Data Sheet

[AP3603]
AP3603
High Power Dual Output Step-Up DC-DC Controller
1. General Description
The AP3603 is a dual output step-up DC-DC controller. The output voltage can be set up to 60V by an
external feedback resistor. A wide input range of 6.4V to 20V is available, which is possible to realize a high
power boost source from the battery or the other power sources. The AP3603 supports either 200W×2ch dual
outputs or 400W×1ch dual phase single output. PWM switching frequency is set from 40kHz to 500kHz by
an external resistor. As the protective functions, it has output over voltage protection and over current
protection. The AP3603 is housed in a space-saving 20-pin HTSSOP package.
2. Features









Input Voltage Range
6.4 to 20V
Oscillation Frequency Setting Range
40k to 500kHz(Set by external resistor)
8V Gate Driver for External N-channel MOSFET(ON resistance : 3Ω)
Over Temperature Protection
Output Over Voltage Protection
Quasi-Foldback Over Current Protection
Accuracy of Feedback Voltage
+3% /-2 % (Tj=-40~145℃)
Dual Output or Dual Phase Single Output Application is Selectable
Package
20-pin HTSSOP
1
1
2
3
4
5
3
4
5
6
Vin
Vin
R1
A
2
6
R1
A
C1
A
A
C1
L1
L1
R7
R9
R8
B
C8
C7
C9
C
R10
R11
PWON
FSYN
RSP1
RT
RSN1
FB1
DRV1
CC1
GND2
GND1
VDD
SS
V8
CC2
V4
R7
D1
R3
M1
C2
C8
B
C7
M2
C6
DRV2
PWON
RSN2
MDC
RSP2
C
CH-2 VoutC
R5
L2
Size
Date:
File:
3
R10
R11
C3
RSN1
FB1
DRV1
CC1
GND2
GND1
VDD
Number
R2
C5
V4
FB2
DRV2
PWON
RSN2
MDC
RSP2
M2
C6
5
L2
Title
R2
Number
Revision
A4
Date:
File:
1
2
3
D
2014/09/12
C:\Users\..\AP3603_140912.SchDoc
4
Sheet of
Drawn By :
5
6
Dual Phase Application
Output
Voltage
Power Amplifier
12V
20V
Booster 200W class
6.4V
12V
Booster 400W class
6.4V
12V
Output
Current
CH-1 7.5A
CH-2 7.5A
CH-1 17A
CH-2 17A
34A
015000004-E-02
Output
Power
CH-1 150W
CH-2 150W
CH-1 204W
CH-2 204W
400W
Circuit
Dual Output
Dual Output
Dual Phase Single Output
2015/07
-1-
B
D2
6
Input
Voltage
C2
C
PWON
D
Sheet of
Drawn By :
R3
C4
V8
CC2
D
4
Vout
Size
Revision
2014/09/12
C:\Users\..\AP3603do_140912.SchDoc
D1
M1
R4
R12
Dual Output Application
Applications
RSP1
RT
R6
A4
D
FSYN
SS
C9
D2
Title
2
B
R4
FB2
R8
C4
C5
R12
1
R9
CH-1 Vout
[AP3603]
3. Table of Contents
1.
2.
3.
4.
5.
6.
General Description ........................................................................................................................................... 1
Features .............................................................................................................................................................. 1
Table of Contents............................................................................................................................................... 2
Block Diagram................................................................................................................................................... 3
Ordering Guide .................................................................................................................................................. 3
Pin Configurations and Functions...................................................................................................................... 4
■ Pin Configurations ....................................................................................................................................... 4
■ Functions ..................................................................................................................................................... 5
7. Absolute Maximum Ratings .............................................................................................................................. 6
8. Recommended Operating Conditions ................................................................................................................ 6
9. Electrical Characteristics ................................................................................................................................... 7
10. Functional Descriptions ..................................................................................................................................... 8
10.1 Basic Operation ..................................................................................................................................... 8
10.2 Shut Down ............................................................................................................................................. 8
10.3 Power On Sequence ............................................................................................................................... 8
10.4 Soft Start ................................................................................................................................................ 8
10.5 Power Down Sequence .......................................................................................................................... 8
10.6 Over Voltage Protection ........................................................................................................................ 8
10.7 Quasi-Foldback Over Current Protection (PWM operation) ................................................................. 8
10.8 CC1 and CC2 Pin Voltage (Error Amplifier output) Clamping Function ............................................. 9
10.9 External Synchronous Operation ........................................................................................................... 9
11. Timing Chart.................................................................................................................................................... 10
12. Application Information .................................................................................................................................. 11
12.1 Output Voltage Setting ........................................................................................................................ 11
12.2 Operational Frequency Setting ............................................................................................................ 11
12.3 Maximum ON Duty Setting ................................................................................................................. 11
12.4 Maximum Output Voltage ................................................................................................................... 11
13. Attention of PCB Layout ................................................................................................................................. 12
■ Recommended Layout ............................................................................................................................... 12
■ GND Layout .............................................................................................................................................. 12
■ Switching Node Layout ............................................................................................................................. 12
■ Current Sense Resistor Layout .................................................................................................................. 12
■ Feedback Pin Layout ................................................................................................................................. 12
■ Capacitors for V8, V4 and SS.................................................................................................................... 12
■ Bypass Capacitor ....................................................................................................................................... 12
14. Typical Characteristics .................................................................................................................................... 13
15. Recommended External circuits ...................................................................................................................... 14
■
Recommended External Circuit of Dual Output .................................................................................. 14
■
Parts List .............................................................................................................................................. 14
■
Recommended External Circuit of Dual Phase Single Output ............................................................ 15
■
Parts List .............................................................................................................................................. 15
16. Package ............................................................................................................................................................ 16
■ Outline Dimensions ................................................................................................................................... 16
■ Marking ..................................................................................................................................................... 16
17. Revise History ................................................................................................................................................. 17
Add 10.7 Quasi-Foldback Over Current Protection (PWM operation) ........................................................... 17
IMPORTANT NOTICE .......................................................................................................................................... 18
015000004-E-02
2015/07
-2-
[AP3603]
4. Block Diagram
Iss
V5
SS
SS
VDD
Vref
V 5R eg .
RSP1 UVLOcomp
GND1
V5 UVLOcomp
+
Vref
V ref
PWON
+
Vref
-
PWON
VO OVPcomp
Reset
Level Shift1
Vcnt.
3.6V
FB1
+
FBamp1
iRAMP
Reset
-
MDC
Vref
Max Duty Control
+
Reset
-
RSP2 UVLOcomp
+
Control Logic
Set
OCLcomp1
Vref
FSYN
V8
V 8R eg .
+
Level Shift2
-
CSamp2
+
Vcnt.
3.6V
FB2
+
FBamp2
VDD
iRAMP
V4
Vref
V8
SS
+
RSN2
RT
OSC
V8 UVLOcomp
-
RSP2
Vref
-
-
CC2
+
Reset
PWMcomp1
+
CC1
FB
VDD OVPcomp
SS
+
RSN1
Vrefx1.35
-
VDD
CSamp1
RSP1
+
PWMcomp2
Reset
-
DRV1
Vref
-
OCLcomp2
+
Reset
-
DRV2
GND2
5. Ordering Guide
AP3603
-40~125°C
20-pin HTSSOP
015000004-E-02
2015/07
-3-
[AP3603]
6. Pin Configurations and Functions
■ Pin Configurations
FSYN
1
20
RSP1
RT
2
19
RSN1
FB1
3
18
DRV1
CC1
4
17
GND2
GND1
5
16
VDD
SS
6
15
V8
CC2
7
14
V4
FB2
8
13
DRV2
PWON
9
12
RSN2
11
RSP2
MDC
(Top View)
Exposed Pad
10
015000004-E-02
2015/07
-4-
[AP3603]
■ Functions
No. Pin Name
I/O
1
FSYN
I
2
RT
I
3
FB1
I
4
CC1
O
5
GND1
-
6
SS
O
7
CC2
O
8
FB2
I
9
PWON
I
10
MDC
O
11
12
13
RSP2
RSN2
DRV2
I
I
O
14
V4
O
15
V8
O
16
VDD
-
17
GND2
-
18
19
20
DRV1
RSN1
RSP1
O
I
I
Function
External Synchronous Pin
This pin switches boost N-channel MOSFET of CH1 ON, synchronizing the falling
edge of input clock. The pin is pulled-up by 10uA constant current internally.
PWM Frequency Setting Pin
Connect the resistor to GND1 for setting the PWM frequency.
Refer 12.2 Operational Frequency Setting to calculate the resistance.
CH1 Output Voltage Feedback Pin
Output voltage is controlled so that FB1 pin voltage becomes 3.6V. Connect the
feedback resistance between the positive side of output capacitor and GND1, and
voltage divide node of feedback resistance should be connected to FB1 pin.
CH1 Error Amplifier Output Pin
Connect the resistance and capacitor in parallel between CC1 pin and SS pin to
compensate phase stability.
Signal Ground Pin
Connect GND2 at just below the AP3603 to prevent potential difference between
this pin and the GND2 pin.
CH1 and CH2 Soft Start Pin
Connect a capacitor between SS pin and GND to set the soft start time. When the
capacitor value is 0.1uF, the soft start time becomes 12ms.
CH2 Error Amplifier Output Pin
Connect the resistance and capacitor in parallel between CC2 pin and SS pin to
compensate phase stability.
CH2 Output Voltage Feedback Pin
Connect the feedback resistance between the positive side of output capacitor and
GND1 during dual output application usage. Voltage divide node of feedback
resistance should be connected to FB2 pin.
Connect this pin to FB1 pin at the dual phase single output application usage.
Power On Signal Input Pin
After “H” signal input, the internal voltage source V5 is powered up and then the
start-up sequence is initiated.
Maximum On Duty Set Pin
Set the maximum on time by the external resistance connecting between MDC and
GND1.
CH2 Current Detect Positive Pin
CH2 Current Detect Negative Pin
CH2 N-channel MOSFET Drive Pin
V4 Linear Regulator Output Pin
Middle voltage node of boost driver. Connect MLCC 0.22μF or more between V4
pin and GND2 to stabilize the internal voltage.
V8 Linear Regulator Output Pin
Power source of Boost driver. Connect MLCC 2.2μF or more between V8 and
GND2 to stabilize the internal voltage.
Main Power Source Pin
Power Ground Pin
Connect the GND1 at just below the AP3603 to prevent potential difference between
this pin and the GND1 pin.
CH1 N-channel MOSFET Drive Pin
CH1 Current Detect Negative Pin
CH1 Current Detect Positive Pin
015000004-E-02
2015/07
-5-
[AP3603]
7. Absolute Maximum Ratings
Parameter
Symbol
min
-0.3
Voltage between VDD, RSP1, RSP2, RSN1, RSN2 and GND
Voltage between CC1, CC2, MDC, SS, FB1, FB2, RT, FSYN,
-0.3
PWON, V4 and GND
-0.3
Voltage between V8, DRV1, DRV2 and GND
-0.3
Voltage between V8 and V4
-0.3
Voltage between RSP1and RSN1, RSP2 and RSN2
Tstg
-40
Storage Ambient Temperature Range
Tj
-40
Junction Temperature
PD
Power Dissipation (Ta=25°C)
Note 1. GND=GND1=GND2
Note 2. Connect GND1 and GND2 at just below the AP3603 on PCB.
Note 3. Junction to Ambient Thermal Resistance θJA= 40°C /W
Ambient temperature of 25ºC using JEDEC 4L board. (114.3mm×76.2mm)
max
40
Unit
V
6
V
12
6
6
150
145
3000
V
V
V
°C
°C
mW
WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal
operation is not guaranteed at these extremes.
3500
POWER DISSIPATON [mW]
3000
2500
2000
1500
1000
125℃ 500mW
500
0
-55
-30
-5
20
45
70
95
120
145
OPERATING AMBIENT TEMPERATURE Ta ℃
[ ]
Figure 1. Power Dissipation
8. Recommended Operating Conditions
Parameter
Symbol
min
typ
max
Unit
Operating input voltage range
Vin
6.4
20
V
Operating ambient temperature
Ta
-40
125
°C
WARNING: AKM assumes no responsibility for the usage beyond the conditions in this data sheet.
015000004-E-02
2015/07
-6-
[AP3603]
9. Electrical Characteristics
(VVDD=12V,Tj=-40~145°C unless otherwise specified.)
Parameter
Symbol
min
typ
max
Unit
Output Voltage Range
8V Driver Power Source
4V Drive Power Source
Feedback Voltage
Vout
V8
V4
VrefFB
7.6
3.7
3.51
8.0
4.0
3.58
60
8.3
4.2
3.69
V
V
V
V
Shutdown Current 1
ISDN1
-
-
10
uA
Shutdown Current 2
ISDN2
-
-
2
uA
Static Circuit Current1
ISUPPLY1
-
-
3.5
uA
Static Circuit Current2
ISUPPLY2
-
-
250
uA
Power-ON Voltage
Power-OFF Voltage
Power-ON Pin Current “H”
Power-ON Pin Current “L”
V8 Output Under Voltage
Protection(UVP)
V8 UVP Hysteresis
RSP Input Under Voltage
Protection(UVP)
RSP Input Under Voltage
Protection Release
Soft Start Pin Charge Current
Soft Start Time
VPWON
VPWOFF
IPWONON
IPWONOFF
2.4
-
15
-
0.6
1.5
V
V
uA
uA
V8UVP
5.0
5.28
5.6
V
V8UVLOhys
0.2
0.28
0.4
V
RSPUVP
3.5
3.75
4.2
V
4.2
4.5
4.8
V
ISSON
TSS
8.5
-
10
12
11.5
-
uA
ms
Over Current Detect Voltage
VOCL
80
100
120
mV
OVP
130
139
150
%
VDDOVP
21.5
-
-
V
Fclk
-14
0
14
%
40k~500kHz setting
Dual Phase 80k~1000kHz
Fsync
80
-
120
%
Fclk(typ)Ratio.
Vsync
0.6
-
2.4
V
External N-channel MOSFET
Switching Time
(Note 4)
Trise
80
100
150
ns
Tfall
20
55
150
ns
Minimum On Time
Minimum Off Time
Thermal Protection Operating
Temperature (Note 4,Note 5)
Thermal Protection Hysteresis
(Note 4,Note 5)
MINON
MINOFF
-
200
250
-
ns
ns
TSD
-
175
-
°C
TSDhys
-
15
-
°C
Output Over Voltage
Protection
VDD Over Voltage Protection
Oscillation Frequency
External Synchronous Clock
Input Range
External Synchronous Clock
Input threshold
RSPUVLO
Condition
VDD supply, VDD=10~20V,
PWON=0V
RSP1/2supply, RSP1/2 =10~
36V, PWON=0V
VDD supply
RSP1/2 supply, RSP1/2 =10~
36V
VPWON=5V(Input Current)
VPWON=0V(Output Current)
DIS
Css=0.1uF
Voltage between RSP and
RSN
Ratio to Reference Voltage of
Feedback
CL=10nF 10%to90%
VVDD=13V f=250kHz
CL=10nF 90%to10%
VVDD=13V f=250kHz
RMDC>127kΩ
Note 4. Guaranteed by design.
Note 5. This function protects the AP3603 against an overheat situation. However, it does not guarantee the
operation under the condition that the overheat situation beyond the specifications continues.
015000004-E-02
2015/07
-7-
[AP3603]
10. Functional Descriptions
10.1
Basic Operation
The AP3603 operates in current mode PWM controlling. The feedback voltage (FB1 pin and FB2 pin) is
compared to an internal reference voltage by an error amplifier. Then the output of an error amplifier (CC1
pin and CC2 pin) is converted into a current reference which compares to the inductance current. The ON
time of an external N-channel MOSFET continues until the inductor current reaches to the current reference.
The inductor current is detected by the current sensing resistor (R1 and R2) which is connected between RSP
and RSN. When the current reaches the target, the external N-channel MOSFET turns off and the AP3603
continues these cycles for the asynchronous PWM operation.
10.2
Shut Down
Even if the main power supply (VVDD) is supplied, the AP3603 is in shutdown status if the PWON pin is “L”.
Under this condition, the shutdown current is maximum 10uA.
10.3
Power On Sequence
When PWON pin becomes “H” from “L”, V5 and UVLO circuits start up. After V5 starts up, the voltage
reference and the over temperature protection circuits start. The AP3603 starts up protective circuit, V4
circuit and V8 circuits if it judges it is not under the over temperature condition. After V8 circuit has settled
to 8V, internal oscillation and soft start sequence start. Starting time of V8 is estimated as 4ms(typ) under the
typical application condition using recommended components.
10.4
Soft Start
This function raise the output voltage gradually by limiting current and voltage, to prevent an over shoot
when the output voltage is powered up. When a reset signal from the internal power supply circuit is
released, the AP3603 start charging to an external capacitor connected to SS pin by a constant current and
soft start operation is finished when the reference voltage reaches 1.2V. During this time, the current limit
value and the over voltage detection value is changed in proportion to the external capacitor voltage. The
start-up time of the output voltage depends on the output capacitor values and load conditions. These values
are calculated by following equation.
・Over current protection: 100mV(typ)×SS pin voltage /1.2V (Voltage between RSP pin and RSN pin)
・Over voltage protection: Setting Output voltage×SS pin voltage /1.2V
10.5
Power Down Sequence
If PWON pin becomes “L” from “H” during PWM operation, the AP3603 stops switching and shunts SS pin.
Only V8 circuit is shut down as internal circuit.
10.6
Over Voltage Protection
This function monitors the feedback voltage and turns off an external N-channel MOSFET in case the output
voltage beyond +139% from setting voltage.
10.7
Quasi-Foldback Over Current Protection (PWM operation)
AP3603 monitors the coil current by the voltage difference between RSP and RSN during on-time of external
N-channel MOSFET. When the difference reaches 100mV fixed value, AP3603 turns off the external N-channel
MOSFET and prevents coil and MOSFET from destruction. This OCL protection operates every switching cycle
and so switching continues.
015000004-E-02
2015/07
-8-
[AP3603]
10.8
CC1 and CC2 Pin Voltage (Error Amplifier output) Clamping Function
The voltage of CC pin (CC1 and CC2) which is the output of error amplifier stays around 1.2V (SS pin
voltage) under the condition of normal PWM operation. The feedback response goes worse in case the
voltage difference between CC pin (CC1 and CC2) and 1.2V becomes large under the abnormal condition
like the output voltage beyond setting voltage. It causes the over shoot or under shoot. The AP3603 clamps
the voltage of CC pin (CC1 and CC2) as below to prevent CC pin (CC1 and CC2) voltage from going out of
a normal operating condition
Detect condition
Release condition
Operation
CCx pin voltage≦0.9V
or
FBx pin voltage≦3.6V×75%
Switching command has requested
or
FBx pin voltage≧3.6V×85%
CCx pin connects to SS pin and
Error Amplifier output
disconnect to CCx pin
10.9
External Synchronous Operation
External synchronization is available by an input timing signal to the FSYN pin. The AP3603 enters external
synchronous operation mode when edge of FSYN turns off the external MOSFET connected to DRV2. If the
high level input of FSYN continues more than 1 cycle of internal CLK, the AP3603 change the
synchronization from external clock to internal oscillator. The input signal to the FSYN pin for
synchronization must be 50% duty. FSYN pin must be open in case of no use of external synchronous
operation. The AP3603 does not operate if FSYN pin connect to GND because internal OSC does not
generate the clock signal. At the case of using an external synchronous operation, FSYN pin must be open
before and during startup. And input the external clock to FSYN pin after V8 voltage reach the target (8V
) approximately.
内部発振
Internal
OSC
50%
50%
50%
50%
外部同期
External
SYNC
内部発振
Internal
OSC
内部CLK
Internal CLK
FSYN
FSYN(外部CLK)
(External CLK)
Precede
internal clock in input High
Hi入力時は内部CLK優先
DRV1
DRV1
DRV2
DRV2
固定オフ時間
Fixed
OFF time
外部同期可能
Available
external
Sync
外部同期可能
Available
external
Sync
外部同期開始
Enter
external
Sync
外部同期解除
Exit
external
Sync
Figure 2. External Synchronous Timing Chart
015000004-E-02
2015/07
-9-
[AP3603]
11. Timing Chart
VDD(RSP)
PWON
TSD
V5
V4
4.2 ms
4.2ms
V8
12ms
SS
OCL&OVP制御
OCL&OVP
control
PWM制御
PWM
control
100%
OCL Level
0%
OVP Level
100%
139%
0%
3.6V
FB(VOUT)
DRV
Figure 3.Timing Chart
015000004-E-02
2015/07
- 10 -
[AP3603]
12. Application Information
12.1 Output Voltage Setting
Output voltage is settled by feedback resistors that are connected between the output capacitor and the GND.
The value of R3, R4 (output capacitor-FB pin) and R5, R6(FB pin-GND1) is calculated by the next
equations.
CH1 Vout =3.6   1 
R3
 [ V]
R4
CH2 Vout =3.6   1 
R5
 [ V]
R6
12.2 Operational Frequency Setting
Operational frequency is settled by the resistor R7 between the RT pin and the GND. The value of the
resistor is calculated by the next equations.
R7=
0.5
1.2V

[Ω]
Frequency Hz 3.2pF  1.5V  4
12.3 Maximum ON Duty Setting
Maximum On duty is settled by the resistor between MDC pin and GND. The value of the resistor is
calculated by the next equations.
RMDC [Ω]
Duty(typ) [%]
10k
60%
27k
70%
47k
80%
82k
90%
127k or more
(Note 6)
Note 6. Maximum ON duty is fixed by the operational frequency and minimum off time 250ns (typ). If
f>250kHz, duty may be limited by the minimum off time of the IC.
Max Duty=(1  250ns  Frequency)  100 [%]
12.4 Maximum Output Voltage
The maximum output voltage depends on maximum ON duty. It is estimated by the next equation.
Vin
Max Vout =
[V]
1.1  Duty
015000004-E-02
2015/07
- 11 -
[AP3603]
13. Attention of PCB Layout
■ Recommended Layout
Figure 4. Top Layer
Figure 5. Top Layer Silk
Figure 7. Bottom Layer Silk
Figure 6. Bottom Layer
■ GND Layout
GND plane should be as large as possible. The output capacitor and input capacitor should be connected to
the same ground plane.
■ Switching Node Layout
The switching node line between external N-channel MOSFETs, the Schottky barrier diode and power
inductor should be thick and short. Wiring to the DRV1 and DRV2 should be as short as possible.
■ Current Sense Resistor Layout
A current sense resistor should be located as close as possible to the AP3603 so that the wirings to the RSP
pin and the RSN pin from the both ends of the current sense resistor have the same resistance.
■ Feedback Pin Layout
Feedback resistors connected in series between the output capacitor and the GND should be connected as
near as possible to the output capacitor and as far as possible from the switching node. The middle point of
feedback two resistors should be as close as possible to the FB pin.
■ Capacitors for V8, V4 and SS
Capacitors between V8 pin and GND2, V4 pin and GND2, SS pin and GND1 should be connected as near
as possible to the each terminals of the AP3603.
■ Bypass Capacitor
The bypass capacitor between the VDD pin and the GND2 should be connected as near as possible to the
AP3603.
015000004-E-02
2015/07
- 12 -
[AP3603]
14. Typical Characteristics
1.22
100
Vin=6.0[V]
Vin=7.0[V]
Vin=8.0[V]
Vin=9.0[V]
Vin=10.0[V]
Vin=11.0[V]
Vin=12.0[V]
90
80
60
1.207
Vref[V]
efficiency[%]
70
1.213
50
1.2
40
1.193
30
20
1.187
10
1.18
-50
0
0
1
2
3
4
5
7
Iout[A]
8
9
10
11
12
0
50
100
150
Ta[℃]
Figure 8. Efficiency 12V Output
Figure 9. Vref vs. Ta
13.2
Iout= 0.0[A]
Iout= 1.0[A]
Iout= 2.0[A]
Iout= 3.0[A]
Iout= 4.0[A]
Iout= 5.0[A]
Iout= 6.0[A]
Iout= 7.0[A]
Iout= 8.0[A]
Iout= 9.0[A]
Iout=10.0[A]
Iout=11.0[A]
Iout=12.0[A]
13.0
12.8
12.6
Vout[V]
12.4
12.2
12.0
11.8
11.6
11.4
11.2
11.0
10.8
6
7
8
9
Vin[V]
10
11
12
Figure 10. Line Regulation 12V Output
13.2
Vin= 6.0[V]
13
Vin= 7.0[V]
12.8
Vin= 8.0[V]
12.6
Vin= 9.0[V]
Vin=10.0[V]
12.4
Vin=11.0[V]
Vin=12.0[V]
Vout[V]
12.2
12
11.8
11.6
11.4
11.2
11
10.8
0
1
2
3
4
5
6
7
Iout[A]
8
9
10
11
12
Figure 11. Load Regulation 12V Output
015000004-E-02
2015/07
- 13 -
[AP3603]
15. Recommended External circuits
■ Recommended External Circuit of Dual Output
1
2
3
4
5
6
Vin
R1
A
A
C1
L1
R7
R9
R8
B
C8
C7
C9
C
R10
R11
PWON
FSYN
RSP1
RT
RSN1
FB1
DRV1
CC1
GND2
GND1
VDD
SS
V8
CC2
V4
FB2
DRV2
PWON
RSN2
MDC
RSP2
D1
CH-1 Vout
R3
M1
C2
B
C4
R4
C5
M2
C6
D2
CH-2 VoutC
R5
L2
Title
R12
Size
C3
R6
Number
R2
Revision
A4
D
Date:
File:
1
2
3
D
2014/09/12
C:\Users\..\AP3603do_140912.SchDoc
4
Sheet of
Drawn By :
5
6
Figure 12. Dual Output Step Up Application
■ Parts List
Parameter
Input capacitor
Symbol
C1
Output Capacitor
C2
Output Capacitor
C3
Bypass capacitor
Capacitor for V8
Capacitor for V8 Middle point
Capacitor for soft start
Phase Compensation Capacitor
Phase Compensation Capacitor
Current Sense Resistor
Current Sense Resistor
CH1 feedback resistor(H)
CH1 feedback resistor(L)
CH2 feedback resistor(H)
CH2 feedback resistor(L)
Frequency setting resistor
CH1 phase compensation resistor
CH1 phase compensation resistor
CH2 phase compensation resistor
CH2 phase compensation resistor
Catcher diode
Power inductor
N-channel MOSFET
C4
C5
C6
C7
C8
C9
R1
R2
R3
R4
R5
R6
R7
R8
R9
R10
R11
D1,D2
L1,L2
M1,M2
(Vin=6.4V~12V、Vout=12V、Io=17A、f=400kHz)
Condition
10uF×10parallel
330uF/16V×4parallel
10uF/25V(MLCC)x2parallel
330uF/16V×4parallel
10uF/25V(MLCC)x2parallel
0.1uF
2.2uF
0.22uF
0.1uF
6800pF
6800pF
2mΩ
2mΩ
110kΩ
47kΩ
110kΩ
47kΩ
75kΩ
4.7kΩ
47kΩ
4.7kΩ
47kΩ
40V30A
2.2uH
40V100A
015000004-E-02
2015/07
- 14 -
[AP3603]
■ Recommended External Circuit of Dual Phase Single Output
1
2
3
4
5
6
Vin
R1
A
C1
A
L1
R7
R9
R8
B
C8
C7
C9
C
R10
R11
FSYN
RSP1
RT
RSN1
FB1
DRV1
CC1
GND2
GND1
VDD
SS
V8
CC2
V4
FB2
DRV2
PWON
RSN2
MDC
RSP2
D1
Vout
R3
M1
C2
B
C4
R4
C5
M2
C6
D2
C
PWON
L2
Title
R12
Size
Number
R2
Revision
A4
D
Date:
File:
1
2
3
D
2014/09/12
C:\Users\..\AP3603_140912.SchDoc
4
Sheet of
Drawn By :
5
6
Figure 13. Dual Phase Step-Up Application
■ Parts List
Parameter
Input Capacitor
Output Capacitor
Bypass capacitor
Capacitor for V8
Capacitor for V8 Middle point
Soft Start Capacitor
Capacitor for phase compensation
Current Sense Resistor
Current Sense Resistor
Feedback resistor(H)
Feedback resistor(L)
Frequency setting resistor
Phase Compensation Resistor
Phase Compensation Resistor
Catcher diode
Power inductance
N-channel MOSFET
(Vin=6.4~12V、Vout=12V、Iout=34A、f=400kHz)
Symbol
Conditions
10uF×10parallel
C1
330uF/16V×4parallel
C2
10uF/25V(Ceramic)x2parallel
0.1uF
C4
2.2uF
C5
0.22uF
C6
0.1uF
C7
6800pF
C8
2mΩ
R1
2mΩ
R2
110kΩ
R3
47kΩ
R4
150kΩ
R7
4.7kΩ
R8
47kΩ
R9
40V30A
D1,D2
3.3uH
L1,L2
40V50A
M1,M2
015000004-E-02
2015/07
- 15 -
[AP3603]
16. Package
■ Outline Dimensions
・20-pin HTSSOP (Unit : mm)
■ Marking
AP3603
XXXXXXX
(2)
(3)
(1)
1pin Indication
(2)
Product No.
(3)
Date Code (7digits)
(1)
015000004-E-02
2015/07
- 16 -
[AP3603]
17. Revise History
Date
(YY/MM/DD)
15/02/09
15/03/12
15/07/30
Revision
Page
00
01
8
02
1
3
9
11
Contents
First edition
Add 10.7 Quasi-Foldback Over Current Protection (PWM operation)
2.Features; Correction of the explanation of input voltage
5. Ordering Guide; Correction of the explanation of ordering number,
Correction of the explanation of 10.9 external synchronous operation
12. Application Information; Correction of the explanation of 12.1 output
voltage setting.
015000004-E-02
2015/07
- 17 -
[AP3603]
IMPORTANT NOTICE
0. Asahi Kasei Microdevices Corporation (“AKM”) reserves the right to make changes to the information
contained in this document without notice. When you consider any use or application of AKM product
stipulated in this document (“Product”), please make inquiries the sales office of AKM or authorized
distributors as to current status of the Products.
1. All information included in this document are provided only to illustrate the operation and application
examples of AKM Products. AKM neither makes warranties or representations with respect to the
accuracy or completeness of the information contained in this document nor grants any license to any
intellectual property rights or any other rights of AKM or any third party with respect to the information
in this document. You are fully responsible for use of such information contained in this document in
your product design or applications. AKM ASSUMES NO LIABILITY FOR ANY LOSSES
INCURRED BY YOU OR THIRD PARTIES ARISING FROM THE USE OF SUCH INFORMATION
IN YOUR PRODUCT DESIGN OR APPLICATIONS.
2. The Product is neither intended nor warranted for use in equipment or systems that require
extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may
cause loss of human life, bodily injury, serious property damage or serious public impact, including but
not limited to, equipment used in nuclear facilities, equipment used in the aerospace industry, medical
equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling
equipment, equipment used to control combustions or explosions, safety devices, elevators and
escalators, devices related to electric power, and equipment used in finance-related fields. Do not use
Product for the above use unless specifically agreed by AKM in writing.
3. Though AKM works continually to improve the Product’s quality and reliability, you are responsible for
complying with safety standards and for providing adequate designs and safeguards for your hardware,
software and systems which minimize risk and avoid situations in which a malfunction or failure of the
Product could cause loss of human life, bodily injury or damage to property, including data loss or
corruption.
4. Do not use or otherwise make available the Product or related technology or any information contained
in this document for any military purposes, including without limitation, for the design, development,
use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology
products (mass destruction weapons). When exporting the Products or related technology or any
information contained in this document, you should comply with the applicable export control laws and
regulations and follow the procedures required by such laws and regulations. The Products and related
technology may not be used for or incorporated into any products or systems whose manufacture, use,
or sale is prohibited under any applicable domestic or foreign laws or regulations.
5. Please contact AKM sales representative for details as to environmental matters such as the RoHS
compatibility of the Product. Please use the Product in compliance with all applicable laws and
regulations that regulate the inclusion or use of controlled substances, including without limitation, the
EU RoHS Directive. AKM assumes no liability for damages or losses occurring as a result of
noncompliance with applicable laws and regulations.
6. Resale of the Product with provisions different from the statement and/or technical features set forth in
this document shall immediately void any warranty granted by AKM for the Product and shall not create
or extend in any manner whatsoever, any liability of AKM.
7. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior
written consent of AKM.
015000004-E-02
2015/07
- 18 -