
12.2880
18.4320
24.5760
36.8640
N/A
3.0720MHz
Table 3. System Clock Example (Manual Setting Mode @Parallel Mode) (N/A: Not available)
In manual setting mode, the AK4495S/95 supports sampling rate from 32kHz to 96kHz (Table 4). However,
the DR and S/N performances of when MCLK=256fs/384fs will degrade approximately 3dB as compared to
when MCLK=512fs/768fs if the sampling rate is 32kHz~48kHz.
ACKS pin
MCLK
DR,S/N
L
256fs/384fs/512fs/768fs
120dB
H
256fs/384fs
117dB
H
512fs/768fs
120dB
Table 4. Relationship of MCLK Frequency and DR, S/N Performance (fs = 44.1kHz)
2. Auto Setting Mode (ACKS pin = “H”)
In auto setting mode, MCLK frequency and sampling frequency are detected automatically (Table 5). MCLK
of corresponded frequency to each sampling speed mode should be input externally. (Table 6)
MCLK
Sampling Speed
1152fs
Normal (fs32kHz)
512/256fs
768/384fs
Normal
256fs
384fs
Double
128fs
192fs
Quad
64fs
96fs
Oct
32fs
48fs
Hex
Table 5. Sampling Speed (Auto Setting Mode @Parallel Mode)
LRCK
MCLK(MHz)
Sampling
Speed
fs
32fs 48fs 64fs 96fs 128fs 192fs
256fs
384fs
512fs 768fs 1152fs
N/A
N/A
N/A
N/A
N/A
(8.192*)
(12.288*)
16.384
24.576
36.864
32.0kHz N/A
Normal/
N/A
N/A
N/A
N/A
N/A
(11.2896*) (16.9344*) 22.5792 33.8688
N/A
44.1kHz N/A
(Double*)
N/A
N/A
N/A
N/A
N/A
(12.288*)
(18.432*)
24.576
36.864
N/A
48.0kHz N/A
N/A
N/A
N/A
N/A
N/A
22.5792
33.8688
N/A
N/A
N/A
88.2kHz N/A
Double
N/A
N/A
N/A
N/A
N/A
24.576
36.864
N/A
N/A
N/A
96.0kHz N/A
N/A
N/A
N/A
22.5792 33.8688
N/A
N/A
N/A
N/A
N/A
176.4kHz N/A
Quad
N/A
N/A
N/A
24.576
36.864
N/A
N/A
N/A
N/A
N/A
192.0kHz N/A
Quad
N/A
N/A
24.576 36.864
N/A
N/A
N/A
N/A
N/A
N/A
N/A
384kHz
Oct
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
768kHz 24.576 36.864 N/A
Hex
Table 6. System Clock Example (Auto Setting Mode @Parallel Mode) (N/A: Not available)
MS1560-E-02
2014/04
- 27 -
[AK4495S/95]
When MCLK= 256fs/384fs, auto setting mode supports sampling rate of 32kHz~96kHz (Table 7). However,
the DR and S/N performances will degrade approximately 3dB as compared to when MCLK= 512fs/768fs
when the sampling rate is 32kHz~48kHz.
ACKS pin
MCLK
DR,S/N
L
256fs/384fs/512fs/768fs
120dB
H
256fs/384fs
117dB
H
512fs/768fs
120dB
Table 7. Relationship of MCLK Frequency and DR, S/N Performance (fs = 44.1kHz)
3. Digital filter
The AK4495S/95 has four kind of digital filters selected by SD and SLOW bits. Different sound qualities on
playback can be selected by these filters.
SD pin
L
L
H
H
SLOW pin
L
H
L
H
Mode
Sharp roll-off filter
Slow roll-off filter
Short delay Sharp roll-off filter
Short delay Slow roll-off filter
Table 8. Digital Filter Setting
(default)
The AK4495S/95 can be operated on a slower sampling frequency. This mode is available when the SSLOW
pin = “H”.
(2) Serial Mode (PSN pin = “L”)
1. Manual Setting Mode (ACKS bit = “0”)
MCLK frequency is detected automatically and the sampling speed is set by DFS2-0 bits (Table 9). The
MCLK frequency corresponding to each sampling speed should be provided externally (Table 10). The
AK4495S/95 is set to Manual Setting Mode at power-up (PDN pin = “L” →“H”). When DFS2-0 bits are
changed, the AK4495S/95 should be reset by RSTN bit.
DFS2
0
0
0
0
1
1
1
1
DFS1
0
0
DFS0
0
1
Sampling Rate (fs)
Normal Speed Mode
30kHz  54kHz (default)
Double Speed Mode 54kHz  108kHz
120kHz 
1
0
Quad Speed Mode
216kHz
1
1
Reserved
0
0
Oct Speed Mode
384kHz
0
1
Hex Speed Mode
768kHz
1
0
Reserved
1
1
Reserved
Table 9. Sampling Speed (Manual Setting Mode @Serial Mode)
MS1560-E-02
2014/04
- 28 -
[AK4495S/95]
LRCK
fs
32.0kHz
44.1kHz
48.0kHz
88.2kHz
96.0kHz
176.4kHz
192.0kHz
384kHz
768kHz
32fs
48fs
64fs
96fs
N/A
N/A
N/A
N/A
N/A
N/A
N/A
12.288
24.576
N/A
N/A
N/A
N/A
N/A
N/A
N/A
18.432
36.864
N/A
N/A
N/A
N/A
N/A
N/A
N/A
24.576
49.152
N/A
N/A
N/A
N/A
N/A
N/A
N/A
36.864
N/A
MCLK (MHz)
128fs 192fs 256fs
384fs
512fs
768fs
1152fs
N/A
N/A
N/A
N/A
N/A
22.5792
24.5760
49.152
N/A
12.2880
16.9344
18.4320
33.8688
36.8640
N/A
N/A
N/A
N/A
16.3840
22.5792
24.5760
N/A
N/A
N/A
N/A
N/A
N/A
24.5760
33.8688
36.8640
N/A
N/A
N/A
N/A
N/A
N/A
36.8640
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
33.8688
36.8640
N/A
N/A
8.1920
11.2896
12.2880
22.5792
24.5760
45.1584
49.152
N/A
N/A
Sampling
Speed
Normal
Double
Quad
Quad
Oct
Hex
Table 10. System Clock Example (Manual Setting Mode @Serial Mode)
2. Auto Setting Mode (ACKS bit = “1”)
MCLK frequency and the sampling speed are detected automatically (Table 11) and DFS2-0 bits are ignored.
The MCLK frequency corresponding to each sampling speed should be provided externally (Table 12).
MCLK
Sampling Speed
1152fs
Normal (fs32kHz)
512/256fs
768/384fs
Normal
256fs
384fs
Double
128fs
192fs
Quad
Table 11. Sampling Speed (Auto Setting Mode @Serial Mode)
LRCK
MCLK(MHz)
Sampling
Speed
fs
32fs 48fs 64fs 96fs 128fs 192fs
256fs
384fs
512fs 768fs 1152fs
N/A
N/A
N/A
N/A
N/A
N/A
(8.192*)
(12.288*)
16.384
24.576
36.864
32.0kHz
Normal/
N/A
N/A
N/A
N/A
N/A
(11.2896*) (16.9344*) 22.5792 33.8688
N/A
44.1kHz N/A
(Double*)
N/A
N/A
N/A
N/A
N/A
(12.288*)
(18.432*)
24.576
36.864
N/A
48.0kHz N/A
N/A
N/A
N/A
N/A
N/A
22.5792
33.8688
N/A
N/A
N/A
88.2kHz N/A
Double
N/A
N/A
N/A
N/A
N/A
24.576
36.864
N/A
N/A
N/A
96.0kHz N/A
N/A
N/A
N/A
22.5792 33.8688
N/A
N/A
N/A
N/A
N/A
176.4kHz N/A
Quad
N/A
N/A
N/A
N/A
24.576
36.864
N/A
N/A
N/A
N/A
N/A
192.0kHz
Quad
N/A
N/A
24.576 36.864
N/A
N/A
N/A
N/A
N/A
N/A
N/A
384kHz
Oct
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
768kHz 24.576 36.864 N/A
Hex
Table 12. System Clock Example (Auto Setting Mode @Serial Mode)
When MCLK= 256fs/384fs, auto setting mode supports sampling rate of 32kHz~96kHz (Table 13). However,
the DR and S/N performances will degrade approximately 3dB as compared to when MCLK= 512fs/768fs
when the sampling rate is 32kHz~48kHz.
ACKS bit
MCLK
DR,S/N
0
256fs/384fs/512fs/768fs
120dB
1
256fs/384fs
117dB
1
512fs/768fs
120dB
Table 13. Relationship of MCLK Frequency and DR, S/N Performance (fs = 44.1kHz)
MS1560-E-02
2014/04
- 29 -
[AK4495S/95]
3. Digital filter
The AK4495S/95 has four kind of digital filters selected by SD and SLOW bits. Different sound qualities on
playback can be selected by these filters.
SD bit
0
0
1
1
SLOW bit
0
1
0
1
Mode
Sharp roll-off filter
Slow roll-off filter
Short delay Sharp roll-off filter
Short delay Slow roll-off filter
Table 14. Digital Filter Setting
(default)
The AK4495S/95 can be operated on a slower sampling frequency. This mode is available when SSLOW bit =
“1” (05H D0).
MS1560-E-02
2014/04
- 30 -
[AK4495S/95]
[2] DSD Mode
The external clocks, which are required to operate the AK4495S/95, are MCLK and DCLK. MCLK should be
synchronized with DCLK but the phase is not critical. The frequency of MCLK is set by DCKS bit.
The AK4495S/95 is automatically placed in reset state when MCLK is stopped during a normal operation
(PDN pin =“H”), and the analog output becomes VDDR/2 and VDDL/2 voltages (typ.).
DCKS bit
0
1
MCLK Frequency DCLK Frequency
512fs
64fs
768fs
64fs
Table 15. System Clock (DSD Mode)
(default)
The AK4495S/95 supports DSD data stream of 2.8224MHz (64fs) and 5.6448MHz (128fs). The data sampling
speed is selected by DSDSEL bit. 2.8224MHz (64fs) is supported when DSDSEL bit = “0” and 5.6448MHz
(128fs) is supported when DSDSEL bit = “1”.
DSDSEL bit
DSD data stream
0
2.8224MHz
(default)
1
5.6448MHz
Table 16. DSD Sampling Speed Control
The AK4495S/95 has a Volume pass function. Three modes are selectable by DSDD1-0 bits.
DSDD1 bit
0
0
1
1
DSDD0 bit
0
1
Mode
Normal path
Volume pass
(default)
0
Reserved
1
Reserved
Table 17. DSD Play Back Mode Control
The AK4495S/95 has an internal mute function that mutes the output when DSD audio data becomes all “1” or
all “0” for 2048 samples (1/fs). DDM bit controls this function. When the output is muted, L channel and R
channel flags are indicated on DML bit and DMR bit, respectively. DMC bit controls mute release whether
releasing the mute automatically when the signal level returns to a normal level or releasing the mute manually
by a register. DMRE bit releases the mute when manual controlling is selected.
MS1560-E-02
2014/04
- 31 -
[AK4495S/95]
■ Audio Interface Format
[1] PCM Mode
Data is shifted in via the SDATA pin using BICK and LRCK inputs. Eight data formats are supported and
selected by the DIF2-0 pins (Parallel control mode) or DIF2-0 bits (Serial control mode) as shown in Table 18.
In all formats the serial data is MSB-first, 2's compliment format and is latched on the rising edge of BICK.
Mode 2 can be used for 20-bit and 16-bit MSB justified formats by zeroing the unused LSBs.
Mode
0
1
2
3
4
5
6
7
DIF2
0
0
0
0
1
1
1
1
DIF1
0
0
1
1
0
0
1
1
DIF0
Input Format
0
16-bit LSB justified
1
20-bit LSB justified
0
24-bit MSB justified
1
24-bit I2S compatible
0
24-bit LSB justified
1
32-bit LSB justified
0
32-bit MSB justified
1
32-bit I2S compatible
Table 18. Audio Interface Format
BICK
 32fs
 48fs
 48fs
 48fs
 48fs
 64fs
64fs
 64fs
Figure
Figure 9
Figure 10
Figure 11
Figure 12
Figure 10
Figure 13
Figure 14
Figure 15
(default)
LRCK
0
1
10
11
12
13
14
15
0
1
10
11
12
13
14
15
0
1
BICK
(32fs)
SDATA
Mode 0
15
14
6
5
1
0
14
4
3
15
16
2
17
1
0
31
15
0
14
6
5
14
1
4
15
3
16
2
17
1
0
15
31
0
14
1
BICK
(64fs)
SDATA
Mode 0
Don’t care
15
14
Don’t care
0
15
14
0
12
31
15:MSB, 0:LSB
Lch Data
Rch Data
Figure 9. Mode 0 Timing
LRCK
0
1
8
9
10
11
12
31
0
1
8
9
10
11
0
1
BICK
(64fs)
SDATA
Mode 1
Don’t care
19
0
Don’t care
19
0
Don’t care
19
0
19
0
19:MSB, 0:LSB
SDATA
Mode 4
Don’t care
23
22
21
20
23
22
21
20
23:MSB, 0:LSB
Lch Data
Rch Data
Figure 10. Mode 1/4 Timing
MS1560-E-02
2014/04
- 32 -
[AK4495S/95]
LRCK
0
1
2
22
23
24
30
31
0
1
2
22
23
24
30
31
0
1
BICK
(64fs)
SDATA
23
22
1
0
Don’t care
23
22
0
1
Don’t care
23
22
0
1
23:MSB, 0:LSB
Lch Data
Rch Data
Figure 11. Mode 2 Timing
LRCK
0
1
2
3
23
24
25
31
0
1
2
3
23
24
25
31
BICK
(64fs)
SDATA
23
0
1
22
Don’t care
23
22
0
1
23
Don’t care
23:MSB, 0:LSB
Lch Data
Rch Data
Figure 12. Mode 3 Timing
LRCK
0
1
2
20
21
22
32
33
63
0
1
2
20
21
22
32
33
63
0
1
BICK(128fs)
SDATA
31
0
1
2
12
13
14
23
1
24
0
31
31
0
1
2
12
13
14
23
1
24
0
31
0
1
BICK(64fs)
SDATA
31 30
20 19 18
9
8
1
0
31 30
Lch Data
20
19 18
9
8
1
0
31
Rch Data
31: MSB, 0:LSB
Figure 13. Mode 5 Timing
MS1560-E-02
2014/04
- 33 -
[AK4495S/95]
LRCK
0
1
2
20
21
22
32
33
63
0
1
2
20
21
22
32
33
63
0
1
BICK(128fs)
SDATA
31 30
0
1
12 11 10
2
12
13
0
14
31 30
23
24
31
0
1
12
11 10
2
12
0
13
14
31
23
24
31
0
1
BICK(64fs)
SDATA
31 30
20 19 18
8
9
0
1
31 30
20
19 18
Lch Data
8
9
0
1
31
Rch Data
31: MSB, 0:LSB
Figure 14. Mode 6 Timing
LRCK
0
1
2
20
21
22
33
34
63
0
1
2
20
21
22
33
34
63
24
25
31
0
1
BICK(128fs)
SDATA
31
0
1
13 12 11
2
12
13
0
14
31
24
25
31
0
1
13
2
12 11
12
0
13
14
0
1
BICK(64fs)
SDATA
0
31
21 20 19
8
9
1
2
0
31
21
20 19
Lch Data
9
8
2
1
0
Rch Data
31: MSB, 0:LSB
Figure 15. Mode 7 Timing
[2] DSD Mode
In case of DSD mode, DIF2-0 pins and DIF2-0 bits are ignored. The frequency of DCLK is 64fs or 128fs.
DCKB bit can invert the polarity of DCLK.
DCLK (64fs)
DCKB=1
DCLK (64fs)
DCKB=0
DSDL,DSDR
Normal
D0
DSDL,DSDR
Phase Modulation
D0
D1
D1
D2
D1
D2
D3
D2
D3
Figure 16. DSD Mode Timing
MS1560-E-02
2014/04
- 34 -
[AK4495S/95]
[3] External Digital Filter Mode (EX DF I/F Mode)
DW indicates the number of BCK in one WCK cycle. The audio data is input by MCLK, BCK and WCK from
the DINL and DINR pins. Three formats are available (Table 20) by DIF2-0 bits setting. The data is latched on
the rising edge of BCK. The BCK and MCLK clocks must be the same frequency and must not burst. BCK and
MCLK frequencies for each sampling speed are shown in Table 19.
Sampling
Speed[kHz]
MCLK&BCK [MHz]
WCK
ECS
512fs
768fs
24.576
36.864
16fs
768
0
(default)
(432-864)
32
48
DW
12.288
18.432
24.576
36.864
8fs
384
1
(216-432)
32
48
64
96
DW
Table 19 System Clock Example (EX DF I/F mode) (N/A: Not available)
256fs
N/A
384fs
N/A
Mode
DIF2
DIF1
DIF0
Input Format
0
0
0
0
16-bit LSB justified
1
0
0
1
N/A
2
0
1
0
N/A
3
0
1
1
N/A
4
1
0
0
24-bit LSB justified
5
1
0
1
32-bit LSB justified (default)
6
1
1
0
N/A
7
1
1
1
N/A
Table 20 Audio Interface Format (EX DF I/F mode) (N/A: Not available)
1/16fs or 1/8fs or 1/4fs or 1/2fs
WCK
0
1
8
9
10
11
16
17
26
27
28
29
30
31
0
1
BCK
DINL or
DINR
31
0
30
1
24 23
5
22
6
21
7
20
8
17
16
47
15
48
14
6
5
65
49
4
3
92
2
93
1
94
0
95
0
1
BCK
DINL or
DINR
Don’t care
0
1
Don’t care
5
6
7
Don’t care
8
23
24
31
17
25
2
3
44
45
1
46
0 Don’t care
47
0
1
BCK
DINL or
DINR
Don’t care
Don’t care
Don’t care
31
3
2
1
0
Don’t care
Figure 17 EX DF I/F Mode Timing
MS1560-E-02
2014/04
- 35 -
[AK4495S/95]
■ D/A Conversion Mode Switching Timing
RSTN bit
4/fs
D/A Mode
PCM Mode
DSD Mode
0
D/A Data
PCM Data
DSD Data
Figure 18. D/A Mode Switching Timing (PCM to DSD)
RSTN bit
D/A Mode
DSD Mode
PCM Mode
4/fs
D/A Data
DSD Data
PCM Data
Figure 19. D/A Mode Switching Timing (DSD to PCM)
Note. The signal range is identified as 25% ~ 75% duty ratios in DSD mode. DSD signal must not go beyond
this duty range at the SACD format book (Scarlet Book).
■ De-emphasis Filter
A digital de-emphasis filter is available for 32kHz, 44.1kHz or 48kHz sampling rates (tc = 50/15µs) and is
enabled or disabled with DEM1-0 pins or DEM1-0 bits. In case of 256fs/384fs and 128fs/192fs, the digital
de-emphasis filter is always off. When DSD mode, DEM1-0 bits are ignored. The setting value is held even if
PCM mode and DSD mode are switched.
DEM1
0
0
1
1
DEM0
Mode
0
44.1kHz
1
OFF
(default)
0
48kHz
1
32kHz
Table 21. De-emphasis Control
■ Output Volume (PCM, DSD)
The AK4495S/95 includes channel independent digital output volumes (ATT) with 255 levels at 0.5dB step
including MUTE. This volume control is in front of the DAC and it can attenuate the input data from 0dB to
–127dB or mute. When changing output levels, transitions are executed in soft change; thus no switching noise
occurs during these transitions. It takes 7424/fs to attenuate from FFH (dB) to 00H (MUTE). When initial
timing reset is executed, the attenuation level is reset to FFH. Setting RSTN bit to “0” initializes the attenuation
level to FFH and setting RSTN bit to “1” release the attenuation level to the setting value. Register values will
not be changed by switching PCM mode and DSD mode.
Transition Time
0dB to MUTE
fs = 44.1kHz
168.3ms
fs = 96kHz
77.3ms
fs = 192kHz
38.6ms
Table 22. ATT Transition Time
Sampling Speed
MS1560-E-02
2014/04
- 36 -
[AK4495S/95]
■ Zero Detection (PCM, DSD)
The AK4495S/95 has a channel-independent zeros detect function. When the input data at each channel is
continuously zeros for 8192 LRCK cycles, the DZF pin of each channel goes to “H”. The DZF pin of each
channel immediately returns to “L” if the input data of each channel is not zero after going to “H”. If the RSTN
bit is “0”, the DZF pins of both L and R channels go to “H”. The DZF pin of each channel returns to “L” in 4 ~
5/fs after the input data of each channel becomes “1” when RSTN bit is set to “1”. If DZFM bit is set to “1”, the
DZF pins of both L and R channels go to “H” only when the input data for both channels are continuously
zeros for 8192 LRCK cycles. The zero detect function can be disabled by setting the DZFE bit. In this case,
DZF pins of both channels are always “L”. The DZFB bit can invert the polarity of the DZF pin.
DZFE
DZFB
0
1
Data
DZF-pin
L
0
H
not zero
L
0
Zero detect
H
1
not zero
H
1
Zero detect
L
Table 23. Zero Detect Function and DZF Pin Output
■ Mono Output (PCM, DSD, EX DF I/F)
The AK4495S/95 can select input/output for both output channels by setting the MONO bit and SELLR bit.
This function is available for any audio format.
MONO bit
0
0
1
1
SELLR bit
Lch Out
0
Lch In
1
Rch In
0
Lch In
1
Rch In
Table 24 MONO Mode Output Select
Rch Out
Rch In
Lch In
Lch In
Rch In
■ Sound Quality Control (PCM, DSD, Ex DF I/F)
Sound quality of the AK4495S/95 can be selected by SC2-0 bits.
SC1
0
0
1
SC0
0
1
0
1
1
Mode
1
2
3
(default)
4
Table 25. SC1-0 bits Control
When SC2 bit=“1”, the AK4495S/95 operates in Mode 5.
MS1560-E-02
2014/04
- 37 -
[AK4495S/95]
■ Soft Mute Operation (PCM, DSD)
The soft mute operation is performed at digital domain. When the SMUTE pin goes to “H” or the SMUTE bit
set to “1”, the output signal is attenuated by  during ATT_DATA  ATT transition time from the current
ATT level. When the SMUTE pin is returned to “L” or the SMUTE bit is returned to “0”, the mute is cancelled
and the output attenuation gradually changes to the ATT level during ATT_DATA  ATT transition time. If
the soft mute is cancelled before attenuating  after starting the operation, the attenuation is discontinued and
returned to ATT level by the same cycle. The soft mute is effective for changing the signal source without
stopping the signal transmission.
SMUTE pin or
SMUTE bit
(1)
(1)
ATT_Level
(3)
Attenuation
-
GD
(2)
GD
(2)
AOUT
DZF pin
(4)
8192/fs
Notes:
(1) ATT_DATA  ATT transition time. For example, this time is 7424LRCK cycles (1020/fs) at
ATT_DATA=255 in Normal Speed Mode.
(2) The analog output corresponding to the digital input has group delay (GD).
(3) If the soft mute is cancelled before attenuating  after starting the operation, the attenuation is
discontinued and returned to ATT level by the same cycle.
(4) When the input data for each channel is continuously zeros for 8192 LRCK cycles, the DZF pin for each
channel goes to “H”. The DZF pin immediately returns to “L” if input data are not zero.
Figure 20. Soft Mute Function
■ System Reset
The AK4495S/95 should be reset once by bringing the PDN pin = “L” upon power-up. It initializes register
settings of the device. The analog block of the AK4495S/95 exits power-down mode by MCLK input, and the
digital block exits power-down mode after the internal counter counts MCLK for 4/fs.
MS1560-E-02
2014/04
- 38 -
[AK4495S/95]
■ Power ON/OFF timing
The AK4495S/95 is placed in the power-down mode by bringing the PDN pin “L” and the registers are
initialized. The analog outputs are floating (Hi-Z). As some click noise occurs at the edge of the PDN pin
signal, the analog output should be muted externally if the click noise influences system application.
The DAC can be reset by setting RSTN bit to “0”. In this case, registers are not initialized and the
corresponding analog outputs go to VCML/R. As some click noise occurs at the edge of RSTN signal, the
analog output should be muted externally if click noise adversely affect system performance.
Power
PDN pin
(1)
Internal
State
Normal Operation
DAC In
(Digital)
“0”data
“0”data
GD
DAC Out
(Analog)
(3)
Reset
(2)
(4)
GD
(4)
(3)
(5)
Clock In
Don’t care
Don’t care
MCLK,LRCK,BICK
(7)
DZFL/DZFR
External
Mute
(6)
Mute ON
Mute ON
Notes:
(1) After AVDD and DVDD are powered-up, the PDN pin should be “L” for 150ns.
(2) The analog output corresponding to digital input has group delay (GD).
(3) Analog outputs are floating (Hi-Z) in power-down mode.
(4) Click noise occurs at the edge of PDN signal. This noise is output even if “0” data is input.
(5) MCLK, BICK and LRCK clocks can be stopped in power-down mode (PDN pin= “L”).
(6) Mute the analog output externally if click noise (3) adversely affect system performance
The timing example is shown in this figure.
(7) DZFL/R pins are “L” in the power-down mode (PDN pin = “L”).
Figure 21. Power-down/up Sequence Example
MS1560-E-02
2014/04
- 39 -
[AK4495S/95]
■ Reset Function
(1) RESET by RSTN bit = “0”
When the RSTN bit = “0”, the AK4495S/95’s digital block is powered down, but the internal register values
are not initialized. In this time, the analog outputs go to VCML/R voltage and DZFL/DZFR pins are “H”.
Figure 22 shows an example of reset by RSTN bit.
RSTN bit
3~4/fs (5)
2~3/fs (5)
Internal
RSTN bit
Internal
State
Normal Operation
Power-down
D/A In
(Digital)
“0” data
(1)
D/A Out
(Analog)
Normal Operation
Digital Block
GD
GD
(3)
(2)
(3)
(1)
2/fs(4)
DZF
(6)
Notes:
(1) The analog output corresponding to digital input has group delay (GD).
(2) Analog outputs settle to VCOM voltage.
(3) Small pop noise occurs at the edges(“ ”) of the internal timing of RSTN bit. This noise is output
even if “0” data is input.
(4) The DZF pins change to “H” when the RSTN bit becomes “0”, and return to “L” at 2/fs after RSTN bit
becomes “1”.
(5) There is a delay, 3~4/fs from RSTN bit “0” to the internal RSTN bit “0”, and 2~3/fs from RSTN bit “1”
to the internal RSTN bit “1”.
(6) Mute the analog output externally if click noise (3) and Hi-Z (2) adversely affect system performance
Figure 22. Reset Sequence Example 1
MS1560-E-02
2014/04
- 40 -
[AK4495S/95]
(2) RESET by MCLK or LRCK/WCK Stop
The AK4495S/95 is automatically placed in reset state when MCLK or LRCK is stopped during PDM mode
(PDN pin =“H”), and the analog outputs are floating (Hi-Z). When MCLK and LRCK are input again, the
AK4495S/95 exits reset state and starts the operation. Zero detect function is disable when MCLK or LRCK is
stopped. In DSD mode the AK4495S/95 is in reset state when MCLK is stopped, and it is in reset state when
MCLK and WCK are stopped in external digital filter mode.
AVDD pin
DVDD pin
RSTB pin
(1)
Internal
State
Power-down
D/A In
(Digital)
Power-down
Normal Operation
Normal Operation
(3)
GD
D/A Out
(Analog)
Digital Circuit Power-down
(2)
GD
(4)
Hi-Z
(5)
(2)
(4)
(4)
(5)
Clock In
MCLK, BICK, LRCK Stop
MCLK, BICK, LRCK
External
MUTE
(6)
(6)
(6)
Notes:
(1) After AVDD and DVDD are powered-up, the PDN pin should be “L” for 150ns.
(2) The analog output corresponding to digital input has group delay (GD).
(3) The digital data can be stopped. Click noise after MCLK and LRCK are input again can be reduced by
inputting “0” data during this period.
(4) Click noise occurs within 3 ~ 4LRCK cycles from the riding edge (“↑”) of the PDN pin or MCLK
inputs. This noise occurs even when “0” data is input.
(5) Clocks (MCLK, BICK, LRCK/WCK) can be stopped in the reset state (MCLK or LRCK/WCK is
stopped).
(6) Mute the analog output externally if click noise (4) influences system applications. The timing example
is shown in this figure.
Figure 23. Reset Sequence Example 2
MS1560-E-02
2014/04
- 41 -
[AK4495S/95]
■ Synchronize Function
The AK4495S/95 has a function that resets the internal counter to synchronize with the external clock edge in
a range of 3/256fs. Clock synchronize function becomes valid if SYNCE bit is set to “1” during operation in
PCM mode or EXDF mode and input data of both L and R channels are “0” for 8129 times continuously or
RESTN bit is “1”. In PCM mode, the internal counter is synchronized with a falling edged of LRCK (rising
edge of LRCK in I2C mode), and it is synchronized with a falling edge of WCK in EXDF mode. In this case,
the analog output has the same voltage as VCML/R. Figure 24 shows a synchronizing sequence when the input
data is “0” for 8192 times continuously. Figure 25 shows a synchronizing sequence by RSTN bit.
(1) Synchronization by continuous “0” data input for 8192 times
If the input data is “0” for 8192 times continuously, or if the data becomes “0” for 8192 times continuously by
attenuation, the DZFL/DZFR pin goes to “H” and the synchronize function becomes valid. The synchronize
function is enabled only when both L and R channels data are “0” for 8192 times continuously. Figure 24
shows a synchronizing sequence when the input data is “0” for 8192 times continuously.
D/A In
(Digital)
SMUTE
(1)
(1)
ATT_Level
Attenuation
-
GD
GD
(4)
AOUT
DZF pin
(2)
8192/fs
(2)
8192/fs
SYNC
Operation (2)
Internal Counter
Reset
Internal
Data Reset
GD
SYNC
Operation (2)
(5)
4~5/fs (3)
Note:
(1) ATT_DATA  ATT transition time. For example, this time is 7424LRCK cycles (1020/fs) at
ATT_DATA=255 in Normal Speed Mode.
(2) When both L and R channels data are “0” for 8192 times continuously, DZFL/R pins become “H” and
the synchronize function is valid.
(3) Internal data is fixed to “0” forcibly for 4 to 5/fs when internal counter is reset.
(4) A click noise may occur when the internal counter is reset. This noise is output even if a “0” data is input.
Mute the analog output externally if this click noise affects the system performance.
(5) When the internal clock and external clock are in synchronization, the internal counter is not reset even if
the synchronize function is valid.
Figure 24. Synchronizing Sequence by Continuous “0” Data Input for 8192 Times
MS1560-E-02
2014/04
- 42 -
[AK4495S/95]
(2) Synchronization by RSTN bit
If RSTN bit is set to “0”, the output signal of the DZFL/DZFR pin becomes “H”. Then, the DAC is reset 3 to
4/fs after the DZFL/DZFR pin = “H” and the analog output becomes the same voltage as VCML/R. The
synchronize function becomes valid when both of the DZFL and DZFR pins output “H”. Figure 25 shows a
synchronizing sequence by RSTN bit.
RSTN bit
3~4/fs (4)
2~3/fs (4)
Internal
RSTN bit
Internal
State
Normal Operation
D/A In
(Digital)
force”0” (2)
(3)
D/A Out
(Analog)
Normal Operation
Digital Block Power-down
GD
GD (3)
(5)
(5)
2/fs(4)
DZF
SYNC Operation (1)
Internal Counter
Reset
Internal
Data Reset
4~5/fs (2)
Note:
(1) DZFL/R pin becomes “H” by a rising edge of RSTN bit, and becomes “L” 2/fs after a falling edge of
internal signal of RSTN bit. The synchronize function is valid During the DZFL/R pin = “H”.
(2) Internal data is fixed to “0” forcibly for 4 to 5/fs when the internal counter is reset.
(3) Since the analog output corresponding to digital input has group delay (GD), it is recommended to have
a no-input period longer than the group delay before writing “0” to RSTN bit.
(4) It takes 3 to 4/fs when falling to change the internal RSTN signal of the LSI after writing to RSTN bit.
It also takes 3 to 4/fs when rising to change the internal RSTN signal of the LSI. The synchronize
function becomes valid immediately when “0” is written to RSTN bit. Therefore, there is a case that the
internal counter is reset before internal RSTN signal of the LSI is changed.
(5) A click noise occurs on the rising or falling edge of the internal RSTN signal and when the internal
counter is reset. This noise is output even if a “0” data is input. Mute the analog output externally if this
click noise affects the system performance.
Figure 25. Synchronizing Sequence by RSTN bit
MS1560-E-02
2014/04
- 43 -
[AK4495S/95]
■ Register Control Interface
(1) 3-wire Serial Control Mode (I2C pin = “L”)
Pins (parallel control mode) or registers (serial control mode) can control the functions of the AK4495S/95. In
parallel control mode, the register setting is ignored, and in serial control mode the pin settings are ignored.
When the state of the PSN pin is changed, the AK4495S/95 should be reset by the PDN pin. The serial control
interface is enabled by the PSN pin = “L”. Internal registers may be written to through3-wire µP interface pins:
CSN, CCLK and CDTI. The data on this interface consists of Chip address (2-bits, C1/0), Read/Write (1-bit;
fixed to “1”), Register address (MSB first, 5-bits) and Control data (MSB first, 8-bits). The data is output on a
falling edge of CCLK and the data is received on a rising edge of CCLK. The writing of data is valid when
CSN “”. The clock speed of CCLK is 5MHz (max).
Function
Parallel Control Mode Serial Control Mode
Audio Format
Y
Y
Auto Setting Mode
Y
Y
De-emphasis
Y
Y
SMUTE
Y
Y
DSD Mode
Y
EX DF I/F
Y
Zero Detection
Y
Sharp Roll off filter
Y
Y
Slow Roll off filter
Y
Y
Minimum delay Filter
Y
Y
Digital Attenuator
Y
Sound Quality Adjustment
Y
Clock Synchronize
Y
Table 26. Function List1 (Y: Available, -: Not available)
Setting the PDN pin to “L” resets the registers to their default values. In serial control mode, the internal timing
circuit is reset by the RSTN bit, but the registers are not initialized.
CSN
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
CCLK
CDTI
C1 C0 R/W A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0
C1-C0: Chip Address (C1 bit =CAD1 pin, C0 bit =CAD0 pin)
R/W: READ/WRITE (Fixed to “1”, Write only)
A4-A0: Register Address
D7-D0: Control Data
Figure 26. Control I/F Timing
* 3-wire serial control mode does not support read commands.
* When the AK4495S/95 is in power down mode (PDN pin = “L”) or the MCLK is not provided, writing into
control registers is prohibited.
* The control data can not be written when the CCLK rising edge is 15 times or less or 17 times or more during
CSN is “L”.
MS1560-E-02
2014/04
- 44 -
[AK4495S/95]
(2) I2C-bus Control Mode (I2C pin = “H”)
The AK4495S/95 supports the fast-mode I2C-bus (max: 400kHz, Ver 1.0).
(2)-1. WRITE Operations
Figure 27 shows the data transfer sequence for the I2C-bus mode. All commands are preceded by a START
condition. A HIGH to LOW transition on the SDA line while SCL is HIGH indicates a START condition
(Figure 33). After the START condition, a slave address is sent. This address is 7 bits long followed by the
eighth bit that is a data direction bit (R/W). The most significant five bits of the slave address are fixed as
“00100”. The next bits are CAD1 and CAD0 (device address bits). This bit identifies the specific device on the
bus. The hard-wired input pin (cAD1pins, CAD0 pin) sets these device address bits (Figure 28). If the slave
address matches that of the AK4495S/95, the AK4495S/95 generates an acknowledge and the operation is
executed. The master must generate the acknowledge-related clock pulse and release the SDA line (HIGH)
during the acknowledge clock pulse (Figure 34). A R/W bit value of “1” indicates that the read operation is to
be executed, and “0” indicates that the write operation is to be executed.
The second byte consists of the control register address of the AK4495S/95 and the format is MSB first.
(Figure 29). The data after the second byte contains control data. The format is MSB first, 8bits (Figure 30).
The AK4495S/95 generates an acknowledge after each byte is received. Data transfer is always terminated by
a STOP condition generated by the master. A LOW to HIGH transition on the SDA line while SCL is HIGH
defines a STOP condition (Figure 33).
The AK4495S/95 can perform more than one byte write operation per sequence. After receipt of the third byte
the AK4495S/95 generates an acknowledge and awaits the next data. The master can transmit more than one
byte instead of terminating the write cycle after the first data byte is transferred. After receiving each data
packet the internal address counter is incremented by one, and the next data is automatically taken into the next
address. If the address exceeds 2FH prior to generating a stop condition, the address counter will “roll over” to
00H and the previous data will be overwritten.
The data on the SDA line must remain stable during the HIGH period of the clock. HIGH or LOW state of the
data line can only be changed when the clock signal on the SCL line is LOW (Figure 35) except for the START
and STOP conditions.
S
T
A
R
T
SDA
S
S
T
O
P
R/W= “0”
Slave
Address
Sub
Address(n)
A
C
K
Data(n)
Data(n+1)
A
C
K
A
C
K
Data(n+x)
A
C
K
A
C
K
P
A
C
K
Figure 27. Data Transfer Sequence at I2C Bus Mode
0
0
1
0
0
CAD1
CAD0
R/W
(CAD0 is set by the pin)
Figure 28. The First Byte
0
0
0
A4
A3
A2
A1
A0
D1
D0
Figure 29. The Second Byte
D7
D6
D5
D4
D3
D2
Figure 30. The Third Byte and After The Third Byte
MS1560-E-02
2014/04
- 45 -
[AK4495S/95]
(2)-2. READ Operations
Set the R/W bit = “1” for the READ operation of the AK4495S/95. After transmission of data, the master can
read the next address’s data by generating an acknowledge instead of terminating the write cycle after the
receipt of the first data word. After receiving each data packet the internal address counter is incremented by
one, and the next data is automatically taken into the next address. If the address exceeds 09H prior to
generating stop condition, the address counter will “roll over” to 00H and the data of 00H will be read out.
The AK4495S/95 supports two basic read operations: CURRENT ADDRESS READ and RANDOM
ADDRESS READ.
(2)-2-1. CURRENT ADDRESS READ
The AK4495S/95 has an internal address counter that maintains the address of the last accessed word
incremented by one. Therefore, if the last access (either a read or write) were to address “n”, the next
CURRENT READ operation would access data from the address “n+1”. After receipt of the slave address with
R/W bit “1”, the AK4495S/95 generates an acknowledge, transmits 1-byte of data to the address set by the
internal address counter and increments the internal address counter by 1. If the master does not generate an
acknowledge but generates a stop condition instead, the AK4495S/95 ceases the transmission.
S
T
A
R
T
SDA
S
S
T
O
P
R/W= “1”
Slave
Address
Data(n)
A
C
K
Data(n+1)
A
C
K
Data(n+2)
A
C
K
Data(n+x)
A
C
K
A
C
K
P
A
C
K
Figure 31. Current Address Read
(2)-2-2. RANDOM ADDRESS READ
The random read operation allows the master to access any memory location at random. Prior to issuing the
slave address with the R/W bit “1”, the master must first perform a “dummy” write operation. The master
issues a start request, a slave address (R/W bit = “0”) and then the register address to read. After the register
address is acknowledged, the master immediately reissues the start request and the slave address with the R/W
bit “1”. The AK4495S/95 then generates an acknowledge, 1 byte of data and increments the internal address
counter by 1. If the master does not generate an acknowledge but generates a stop condition instead, the
AK4495S/95 ceases the transmission.
S
T
A
R
T
SDA
S
S
T
A
R
T
R/W= “0”
Slave
Address
Sub
Address(n)
A
C
K
S
A
C
K
S
T
O
P
R/W= “1”
Slave
Address
Data(n)
A
C
K
Data(n+1)
A
C
K
Data(n+x)
A
C
K
A
C
K
P
A
C
K
Figure 32. Random Address Read
MS1560-E-02
2014/04
- 46 -
[AK4495S/95]
SDA
SCL
S
P
start condition
stop condition
Figure 33. Start Condition and Stop Condition
DATA
OUTPUT BY
TRANSMITTER
not acknowledge
DATA
OUTPUT BY
RECEIVER
acknowledge
SCL FROM
MASTER
2
1
8
9
S
clock pulse for
acknowledgement
START
CONDITION
Figure 34. Acknowledge (I2C Bus)
SDA
SCL
data line
stable;
data valid
change
of data
allowed
Figure 35. Bit Transfer (I2C Bus)
MS1560-E-02
2014/04
- 47 -
[AK4495S/95]
Function List
Function
Attenuation Level
Default
0dB
Address
03H
04H
Disable
00H
16fs(fs=44.1kHz)
00H
24bit MSB justified 00H
Disable
01H
Separated
01H
Sharp roll-off filter 01H
OFF
01H
Normal Operation
01H
PCM mode
02H
512fs
02H
PCM
DSD
EX DF I/F
Y
Y
-
External Digital Filter I/F Mode
EXDF
Y
Ex DF I/F mode clock setting
ECS
Audio Data Interface Modes
DIF2-0
Y
Data Zero Detect Enable
DZFE
Y
Data Zero Detect Mode
DZFM
Y
Minimum delay Filter Enable
SD
Y
De-emphasis Response
DEM1-0
Y
Soft Mute Enable
SMUTE
Y
DSD/PCM Mode Select
DP
Y
Master Clock Frequency Select
DCKS
at DSD mode
MONO mode Stereo mode
Stereo
02H
MONO
Y
select
Inverting Enable of DZF
“H” active
02H
DZFB
Y
The data selection of L channel R channel
02H
SELLR
Y
and R channel
Sound Quality Adjustment
Natural Sound
08H
SC[2:0]
Y
Clock Synchronize
Not Available
07H
SYNCE
Y
Table 27. Function List2 (Y: Available, -: Not available)
Y
Y
Y
Y
Y
Y
Y
-
Y
-
Y
Y
Y
-
Y
Y
Y
-
Y
-
MS1560-E-02
Bit
ATT7-0
2014/04
- 48 -
[AK4495S/95]
■ Register Map
Addr
00H
01H
02H
03H
04H
05H
06H
07H
08H
09H
Register Name
Control 1
Control 2
Control 3
Lch ATT
Rch ATT
Control4
Control5
Control6
Control7
Reserved
D7
ACKS
DZFE
DP
ATT7
ATT7
INVL
DDM
0
0
0
D6
EXDF
DZFM
0
ATT6
ATT6
INVR
DML
0
0
0
D5
ECS
SD
DCKS
ATT5
ATT5
0
DMR
0
0
0
D4
0
DFS1
DCKB
ATT4
ATT4
0
DMC
0
0
0
D3
DIF2
DFS0
MONO
ATT3
ATT3
0
DMRE
0
0
0
D2
DIF1
DEM1
DZFB
ATT2
ATT2
0
DSDD1
0
SC2
0
D1
DIF0
DEM0
SELLR
ATT1
ATT1
DFS2
DSDD0
0
SC1
0
D0
RSTN
SMUTE
SLOW
ATT0
ATT0
SSLOW
DSDSEL
SYNCE
SC0
0
Notes:
Data must not be written into addresses from 07H to 1FH.
When the PDN pin goes to “L”, the registers are initialized to their default values.
When RSTN bit is set to “0”, only the internal timing is reset, and the registers are not initialized to their
default values.
When the state of the PSN pin is changed, the AK4495S/95 should be reset by the PDN pin.
■ Register Definitions
Addr Register Name
00H Control 1
Default
D7
ACKS
0
D6
EXDF
0
D5
ECS
0
D4
0
0
D3
DIF2
0
D2
DIF1
1
D1
DIF0
0
D0
RSTN
0
RSTN: Internal Timing Reset
0: Reset. All registers are not initialized. (default)
1: Normal Operation
Writing “0” to this bit resets the internal timing circuit but register values are not initialized.
When the PSN pin = “H”, the AK4495S/95 operates regardless of the register setting.
DIF2-0: Audio Data Interface Modes (Table 18)
Initial value is “010” (Mode 2: 24-bit MSB justified).
ECS: EX DF I/F mode clock setting (Table 19)
0: 768kHz sampling rate (default)
1: 386kHz sampling rate
EXDF: External Digital Filter I/F Mode (Serial mode only)
0: Disable: Internal Digital Filter mode (default)
1: Enable: External Digital Filter mode
ACKS: Master Clock Frequency Auto Setting Mode Enable (PCM only)
0: Disable: Manual Setting Mode (default)
1: Enable: Auto Setting Mode
When ACKS bit = “1”, MCLK frequency and the sampling frequency are detected automatically.
MS1560-E-02
2014/04
- 49 -
[AK4495S/95]
Addr Register Name
01H Control 2
Default
D7
DZFE
0
D6
DZFM
0
D5
SD
1
D4
DFS1
0
D3
DFS0
0
D2
DEM1
0
D1
DEM0
1
D0
SMUTE
0
SMUTE: Soft Mute Enable
0: Normal Operation (default)
1: DAC outputs soft-muted.
DEM1-0: De-emphasis Response
Initial value is “01” (OFF).
DFS1-0: Sampling Speed Control
Initial value is “000” (Normal Speed). Click noise occurs when DFS2-0 bits are changed.
SD:
DFS2
0
0
DFS1
0
0
0
1
0
1
1
1
1
1
0
0
1
1
DFS0
0
1
Sampling Rate (fs)
Normal Speed Mode
30kHz  54kHz (default)
Double Speed Mode
54kHz  108kHz
120kHz 
0
Quad Speed Mode
216kHz
1
Reserved
0
Oct Speed Mode
384kHz
1
Hex Speed Mode
768kHz
0
Reserved
1
Reserved
Table 9. Sampling Speed (Manual Setting Mode @Serial Mode)
Minimum delay Filter Enable
0: Traditional filter
1: Short delay filter (default)
SD
0
0
1
1
SLOW
Mode
0
Sharp roll-off filter
1
Slow roll-off filter
0
Short delay sharp roll off filter
1
Short delay slow roll off filter
Table 14. Digital Filter Setting
(default)
DZFM:
Data Zero Detect Mode
0: Channel Separated Mode (default)
1: Channel ANDed Mode
If the DZFM bit is set to “1”, the DZF pins of both L and R channels go to “H” only when the
input data at both channels are continuously zeros for 8192 LRCK cycles.
DZFE:
Data Zero Detect Enable
0: Disable (default)
1: Enable
Zero detect function can be disabled by DZFE bit “0”. In this case, the DZF pins of both channels
are always “L”.
MS1560-E-02
2014/04
- 50 -
[AK4495S/95]
Addr Register Name
02H Control 3
Default
SLOW:
D7
DP
0
D6
0
0
D5
DCKS
0
D4
DCKB
0
D3
MONO
0
D2
DZFB
0
D1
SELLR
0
D0
SLOW
0
Slow Roll-off Filter Enable
0: Sharp roll-off filter (default)
1: Slow roll-off filter
SD
0
0
1
1
SLOW
Mode
0
Sharp roll-off filter
1
Slow roll-off filter
0
Short delay sharp roll off filter (default)
1
Short delay slow roll off filter
Table 14. Digital Filter Setting
SELLR: The data selection of L channel and R channel, when MONO mode
0: All channels output L channel data, when MONO mode. (default)
1: All channels output R channel data, when MONO mode.
This bit is enabled when MONO bit is “1”. The AK4495S/95 outputs Lch data to both channels
when SELLR bit is “0” and outputs Rch data to both channels when SELLR bit is “1”.
DZFB: Inverting Enable of DZF
0: DZF pin goes “H” at Zero Detection (default)
1: DZF pin goes “L” at Zero Detection
DZFE
DZFB
0
1
Data
DZF-pin
L
0
H
not zero
L
0
Zero detect
H
1
not zero
H
1
Zero detect
L
Table 23. Zero Detect Function and DZF Pin Output
MONO: MONO mode Stereo mode select
0: Stereo mode (default)
1: MONO mode
When MONO bit is “1”, MONO mode is enabled.
DCKB: Polarity of DCLK (DSD Only)
0: DSD data is output from DCLK falling edge. (default)
1: DSD data is output from DCLK rising edge.
DCKS: Master Clock Frequency Select at DSD mode (DSD only)
0: 512fs (default)
1: 768fs
DP:
DSD/PCM Mode Select
0: PCM Mode (default)
1: DSD Mode
When D/P bit is changed, the AK4495S/95 should be reset by RSTN bit.
MS1560-E-02
2014/04
- 51 -
[AK4495S/95]
Addr Register Name
03H Lch ATT
04H Rch ATT
Default
D7
ATT7
ATT7
1
D6
ATT6
ATT6
1
D5
ATT5
ATT5
1
D4
ATT4
ATT4
1
D3
ATT3
ATT3
1
D2
ATT2
ATT2
1
D1
ATT1
ATT1
1
D0
ATT0
ATT0
1
ATT7-0: Attenuation Level
255 levels, 0.5dB step
Data
FFH
FEH
FDH
:
:
02H
01H
00H
Attenuation
0dB
-0.5dB
-1.0dB
:
:
-126.5dB
-127.0dB
MUTE (-)
The transition between set values is soft transition of 7425 levels. It takes 7424/fs
(168ms@fs=44.1kHz) from FFH (0dB) to 00H (MUTE). If the PDN pin goes to “L”, the ATTs are
initialized to FFH. The ATTs are FFH when RSTN bit= “0”. When RSTN return to “1”, the ATTs fade
to their current value. This digital attenuator is independent of soft mute function.
Addr Register Name
05H Control 4
Default
D7
INVL
0
D6
INVR
0
D5
0
0
D4
0
0
D3
0
0
D2
0
0
D1
DFS2
0
D0
SSLOW
0
SSLOW: Super Slow roll off Filter Enable
0: Disable (default)
1: Enable
DFS2: Sampling Speed Control (Table 9)
Initial value is “000” (Normal Speed). Click noise occurs when DFS2-0 bits are changed.
(01H, D4, D3: DFS1-0 bits)
DFS2
0
0
0
0
1
1
1
1
DFS1
0
0
DFS0
0
1
Sampling Rate (fs)
Normal Speed Mode
30kHz  54kHz (default)
Double Speed Mode
54kHz  108kHz
120kHz 
1
0
Quad Speed Mode
216kHz
1
1
Reserved
0
0
Oct Speed Mode
384kHz
0
1
Hex Speed Mode
768kHz
1
0
Reserved
1
1
Reserved
Table 9. Sampling Speed (Manual Setting Mode @Serial Mode)
INVR:
AOUTR Output Phase Inverting
0: Disable (default)
1: Enable
INVL:
AOUTL Output Phase Inverting
0: Disable (default)
1: Enable
MS1560-E-02
2014/04
- 52 -
[AK4495S/95]
Addr Register Name
06H Control 5
Default
D7
DDM
0
D6
DML
0
D5
DMR
0
D4
DMC
0
D3
DMRE
0
D2
DSDD1
0
D1
DSDD0
0
D0
DSDSEL
0
DSDSEL: DSD sampling speed control
0: 2.8MHz (64fs) (default)
1: 5.6MHz (128fs)
DSDSEL bit DSD data stream
0
2.8224MHz
(default)
1
5.6448MHz
Table 16. DSD Sampling Speed Control
DSDD1-0: DSD play back path control
DSDD1
DSDD0
Mode
0
0
Normal path
(default)
0
1
Volume pass
1
0
Reserved
1
1
Reserved
Table 17. DSD Play Back Mode Control
DMRE: DSD mute release
0: Hold (default)
1: Release Mute
This register is only valid when DDM bit = “1” and DMC bit = “1”. When the AK4495S/95
mutes DSD data by DDM and DMC bits settings, the mute is released by setting DMRE bit to
“1”.
DMC: DSD mute control
0: Auto Return (default)
1: Mute Hold (manual return)
This register is only valid when DDM bit = “1”. It selects the mute releasing mode of when the
DSD data level becomes under full-scale after the AK4495S/95 mutes DSD data by DDM bit
setting.
DDM: DSD data mute
0: Disable (default)
1: Enable
The AK4495S/95 has an internal mute function that mutes the output when DSD audio data
becomes all “1” or all “0” for 2048sample (1/fs). DDM bit controls this function.
MS1560-E-02
2014/04
- 53 -
[AK4495S/95]
Addr Register Name
07H Control 6
Default
D7
0
0
D6
0
0
D5
0
0
D4
0
0
D3
0
0
D2
0
0
D1
0
0
D0
SYNCE
0
SYNCE: Synchronization control
0: Disable (default)
1: Enable
This register enables the function that synchronizes multiple AK4495S/95s when using more than
one AK4495S/95s in a system.
Addr Register Name
08H Control 7
Default
D7
0
0
D6
0
0
D5
0
0
D4
0
0
D3
0
0
D2
SC2
0
D1
SC1
0
D0
SC0
0
D1
0
0
D0
0
0
SC1-0: Sound control bit
SC1
0
0
SC0
0
1
1
1
Mode
1
2
(default)
0
3
1
4
Table 25. SC1-0 bits Control
SC2: Sound position control bit
0: Disable (default)
1: Sound Mode 5
Addr Register Name
09H Reserved
Default
D7
0
0
D6
0
0
D5
0
0
MS1560-E-02
D4
0
0
D3
0
0
D2
0
0
2014/04
- 54 -
[AK4495S/95]
10. Recommended External Circuits
Figure 36 shows the system connection diagram. Figure 38, Figure 39 and Figure 40 show the analog output
circuit examples. The evaluation board (AKD4495/AKD4495S) demonstrates the optimum layout, power
supply arrangements and measurement results.
5
WCK
6
SMUTE/CSN
7
SD/CCLK/SCL
Micro-
8
SLOW/CDTI/SDA
Controller
9
DIF0/DZFL
34
VCOML 35
Lch Out
Rch
LPF
Rch
Mute
Rch Out
0.1u 10u
+
VSSL 30
VSSL 29
NC 28
VSSR 27
N
0.1u 10u
VSSR 26
+
VDDR 24
0.1u
+ 10u
Digital
Ground
Lch
Mute
AOUTLP
VREFLL 36
VREFLL 37
AVSS 41
22 AOUTRP
AOUTRN 23
21 VCMR
15 DEM1
14 DEM0
13 I2C
11 DIF2/CAD0
12 PSN
VDDL 31
VDDR 25
10 DIF1/DZFR
Lch
LPF
AOUTLN 33
VDDL 32
20 VREFLR
LRCK
0.1u
VREFHL 38
4
0.1u
19 VREFLR
SDATA
VREFHL 39
3
10u
+
AK4495S/95
BICK
10u
+
18 VREFHR
PDN
2
17 VREFHR
1
DVSS 43
DSP
MCLK 42
DVDD 44
0.1u
AVDD 40
10u
+
0.1u
+
16 ACKS/CAD1
10u
Analog 5.0V
Analog 3.3V
Digital 3.3V
0.1u
+ 10u
Analog
Ground
+
Electrolytic Capacitor
Ceramic Capacitor
Notes:
- Chip Address = “00”. BICK = 64fs, LRCK = fs
- Power lines of AVDD and DVDD should be distributed separately from the point with low impedance of
regulator etc.
- AVSS, DVSS, VSSL, VSSR, VREFLL, VREFLR must be connected to the same analog ground plane.
- When AOUT drives a capacitive load, some resistance should be connected in series between AOUT and
the capacitive load.
- All input pins except pull-down/pull-up pins should not be allowed to float.
Figure 36. Typical Connection Diagram (AVDD=3.3V, VDDL/R = 5.0V, DVDD=3.3V, Serial control mode)
MS1560-E-02
2014/04
- 55 -
[AK4495S/95]
VDDR 24
VCOMR 21
36 VREFLL
VREFLR 20
37 VREFLL
Controller
AOUTLP 23
VSSR 26
VDDR 25
NC 28
VSSR 27
VSSL 29
VSSL 30
VDDL 31
AOUTRP 22
34 AOUTLP
35 VCOML
VREFLR 19
38 VREFHL
VREFHR 18
AK4495S/95
39 VREFHL
VREFHR 17
DEM0 14
10 DIF1/DZFR
I2C 13
9 DIF0/DZFL
8 SLOW/CDTI/SDA
7 SD/CCLK/SCL
1 PDN
44 DVDD
6 SMUTE/CSN
43 DVSS
5 WCK/SSLOW
DEM1 15
42 MCLK
4 LRCK/DSDR/DINR
41 AVSS
3 SDATA/DSDL/DINL
ACKS/CAD1 16
2 BICK/DCLK/BCK
40 AVDD
11 DIF2/CAD0
System
VDDL 32
Analog Ground
AOUTLN 33
Digital Ground
PSN 12
Figure 37. Ground Layout
1. Grounding and Power Supply Decoupling
To minimize coupling by digital noise, decoupling capacitors should be connected to AVDD, VDDL/R and
DVDD respectively. AVDD and VDDL/R are supplied from analog supply in system and DVDD is supplied
from digital supply in system. Power lines of AVDD, VDDL/R and DVDD should be distributed separately
from the point with low impedance of regulator etc. The power up sequence between AVDD, VDDL/R and
DVDD is not critical. AVSS, DVSS, VSSL, VSSR must be connected to the same analog ground
plane. Decoupling capacitors for high frequency should be placed as near as possible to the supply pin.
2. Voltage Reference
The differential voltage between VREFHL/R and VREFLL/R sets the analog output range. The VREFHL/R pin
is normally connected to AVDD, and the VREFLL/R pin is normally connected to VSS1/2/3. VREFHL/R and
VREFLL/R should be connected with a 0.1µF ceramic capacitor as near as possible to the pin to eliminate the
effects of high frequency noise. No load current may be drawn from VCML/R pin. All signals, especially
clocks, should be kept away from the VREFHL/R and VREFLL/R pins in order to avoid unwanted noise
coupling into the AK4495S/95.
3. Analog Outputs
The analog outputs are full differential outputs and 2.8Vpp (typ, VREFHL/R  VREFLL/R = 5V) centered
around VDDR/2 and VDDL/2 voltages. The differential outputs are summed externally, VAOUT = (AOUT+) 
(AOUT) between AOUT+ and AOUT. If the summing gain is 1, the output range is 5.6Vpp (typ, VREFHL/R
 VREFLL/R = 5V). The bias voltage of the external summing circuit is supplied externally. The input data
format is 2's complement. The output voltage (VAOUT) is a positive full scale for 7FFFFFH (@24bit) and a
negative full scale for 800000H (@24bit). The ideal VAOUT is 0V for 000000H(@24bit).
The internal switched-capacitor filters attenuate the noise generated by the delta-sigma modulator beyond the
audio passband. Figure 38 shows an example of external LPF circuit summing the differential outputs by an
op-amp. Figure 39 shows an example of differential outputs and LPF circuit example by three op-amps.
MS1560-E-02
2014/04
- 56 -
[AK4495S/95]
AK4495S/95
1.5k
AOUT-
1.5k
390
1n
+Vop
2.2n
1.5k
AOUT+
1.5k
Analog
Out
390
1n
-Vop
Figure 38. External LPF Circuit Example 1 for PCM (fc = 99.2kHz, Q=0.704)
Frequency Response
Gain
20kHz
0.011dB
40kHz
0.127dB
80kHz
1.571dB
Table 28. Frequency Response of External LPF Circuit Example 1 for PCM
+15
3.3n
+
100u
180
AOUTL- +
10k
330
7
3
2 +
* 4
3.9n
-15
10u
0.1u
6
NJM5534D
+
10u
0.1u
620
+
+
330
7
3
+
2 4
3.9n
680
100
6
1.0n NJM5534D
Lch
g
10u
0.1u
6
NJM5534D
1.2k
10k
AOUTL+
180
2 - 4
+
3
7
560
620
3.3n
100u
+10u
1.0n
1.2k
680
0.1u
560
+
0.1u
10u
+
10u
0.1u
Figure 39. External LPF Circuit Example 2 for PCM
1st Stage
2nd Stage
Total
Cut-off Frequency
182kHz
284kHz
Q
0.637
Gain
+3.9dB
-0.88dB
+3.02dB
20kHz
-0.025
-0.021
-0.046dB
Frequency
40kHz
-0.106
-0.085
-0.191dB
Response
80kHz
-0.517
-0.331
-0.848dB
Table 29. Frequency Response of External LPF Circuit Example 2 for PCM
MS1560-E-02
2014/04
- 57 -
[AK4495S/95]
It is recommended for SACD format book (Scarlet Book) that the filter response at SACD playback is an analog
low pass filter with a cut-off frequency of maximum 50kHz and a slope of minimum 30dB/Oct. The
AK4495S/95 can achieve this filter response by combination of the internal filter (Table 30) and an external
filter (Figure 40).
Frequency
Gain
20kHz
0.4dB
50kHz
2.8dB
100kHz
15.5dB
Table 30. Internal Filter Response at DSD Mode
2.0k
1.8k
4.3k
AOUT1.0k
270p
2.8Vpp
2200p
+Vop
3300p
2.0k
1.8k
1.0k
+
AOUT+
+
-
2.8Vpp
4.3k
270p
Analog
Out
6.34Vpp
-Vop
Figure 40. External 3rd Order LPF Circuit Example for DSD
Frequency
Gain
20kHz
0.05dB
50kHz
0.51dB
100kHz
16.8dB
DC gain = 1.07dB
Table 31. 3rd Order LPF (Figure 40) Response
MS1560-E-02
2014/04
- 58 -
[AK4495S/95]
11. Package
■ Outline Dimensions (AK4495S)
44-pin LQFP (Unit: mm)
1.60max
12.0
1.40 0.05
0.100.05
10.0
23
33
1.00
0.80
12.0
22
10.0
34
12
44
1
11
0.37 +0.08
–0.07
0.20
M
0.1450.055
07
S
0.60.15
0.10
S
■ Material & Lead finish
Package molding compound:
Lead frame material:
Lead frame surface treatment:
Epoxy, Halogen (bromine and chlorine) free
Cu
Solder (Pb free) plate
MS1560-E-02
2014/04
- 59 -
[AK4495S/95]
■ Outline Dimensions (AK4495)
44-pin LQFP (Unit: mm)
1.70max
12.0
0 ~ 0.2
10.0
23
33
0.80
12.0
22
10.0
34
12
44
1
11
0.09 ~ 0.20
0.370.10
010
0.600.20
0.15
■ Material & Lead finish
Package molding compound:
Lead frame material:
Lead frame surface treatment:
Epoxy, Halogen (bromine and chlorine) free
Cu
Solder (Pb free) plate
MS1560-E-02
2014/04
- 60 -
[AK4495S/95]
■ Marking (AK4495S)
AK4495SEQ
XXXXXXX
AKM
1
1) AKM Logo
2) Pin #1 indication
3) Date Code: XXXXXXX(7 digits)
4) Marking Code: AK4495S
5) Audio 4 pro Logo
■ Marking (AK4495)
AK4495EQ
XXXXXXX
AKM
1
1) AKM Logo
2) Pin #1 indication
3) Date Code: XXXXXXX(7 digits)
4) Marking Code: AK4495
5) Audio 4 pro Logo
MS1560-E-02
2014/04
- 61 -
[AK4495S/95]
12. Revision History
Date (Y/M/D)
13/11/15
14/02/25
14/04/17
Revision Reason
00
First Edition
01
Error
Correction
02
Description
Addition
Page
Contents
47
■ Register Definitions
The description of SELLR bit was changed.
■ Ordering Guide, Outline Dimensions, Marking
The AK4495 was added to this document.
2. Features
THD+N: “-105dB (Analog Block Power Supply 7V)”
was added.
DR, S/N: “120dB” was added.
8. Electrical Characteristics
Dynamic Characteristics, THD+N fs=44.1kHz, 0dBFS
VDDL/R=VREFHL/R=7.0Vwas added: -105dB (typ)
Figure 1 ~ 8 were added.
5, 56,
57
2
10
Error
Correction
12, 14,
16, 18
27
■ System Clock
Table 3 was changed.
27, 29
53-54
Table 6 and Table 12 were changed.
■ Register Definitions
Address 0x06: “Control 4” → “Control 5”
Address 0x07: “Control 5” → “Control 6”
Address 0x08: “Control 6” → “Control 7”
Address 0x09: “Control 7” → “Reserved”
MS1560-E-02
2014/04
- 62 -
[AK4495S/95]
IMPORTANT NOTICE
0. Asahi Kasei Microdevices Corporation (“AKM”) reserves the right to make changes to the
information contained in this document without notice. When you consider any use or application of
AKM product stipulated in this document (“Product”), please make inquiries the sales office of AKM
or authorized distributors as to current status of the Products.
1. All information included in this document are provided only to illustrate the operation and application
examples of AKM Products. AKM neither makes warranties or representations with respect to the
accuracy or completeness of the information contained in this document nor grants any license to any
intellectual property rights or any other rights of AKM or any third party with respect to the
information in this document. You are fully responsible for use of such information contained in this
document in your product design or applications. AKM ASSUMES NO LIABILITY FOR ANY
LOSSES INCURRED BY YOU OR THIRD PARTIES ARISING FROM THE USE OF SUCH
INFORMATION IN YOUR PRODUCT DESIGN OR APPLICATIONS.
2. The Product is neither intended nor warranted for use in equipment or systems that require
extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may
cause loss of human life, bodily injury, serious property damage or serious public impact, including
but not limited to, equipment used in nuclear facilities, equipment used in the aerospace industry,
medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic
signaling equipment, equipment used to control combustions or explosions, safety devices, elevators
and escalators, devices related to electric power, and equipment used in finance-related fields. Do not
use Product for the above use unless specifically agreed by AKM in writing.
3. Though AKM works continually to improve the Product’s quality and reliability, you are responsible
for complying with safety standards and for providing adequate designs and safeguards for your
hardware, software and systems which minimize risk and avoid situations in which a malfunction or
failure of the Product could cause loss of human life, bodily injury or damage to property, including
data loss or corruption.
4. Do not use or otherwise make available the Product or related technology or any information
contained in this document for any military purposes, including without limitation, for the design,
development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or
missile technology products (mass destruction weapons). When exporting the Products or related
technology or any information contained in this document, you should comply with the applicable
export control laws and regulations and follow the procedures required by such laws and regulations.
The Products and related technology may not be used for or incorporated into any products or systems
whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or
regulations.
5. Please contact AKM sales representative for details as to environmental matters such as the RoHS
compatibility of the Product. Please use the Product in compliance with all applicable laws and
regulations that regulate the inclusion or use of controlled substances, including without limitation,
the EU RoHS Directive. AKM assumes no liability for damages or losses occurring as a result of
noncompliance with applicable laws and regulations.
6. Resale of the Product with provisions different from the statement and/or technical features set forth
in this document shall immediately void any warranty granted by AKM for the Product and shall not
create or extend in any manner whatsoever, any liability of AKM.
7. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior
written consent of AKM.
MS1560-E-02
2014/04
- 63 -