S ER IES 8 8 SUPERFLY ® ULTRAMINIATURE CONNECTORS AND CORDSETS APRIL 2015 Cover Photo Credit: US Army. SPC Rebecca Buck THE ULTIMATE NANOMINIATURE TACTICAL CONNECTOR Quick-Disconnect (QDC) and threaded coupling cable connectors with pigtail wires, rugged overmolding, polyurethane jacketing or nylon overbraid Quick-Disconnect (QDC) and threaded coupling panel mounted connectors with pigtail wires, PCB or solder cup terminations Ready for the toughest, smallest, and highest speed applications you’ve got. G lenair Series 88 SuperFly® represents a perfect storm of high-performance contacts, shells, wires, termination and mating technologies. SuperFly® is the only connector series in existence that combines the weightsaving and performance advantages of nanominiature, microminiature and AS39029 type (size #23) contacts in a hybrid package for battlefield communications, computing, and other high-performance applications. Available in factory-terminated cordsets, single-ended pigtails, and PCB termination receptacles for complete flexibility in cable and box configurations. QDC and threaded SuperFly® cordsets can ship with a variety of cabling options, including ultraflexible GhostWire or impedance-controlled twisted pairs for high-speed applications. Glenair, Inc. 1211 Air Way Glendale, CA 91201-2497 818-247-6000 [email protected] www.glenair.com SERIES 88 SuperFly® Connectors Table of Contents General Information and Reference Series 880 Quick-Disconnect Connectors Series 88 SuperFly® Introduction................................................ A-2 Performance Specifications and Materials.............................. A-3 Materials, Finishes and Cable Jacket/Overbraid................... A-4 Shrouded and Unshrouded Contacts, Modification Codes and Application Note ........................ A-5 Insert Arrangements and Layouts Organized by Protocol ............................................. A-6 MIL-STD-681 Color Code Chart................................................... A-8 Vertical PCB Footprints................................................................... A-9 Right Angle PCB Footprints........................................................A-17 A Product Selection Guide.................................................................B-1 Series 880 QDC Introduction........................................................B-2 Pigtail Wire Connectors...................................................................B-4 PCB Connectors.............................................................................. B-16 Solder Cup Connectors................................................................ B-28 B Series 881 Threaded Coupling Connectors Product Selection Guide................................................................ C-1 Series 881 Threaded Coupling Introduction.......................... C-2 Pigtail Wire Connectors.................................................................. C-4 PCB Connectors..............................................................................C-12 Solder Cup Connectors................................................................C-16 C Series 886 Single-Ended and Back-to-Back Cordsets Product Selection Guide................................................................D-1 Series 886 Cordset Introduction.................................................D-2 Quick Disconnect Cordsets Single-Ended.....................................................................................D-4 Back-to-Back.......................................................................................D-8 Threaded Coupling Cordsets Single-Ended...................................................................................D-10 Back-to-Back.....................................................................................D-14 Low Profile “Cobra” Equipped Cordsets............................D-16 D Connector Accessories and Tools Product Selection Guide.................................................................E-1 Accessories..........................................................................................E-2 Tools.................................................................................................... E-14 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. E 1 SERIES 88 SuperFly® Connectors Introduction ® A Series 88 SuperFly : the ultimate nanominiature tactical connector Ready for the toughest, smallest, and highest-speed applications you’ve got Compact, ultralightweight SuperFly® connectors feature threaded or push-pull coupling, EMI shielding and IP67 ingress protection. Available in a variety of layouts and sizes for audio, video, communications and data applications, Series 88 connectors are ideal for man-portable electronics where size and weight are prime considerations. Available in ready-to-use cordsets and single-ended pigtails, Series 88 SuperFly® QDC and threaded SuperFly cordsets can ship with a variety of cabling options, including ultraflexible GhostWire or impedancecontrolled twisted pairs for high-speed applications. IP67 immersion rated High-reliability contacts: 5 Amp, 3 Amp, and 1 Amp High shock and vibration Robust EMI shielding Designed for high speed data applications Pre-wired, epoxy-sealed cordsets Straight and 90° PC tail receptacles 27 Contact arrangements Front or rear panel mounting Aluminum or stainless steel Accepts #22 to #32 AWG wire Made-to-order multi-branch cables and assemblies 5 Amp Socket Contact Band-Master Shield Termination Adapter 1 Amp Pin Contact Rear-panel mount push-pull and threaded PCB receptacles, and AlphaLink flex jumpers now available SUPPORTED CONTACTS #23 AS39029 Type 5 Amp Crimp Contact Micro 3 Amp TwistPin Contact Nano 1 Amp TwistPin Contact SuperFly® front and rear box panel mount receptacles 3 Amp Socket Contact 1 Amp Socket Contact 5 Amp Pin Contact 3 Amp Pin Contact Gold-plated Springs Epoxy Epoxy Jam Nut Series 880 QDC Plug 2 O-rings Band-Master Shield Termination Adapter Series 880 QDC Receptacle © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 88 SuperFly® Connectors Performance Specifications and Materials NOW AVAILABLE: PRINTED CIRCUIT BOARD PLUGS AND RECEPTACLES Quick-Disconnect Threaded A Right Angle, Rear Panel Mount Right Angle, Rear Panel Mount, PCB Mounting Holes Vertical, Rear Panel Mount Vertical, Rear Panel Mount, PCB Mounting Holes Vertical, Rear Panel Mount, Ground Pins Vertical, Rear Panel Mount Vertical, Rear Panel Mount Right Angle, Rear Panel Mount Mechanical and Environmental Specifications Description Water Immersion, mated Ingress Protection, mated Vibration, Sine Requirement 1 meter, 1 hour IP67 rating 30 g's Vibration, Random 37.8 g's Gunfire Vibration No discontinuity Mechanical Shock 300g's Corrosion (Salt Mist) Fluid Immersion Magnetic Permeability Durability (mating cycles) Nickel-plated aluminum: 48 hours Other finishes: 500 hours No damage from immersion in various fuels and oils. 2 μ maximum. 2000 Standard MIL-STD-810F Method 512.4 IEC-60529 EIA-364-28 EIA-364-28 Test Condition V IEC-60512-6-4 MIL-STD-810 Method 519 EIA-364-27 Condition D IEC-60512-6-3 EIA-364-26 IEC 60512-11-6 EIA-364-10 EIA-364-54 EIA-364-09 Electrical Specifications Property Current Rating Wire Size Dielectric Withstanding Voltage Contact Resistance Contact Specification Shell Resistance Shielding Effectiveness Insulation Resistance 5 Amp Contact 5A #22 - #28 AWG 500Vac 20 milliohms AS39029 3 Amp Contact 3A #24 - #30 AWG 600Vac 32 milliohms MIL-DTL-83513 < 5 milliohms >55 dB thru 1000MHz 5000 megohms minimum 1 Amp Contact 1A #28 - #32 AWG 250Vac 80 milliohms MIL-DTL-32139 Materials Property Insulator Shell 1A. Contact 3A. and 5A. Contact Encapsulant Wire Description Thermoplastic, glass-filled Aluminum or stainless steel Precious metal alloy pin, gold-plated copper alloy socket Copper alloy, 50 microinches gold over nickel finish Epoxy Space-Grade High strength silver-coated copper alloy, ETFE insulation (M22759/33 or equiv.) © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 3 SERIES 88 SuperFly® Connectors Materials, Finishes and Cable Jacket/Overbraid ABOUT SUPERFLY® MATERIALS AND FINISHES Four standard material and finish options are available. A 1 Aluminum shell with Electroless Nickel (EN). High reflectivity and poor corrosion resistance make nickel a poor choice for tactical systems, but nickel is preferred for avionics systems, space vehicles, medical equipment and test gear where corrosion is not a primary concern. Nickel is highly conductive and is excellent for EMI-protected systems. 4 Aluminum shell with Olive Drab or Cadmium (OD over Cad). very good, corrosion resistance and excellent conductivity. Non-reflective OD over Cad is a primary choice for any harsh environment. Inherently lubricious, resists galling. 2 Aluminum shell with Black Zinc-Nickel (Zn-Ni). Although less conductive than other finishes, non-reflective black Zn-Ni is a typical choice for soldier gear. Corrosion resistance is very good. 5 6 3 Aluminum shell with Electroless Nickel-PTFE (EN-PTFE). Excellent durability, corrosion resistance and conductivity. Nonreflective EN-PTFE is a primary choice for any harsh environment. Inherently lubricious, resists galling. 7 Stainless steel shell with Zinc-Cobalt (ZN-CO). Excellent durability, corrosion resistance and conductivity. Non-reflective black finish is an excellent choice for any harsh environment. Stainless steel, passivated finish. Excellent corrosion resistance, good conductivity. A good choice for high corrosion areas where EMI shielding is not a primary concern. Suitable for most aerospace and tactical gear. Stainless steel, Ni-PTFE finish. Excellent corrosion resistance and excellent conductivity. A good choice for high corrosion areas where EMI shielding is a primary concern. Highly conductive, non-reflective Ni-PTFE finish is suitable for all aerospace and tactical systems. Material and Finish Comparison Data Property 1 2 3 4 5 6 7 Material and Finish Aluminum Electroless Nickel Aluminum Black ZincNickel Aluminum Electoless NickelPTFE Aluminum Olive Drab over Cadmium Stainless Steel Black ZincCobalt Stainless Steel Passivated Stainless Steel Electroless Nickel-PTFE Glenair Code M ZR MT1 NF ZC ZK ZMT Poor Good Very Good Very Good Excellent Excellent Excellent Yes Excellent Reflective $ Yes Good Non-reflective $$ Yes Excellent Non-reflective $$ No Excellent Non-reflective $$ No Excellent Non-reflective $$$$ Yes Good Reflective $$$$ Yes Excellent Non-reflective $$$$ Corrosion Resistance RoHS Compliance1 Conductivity Reflectivity Cost 1. Meets DoD directives and European regulations for elimination of cadmium and hexavalent chromate. ABOUT SUPERFLY® CABLE JACKETS Standard SuperFly® cable jacket/overbraid include: extruded thermoplastic polyurethane (TPU) and nylon overbraid. TPU offers excellent all-round performance and is typically specified for military gear and oil exploration equipment. Low-toxicity TPU is non-halogenated and flame-retardent. Braided nylon jackets offer outstanding flexibility. For soldier systems applications, braided jackets are an alternative to TPU jackets if weight and flexibility outweigh the drawbacks of braid; e.g.the possibility of snagging the braid or entrapping contamination. Outer Jacket/Braid Comparison Data Property Flammability UL 94V-0 Temperature Range Flexibility Solvent Resistance Abrasion Resistance Toxicity TPU Jacket Flame-Retardent Yes -45°C to +150°C Good Excellent Excellent Low Smoke, Zero Halogen Nylon Braid Flame-Retardent No -50°C to +150°C Excellent Good Very Good Zero Halogen Additional jacket and overmold materials are available for custom cordsets. Contact the factory for more information. 4 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 88 SuperFly® Connectors Shrouded and Unshrouded Contacts, Modification Codes and Application Notes ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the Insert. Unshrouded contacts extend from the insert face. Figure 1 shows a shrouded insert, and figure 2 illustrates an unshrouded insert. Shrouded inserts contain 1 amp and 3 amp pin contacts along with 5 amp socket contact. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp twistpins. 3 Amp Micro Twistpin 3 Amp Micro Socket 1 Amp Nano Twistpin 1 Amp Nano Socket 5 Amp #23 Socket Figure 1 5 Amp #23 Pin Figure 2 Shrouded Type B Insert Unshrouded Type A Insert MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors feature a single key and keyway for shell polarization. Optional alternate key positions are available for situations where multiple connectors are used. Add the suffix code shown below to the part number. Example: 880-003RA-E3W-M200J5-24-686A. Alternate Key Positions Key Position A B C D E F Suffix Code 686A 686B 686C 686D 686E 686F A° B° 150° 75° 95° 140° 75° 95° 210° 210° 230° 275° 275° 210° Master Key Master Key A° B° B° A° Plug Key Positions Receptacle Key Positions MOD-518 OPEN FACE SEALING Standard SuperFly® connectors meet IP67 when mated. If water immersion is a requirement for open face (unmated) connectors, the connector should be specially processed and tested. Modification code 518 specifies special processing and 100% leak testing. Connectors are 100% tested to meet a leak rate of 1 x 10-4 cc/second of helium at 1 atmosphere pressure differential. Add suffix code -518 to the part number to call out open face sealing. Example: 880-004RA-G6M10N-M035J-24-518 APPLICATION NOTE: SAND AND DUST EXPOSURE Unmated SuperFly® connectors should not be exposed to sand, dust or debris, which can be entrapped in the small contact cavities. Debris entrapment can cause excessive contact wear and possible failure. Unmated connectors should be fitted with dust caps or protective covers. © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 5 A SERIES 88 SuperFly® Connectors Insert Arrangements Layouts viewed from mating face of shrouded (Type B) insert. Use mirror image for unshrouded (Type A) insert. Arrangements with 5 Amp (#22-28 AWG) Contacts A 1 1 Contact Size 2 Contact Arrangement No. of Contacts Current Rating Contact Size Wire Size (AWG) DWV Voltage (VAC Sea Level) 3 3 4 2 3 5 3 5 Amp 1 2 1 2 5 6 4 8 7 6 9 7 10 E3W 3 5A. #23 #22–#28 F4W 4 5A. #23 #22–#28 G7W 7 5A. #23 #22–#28 H10W 10 5A. #23 #22–#28 500 500 500 500 Arrangements with 5 Amp (#22-#28 AWG) and 1 Amp (#30-32 AWG) Contacts Contact Size 2 2 1 4 1 3 5 Amp 3 3 4 4 7 D2W2N 1 8 6 F4W4N 2 5A. #23 #22–#28 2 1A. Nano #28–#32 4 5A. #23 #22–#28 4 1A. Nano #28–#32 500 250 500 250 3 5 2 1 Amp Contact Arrangement No. of Contacts Current Rating Contact Size Wire Size (AWG) DWV Voltage (VAC Sea Level) 5 7 8 9 10 11 12 13 14 15 16 17 18 19 20 2 6 500 5 6 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 1 H6W14N 6 14 5A. 1A. #23 Nano #22–#28 #28–#32 4 7 J7W19N 250 7 5A. #23 #22–#28 19 1A. Nano #28–#32 500 250 Arrangements with 3 Amp (#24-30 AWG) Contacts 1 Contact Size 3 Amp Contact Arrangement No. of Contacts Current Rating Contact Size Wire Size (AWG) DWV Voltage (VAC Sea Level) 6 1 5 3 3 2 3 4 1 2 1 2 7 6 4 3 5 6 8 9 7 10 1 3 1 2 7 4 12 8 13 16 19 17 4 5 9 13 10 14 18 19 22 D3M 3 3A. Micro #24–#30 E4M 4 3A. Micro #24–#30 F7M 7 3A. Micro #24–#30 G10M 10 3A. Micro #24–#30 K19M 19 3A. Micro #24–#30 L22M 22 3A. Micro #24–#30 600 600 600 600 600 600 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 88 SuperFly® Connectors Insert Arrangements and Layouts Organized by Protocol Layouts viewed from mating face of shrouded (Type B) insert. Use mirror image for unshrouded (Type A) insert. Arrangements with 3 Amp (#24-#30 Awg) and 1 Amp (#30-32 AWG) Contacts Contact Size 2 1 1 Amp 3 4 3 7 C2M2N 2 2 3A. 1A. Micro Nano #24–#30 #28–#32 600 2 1 6 4 1 3 Amp Contact Arrangement No. of Contacts Current Rating Contact Size Wire Size (AWG) DWV Voltage (VAC Sea Level) 5 2 6 8 8 11 5 12 4 3 3 2 4 7 10 5 7 8 9 10 11 12 1 2 6 5 11 16 8 13 18 10 15 7 12 17 9 14 1 16 13 14 15 1 13 4 3 6 12 2 11 10 9 A 3 4 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 5 6 7 8 E4M4N F4M8N G6M10N G6M12N K13M19N 4 4 4 8 6 10 6 12 13 19 3A. 1A. 3A. 1A. 3A. 1A. 3A. 1A. 3A. 1A. Micro Nano Micro Nano Micro Nano Micro Nano Micro Nano #24–#30 #28–#32 #24–#30 #28–#32 #24–#30 #28–#32 #24–#30 #28–#32 #24–#30 #28–#32 250 600 250 600 250 600 250 600 250 600 250 Arrangements with 1 Amp Contacts (#28 - #32 AWG) Contact Size 1 Amp Contact Arrangement No. of Contacts Current Rating Contact Size Wire Size (AWG) DWV Voltage (VAC Sea Level) 1 2 6 7 5 3 3 1 4 2 6 5 8 9 7 10 4 1 3 7 8 12 13 17 19 16 75 10 4 1 9 13 18 22 14 19 3 8 14 19 25 1 30 2 7 13 18 24 29 31 5 10 16 23 29 1 4 37 34 9 15 22 28 33 1 6 12 19 27 34 40 5 11 18 26 33 39 44 B7N 7 1A. Nano #28–#32 C10N 10 1A. Nano #28–#32 E19N 19 1A. Nano #28–#32 F22N 22 1A. Nano #28–#32 G31N 31 1A. Nano #28–#32 H37N 37 1A. Nano #28–#32 J44N 44 1A. Nano #28–#32 250 250 250 250 250 250 250 LAYOUTS ORGANIZED BY PROTOCOL The geometries of SuperFly® nano and micro contact cavities were designed to offer the best possible differential impedance match for a contact pair. This makes SuperFly® a great choice for high speed applications. The following table is provided as a starting-point when selecting a layout for your high speed application. The suggested layouts contain the minimum number of contacts required for the specified protocol. Please contact the Glenair factory for more information including other supported protocols and high speed test data. High Speed Applications Data Pair Contact Size Suggested Layouts 10/100 Ethernet Nano Micro Size 23 B7N G10M G7W GHz Protocol MHz Frequency Gigabit Ethernet Nano Micro Size 23 C10N G10M H10W USB 2.0 HDMI/DVI Display Port USB 3.0 eSATA/SATA Nano Micro Nano Micro Nano Micro Nano Micro Nano Micro C2M2N D2W2N E19N K19M F22N L22M C10N G10M C10N G10M © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 7 SERIES 88 SuperFly MIL-STD-681 Color Code Chart MIL-STD-681 Color Code Chart for Micro-D Connectors A 8 PIN NO. MIL-STD-681 NO NUMBER Base Color 1 0 2 1 3 2 4 3 5 4 YEL 6 5 GRN 7 6 8 9 First Stripe Second Stripe PIN NO. MIL-STD-681 NUMBER. Base Color First Stripe Second Stripe Third Stripe BLK 51 957 WHT GRN VIO BRN 52 958 WHT GRN GRY RED 53 967 WHT BLU VIO ORN 54 968 WHT BLU GRY 55 978 WHT VIO GRY 56 9012 WHT BLK BRN RED BLU 57 9013 WHT BLK BRN ORN 7 VIO 58 9014 WHT BLK BRN YEL 8 GRY 59 9015 WHT BLK BRN GRN BLU 10 9 WHT 60 9016 WHT BLK BRN 11 90 WHT BLK 61 9017 WHT BLK BRN VIO 12 91 WHT BRN 62 9018 WHT BLK BRN GRY 13 92 WHT RED 63 9023 WHT BLK RED ORN 14 93 WHT ORN 64 9024 WHT BLK RED YEL 15 94 WHT YEL 65 9025 WHT BLK RED GRN BLU 16 95 WHT GRN 66 9026 WHT BLK RED 17 96 WHT BLU 67 9027 WHT BLK RED VIO 18 97 WHT VIO 68 9028 WHT BLK RED GRY 19 98 WHT GRY 20 901 WHT BLK 69 9034 WHT BLK ORN YEL BRN 70 9035 WHT BLK ORN GRN BLU 21 902 WHT BLK RED 71 9036 WHT BLK ORN 22 903 WHT BLK ORN 72 9037 WHT BLK ORN VIO 23 904 WHT BLK YEL 73 9038 WHT BLK ORN GRY 24 905 WHT BLK GRN 74 9045 WHT BLK YEL GRN 25 906 WHT BLK BLU 75 9046 WHT BLK YEL BLU 26 907 WHT BLK VIO 76 9047 WHT BLK YEL VIO 27 908 WHT BLK GRY 77 9048 WHT BLK YEL GRY BLU 28 912 WHT BRN RED 78 9056 WHT BLK GRN 29 913 WHT BRN ORN 79 9057 WHT BLK GRN VIO 30 914 WHT BRN YEL 80 9058 WHT BLK GRN GRY 31 915 WHT BRN GRN 81 9067 WHT BLK BLU VIO 32 916 WHT BRN BLU 82 9068 WHT BLK BLU GRY 33 917 WHT BRN VIO 83 9078 WHT BLK VIO GRY 34 918 WHT BRN GRY 84 9123 WHT BRN RED ORN 35 923 WHT RED ORN 85 9124 WHT BRN RED YEL 36 924 WHT RED YEL 86 9125 WHT BRN RED GRN BLU 37 925 WHT RED GRN 87 9126 WHT BRN RED 38 926 WHT RED BLU 88 9127 WHT BRN RED VIO 39 927 WHT RED VIO 89 9128 WHT BRN RED GRY 40 928 WHT RED GRY 90 9134 WHT BRN ORN YEL 41 934 WHT ORN YEL 91 9135 WHT BRN ORN GRN BLU 42 935 WHT ORN GRN 92 9136 WHT BRN ORN 43 936 WHT ORN BLU 93 9137 WHT BRN ORN VIO 44 937 WHT ORN VIO 94 9138 WHT BRN ORN GRY 45 938 WHT ORN GRY 95 9145 WHT BRN YEL GRN 46 945 WHT YEL GRN 96 9146 WHT BRN YEL BLU 47 946 WHT YEL BLU 97 9147 WHT BRN YEL VIO 48 947 WHT YEL VIO 98 9148 WHT BRN YEL GRY 49 948 WHT YEL GRY 99 9156 WHT BRN GRN BLU 50 956 WHT GRN BLU 100 9157 WHT BRN GRN VIO © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 88 SuperFly® Connectors Vertical PCB Footprints Viewed from rear PC tail side of unshrouded (Type A) insert. Use mirror image for shrouded (Type B) insert. PC Tail Wire Diameter By Contact Size #23 contact uses #24 wire Ø.020 Insert Arrangement PCB Footprint 4x 90° 1 2 4 5 6 7 3 0 Ø.281 (7.14) Ø.332 (8.43) Ø.412 (10.46) 4x .080 (2.03) 4x Standoff 0 C10N 1 4 3 2 4x 90° 5 7 8 6 9 Ø.412 (10.46) 4X .080 (2.03) 4X STANDOFF C2M2N Tag X Loc Y Loc 6 -.0500-.0250 7 .0000-.0250 8 .0500-.0250 9 -.0250-.0683 10 .0250-.0683 1 2 Tag X Loc Y Loc Size 1 -.0250.0550Nano 2 .0250.0550Nano Tag X Loc Y Loc Size 3 -.0325-.0280 Micro 4 .0325-.0280 Micro 4X 90° 4 3 Ø.301 (7.65) Ø.352 (8.94) 45° X 0 Tag X Loc Y Loc Size 1 .0000.0373Micro 2 -.0325-.0190 Micro 3 .0325-.0190 Micro Ø.431 (10.95) 4x .080 (2.03) 4x Standoff Y D3M 0 4x 90° 1 2 3 Ø.320 (8.13) Ø.371 (9.42) 45° X 0 Ø.431 (10.95) 4X .080 4X STANDOFF Y D2W2N Tag X Loc Y Loc Size 1 -.0375.0222 #23 2 .0375.0222 #23 Tag X Loc Y Loc Size 3 -.0250-.0544 Nano 4 .0250-.0544 Nano 4X 90° 1 0 Size Nano Nano Nano Nano Nano 45° X 0 0 Tag X Loc Y Loc Size 1 -.0250.0683Nano 2 .0250.0683Nano 3 -.0500.0250Nano 4 .0000.0250Nano 5 .0500.0250Nano 10 Ø.301 (7.64) Ø.352 (8.94) Y A 45° X 0 Y Tag X Loc Y Loc Size 1 -.0250 .0433 Nano 2 .0250 .0433 Nano 3 -.0500.0000Nano 4 .0000 .0000 Nano 5 .0500 .0000 Nano 6 -.0250 -.0433 Nano 7 .0250 -.0433 Nano Ø.392 (9.96) Y Nano contact uses #30 wire Ø.010 Contact Location 4x .080 (2.03) 4x Standoff B7N Micro contact uses #26 wire Ø.016 2 3 4 Ø.320 (8.13) Ø.371 (9.42) 0 45° X © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 9 SERIES 88 SuperFly® Connectors Vertical PCB Footprints Viewed from rear PC tail side of unshrouded (Type A) insert. Use mirror image for shrouded (Type B) insert. PC Tail Wire Diameter By Contact Size Insert Arrangement A #23 contact uses #24 wire Ø.020 PCB Footprint Micro contact uses #26 wire Ø.016 Contact Location Tag X Loc Y Loc Size 1 .0000.0420 #23 2 -.0375-.0230 #23 3 .0375-.0230 #23 Ø.451 (11.46) 4x .080 (2.03) 4x Standoff Y E3W 4x 90° 1 0 2 Nano contact uses #30 wire Ø.010 3 Ø.340 (8.64) Ø.391 (9.93) 45° X 0 Tag X Loc Y Loc Size 1 -.0325 .0325 Micro 2 .0325.0325Micro 3 -.0325-.0325 Micro 4 .0325-.0325 Micro Ø.451 (11.46) 4X .080 (2.03) 4X STANDOFF Y 0 E4M 1 2 3 4 4X 90° Ø.340 (8.64) Ø.391 (9.93) 45° X 0 Ø.451 (11.46) 4X .080 (2.03) 4X STANDOFF Y 0 E19N Ø.340 (8.64) Ø.391 (9.93) 1 23 4 5 6 7 8 9 10 11 12 4X 90° 13 14 15 16 17 18 19 45° X 0 Ø.451 (11.46) 4x .080 (2.03) 4x Standoff 2 Y E4M4N 0 3 5 1 4x 90° 4 Tag X Loc Y Loc Size 1 -.0500 .0866 Nano 2 .0000 .0866 Nano 3 .0500 .0866 Nano 4 -.0750 .0433 Nano 5 -.0250.0433Nano 6 .0250.0433Nano 7 .0750 .0433 Nano 8 -.1000 .0000 Nano 9 -.0500 .0000 Nano 10.0000.0000Nano Tag X Loc Y Loc Size 11 .0500 .0000 Nano 12.1000.0000Nano 13-.0750-.0433 Nano 14-.0250-.0433 Nano 15 .0250-.0433 Nano 16 .0750-.0433 Nano 17-.0500-.0866 Nano 18 .0000-.0866 Nano 19 .0500-.0866 Nano Tag X Loc Y Loc Size 1 -.0650 .0000 Micro 2 -.0325.0719Micro 3 .0325 .0719 Micro 4 .0650.0000Micro Tag X Loc Y Loc Size 5 .0000.0156Nano 6 .0000-.0344 Nano 7 -.0250-.077 Nano 8 .0250-.077 Nano 6 8 7 Ø.340 (8.64) Ø.391 (9.93) 0 10 45° X © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 88 SuperFly® Connectors Vertical PCB Footprints Viewed from rear PC tail side of unshrouded (Type A) insert. Use mirror image for shrouded (Type B) insert. PC Tail Wire Diameter By Contact Size #23 contact uses #24 wire Ø.020 Insert Arrangement PCB Footprint Micro contact uses #26 wire Ø.016 Contact Location Tag X Loc Y Loc Size 1 -.0375.0375 #23 2 .0375.0375 #23 3 -.0375-.0375 #23 4 .0375-.0375 #23 Ø.471 (11.96) 4X .080 (2.03) 4X STANDOFF Y F4W 4X 90° 12 0 3 Nano contact uses #30 wire Ø.010 A 4 Ø.360 (9.14) Ø.411 (10.44) 45° X 0 Tag X Loc Y Loc Size 1 -.0325.0563Micro 2 .0325.0563Micro 3 -.0650.0000Micro 4 .0000.0000Micro 5 .0650.0000Micro 6 -.0325-.0563 Micro 7 .0325-.0563 Micro Ø.471 (11.96) 4x .080 (2.03) 4x Standoff Y F7M 0 4x 90° 2 1 3 4 5 6 7 Ø.360 (9.14) Ø.411 (10.44) 45° X 0 Ø.471 (11.96) 4X .080 (2.03) 4X STANDOFF Y F22N 0 2 3 4 1 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 4X 90° Ø.360 (9.14) Ø.411 (10.44) 45° X 0 Ø.471 (11.96) 4x .080 (2.03) 4x Standoff Y F4M8N 0 2 3 5 1 8 4x 90° 4 6 7 9 10 11 12 Ø.360 (9.14) Ø.411 (10.44) 0 Tag X Loc Y Loc Size 1 -.0750.0866Nano 2 -.0250.0866Nano 3 .0250.0866Nano 4 .0750.0866Nano 5 -.1000.0433Nano 6 -.0500.0433Nano 7 .0000.0433Nano 8 .0500.0433Nano 9 .1000.0433Nano 10-.0750 .0000 Nano 11-.0250 .0000 Nano Tag X Loc Y Loc Size 12.0250.0000Nano 13.0750.0000Nano 14-.1000-.0433 Nano 15-.0500-.0433 Nano 16 .0000-.0433 Nano 17 .0500-.0433 Nano 18 .1000-.0433 Nano 19-.0750-.0866 Nano 20-.0250-.0866 Nano 21 .0250-.0866 Nano 22 .0750-.0866 Nano Tag X Loc Y Loc Size 1 -.0813.0162Micro 2 -.0325.0833Micro 3 .0325.0833Micro 4 .0813.0162Micro Tag X Loc Y Loc Size 5 .0000.0270Nano 6 -.0250-.0163 Nano 7 .0250-.0163 Nano 8 -.0500-.0596 Nano 9 .0000-.0596 Nano 10.0500.0596Nano 11-.0250-.1029 Nano 12 .0250-.1029 Nano 45° X © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 11 SERIES 88 SuperFly® Connectors Vertical PCB Footprints Viewed from rear PC tail side of unshrouded (Type A) insert. Use mirror image for shrouded (Type B) insert. PC Tail Wire Diameter By Contact Size Insert Arrangement A #23 contact uses #24 wire Ø.020 PCB Footprint Ø.471 (11.96) 4x Standoff F4W4N 3 2 4x 90° 5 0 1 Tag X Loc Y Loc Size 1 -.0740-.0125 #23 2 -.0375.0750 #23 3 .0375.0750 #23 4 .0740-.0125 #23 8 7 45° X 0 Tag X Loc Y Loc Size 1 -.0375.0650 #23 2 .0375.0650 #23 3 -.0750.0000 #23 4 .0000.0000 #23 5 .0750.0000 #23 6 -.0375-.0650 #23 7 .0375-.0650 #23 Ø.490 (12.45) 4x .080 (2.03) 4x Standoff 1 Y G7W 2 4 3 0 Tag X Loc Y Loc Size 5 .0000.0000Nano 6 .0000-.0500 Nano 7 -.0250-.0933 Nano 8 .0250-.0933 Nano 4 6 Ø.360 (9.14) Ø.411 Nano contact uses #30 wire Ø.010 Contact Location 4x .080 (2.03) Y Micro contact uses #26 wire Ø.016 5 4x 90° 7 6 Ø.379 (9.63) Ø.430 (10.92) 45° 0 X 4x Standoff Y G10M 0 Tag X Loc Y Loc Size 1 -.0375.1025Micro 2 .0375.1025Micro 3 -.0750.0375Micro 4 .0000.0375Micro 5 .0750.0375Micro 6 -.0750-.0375 Micro 7 .0000-.0375 Micro 8 .0750-.0375 Micro 9 -.0375-.1025 Micro 10 .0375-.1025 Micro Ø.490 (12.45) 4x .080 (2.03) 2 1 4 3 6 5 4x 90° 8 7 10 9 Ø.379 (9.63) Ø.430 (10.92) 45° X 0 Ø.490 (12.45) 4x .080 (2.03) 4x Standoff Y G31N 0 Ø.379 (9.63) Ø.430 (10.92) 2 1 4 5 6 7 8 9 10 11 12 13 14 15 16 1718 19 20 21 22 23 24 25 26 27 28 29 3 31 30 45° 0 12 X 4x 90° Tag X Loc Y Loc Size 1 -.0250.1299Nano 2 .0250.1299Nano 3 -.1000.0866Nano 4 -.0500.0866Nano 5 .0000.0866Nano 6 .0500.0866Nano 7 .1000.0866Nano 8 -.1250.0433Nano 9 -.0750.0433Nano 10-.0250 .0433 Nano 11.0250.0433Nano 12.0750.0433Nano 13.1250.0433Nano 14-.1000 .0000 Nano 15-.0500 .0000 Nano 16.0000.0000Nano Tag X Loc Y Loc Size 17.0500.0000Nano 18.1000.0000Nano 19-.1250-.0433 Nano 20-.0750-.0433 Nano 21-.0250-.0433 Nano 22 .0250-.0433 Nano 23 .0750-.0433 Nano 24 .1250-.0433 Nano 25-.1000-.0866 Nano 26-.0500-.0866 Nano 27 .0000-.0866 Nano 28 .0500-.0866 Nano 29 .1000-.0866 Nano 30-.0250-.1299 Nano 31 .0250-.1299 Nano © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 88 SuperFly® Connectors Vertical PCB Footprints Viewed from rear PC tail side of unshrouded (Type A) insert. Use mirror image for shrouded (Type B) insert. PC Tail Wire Diameter By Contact Size Insert Arrangement #23 contact uses #24 wire Ø.020 PCB Footprint Ø.490 (12.45) Y 2 0 G6M10N 4 3 1 10 9 11 6 4x 90° 12 Tag X Loc Y Loc Size 1 -.0900-.0214 Micro 2 -.0872.0583Micro 3 -.0325.1037Micro 4 .0325.1037Micro 5 .0872.0583Micro 6 .0900-.0214 Micro Tag X Loc Y Loc Size 7 -.0250.0350Nano 8 -.0250-.0350 Nano 9 -.0250-.0150 Nano 10 .0250-.0150 Nano 11-.0250-.0650 Nano 12 .0250-.0650 Nano 13-.0750-.1150 Nano 14-.0250-.1150 Nano 15 .0250-.1150 Nano 16 .0750-.1150 Nano Tag X Loc Y Loc Size 1 -.1035 -.0227 Micro 2 -.1006.0598Micro 3 -.0413.1171Micro 4 .0413.1171Micro 5 .1006.0598Micro 6 .1035-.0227 Micro Tag X Loc Y Loc Size 7 -.0500-.0716 Nano 8 -.0500.0150Nano 9 -.0250.1149Nano 10-.0250-.0283 Nano 11-.0250 .0583 Nano 12 .0000-.0716 Nano 13.0000.0150Nano 14 .0250-.1149 Nano 15 .0250-.0283 Nano 16.0250.0583Nano 17 .0500-.0716 Nano 18.0500.0150Nano Tag X Loc Y Loc Size 1 -.0375.1025 #23 2 .0375.1025 #23 3 -.0750.0375 #23 4 .0000.0375 #23 5 .0750.0375 #23 Tag X Loc Y Loc 6 -.0750-.0375 7 .0000-.0375 8 .0750-.0375 9 -.0375-.1025 10 .0375-.1025 15 16 13 14 Ø.379 (9.63) Ø.430 (10.92) 5 7 8 45° X 0 Ø.490 (12.45) 4x .080 (2.03) 4x Standoff Y 0 G6M12N 3 2 4 16 5 13 18 6 15 11 8 1 10 4x 90° 7 12 17 14 9 Ø.379 (9.63) Ø.430 (10.92) 45° 0 X Ø.530 (13.46) 4x .080 (2.03) 4x Standoff Y H10W 2 1 4 3 5 0 6 7 9 Nano contact uses #30 wire Ø.010 Contact Location 4x .080 (2.03) 4x Standoff Micro contact uses #26 wire Ø.016 A Size #23 #23 #23 #23 #23 4x 90° 8 10 Ø.419 (10.64) Ø.470 (11.94) 45° 0 X © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 13 SERIES 88 SuperFly® Connectors Vertical PCB Footprints Viewed from rear PC tail side of unshrouded (Type A) insert. Use mirror image for shrouded (Type B) insert. PC Tail Wire Diameter By Contact Size Insert Arrangement #23 contact uses #24 wire Ø.020 PCB Footprint Ø.530 (13.46) 4x .080 (2.03) Y H37N 0 1 2 3 4 5 6 7 89 10 11 12 13 14 15 1617 18 19 20 21 22 23 24 2526 27 28 29 30 31 32 33 34 35 36 37 Ø.419 (10.64) Ø.470 (11.94) 0 X 4x 90° 45° Ø.530 (13.46) 4x .080 (2.03) 4x Standoff Y H6W14N 0 Ø.419 (10.64) Ø.470 (11.94) 4 3 2 1 7 8 9 10 11 12 13 14 15 16 6 45° 0 14 5 17 18 19 20 X Nano contact uses #30 wire Ø.010 Contact Location A 4x Standoff Micro contact uses #26 wire Ø.016 4x 90° Tag X Loc Y Loc Size 1 -.0750.1299Nano 2 -.0250.1299Nano 3 .0250.1299Nano 4 .0750.1299Nano 5 -.1000.0866Nano 6 -.0500.0866Nano 7 .0000.0866Nano 8 .0500.0866Nano 9 .1000.0866Nano 10-.1250 .0433 Nano 11.-.0750 .0433 Nano 12-.0250 .0433 Nano 13.0250.0433Nano 14.0750.0433Nano 15.1250.0433Nano 16-.1500 .0000 Nano 17-.1000 .0000 Nano 18-.0500 .0000 Nano 19.0000.0000Nano Tag X Loc Y Loc Size 20.0500.0000Nano 21.1000.0000Nano 22.1500.0000Nano 23-.1250-.0433 Nano 24-.0750-.0433 Nano 25-.0250-.0433 Nano 26 .0250-.0433 Nano 27 .0750-.0433 Nano 28 .1250-.0433 Nano 29-.1000-.0866 Nano 30-.0500-.0866 Nano 31 .0000-.0866 Nano 32 .0500-.0866 Nano 33 .1000-.0866 Nano 34-.0750-.1299 Nano 35-.0250-.1299 Nano 36 .0250-.1299 Nano 37 .0750-.1299 Nano Tag X Loc Y Loc Size 1 -.1200 -.0500 #23 2 -.1200 .0500 #23 3 -.0500 .1200 #23 4 .0500 .1200 #23 5 .1200.0500 #23 6 .1200-.0500 #23 Tag X Loc Y Loc Size 7 -.0250.0388Nano 8 .0250.0388Nano 9 .0500-.0045 Nano 10 .0000-.0045 Nano 11 .0500-.0045 Nano 12-.0250-.0478 Nano 13 .0250-.0478 Nano 14-.0500-.0911 Nano 15 .0000-.0911 Nano 16 .0500-.0911 Nano 17-.0750-.1344 Nano 18-.0250-.1344 Nano 19 .0250-.1344 Nano 20 .0750-.1344 Nano © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 88 SuperFly® Connectors Vertical PCB Footprints Viewed from rear PC tail side of unshrouded (Type A) insert. Use mirror image for shrouded (Type B) insert. PC Tail Wire Diameter By Contact Size Insert Arrangement #23 contact uses #24 wire Ø.020 PCB Footprint Ø.569 (14.45) 4x Standoff J44N 0 1 2 3 4 5 6 7 8 910 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 4x 90° Ø.458 (11.63) Ø.509 (12.93) 45° 0 X Ø.569 (14.45) 4x .080 (2.03) 4x Standoff 3 Y J7W19N 2 0 Ø.458 (11.63) Ø.509 (12.93) 1 4 5 8 9 10 11 12 13 14 15 16 17 18 19 20 21 6 7 22 23 24 25 26 45° 0 X Nano contact uses #30 wire Ø.010 Contact Location 4x .080 (2.03) Y Micro contact uses #26 wire Ø.016 4x 90° Tag X Loc Y Loc Size 1 -.1000.1299Nano 2 -.0500.1299Nano 3 .0000.1299Nano 4 .0500.1299Nano 5 .1000.1299Nano 6 -.1250.0866Nano 7 -.0750.0866Nano 8 -.0250.0866Nano 9 .0250.0866Nano 10.0750.0866Nano 11.1250.0866Nano 12-.1500 .0433 Nano 13-.1000 .0433 Nano 14-.0500 .0433 Nano 15.0000.0433Nano 16.0500.0433Nano 17.1000.0433Nano 18.1500.0433Nano 19-.1750 .0000 Nano 20-.1250 .0000 Nano 21-.0750 .0000 Nano 22-.0250 .0000 Nano Tag X Loc Y Loc Size 23.0250.0000Nano 24.0750.0000Nano 25.1250.0000Nano 26.1750.0000Nano 27-.1500-.0433 Nano 28-.1000-.0433 Nano 29-.0500-.0433 Nano 30 .0000-.0433 Nano 31 .0500-.0433 Nano 32 .1000-.0433 Nano 33 .1500-.0433 Nano 34-.1250-.0866 Nano 35-.0750-.0866 Nano 36-.0250-.0866 Nano 37 .0250-.0866 Nano 38 .0750-.0866 Nano 39 .1250-.0866 Nano 40-.1000-.1299 Nano 41-.0500-.1299 Nano 42 .0000-.1299 Nano 43 .0500-.1299 Nano 44 .1000-.1299 Nano Tag X Loc Y Loc Size 1 -.1299-.0850 #23 2 -.1477.0160 #23 3 -.0964.1049 #23 4 .0000.1400 #23 5 .0964.1049 #23 6 .1477.0160 #23 7 .1299-.0850 #23 Tag X Loc Y Loc Size 8 -.0250.0613Nano 9 .0250.0613Nano 10-.0500 .0180 Nano 11.0000.0180Nano 12.0500.0180Nano 13-.0750-.0253 Nano 14-.0250-.0253 Nano 15 .0250-.0253 Nano 16 .0750-.0253 Nano 17-.0500-.0686 Nano 18 .0000-.0686 Nano 19 .0500-.0686 Nano 20-.0250-.1119 Nano 21 .0250-.1119 Nano 22-.1000-.1552 Nano 23-.0500-.1552 Nano 24 .0000-.1552 Nano 25 .0500-.1552 Nano 26 .1000-.1552 Nano © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. A 15 SERIES 88 SuperFly® Connectors Vertical PCB Footprints Viewed from rear PC tail side of unshrouded (Type A) insert. Use mirror image for shrouded (Type B) insert. PC Tail Wire Diameter By Contact Size Insert Arrangement A #23 contact uses #24 wire Ø.020 PCB Footprint Ø.588 (14.94) 4x Standoff K19M 0 1 2 3 4 5 6 7 8 9 10 11 12 4x 90° 15 16 13 14 17 18 19 Ø.477(12.11) Ø.528 (13.41) Ø.588 (14.94) 4x Standoff K13M19N 1 13 12 11 10 2 3 14 15 16 17 18 19 20 4 21 22 23 24 25 26 27 28 29 30 31 32 6 9 5 4x 90° 7 8 Ø.477 (12.12) Ø.528 (13.41) Ø.628 (15.95) 4x Standoff 5 1 2 3 4 6 7 8 9 10 11 12 13 0 14 15 16 17 18 19 20 21 22 Ø.517 (13.13) Ø.568 (14.43) 0 16 Tag X Loc Y Loc Size 14-.0500 .0866 Nano 15.0000.0866Nano 16.0500.0866Nano 17-.0750 .0433 Nano 18-.0250 .0433 Nano 19.0250.0433Nano 20.0750.0433Nano 21-.1000 .0000 Nano 22-.0500 .0000 Nano 23.0000.0000Nano 24.0500.0000Nano 25.1000.0000Nano 26-.0750-.0433 Nano 27-.0250-.0433 Nano 28 .0250-.0433 Nano 29 .0750-.0433 Nano 30-.0500-.0866 Nano 31 .0000-.0866 Nano 32 .0500-.0866 Nano Tag X Loc Y Loc Size 1 -.0975.1126Micro 2 -.0325.1126Micro 3 .0325.1126Micro 4 .0975.1126Micro 5 -.1300.0563Micro 6 -.0650.0563Micro 7 .0000.0563Micro 8 .0650.0563Micro 9 .1300.0563Micro 10-.0975 .0000 Micro 11-.0325 .0000 Micro Tag X Loc Y Loc Size 12.0325.0000Micro 13.0975.0000Micro 14-.1300-.0563 Micro 15-.0650-.0563 Micro 16 .0000-.0563 Micro 17 .0650-.0563 Micro 18 .1300-.0563 Micro 19-.0975-.1126 Micro 20-.0325-.1126 Micro 21 .0325-.1126 Micro 22 .0975-.1126 Micro 45° 4x .080 (2.05) L22M Tag X Loc Y Loc Size 1 -.0415.1546Micro 2 .0415.1546Micro 3 .1081.1180Micro 4 .1504.0548Micro 5 .1587-.0209 Micro 6 .1311-.0918 Micro 7 .0739-.1420 Micro 8 .0000-.1600 Micro 9 -.0739-.1420 Micro 10-.1311-.0918 Micro 11-.1587-.0209 Micro 12-.1504 .0548 Micro 13-.1081 .1180 Micro X 0 Y Tag X Loc Y Loc Size 11.0650.0000Micro 12.1300.0000Micro 13-.0975-.0563 Micro 14-.0325-.0563 Micro 15 .0325-.0563 Micro 16 .0975-.0563 Micro 17-.0650-.1126 Micro 18 .0000-.1126 Micro 19 .0650-.1126 Micro 45° 4x .080 (2.03) 0 Tag X Loc Y Loc Size 1 -.0650.1126Micro 2 .0000.1126Micro 3 .0650.1126Micro 4 -.0975.0563Micro 5 -.0325.0563Micro 6 .0325.0563Micro 7 .0975.0563Micro 8 -.1300.0000Micro 9 -.0650.0000Micro 10.0000.0000Micro X 0 Y Nano contact uses #30 wire Ø.010 Contact Location 4x .080 (2.03) Y Micro contact uses #26 wire Ø.016 X 45° 4x 90° © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 88 SuperFly® Connectors Right Angle PCB Footprints Viewed from rear PC tail side of shrouded (Type B) insert. Use mirror image for unshrouded (Type A) insert. PC Tail Wire Diameter By Contact Size #23 contact uses #24 wire Ø.020 Insert Arrangement PCB Footprint Micro contact uses #26 wire Ø.016 Contact Location 2x .080 (2.03) 4x Standoffs Y 0 1 3 2 4 5 7 A Tag X Loc Y Loc Cont Size 1 .0250.0433Nano 2 -.0250.0433Nano 3 .0500.0000Nano 4 .0000.0000Nano 5 -.0500.0000Nano 6 .0250-.0433 Nano 7 -.0250-.0433 Nano Front Of Connector B7N Nano contact uses #30 wire Ø.010 .230 (5.84) 6 X 0 .338 (8.59) Front Of Connector 2x .080 (2.03) 4x Standoffs Y C10N 0 2 5 4 8 1 3 7 .250 (6.35) 6 Tag X Loc Y Loc Cont Size 1 .0250.0683Nano 2 -.0250.0683Nano 3 .0500.0250Nano 4 .0000.0250Nano 5 -.0500.0250Nano Tag X Loc Y Loc Cont Size 6 .0500-.0250 Nano 7 .0000-.0250 Nano 8 -.0500-.0250 Nano 9 .0250-.0683 Nano 10-.0250-.0683 Nano Tag X Loc Y Loc Cont Size 1 .0250.0550Nano 2 -.0250.0550Nano Tag X Loc Y Loc Cont Size 3 .0325-.0280 Micro 4 -.0325-.0280 Micro 9 10 X 0 .358 (9.09) Front Of Connector 2x .080 (2.03) 4x Standoffs C2M2N 1 2 Y .250 (6.35) 0 4 3 X 0 .358 (9.09) Front Of Connector 2x .080 (2.03) 4x Standoffs D3M Y 0 Tag X Loc Y Loc Cont Size 1 .0000.0373Micro 2 .0325-.0190 Micro 3 -.0325-.0190 Micro 1 .269 (6.83) 3 2 X 0 .377 (9.57) © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 17 SERIES 88 SuperFly® Connectors Right Angle PCB Footprints Viewed from rear PC tail side of shrouded (Type B) insert. Use mirror image for unshrouded (Type A) insert. PC Tail Wire Diameter By Contact Size #23 contact uses #24 wire Ø.020 Insert Arrangement PCB Footprint A 4x Standoffs Y 2 Nano contact uses #30 wire Ø.010 Contact Location Front Of Connector 2x .080 (2.03) D2W2N Micro contact uses #26 wire Ø.016 Tag X Loc Y Loc Cont Size 1 .0375.0222 #23 2 -.0375.0222 #23 Tag X Loc Y Loc Cont Size 3 .0250-.0544 Nano 4 -.0250-.0544 Nano 1 .269 (6.83) 0 3 4 X 0 .377 (9.57) Tag X Loc Y Loc Cont Size 1 .0000.0420 #23 2 .0375-.0230 #23 3 -.0375-.0230 #23 Front Of Connector 2x .080 (2.03) 4x Standoffs E3W 1 Y .289 (6.83) 0 2 3 X 0 .397 (9.57) Tag X Loc Y Loc Cont Size 1 .0325.0325Micro 2 -.0325.0325Micro 3 .0325-.0325 Micro 4 -.0325-.0325 Micro Front Of Connector 2x .080 (2.03) 4x Standoffs E4M Y 0 2 1 4 3 0 .289 (6.83) X .397 (9.57) Front Of Connector 2x .080 (2.03) 4x Standoffs 2 3 E19N Y 0 7 6 1 5 12 11 10 4 9 8 16 15 14 13 19 18 17 0 X .397 (9.57) 18 .289 (6.83) Tag X Loc Y Loc Cont Size 1 .0500.0866Nano 2 .0000.0866Nano 3 -.0500.0866Nano 4 .0750.0433Nano 5 .0250.0433Nano 6 -.0250.0433Nano 7 -.0750.0433Nano 8 .1000.0000Nano 9 .0500.0000Nano 10.0000.0000Nano Tag X Loc Y Loc Cont Size 11-.0500 .0000 Nano 12-.1000 .0000 Nano 13 .0750-.0433 Nano 14 .0250-.0433 Nano 15-.0250-.0433 Nano 16-.0750-.0433 Nano 17 .0500-.0866 Nano 18 .0000-.0866 Nano 19-.0500-.0866 Nano © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 88 SuperFly® Connectors Right Angle PCB Footprints Viewed from rear PC tail side of shrouded (Type B) insert. Use mirror image for unshrouded (Type A) insert. PC Tail Wire Diameter By Contact Size #23 contact uses #24 wire Ø.020 Insert Arrangement PCB Footprint 2x .080 (2.03) 4x Standoffs E4M4N 2 3 5 4 0 1 6 Nano contact uses #30 wire Ø.010 Contact Location Front Of Connector Y Micro contact uses #26 wire Ø.016 Tag X Loc Y Loc Cont Size 1 .0650.0000Micro 2 .0325.0719Micro 3 -.0325.0719Micro 4 -.0650.0000Micro A Tag X Loc Y Loc Cont Size 5 .0000.0156Nano 6 .0000-.0344 Nano 7 .0250-.0777 Nano 8 -.0250-.0777 Nano .289 (6.86) 7 8 X 0 .397 (9.57) Tag X Loc Y Loc Cont Size 1 .0375.0375 #23 2 -.0375.0375 #23 3 .0375-.0375 #23 4 -.0375-.0375 #23 Front Of Connector 2x .080 (2.03) 4x Standoffs F4W 1 2 Y .309 (7.85) 0 4 3 X 0 .417 (10.59) Tag X Loc Y Loc Cont Size 1 .0325.0563Micro 2 -.0325.0563Micro 3 .0650.0000Micro 4 .0000.0000Micro 5 -.0650.0000Micro 6 .0325-.0563 Micro 7 -.0325-.0563 Micro Front Of Connector 2x .080 (2.03) 4x Standoffs F7M 1 2 Y 5 3 4 0 .309 (7.85) 6 7 X 0 .417 (10.59) Front Of Connector 4 F22N Y 0 9 3 8 2 7 1 5 6 13 12 11 10 18 17 16 15 14 22 21 20 19 0 2x .080 (2.03) 4x Standoffs X .417 (10.59) .309 (7.85) Tag X Loc Y Loc Cont Size 1 .0750.0866Nano 2 .0250.0866Nano 3 -.0250.0866Nano 4 -.0750.0866Nano 5 .1000.0433Nano 6 .0500.0433Nano 7 .0000.0433Nano 8 -.0500.0433Nano 9 -.1000.0433Nano 10.0750.0000Nano 11.0250.0000Nano Tag X Loc Y Loc Cont Size 12-.0250 .0000 Nano 13-.0750 .0000 Nano 14 .1000-.0433 Nano 15 .0500-.0433 Nano 16 .0000-.0433 Nano 17-.0500-.0433 Nano 18-.1000-.0433 Nano 19 .0750-.0866 Nano 20 .0250-.0866 Nano 21-.0250-.0866 Nano 22-.0750-.0866 Nano © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 19 SERIES 88 SuperFly® Connectors Right Angle PCB Footprints Viewed from rear PC tail side of shrouded (Type B) insert. Use mirror image for unshrouded (Type A) insert. PC Tail Wire Diameter By Contact Size #23 contact uses #24 wire Ø.020 Insert Arrangement PCB Footprint A 2x .080 (2.03) 4x Standoffs F4M8N 3 2 5 4 0 7 10 9 12 1 6 Nano contact uses #30 wire Ø.010 Contact Location Front Of Connector Y Micro contact uses #26 wire Ø.016 Tag X Loc Y Loc Cont Size 1 .0813.0162Micro 2 .0325.0833Micro 3 -.0325.0833Micro 4 -.0813.0162Micro Tag X Loc Y Loc Cont Size 5 .0000.0270Nano 6 .0250-.0163 Nano 7 -.0250-.0163 Nano 8 .0500-.0596 Nano 9 .0000-.0596 Nano 10-.0500-.0596 Nano 11 .0250-.1029 Nano 12-.0250-.1029 Nano Tag X Loc Y Loc Cont Size 1 .0740-.0125 #23 2 .0375.0750 #23 3 -.0375.0750 #23 4 -.0740-.0125 #23 Tag X Loc Y Loc Cont Size 5 .0000.0000Nano 6 .0000-.0500 Nano 7 .0250-.0933 Nano 8 -.0250-.0933 Nano .309 (7.85) 8 11 0 X .417 (10.59) Front Of Connector 2x .080 (2.03) 4x Standoffs F4W4N 3 Y 2 5 0 4 .309 (7.85) 1 6 7 8 X 0 .417 (10.59) Front Of Connector 2x .080 (2.03) 4x Standoffs 1 2 Y G7W 5 3 4 7 0 .374 (9.50) 6 Tag X Loc Y Loc Cont Size 1 .0375.0650 #23 2 -.0375.0650 #23 3 .0750.0000 #23 4 .0000.0000 #23 5 -.0750.0000 #23 6 .0375-.0650 #23 7 -.0375-.0650 #23 0 X .436 (11.07) Front Of Connector 2x .080 (2.03) 4x Standoffs 1 2 G10M Y 0 4 5 3 .374 (9.50) 8 7 10 0 6 9 Tag X Loc Y Loc Cont Size 1 .0375.1025Micro 2 -.0375.1025Micro 3 .0750.0375Micro 4 .0000.0375Micro 5 -.0750.0375Micro 6 .0750-.0375 Micro 7 .0000-.0375 Micro 8 -.0750-.0375 Micro 9 .0375-.1025 Micro 10-.0375-.1025 Micro X .436 (11.07) 20 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 88 SuperFly® Connectors Right Angle PCB Footprints Viewed from rear PC tail side of shrouded (Type B) insert. Use mirror image for unshrouded (Type A) insert. PC Tail Wire Diameter By Contact Size #23 contact uses #24 wire Ø.020 Insert Arrangement PCB Footprint 4x Standoffs 1 2 G31N Y 6 5 13 12 11 4 3 10 9 8 18 17 16 15 14 24 23 22 21 20 19 0 .374 (9.50) 29 28 27 26 25 31 30 X 0 .436 (11.07) Front Of Connector 2x .080 (2.03) 4x Standoffs 4 5 Y G6M10N 0 6 3 8 2 7 .374 (9.50) 10 9 1 12 11 16 15 14 13 0 Nano contact uses #30 wire Ø.010 Contact Location Front Of Connector 2x .080 (2.03) 7 Micro contact uses #26 wire Ø.016 Tag X Loc Y Loc Cont Size 1 .0250.1299Nano 2 -.0250.1299Nano 3 .1000.0866Nano 4 .0500.0866Nano 5 .0000.0866Nano 6 -.0500.0866Nano 7 -.1000.0866Nano 8 .1250.0433Nano 9 .0750.0433Nano 10.0250.0433Nano 11-.0250 .0433 Nano 12-.0750 .0433 Nano 13-.1250 .0433 Nano 14.1000.0000Nano 15.0500.0000Nano 16.0000.0000Nano Tag X Loc Y Loc Cont Size 17-.0500 .0000 Nano 18-.1000 .0000 Nano 19 .1250-.0433 Nano 20 .0750-.0433 Nano 21 .0250-.0433 Nano 22-.0250-.0433 Nano 23-.0750-.0433 Nano 24-.1250-.0433 Nano 25 .1000-.0866 Nano 26 .0500-.0866 Nano 27 .0000-.0866 Nano 28-.0500-.0866 Nano 29-.1000-.0866 Nano 30 .0250-.1299 Nano 31-.0250-.1299 Nano Tag X Loc Y Loc Cont Size 1 .0900-.0214 Micro 2 .0872.0583Micro 3 .0325.1037Micro 4 -.0325.1037Micro 5 -.0872.0583Micro 6 -.0900-.0214 Micro Tag X Loc Y Loc Cont Size 7 .0250.0350Nano 8 -.0250.0350Nano 9 .0250-.0150 Nano 10-.0250-.0150 Nano 11 .0250-.0650 Nano 12-.0250-.0650 Nano 13 .0750-.1150 Nano 14 .0250-.1150 Nano 15-.0250-.1150 Nano 16-.0750-.1150 Nano Tag X Loc Y Loc Cont Size 1 .1035-.0227 Micro 2 .1006.0598Micro 3 .0413.1171Micro 4 -.0413.1171Micro 5 -.1006.0598Micro 6 -.1035-.0227 Micro Tag X Loc Y Loc Cont Size 7 .0500-.0716 Nano 8 .0500.0150Nano 9 .0250.1149Nano 10 .0250-.0283 Nano 11.0250.0583Nano 12 .0000-.0716 Nano 13.0000.0150Nano 14-.0250-.1149 Nano 15-.0250-.0283 Nano 16-.0250 .0583 Nano 17-.0500-.0716 Nano 18-.0500 .0150 Nano X A .436 (11.07) Front Of Connector 4 G6M12N Y 0 5 6 18 17 2x .080 (2.03) 4x Standoffs 3 16 11 13 15 10 12 14 9 2 8 7 X 0 .436 (11.07) 1 .374 (9.50) © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 21 SERIES 88 SuperFly® Connectors Right Angle PCB Footprints Viewed from rear PC tail side of shrouded (Type B) insert. Use mirror image for unshrouded (Type A) insert. PC Tail Wire Diameter By Contact Size #23 contact uses #24 wire Ø.020 Insert Arrangement PCB Footprint A H10W 2 0 1 5 4 8 7 Nano contact uses #30 wire Ø.010 Contact Location Front Of Connector 2x .080 (2.03) 4x Standoffs Y Micro contact uses #26 wire Ø.016 3 Tag X Loc Y Loc Cont Size 1 .0375.1025 #23 2 -.0375.1025 #23 3 .0750.0375 #23 4 .0000.0375 #23 5 -.0750.0375 #23 Tag X Loc Y Loc Cont Size 6 .0750-.0375 #23 7 .0000-.0375 #23 8 -.0750-.0375 #23 9 .0375-.1025 #23 10-.0375-.1025 #23 Tag X Loc Y Loc Cont Size 1 .0750.1299Nano 2 .0250.1299Nano 3 -.0250.1299Nano 4 -.0750.1299Nano 5 .1000.0866Nano 6 .0500.0866Nano 7 .0000.0866Nano 8 -.0500.0866Nano 9 -.1000.0866Nano 10.1250.0433Nano 11..0750 .0433 Nano 12.0250.0433Nano 13-.0250 .0433 Nano 14-.0750 .0433 Nano 15-.1250 .0433 Nano 16.1500.0000Nano 17.1000.0000Nano 18.0500.0000Nano 19.0000.0000Nano Tag X Loc Y Loc Cont Size 20-.0500 .0000 Nano 21-.1000 .0000 Nano 22-.1500 .0000 Nano 23 .1250-.0433 Nano 24 .0750-.0433 Nano 25 .0250-.0433 Nano 26-.0250-.0433 Nano 27-.0750-.0433 Nano 28-.1250-.0433 Nano 29 .1000-.0866 Nano 30 .0500-.0866 Nano 31 .0000-.0866 Nano 32-.0500-.0866 Nano 33-.1000-.0866 Nano 34 .0750-.1299 Nano 35 .0250-.1299 Nano 36-.0250-.1299 Nano 37-.0750-.1299 Nano Tag X Loc Y Loc Cont Size 1 .1200-.0500 #23 2 .1200.0500 #23 3 .0500.1200 #23 4 -.0500.1200 #23 5 -.1200.0500 #23 6 -.1200-.0500 #23 Tag X Loc Y Loc Cont Size 7 .0250.0388Nano 8 -.0250.0388Nano 9 .0500-.0045 Nano 10 .0000-.0045 Nano 11-.0500-.0045 Nano 12 .0250-.0478 Nano 13-.0250-.0478 Nano 14 .0500-.0911 Nano 15 .0000-.0911 Nano 16-.0500-.0911 Nano 17 .0750 -.1344 Nano 18 .0250-.1344 Nano 19-.0250-.1344 Nano 20-.0750-.1344 Nano .374 (9.50) 6 9 10 X 0 .476 (12.09) Front Of Connector 2x .080 (2.03) 4x Standoffs H37N Y 0 4 3 2 1 9 8 7 6 5 15 14 13 12 11 10 22 21 20 19 18 17 16 28 27 26 25 24 23 33 32 31 30 29 37 36 35 34 .374 (9.50) X 0 .476 (12.09) Front Of Connector 2x .080 (2.03) 4x Standoffs 4 H6W14N Y 0 3 5 8 7 11 10 9 6 13 12 16 15 14 20 19 18 17 X 0 .476 (12.09) 22 2 1 .374 (9.50) © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 88 SuperFly® Connectors Right Angle PCB Footprints Viewed from rear PC tail side of shrouded (Type B) insert. Use mirror image for unshrouded (Type A) insert. PC Tail Wire Diameter By Contact Size #23 contact uses #24 wire Ø.020 Insert Arrangement PCB Footprint J44N Y 0 2x .080 (2.03) 4x Standoffs .430 (10.92) X 0 .515 (13.08) Front Of Connector 2x .080 (2.03) 4x Standoffs 4 5 J7W19N Y 0 6 3 9 8 12 11 10 16 15 7 19 21 26 25 14 13 1 18 17 20 24 23 22 0 2 X .515 (13.08) Nano contact uses #30 wire Ø.010 Contact Location Front Of Connector 5 4 3 2 1 11 10 9 8 7 6 18 17 16 15 14 13 12 26 25 24 23 22 21 20 19 33 32 31 30 29 28 27 39 38 37 36 35 34 44 43 42 41 40 Micro contact uses #26 wire Ø.016 .430 (10.92) Tag X Loc Y Loc Cont Size 1 .1000.1299Nano 2 .0500.1299Nano 3 .0000.1299Nano 4 -.0500.1299Nano 5 -.1000.1299Nano 6 .1250.0866Nano 7 .0750.0866Nano 8 .0250.0866Nano 9 -.0250.0866Nano 10-.0750 .0866 Nano 11-.1250 .0866 Nano 12.1500.0433Nano 13.1000.0433Nano 14.0500.0433Nano 15.0000.0433Nano 16-.0500 .0433 Nano 17-.1000 .0433 Nano 18-.1500 .0433 Nano 19.1750.0000Nano 20.1250.0000Nano 21.0750.0000Nano 22.0250.0000Nano Tag X Loc Y Loc Cont Size 23-.0250 .0000 Nano 24-.0750 .0000 Nano 25-.1250 .0000 Nano 26-.1750 .0000 Nano 27 .1500-.0433 Nano 28 .1000-.0433 Nano 29 .0500-.0433 Nano 30 .0000-.0433 Nano 31-.0500-.0433 Nano 32-.1000-.0433 Nano 33-.1500-.0433 Nano 34 .1250-.0866 Nano 35-.0750-.0866 Nano 36 .0250-.0866 Nano 37-.0250-.0866 Nano 38-.0750-.0866 Nano 39-.1250-.0866 Nano 40 .1000-.1299 Nano 41 .0500-.1299 Nano 42 .0000-.1299 Nano 43-.0500-.1299 Nano 44-.1000-.1299 Nano Tag X Loc Y Loc Cont Size 1 .1299-.0850 #23 2 .1477.0160 #23 3 .0964.1049 #23 4 .0000.1400 #23 5 -.0964.1049 #23 6 -.1477.0160 #23 7 -.1299-.0850 #23 Tag X Loc Y Loc Cont Size 8 .0250.0613Nano 9 -.0250.0613Nano 10.0500.0180Nano 11.0000.0180Nano 12-.0500 .0180 Nano 13 .0750-.0253 Nano 14 .0250-.0253 Nano 15-.0250-.0253 Nano 16-.0750-.0253 Nano 17 .0500-.0686 Nano 18 .0000-.0686 Nano 19-.0500-.0686 Nano 20 .0250-.1119 Nano 21-.0250-.1119 Nano 22 .1000-.1552 Nano 23 .0500-.1552 Nano 24 .0000-.1552 Nano 25-.0500-.1552 Nano 26-.1000-.1552 Nano © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 23 A SERIES 88 SuperFly® Connectors Right Angle PCB Footprints Viewed from rear PC tail side of unshrouded (Type A) insert. Use mirror image for shrouded (Type B) insert. PC Tail Wire Diameter By Contact Size Insert Arrangement #23 contact uses #24 wire Ø.020 PCB Footprint A 2x .080 (2.03) 4x Standoffs 3 7 K19M 2 6 1 5 4 12 11 10 9 0 16 15 18 19 8 14 13 Nano contact uses #30 wire Ø.010 Contact Location Front Of Connector Y Micro contact uses #26 wire Ø.016 .450 (11.43) 17 Tag X Loc Y Loc Cont Size 1 .0650.1126Micro 2 .0000.1126Micro 3 -.0650.1126Micro 4 .0975 .0563 Micro 5 .0325.0563Micro 6 -.0325.0563Micro 7 -.0975.0563Micro 8 .1300.0000Micro 9 .0650.0000Micro 10.0000.0000Micro Tag X Loc Y Loc Cont Size 11-.0650 .0000 Micro 12-.1300 .0000 Micro 13 .0975-.0563 Micro 14 .0325-.0563 Micro 15-.0325-.0563 Micro 16-.0975-.0563 Micro 17 .0650-.1126 Micro 18 .0000-.1126 Micro 19-.0650-.1126 Micro Tag X Loc Y Loc Cont Size 1 .0415.1546Micro 2 -.0415.1546Micro 3 -.1081.1180Micro 4 -.1504.0548Micro 5 -.1587-.0209 Micro 6 -.1311-.0918 Micro 7 -.0739-.1420 Micro 8 .0000-.1600 Micro 9 .0739-.1420 Micro 10 .1311-.0918 Micro 11 .1587-.0209 Micro 12.1504.0548Micro 13.1081.1180Micro 14.0500.0866Micro 15.0000.0866Micro 16-.0500 .0866 Micro Tag X Loc Y Loc Cont Size 17.0750.0433Nano 18.0250.0433Nano 19-.0250 .0433 Nano 20-.0750 .0433 Nano 21.1000.0000Nano 22.0500.0000Nano 23.0000.0000Nano 24-.0500 .0000 Nano 25-.1000 .0000 Nano 26 .0750-.0433 Nano 27 .0250-.0433 Nano 28-.0250-.0433 Nano 29-.0750-.0433 Nano 30 .0500-.0866 Nano 31 .0000-.0866 Nano 32-.0500-.0866 Nano Tag X Loc Y Loc Cont Size 1 .0975.1126Micro 2 .0325.1126Micro 3 -.0325.1126Micro 4 -.0975.1126Micro 5 .1300.0563Micro 6 .0650.0563Micro 7 .0000.0563Micro 8 -.0650.0563Micro 9 -.1300.0563Micro 10.0975.0000Micro 11.0325.0000Micro Tag X Loc Y Loc Cont Size 12-.0325 .0000 Micro 13-.0975 .0000 Micro 14 .1300-.0563 Micro 15 .0650-.0563 Micro 16 .0000-.0563 Micro 17-.0650-.0563 Micro 18-.1300-.0563 Micro 19 .0975-.1126 Micro 20 .0325-.1126 Micro 21-.0325-.1126 Micro 22 -.0975 -.1126 Micro X 0 .534 (13.56) Front Of Connector 2x .080 (2.03) 4x Standoffs 3 K13M19N Y 0 4 5 2 1 13 16 15 14 20 19 18 17 12 25 24 23 22 21 11 29 28 27 26 6 32 31 30 7 .450 (11.43) 10 9 8 X 0 .534 (13.56) Front Of Connector 2x .080 (2.03) 4x Standoffs Y L22M 4 3 2 1 9 8 7 6 5 13 12 11 10 0 18 17 16 15 14 22 21 20 19 0 X .480 (12.19) .574 (14.58) 24 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 880 QDC COUPLING Quick Disconnect Connectors Pigtail, PCB and Solder Cup Superior ease of use and outstanding high-speed data performance G lenair Series 880 Quick Disconnect (QDC) SuperFly® connectors merge miniaturized quick disconnect technology with our weight saving nanominature, microminiature and AS39029 type (size #23) contacts. Machine aluminum or stainless steel housings provide rugged durability. All SuperFly® connectors are IP67 rated in mated condition. Available in factory-terminated cordsets, single-ended pigtails, solder cup, and discrete PCB termination receptacles for complete flexibility in cable and box configurations. QDC SuperFly connectors are available with a variety of cabling options (see Section D), including ultraflexible GhostWire or impedance-controlled twisted pairs for high-speed applications and a wide-range of insert arrangements from 3–44 contacts. Glenair, Inc. 1211 Air Way Glendale, CA 91201-2497 818-247-6000 [email protected] www.glenair.com SERIES 880 Quick Disconnect Product Selection Guide Pigtail Connectors PCB Connectors 880-001P 880-033P Cable Plug, Pigtail Wires Page 4 Page 28 880-026R Rear Panel Mount, Vertical PCB Receptacle Cable Receptacle, Pigtail Wires Page 18 Cable Receptacle, Solder Cup B Page 30 880-041R 880-009P Rear Panel Mount, Vertical PCB Receptacle with Mounting Holes Front Panel Mount Plug, Pigtail Wires Page 20 880-042R 880-003R Rear Panel Mount, Vertical PCB Receptacle with Ground Pins Front Panel Mount Receptacle, Pigtail Wires Page 10 Page 22 880-030R 880-010P Rear Panel Mount, Right Angle PCB Receptacle Rear Panel Mount Plug, Pigtail Wires Page 12 Page 24 880-037R 880-004R Rear Panel Mount, Right Angle PCB Receptacle with Mounting Holes Rear Panel Mount Receptacle, Pigtail Wires Page 14 Cable Plug, Solder Cup 880-032R 880-002R Page 8 880-025P Rear Panel Mount, Vertical PCB Plug Page 16 Page 6 Solder Cup Connectors Page 26 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 1 SERIES 880 QDC SuperFly Connectors ® Compact, ultralightweight SuperFly® QDC connectors feature push-pull coupling, EMI shielding and IP67 ingress protection. Available in a 27 layouts and 10 shell sizes for high-speed applications such as audio, video or data and power applications. Series 880 connectors are ideal for man-portable electronics where size and weight are prime considerations. Lightweight, Low Profile EMI Shielding Aluminum or SST Three contact sizes: 5 amp, 3 amp and 1 amp High Speed and Power Applications Meets MIL-STD-810 environmental requirements 5 Amp Socket Contact Band-Master Shield Termination Adapter 1 Amp Twistpin Contact 3 Amp Socket Contact 1 Amp Socket Contact 5 Amp Pin Contact 3 Amp Twistpin Contact Gold-plated Springs Epoxy Epoxy Jam Nut Series 880 QDC Plug 2 O-rings Series 880 QDC Receptacle Band-Master Shield Termination Adapter © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 880 Quick Disconnect Connector Properties Overview ABOUT SUPERFLY® MATERIALS AND FINISHES Four standard material and finish options are available. 1 Aluminum shell with Electroless Nickel (EN). High reflectivity and poor corrosion resistance make nickel a poor choice for tactical systems, but nickel is preferred for avionics systems, space vehicles, medical equipment and test gear where corrosion is not a primary concern. Nickel is highly conductive and is excellent for EMI-protected systems. 4 Aluminum shell with Olive Drab or Cadmium (OD over Cad). excellent, corrosion resistance and excellent conductivity. Non-reflective OD over Cad is a primary choice for defense and aerospace applications. Inherently lubricious, resists galling. 2 Aluminum shell with Black Zinc-Nickel (Zn-Ni). Although less conductive than other finishes, non-reflective black Zn-Ni is a typical choice for soldier gear and is RoHS compliant. Corrosion resistance is good. 5 6 3 Aluminum shell with Electroless Nickel-PTFE (EN-PTFE). Excellent durability, corrosion resistance and conductivity. Nonreflective EN-PTFE is a primary choice for any harsh environment. Inherently lubricious, resists galling. 7 Stainless steel shell with Zinc-Cobalt (ZN-CO). Excellent durability, corrosion resistance and conductivity. Non-reflective black finish is an excellent choice for any harsh environment. Stainless steel, Passivated finish. Excellent corrosion resistance, good conductivity. A good choice for high corrosion areas where EMI shielding is not a primary concern. Suitable for most aerospace and tactical gear. Stainless steel, Ni-PTFE finish. Excellent corrosion resistance and excellent conductivity. A good choice for high corrosion areas where EMI shielding is a primary concern. Highly conductive, non-reflective Ni-PTFE finish is suitable for all aerospace and tactical systems. Material and Finish Comparison Data Identification Material and Finish Glenair Code Corrosion Resistance RoHS Compliance* Conductivity Reflectivity Cost 1 2 3 4 5 6 7 Aluminum Electroless Nickel M Aluminum Black ZincNickel ZR Aluminum Electoless NickelPTFE MT Aluminum Olive Drab over Cadmium NF Stainless Steel Black ZincCobalt ZC Stainless Steel Passivated ZK Stainless Steel Electroless Nickel-PTFE ZMT Poor Good Excellent Very Good Excellent Excellent Excellent Yes Excellent Reflective $ Yes Good Non-reflective $$ Yes Excellent Non-reflective $$ No Excellent Non-reflective $$ No Excellent Non-reflective $$$$ Yes Good Reflective $$$$ Yes Excellent Non-reflective $$$$ * Meets DoD directives and European regulations for elimination of cadmium and hexavalent chromate. Product Specifications Current Rating (Size) Wire Size Dielectric Withstanding Voltage Contact Resistance Temperature Range Durability (mating cycles) Corrosion (salt fog) Water Immersion,Mated Ingress Protection Vibration Shock 5A (#23) #22-28 AWG 500Vac 20 milliohms 3A (Micro) 1A (Nano) #24-30 AWG #28-32 AWG 600Vac 250Vac 32 milliohms 80 milliohms -55°C to +150°C 2000 Nickel finish 48 hours, other finishes 500 hours MIL-STD-810 Method 512, 1 meter, 1 hour IP 67 37g 300g Materials and Finishes Property Insulator Shell 1A. Contact 3A. and 5A. Contact Encapsulant Wire Description Thermoplastic, glass-filled Aluminum or stainless steel Precious metal alloy pin, goldplated copper alloy socket Copper alloy, 50 microinches gold over nickel finish Epoxy Space Grade High strength silver-coated copper alloy, ETFE insulation (M22759/33) or equivalent © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 3 SERIES 880 Quick Disconnect 880-001P Cable Plug with Pigtail Wires and Integral Banding Porch Series 880 Quick-Disconnect (QDC) cable plugs are pre-wired and sealed with epoxy. Features an integral shield termination platform and Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. High-strength wire with crosslinked ETFE insulation crimped at factory to high performance contacts. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are critical. How To Order Shell Size and Insert Arrangements Insert Arrangement B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M B No. of Contacts #23 Micro Nano 5A. 3A. 1A. — — 7 — — 10 — 2 2 — 3 — 2 — 2 3 — — — 4 — — — 19 — 4 4 4 — — — 7 — — — 22 — 4 8 4 — 4 7 — — — 10 — — — 31 — 6 10 — 6 12 10 — — — — 37 6 — 14 — — 44 7 — 19 — 19 — — 13 19 — 22 — First letter of insert arrangement represents connector shell size, as in this example: K13M19N NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 4 Sample Part Number 880-001P A -B7N -M 004 Series 880-001P Insert Style A = Unshrouded Contacts B = Shrouded Contacts Shrouded contacts are recessed within the insulator Shell Size/ Insert Arr.1 See Shell Size and Insert Arrangement Table Material/ Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant Wire AWG See Wire Code Table Wire Type J = “Space Grade” wire M22759/33 or equivalent (ETFE) Wire Color 1 = White 5 = Full Color; 1-10 solid color, 11 and up are striped 7 = 10 Color Repeating; Wire #1 black, Wire #11 black, etc Wire Length Overall length (‘L’) in inches measured from front of connector J 1 -24 MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 880-001PA-B7N-M004J1-24-686A Plug Alternate Key Positions Suffix Code 686A 686B 686C 686D 686E 686F A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° Master Key B° A° © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 880 Quick Disconnect 880-001P Cable Plug with Pigtail Wires and Integral Banding Porch ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin Wire Code Table Layouts with 5A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — — E3W, F4W, #24 — — G7W, H10W #26 — — Layouts with 5A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — #28 #24 — #28 #26 — #28 — #30 D2W2N, F4W4N, #22 H6W14N, #24 — #30 J7W19N #26 — #30 #22 — #32 #24 — #32 #26 — #32 Layouts with 3A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 — D3M, E4M F7M, — #26 — G10M, K19M, — #28 — L22M — #30 — Layouts with 3A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 #28 — #26 #28 — #28 #28 C2M2N, — #24 #30 E4M4N, F4M8N G6M10N, — #26 #30 G6M12N, — #28 #30 K13M19N — #24 #32 — #26 #32 — #28 #32 Layouts with 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. B7N, C10N, — — #28 E19N, F22N, — — #30 G31N, H37N, — — #32 J44N Code 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket 100 200 300 Code 104 204 304 105 205 305 106 206 306 B 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin ‘L’ +1.00/-.00 (+25.4/-.00 .811 (20.61) .361 (9.17) Code ØA ØB 020 030 040 050 024 034 044 025 035 045 026 036 046 Code 004 005 Band-Master® Nano Band Shield Termination Platform Pigtail Wires Code Dimensions Shell Size B C D E F G H J K L A Max OD In. .317 .342 .355 .381 .400 .422 .459 .487 .509 .548 B Rear OD mm. 8.05 8.69 9.02 9.68 10.16 10.72 11.66 12.37 12.93 13.92 In. .197 .222 .235 .261 .280 .302 .339 .369 .391 .430 mm. 5.00 5.64 5.97 6.63 7.11 7.67 8.61 9.37 9.93 10.92 006 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 5 SERIES 880 Quick Disconnect 880-002R Cable Receptacle with Pigtail Wires and Integral Banding Porch Series 880 Quick-Disconnect (QDC) cable receptacles are pre-wired and sealed with epoxy. In-line receptacle has integral shield termination platform and Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. High-strength wire with crosslinked ETFE insulation crimped at factory to high performance contacts. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are critical. How To Order Shell Size and Insert Arrangements Insert Arrangement B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M B No. of Contacts #23 Micro Nano 5A. 3A. 1A. — — 7 — — 10 — 2 2 — 3 — 2 — 2 3 — — — 4 — — — 19 — 4 4 4 — — — 7 — — — 22 — 4 8 4 — 4 7 — — — 10 — — — 31 — 6 10 — 6 12 10 — — — — 37 6 — 14 — — 44 7 — 19 — 19 — — 13 19 — 22 — First letter of insert arrangement represents connector shell size, as in this example: K13M19N NOTES Sample Part Number 880-002R A -B7N -M 004 Series 880-002R Insert Style A = Unshrouded Contacts B = Shrouded Contacts Shrouded contacts are recessed within the insulator Shell Size/ Insert Arr.1 See Shell Size and Insert Arrangement Table Material/ Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant Wire AWG See Wire Code Table Wire Type J = “Space Grade” wire M22759/33 or equivalent (ETFE) Wire Color 1 = White 5 = Full Color; 1-10 solid color, 11 and up are striped 7 = 10 Color Repeating; Wire #1 black, Wire #11 black, etc Wire Length Overall length (‘L’) in inches measured from front of connector J 1 -24 MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 880-002RA-B7N-M004J1-24-686A Plug Alternate Key Positions Suffix Code 686A 686B 686C 686D 686E 686F A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° Master Key A° B° 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 6 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 880 Quick Disconnect 880-002R Cable Receptacle with Pigtail Wires and Integral Banding Porch ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin Wire Code Table Layouts with 5A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — — E3W, F4W, #24 — — G7W, H10W #26 — — Layouts with 5A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — #28 #24 — #28 #26 — #28 — #30 D2W2N, F4W4N, #22 H6W14N, #24 — #30 J7W19N #26 — #30 #22 — #32 #24 — #32 #26 — #32 Layouts with 3A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 — D3M, E4M F7M, — #26 — G10M, K19M, — #28 — L22M — #30 — Layouts with 3A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 #28 — #26 #28 — #28 #28 C2M2N, — #24 #30 E4M4N, F4M8N G6M10N, — #26 #30 G6M12N, — #28 #30 K13M19N — #24 #32 — #26 #32 — #28 #32 Layouts with 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. B7N, C10N, — — #28 E19N, F22N, — — #30 G31N, H37N, — — #32 J44N Code 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket 100 200 300 Code 104 204 304 105 205 305 106 206 306 Code 020 030 040 050 Code 024 034 044 025 035 045 026 036 046 Code 004 005 006 B 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin ‘L’ +1.00/-.00 (+25.4/-.00 .806 (20.47) .313 (7.95) ØB Pigtail Wires ØA Band-Master® Nano Band Shield Termination Platform Dimensions Shell Size B C D E F G H J K L Ø A MAX In. .317 .342 .355 .381 .400 .422 .459 .487 .509 .548 ØB mm. 8.05 8.69 9.02 9.68 10.16 10.72 11.66 12.37 12.93 13.92 In. .197 .222 .235 .261 .280 .302 .339 .369 .391 .430 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. mm. 5.00 5.64 5.97 6.63 7.11 7.67 8.61 9.37 9.93 10.92 7 SERIES 880 Quick Disconnect 880-009P Front Panel Mount Plug with Pigtail Wires Series 880 Quick-Disconnect (QDC) front panel mount plugs are pre-wired and sealed with epoxy. Supplied with jam nut and o-ring. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. High-strength wire with crosslinked ETFE insulation crimped at factory to high performance contacts. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are critical. How To Order Shell Size and Insert Arrangements Insert Arrangements B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M B No. of Contacts #23 Micro Nano 5A. 3A. 1A. — — 7 — — 10 — 2 2 — 3 — 2 — 2 3 — — — 4 — — — 19 — 4 4 4 — — — 7 — — — 22 — 4 8 4 — 4 7 — — — 10 — — — 31 — 6 10 — 6 12 10 — — — — 37 6 — 14 — — 44 7 — 19 — 19 — — 13 19 — 22 — First letter of insert arrangement represents connector shell size, as in this example: K13M19N NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 8 Sample Part Number 880-009P A -B7N -M 004 Series 880-009P Insert Style A = Unshrouded Contacts B = Shrouded Contacts Shrouded contacts are recessed within the insulator Shell Size/ Insert Arr.1 See Shell Size and Insert Arrangement Table Material/ Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant Wire AWG See Wire Code Table Wire Type J = “Space Grade” wire M22759/33 or equivalent (ETFE) Wire Color 1 = White 5 = Full Color; 1-10 solid color, 11 and up are striped 7 = 10 Color Repeating; Wire #1 black, Wire #11 black, etc Wire Length Overall length (‘L’) in inches measured from front of connector J 1 -24 MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 880-009PA-B7N-M004J1-24-686A Master Key Plug Alternate Key Positions Suffix Code 686A 686B 686C 686D 686E 686F A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° B° A° MOD-518 OPEN FACE SEALING For IP67 performance in open face (unmated) condition, use suffix -518. Example: 880-009PA-B7N-M004J1-24-518 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 880 Quick Disconnect 880-009P Front Panel Mount Plug with Pigtail Wires ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin Wire Code Table Layouts with 5A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — — E3W, F4W, #24 — — G7W, H10W #26 — — Layouts with 5A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — #28 #24 — #28 #26 — #28 — #30 D2W2N, F4W4N, #22 H6W14N, #24 — #30 J7W19N #26 — #30 #22 — #32 #24 — #32 #26 — #32 Layouts with 3A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 — D3M, E4M F7M, — #26 — G10M, K19M, — #28 — L22M — #30 — Layouts with 3A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 #28 — #26 #28 — #28 #28 C2M2N, — #24 #30 E4M4N, F4M8N G6M10N, — #26 #30 G6M12N, — #28 #30 K13M19N — #24 #32 — #26 #32 — #28 #32 Layouts with 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. B7N, C10N, — — #28 E19N, F22N, — — #30 G31N, H37N, — — #32 J44N Code 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket 100 200 300 Code 104 204 304 105 205 305 106 206 306 Code Unshrouded Type A Insert 024 034 044 025 035 045 026 036 046 Code 004 005 006 1 Amp Nano Socket 5 Amp #23 Pin ‘L’ +1.00/-.00 (+25.4/-.00) .741 (18.82) .206 (5.23) 020 030 040 050 Code B 3 Amp Micro Socket .450 (11.43) ØA øB C Pigtail Wires .125 (3.18) Max Panel Thickness RECOMMENDED PANEL CUTOUT Dimensions Shell Size B C D E F G H J K L A Max OD In. mm. .392 9.96 .412 10.46 .432 10.97 .451 11.46 .471 11.96 .490 12.45 .530 13.46 .569 14.45 .589 14.96 .628 15.95 B Mount Ø In. mm. .283 7.19 .305 7.75 .324 8.23 .344 8.74 .364 9.25 .383 9.73 .419 10.64 .459 11.66 .478 12.14 .518 13.16 C Flats In. .241 .261 .281 .300 .320 .340 .379 .418 .438 .478 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. mm. 6.12 6.63 7.14 7.62 8.13 8.64 9.63 10.62 11.13 12.14 9 SERIES 880 Quick Disconnect 880-003R Front Panel Mount Receptacle with Pigtail Wires Series 880 Quick-Disconnect (QDC) front panel mount receptacles are pre-wired and sealed with epoxy. Integral shield termination platform. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. High-strength wire with crosslinked ETFE insulation crimped at factory to high performance contacts. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are critical. Shell Size and Insert Arrangements Insert Arrangements B B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M #23 5A. — — — — 2 3 — — — 4 — — — 4 7 — — — — 10 — 6 — 7 — — — No. of Contacts Micro Nano 3A. 1A. — 7 — 10 2 2 3 — — 2 — — 4 — — 19 4 4 — — 7 — — 22 4 8 — 4 — — 10 — — 31 6 10 6 12 — — — 37 — 14 — 44 — 19 19 — 13 19 22 — First letter of insert arrangement represents connector shell size, as in this example: K13M19N NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 10 Sample Part Number 880-003R A -B7N -M 004 Series 880-003R Insert Style A = Unshrouded Contacts B = Shrouded Contacts Shrouded contacts are recessed within the insulator Shell Size/ Insert Arr.1 See Shell Size and Insert Arrangement Table Material/ Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant Wire AWG See Wire Code Table Wire Type J = “Space Grade” wire M22759/33 or equivalent (ETFE) Wire Color 1 = White 5 = Full Color; 1-10 solid color, 11 and up are striped 7 = 10 Color Repeating; ( Wire #1 black, Wire #11 black, etc) Wire Length Overall length (‘L’) in inches measured from front of connector J 1 -24 MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 880-003RA-B7N-M004J1-24-686A Plug Alternate Key Positions Suffix Code 686A 686B 686C 686D 686E 686F A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° Master Key A° B° MOD-518 OPEN FACE SEALING For IP67 performance in open face (unmated) condition, use suffix -518. Example: 880-003RA-B7N-M004J1-24-518 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 880 Quick Disconnect 880-003R Front Panel Mount Receptacle with Pigtail Wires ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin Wire Code Table Layouts with 5A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — — E3W, F4W, #24 — — G7W, H10W #26 — — Layouts with 5A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — #28 #24 — #28 #26 — #28 — #30 D2W2N, F4W4N, #22 H6W14N, #24 — #30 J7W19N #26 — #30 #22 — #32 #24 — #32 #26 — #32 Layouts with 3A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 — D3M, E4M F7M, — #26 — G10M, K19M, — #28 — L22M — #30 — Layouts with 3A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 #28 — #26 #28 — #28 #28 C2M2N, — #24 #30 E4M4N, F4M8N G6M10N, — #26 #30 G6M12N, — #28 #30 K13M19N — #24 #32 — #26 #32 — #28 #32 Layouts with 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. B7N, C10N, — — #28 E19N, F22N, — — #30 G31N, H37N, — — #32 J44N Code 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket 100 200 300 Code 104 204 304 105 205 305 106 206 306 Code 020 030 040 050 Code 024 034 044 025 035 045 026 036 046 Code 004 005 B 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin ‘L’ +1.00/-.00 (+25.4/-.00 .620 (15.75) .535 (13.59) Pigtail Wires ØB ØA øC D Band-Master® Nano Band Shield Termination Platform (Apply Band After Installation) .125 (3.18) Max Panel Jam Nut, O-ring RECOMMENDED PANEL CUTOUT Dimensions Shell Size B C D E F G H J K L A Max OD In. mm. .392 9.96 .412 10.46 .432 10.97 .451 11.46 .471 11.96 .490 12.45 .530 13.46 .569 14.45 .589 14.96 .628 15.95 B Rear OD In. mm. .214 5.44 .239 6.07 .252 6.40 .278 7.06 .297 7.54 .319 8.10 .356 9.04 .384 9.75 .406 10.31 .445 11.30 C Mount Dia In. mm. .283 7.19 .305 7.75 .324 8.23 .344 8.74 .364 9.25 .383 9.73 .419 10.64 .459 11.66 .478 12.14 .518 13.16 In. .241 .261 .281 .300 .320 .340 .379 .418 .438 .478 D Flats mm. 6.12 6.63 7.14 7.62 8.13 8.64 9.63 10.62 11.13 12.14 006 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 11 SERIES 880 Quick Disconnect 880-010P Rear Panel Mount Plug with Pigtail Wires Series 880 Quick-Disconnect (QDC) rear panel mount plugs are pre-wired and sealed with epoxy. Supplied with jam nut and o-ring. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. High-strength wire with crosslinked ETFE insulation crimped at factory to high performance contacts. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are critical. How To Order Shell Size and Insert Arrangements Insert Arrangements B B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M No. of Contacts #23 Micro Nano 5A. 3A. 1A. — — 7 — — 10 — 2 2 — 3 — 2 — 2 3 — — — 4 — — — 19 — 4 4 4 — — — 7 — — — 22 — 4 8 4 — 4 7 — — — 10 — — — 31 — 6 10 — 6 12 10 — — — — 37 6 — 14 — — 44 7 — 19 — 19 — — 13 19 — 22 — First letter of insert arrangement represents connector shell size, as in this example: K13M19N NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 12 Sample Part Number 880-010P A -B7N -M 004 Series 880-010P Insert Style A = Unshrouded Contacts B = Shrouded Contacts Shrouded contacts are recessed within the insulator Shell Size/ Insert Arr.1 See Shell Size and Insert Arrangement Table Material/ Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant Wire AWG See Wire Code Table Wire Type J = “Space Grade” wire M22759/33 or equivalent (ETFE) Wire Color 1 = White 5 = Full Color; 1-10 solid color, 11 and up are striped 7 = 10 Color Repeating; Wire #1 black, Wire #11 black, etc Wire Length Overall length (‘L’) in inches measured from front of connector J 1 -24 MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 880-010PA-B7N-M004J1-24-686A Plug Alternate Key Positions Suffix Code 686A 686B 686C 686D 686E 686F A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° Master Key B° A° MOD-518 OPEN FACE SEALING For IP67 performance in open face (unmated) condition, use suffix -518. Example: 880-010PA-B7N-M004J1-24-518 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 880 Quick Disconnect 880-010P Rear Panel Mount Plug with Pigtail Wires ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin Wire Code Table Layouts with 5A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — — E3W, F4W, #24 — — G7W, H10W #26 — — Layouts with 5A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — #28 #24 — #28 #26 — #28 — #30 D2W2N, F4W4N, #22 H6W14N, #24 — #30 J7W19N #26 — #30 #22 — #32 #24 — #32 #26 — #32 Layouts with 3A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 — D3M, E4M F7M, — #26 — G10M, K19M, — #28 — L22M — #30 — Layouts with 3A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 #28 — #26 #28 — #28 #28 C2M2N, — #24 #30 E4M4N, F4M8N G6M10N, — #26 #30 G6M12N, — #28 #30 K13M19N — #24 #32 — #26 #32 — #28 #32 Layouts with 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. B7N, C10N, — — #28 E19N, F22N, — — #30 G31N, H37N, — — #32 J44N Code 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket 100 200 300 Code 104 204 304 105 205 305 106 206 306 Code Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin 24.0 (610) .064 (1.63) .750 (19.05) .236 (5.99) ØA 020 030 040 050 Code 024 034 044 025 035 045 026 036 046 Code 004 005 006 B 3 Amp Micro Socket øB C Pigtail Wires Jam Nut .125 (3.18) Max Panel Thickness RECOMMENDED PANEL CUTOUT Dimensions Shell Size B C D E F G H J K L A Max OD In. mm. .392 9.96 .412 10.46 .432 10.97 .451 11.46 .471 11.96 .490 12.45 .530 13.46 .569 14.45 .589 14.96 .628 15.95 B Mount Ø In. mm. .283 7.19 .305 7.75 .324 8.29 .344 8.74 .364 9.25 .383 9.73 .419 10.64 .459 11.66 .478 12.14 .518 13.16 C Flats In. .241 .261 .281 .300 .320 .340 .379 .418 .438 .478 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. mm. 6.12 6.63 7.14 7.62 8.13 8.64 9.63 10.62 11.13 12.14 13 SERIES 880 Quick Disconnect 880-004R Rear Panel Mount Receptacle with Pigtail Wires Series 880 Quick-Disconnect (QDC) rear panel mount receptacles are pre-wired and sealed with epoxy. Integral shield termination platform. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. High-strength wire with crosslinked ETFE insulation crimped at factory to high performance contacts. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are critical. How To Order Shell Size and Insert Arrangements Insert Arrangements B B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M No. of Contacts #23 Micro Nano 5A. 3A. 1A. — — 7 — — 10 — 2 2 — 3 — 2 — 2 3 — — — 4 — — — 19 — 4 4 4 — — — 7 — — — 22 — 4 8 4 — 4 7 — — — 10 — — — 31 — 6 10 — 6 12 10 — — — — 37 6 — 14 — — 44 7 — 19 — 19 — — 13 19 — 22 — First letter of insert arrangement represents connector w example: K13M19N NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 14 Sample Part Number 880-004R A -B7N -M 004 Series 880-004R Insert Style A = Unshrouded Contacts B = Shrouded Contacts recessed within insulator Shell Size/ Insert Arr.1 See Shell Size and Insert Arrangement Table Material/ Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant Wiring AWG See Wire Code Table Wiring Type J = “Space Grade” wire M22759/33 or equivalent (ETFE) Wire Color 1 = White 5 = Full Color; 1-10 solid color, 11 and up are striped 7 = 10 Color Repeating ( Wire #1 black, Wire #11 black, etc) Wire Length Overall length (‘L’) in inches measured from front of connector J 1 -24 MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 880-004RA-B7N-M004J1-24-686A Plug Alternate Key Positions Suffix Code 686A 686B 686C 686D 686E 686F A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° Master Key A° B° MOD-518 OPEN FACE SEALING For IP67 performance in open face (unmated) condition, use suffix -518. Example: 880-004RA-B7N-M004J1-24-518 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 880 Quick Disconnect 880-004R Rear Panel Mount Receptacle with Pigtail Wires ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin Wire Code Table Layouts with 5A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — — E3W, F4W, #24 — — G7W, H10W #26 — — Layouts with 5A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — #28 #24 — #28 #26 — #28 — #30 D2W2N, F4W4N, #22 H6W14N, #24 — #30 J7W19N #26 — #30 #22 — #32 #24 — #32 #26 — #32 Layouts with 3A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 — D3M, E4M F7M, — #26 — G10M, K19M, — #28 — L22M — #30 — Layouts with 3A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 #28 — #26 #28 — #28 #28 C2M2N, — #24 #30 E4M4N, F4M8N G6M10N, — #26 #30 G6M12N, — #28 #30 K13M19N — #24 #32 — #26 #32 — #28 #32 Layouts with 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. B7N, C10N, — — #28 E19N, F22N, — — #30 G31N, H37N, — — #32 J44N Code 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket 100 200 300 Code 104 204 304 105 205 305 106 206 306 Code 020 030 040 050 Code 024 034 044 025 035 045 026 036 046 Code 004 005 006 B 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin Jam Nut and O-ring ‘L’ .608 (15.44) Pigtail Wires .345 (8.76) Ø B øC ØA D Band-Master® Nano Band Shield Termination Platform .125 (3.18) Max Panel RECOMMENDED PANEL CUTOUT Dimensions Shell Size B C D E F G H J K L Ø A Max In. mm. .392 9.96 .412 9.96 .432 10.97 .451 11.46 .471 11.96 .490 12.45 .530 13.46 .569 14.45 .589 14.96 .628 15.95 B In. .234 .259 .272 .298 .317 .339 .376 .401 .421 .460 C mm. 5.94 6.58 6.91 7.57 8.05 8.61 9.55 10.19 10.69 11.68 In. .283 .305 .324 .344 .364 .383 .419 .459 .478 .518 ØD mm. 7.19 7.75 8.23 8.74 9.25 9.73 10.64 11.66 12.14 13.16 In. .241 .261 .281 .300 .320 .340 .379 .418 .438 .478 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. mm. 6.12 6.63 7.14 7.62 8.13 8.64 9.63 10.62 11.13 12.14 15 SERIES 880 Quick Disconnect 880-033P Rear Panel Mount, Vertical PCB Plug Series 880 Quick-Disconnect (QDC) rear panel mount, vertical PCB Plugs are sealed with epoxy and meet IP67 requirements in mated condition. For open face sealing in an unmated condition request modification code -518. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulator. High performance crimp contacts factory terminated to solid copper wire. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are critical. How To Order Shell Size and Insert Arrangements Insert Arrangements B B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M No. of Contacts #23 Micro Nano 5A. 3A. 1A. — — 7 — — 10 — 2 2 — 3 — 2 — 2 3 — — — 4 — — — 19 — 4 4 4 — — — 7 — — — 22 — 4 8 4 — 4 7 — — — 10 — — — 31 — 6 10 — 6 12 10 — — — — 37 6 — 14 — — 44 7 — 19 — 19 — — 13 19 — 22 — Sample Part Number 880-033P A Series 880-033P Insert Style A = Unshrouded Contacts B = Shrouded Contacts recessed within insulator Shell Size/ Insert Arr.1 See Shell Size and Insert Arrangement Table -B7N -M PC Tail Finish M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant S = Solder-dipped in 63/37 tin-lead G = Gold Plated PC Tail Length .080, .125, .175; Length (‘L’) in inches Material/ Finish2 S -.125 MOD-686 POLARIZING OPTIONS Standard Superfly connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 880-033PA-B7N-MS-.125-686A Master Key Plug Alternate Key Positions Suffix Code 686A 686B 686C 686D 686E 686F A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° B° A° First letter of insert arrangement represents connector shell size, as in this example: K13M19N NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 16 MOD-518 OPEN FACE SEALING For IP67 performance in open face (unmated) condition, use suffix -518. Example: 880-033PA-B7N-MS-.125-518 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 880 Quick Disconnect 880-033P Rear Panel Mount, Vertical PCB Plug ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket B 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin .877 (22.28) .686 (17.42) .236 (5.99) ØA D øC .020 (.508) "L" .125 (3.18) Max Panel Thickness Dimensions Shell Size B C D E F G H J K L øA In .392 .412 .432 .451 .471 .490 .530 .569 .589 .628 øB mm 9.96 10.46 10.97 11.46 11.96 12.45 13.46 14.45 14.96 15.95 In .392 .412 .432 .451 .471 .490 .530 .569 .589 .628 øC mm 9.96 10.46 10.97 11.46 11.96 12.45 13.46 14.45 14.96 15.95 In .283 .305 .324 .344 .364 .383 .419 .459 .478 .518 mm 7.19 7.75 8.23 8.74 9.25 9.73 10.64 11.66 12.14 13.16 D Flats In mm .241 6.12 .261 6.63 .281 7.14 .300 7.62 .320 8.13 .340 8.64 .379 9.63 .418 10.62 .438 11.13 .478 12.14 RECOMMENDED PANEL CUTOUT NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 17 SERIES 880 Quick Disconnect 880-032R Rear Panel Mount, Vertical PCB Receptacle Series 880 Quick-Disconnect (QDC) rear panel mount, vertical PCB receptacles are sealed with epoxy and meet IP67 requirements in mated condition. For open face sealing in an unmated condition request modification code -518. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulator. High performance crimp contacts factory terminated to solid copper wire. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are critical. How To Order Shell Size and Insert Arrangements Insert Arrangements B B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M No. of Contacts #23 Micro Nano 5A. 3A. 1A. — — 7 — — 10 — 2 2 — 3 — 2 — 2 3 — — — 4 — — — 19 — 4 4 4 — — — 7 — — — 22 — 4 8 4 — 4 7 — — — 10 — — — 31 — 6 10 — 6 12 10 — — — — 37 6 — 14 — — 44 7 — 19 — 19 — — 13 19 — 22 — Sample Part Number 880-032R Series 880-032R Insert Style A = Unshrouded Contacts B = Shrouded Contacts recessed within insulator Shell Size/ Insert Arr.1 See Shell Size and Insert Arrangement Table A -B7N -M PC Tail Finish M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant S = Solder-dipped in 63/37 tin-lead G = Gold Plated PC Tail Length .080, .125, .175; Length (‘L’) in inches Material/ Finish2 S -.125 MOD-686 POLARIZING OPTIONS Standard Superfly connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add sufix code 686 to the part number per the following example: 880-032RA-B7N-M004-.125-686A Plug Alternate Key Positions Suffix Code 686A 686B 686C 686D 686E 686F A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° Master Key A° B° First letter of insert arrangement represents connector shell size, as in this example: K13M19N MOD-518 OPEN FACE SEALING For IP67 performance in open face (unmated) condition, use suffix -518. Example: 880-032RA-B7N-M004-.125-518 18 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 880 Quick Disconnect 880-032R Rear Panel Mount, Vertical PCB Receptacle ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket B 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin .67 (17.02) .33 (8.38) ØA ØB D øC .025 (.64) "L" RECOMMENDED PANEL CUTOUT .125 (3.18) Max Panel Thickness Dimensions Shell Size B C D E F G H J K L øA In .392 .412 .432 .451 .471 .490 .530 .569 .589 .628 øB mm 9.9568 10.4648 10.9728 11.4554 11.9634 12.446 13.462 14.4526 14.9606 15.9512 In .392 .412 .432 .451 .471 .490 .530 .569 .589 .628 øC mm 9.96 10.46 10.97 11.46 11.96 12.45 13.46 14.45 14.96 15.95 In .283 .305 .324 .344 .364 .383 .419 .459 .478 .518 mm 7.19 7.75 8.23 8.74 9.25 9.73 10.64 11.66 12.14 13.16 D Flats In mm .241 6.12 .261 6.63 .281 7.14 .300 7.62 .320 8.13 .340 8.64 .379 9.63 .418 10.62 .438 11.13 .478 12.14 NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 19 SERIES 880 Quick Disconnect 880-041R Rear Panel Mount, PCB Receptacle with Mounting Holes Series 880 Quick-Disconnect (QDC) rear panel mount, PCB receptacles with mounting holes are sealed with epoxy and meet IP67 requirements in mated condition. For open face sealing in an unmated condition request modification code -518. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. High performance crimp contacts factory terminated to solid copper wire. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are critical. Shell Size and Insert Arrangements Insert Arrangements B B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M No. of Contacts #23 Micro Nano 5A. 3A. 1A. — — 7 — — 10 — 2 2 — 3 — 2 — 2 3 — — — 4 — — — 19 — 4 4 4 — — — 7 — — — 22 — 4 8 4 — 4 7 — — — 10 — — — 31 — 6 10 — 6 12 10 — — — — 37 6 — 14 — — 44 7 — 19 — 19 — — 13 19 — 22 — How To Order Sample Part Number 880-041R A Series 880-041R Insert Style A = Unshrouded Contacts B = Shrouded Contacts Recessed within Insulator Shell Size/ Insert Arr.1 See Shell Size and Insert Arrangement Table -B7N -M PC Tail Finish M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant S = Solder-dipped in 63/37 tin-lead G = Gold Plated PC Tail Length .080, .125, .175; Length (‘L’) in inches Material/ Finish2 S -.125 MOD-686 POLARIZING OPTIONS Standard Superfly connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add sufix code 686 to the part number per the following example: 880-041RA-B7N-MS-.125-686A Plug Alternate Key Positions Suffix Code 686A 686B 686C 686D 686E 686F A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° Master Key A° B° First letter of insert arrangement represents connector shell size, as in this example: K13M19N NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 20 MOD-518 OPEN FACE SEALING For IP67 performance in open face (unmated) condition, use suffix -518. Example: 880-041RA-B7N-MS-.125-518 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 880 Quick Disconnect 880-041R Rear Panel Mount, PCB Receptacle with Mounting Holes ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket B 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin .67 (17.02) .33 (8.38) .15 (3.81) 2-56 UNC 2B Thread Typ 2x øA .140 (3.56) .175 (4.45) øB L .025 (.64) .125 (3.18) Max Panel Thickness Full Rad C Dimensions Shell Size B C D E F G H J K L ØA In .392 .412 .432 .451 .471 .490 .530 .569 .589 .628 mm 9.96 10.46 10.97 11.46 11.96 12.45 13.46 14.45 14.96 15.95 ØB In .392 .412 .432 .451 .471 .490 .530 .569 .589 .628 C mm 9.96 10.46 10.97 11.46 11.96 12.45 13.46 14.45 14.96 15.95 In .540 .560 .579 .599 .619 .638 .678 .717 .737 .776 ØD mm 13.72 14.22 14.71 15.21 15.72 16.21 17.22 18.21 18.72 19.71 In .283 .305 .324 .344 .364 .383 .419 .459 .478 .518 mm 7.19 7.75 8.23 8.74 9.25 9.73 10.64 11.66 12.14 13.16 E Flats In mm .241 6.12 .261 6.63 .281 7.14 .300 7.62 .320 8.13 .340 8.64 .379 9.63 .418 10.62 .438 11.13 .478 12.14 E øD RECOMMENDED PANEL CUTOUT © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 21 SERIES 880 Quick Disconnect 880-042R Rear Panel Mount, PCB Receptacle with Ground Pins Series 880 Quick-Disconnect (QDC) rear panel mount, PCB receptacles are sealed with epoxy and meet IP67 requirements in mated condition. For open face sealing in an unmated condition request modification code -518. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. High performance crimp contacts are factory terminated to solid copper wire. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are critical. Shell Size and Insert Arrangements Insert Arrangements B B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M No. of Contacts #23 Micro Nano 5A. 3A. 1A. — — 7 — — 10 — 2 2 — 3 — 2 — 2 3 — — — 4 — — — 19 — 4 4 4 — — — 7 — — — 22 — 4 8 4 — 4 7 — — — 10 — — — 31 — 6 10 — 6 12 10 — — — — 37 6 — 14 — — 44 7 — 19 — 19 — — 13 19 — 22 — How To Order Sample Part Number 880-042R A Series 880-042R Insert Style A = Unshrouded Contacts B = Shrouded Contacts Recessed within Insulator Shell Size/ Insert Arr.1 See Shell Size and Insert Arrangement Table -B7N -M PC Tail Finish M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant S = Solder-dipped in 63/37 tin-lead G = Gold Plated PC Tail Length .080, .125, .175; Length (‘L’) in inches Material/ Finish2 S -.125 MOD-686 POLARIZING OPTIONS Standard Superfly connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add sufix code 686 to the part number per the following example: 880-042RA-B7N-MS-.125-686A Plug Alternate Key Positions Suffix Code 686A 686B 686C 686D 686E 686F A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° Master Key A° B° First letter of insert arrangement represents connector shell size, as in this example: K13M19N NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 22 MOD-518 OPEN FACE SEALING For IP67 performance in open face (unmated) condition, use suffix -518. Example: 880-042RA-B7N-MS-.125-518 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 880 Quick Disconnect 880-042R Rear Panel Mount, PCB Receptacle with Ground Pins ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket B 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin .67 (17.02) .145 (3.68) 4X ø.022/.018 (.56/.46) Ground Pin .33 (8.38) øA øB "L" .025 (.64) Typ .125 (3.18) Max Panel Thickness Dimensions Shell Size B C D E F G H J K L ØA In 0.392 0.412 0.431 0.451 0.471 0.490 0.530 0.569 0.588 0.628 ØB mm 9.96 10.46 10.95 11.46 11.96 12.45 13.46 14.45 14.94 15.95 In 0.516 0.536 0.555 0.575 0.595 0.614 0.654 0.693 0.712 0.752 ØC mm 13.11 13.61 14.10 14.61 15.11 15.60 16.61 17.60 18.08 19.10 In 0.283 0.305 0.324 0.344 0.364 0.383 0.419 0.459 0.478 0.518 mm 7.19 7.75 8.23 8.74 9.25 9.73 10.64 11.66 12.14 13.16 D Flats In mm 0.241 6.12 0.261 6.63 0.281 7.14 0.300 7.62 0.320 8.13 0.340 8.64 0.379 9.63 0.418 10.62 0.438 11.13 0.478 12.14 D øC RECOMMENDED PANEL CUTOUT © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 23 SERIES 880 Quick Disconnect 880-030R Rear Panel Mount, Right Angle PCB Receptacle Series 880 Quick-Disconnect (QDC) rear panel mount, PCB receptacles are sealed with epoxy and meet IP67 requirements in mated condition. For open face sealing in an unmated condition request modification code -518. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. High performance crimp contacts are factory terminated to solid copper wire. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are critical. Shell Size and Insert Arrangements Insert Arrangements B B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M No. of Contacts #23 Micro Nano 5A. 3A. 1A. — — 7 — — 10 — 2 2 — 3 — 2 — 2 3 — — — 4 — — — 19 — 4 4 4 — — — 7 — — — 22 — 4 8 4 — 4 7 — — — 10 — — — 31 — 6 10 — 6 12 10 — — — — 37 6 — 14 — — 44 7 — 19 — 19 — — 13 19 — 22 — How To Order Sample Part Number 880-030R A Series 880-030R Insert Style A = Unshrouded contacts B = Shrouded contacts recessed within insulator Shell Size/Insert Arr.1 See Shell Size and Insert Arrangement Table -B7N -M PC Tail Finish M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant S = Solder-dipped in 63/37 tin-lead G = Gold Plated PC Tail Length .080, .125, .175; Length (‘L’) in inches Material/Finish2 S -.125 MOD-686 POLARIZING OPTIONS Standard Superfly connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add sufix code 686 to the part number per the following example: 880-030RA-B7N-MS-.125-686A Plug Alternate Key Positions Suffix Code 686A 686B 686C 686D 686E 686F A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° Master Key A° B° First letter of insert arrangement represents connector shell size, as in this example: K13M19N NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 24 MOD-518 OPEN FACE SEALING For IP67 performance in open face (unmated) condition, use suffix -518. Example: 880-030RA-B7N-MS-.125-518 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 880 Quick Disconnect 880-030R Rear Panel Mount, Right Angle PCB Receptacle ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket B 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin .392 (9.96) 45° "E" .025 (.635) ØA "L" .722 (18.34) .752 (19.10) B C "ø D" RECOMMENDED PANEL CUTOUT Dimensions Shell Size B C D E F G H J K L A in 0.392 0.412 0.431 0.451 0.471 0.490 0.530 0.569 0.589 0.628 B mm 9.96 10.46 10.95 11.46 11.96 12.45 13.46 14.45 14.96 15.95 in 0.338 0.358 0.377 0.397 0.417 0.436 0.476 0.515 0.534 0.574 mm 8.59 9.09 9.58 10.08 10.59 11.07 12.09 13.08 13.56 14.58 C Max in mm 0.260 6.60 0.280 7.11 0.300 7.62 0.320 8.13 0.340 8.64 0.380 9.65 0.400 10.16 0.440 11.18 0.460 11.68 0.500 12.70 D Mount Ø in mm 0.283 7.19 0.305 7.75 0.324 8.23 0.344 8.74 0.364 9.25 0.383 9.73 0.419 10.64 0.459 11.66 0.478 12.14 0.518 13.16 E Flats in mm 0.241 6.12 0.261 6.63 0.281 7.14 0.300 7.62 0.320 8.13 0.340 8.64 0.379 9.63 0.418 10.62 0.438 11.13 0.478 12.14 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 25 SERIES 880 Quick Disconnect 880-037R Rear Panel Mount, Right Angle PCB Receptacle with Mounting Holes Series 880 Quick-Disconnect (QDC) rear panel mount, right angle PCB receptacles with mounting holes are sealed with epoxy and meet IP67 requirements in mated condition. For open face sealing in an unmated condition request modification code -518. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. High performance crimp contacts are factory terminated to solid copper wire. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are critical. Shell Size and Insert Arrangements Insert Arrangements B B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M No. of Contacts #23 Micro Nano 5A. 3A. 1A. — — 7 — — 10 — 2 2 — 3 — 2 — 2 3 — — — 4 — — — 19 — 4 4 4 — — — 7 — — — 22 — 4 8 4 — 4 7 — — — 10 — — — 31 — 6 10 — 6 12 10 — — — — 37 6 — 14 — — 44 7 — 19 — 19 — — 13 19 — 22 — How To Order Sample Part Number 880-037R Series 880-037R Insert Style A = Unshrouded Contacts B = Shrouded Contacts recessed within insulator Shell Size/ Insert Arr.1 See Shell Size and Insert Arrangement Table A -B7N -M PC Tail Finish M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant S = Solder-dipped in 63/37 tin-lead G = Gold Plated PC Tail Length .080, .125, .175; Length (‘L’) in inches Material/ Finish2 S -.125 MOD-686 POLARIZING OPTIONS Standard Superfly connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add sufix code 686 to the part number per the following example: 880-037RA-B7N-MS-.125-686A Plug Alternate Key Positions Suffix Code 686A 686B 686C 686D 686E 686F A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° Master Key A° B° First letter of insert arrangement represents connector shell size, as in this example: K13M19N NOTES MOD-518 OPEN FACE SEALING 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 26 For IP67 performance in open face (unmated) condition, use suffix -518. Example: 880-037RA-B7N-MS-.125-518 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 880 Quick Disconnect 880-037R Rear Panel Mount, Right Angle PCB Receptacle with Mounting Holes ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket B 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin Contact 'X' Ø.A .722 (18.34) .392 (9.96) 45° F D L "H" .025 (.635) Typ 4 Pl .025 (.64) "ø G" .752 (19.10) 2x 2-56 UNC 2B Th'd RECOMMENDED PANEL CUTOUT E B .282 (7.16) Shell Size Dimensions for Shell Size B thru G .140 (3.56) .140 (3.56) C B C D E F A In .392 .412 .431 .451 .471 B mm 9.96 10.46 10.95 11.46 11.96 In .338 .358 .377 .397 .417 mm 8.59 9.09 9.58 10.08 10.59 C Max In mm .230 5.84 .250 6.35 .269 6.83 .289 7.34 .309 7.85 D Ref In mm .417 10.59 .437 11.10 .456 11.58 .476 12.09 .496 12.60 E Basic In mm .330 8.38 .350 8.89 .350 8.89 .370 9.40 .370 9.40 F In .490 .510 .510 .530 .530 mm 12.45 12.95 12.95 13.46 13.46 GØ In mm .283 7.19 .305 7.75 .324 8.23 .344 8.74 .364 9.25 H Flats In mm .241 6.12 .261 6.63 .281 7.14 .300 7.62 .320 8.13 G .490 12.45 .436 11.07 .374 9.50 .516 13.11 .390 9.91 .550 13.97 .383 9.73 .340 8.64 H .532 13.51 .476 12.09 .374 9.50 .557 14.15 .390 9.91 .419 1.64 .379 9.63 .379 9.63 J .569 14.45 .515 13.08 .430 1.92 .594 15.09 .427 1.85 .459 11.66 .418 1.62 .418 1.62 K .588 14.94 .534 13.56 .450 11.43 .613 15.57 .446 11.33 .478 12.14 .438 11.13 .438 11.13 L .628 15.95 .574 14.58 .480 12.19 .653 16.59 .485 12.32 .518 13.16 .478 12.14 .478 12.14 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 27 SERIES 880 Quick Disconnect 880-025P In-Line Plug with Solder Cup Contacts 880-025P in-line plugs with solder cup contacts feature thread-on rear adapter allowing access to contacts. Install cable shield braid directly to connector with Band-Master Micro band. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. Ultraminiature SuperFly® connectors are ideal where ruggedness and field repairability is required. How To Order Shell Size and Insert Arrangements Insert Arrangements B B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M No. of Contacts #23 Micro Nano 5A. 3A. 1A. — — 7 — — 10 — 2 2 — 3 — 2 — 2 3 — — — 4 — — — 19 — 4 4 4 — — — 7 — — — 22 — 4 8 4 — 4 7 — — — 10 — — — 31 — 6 10 — 6 12 10 — — — — 37 6 — 14 — — 44 7 — 19 — 19 — — 13 19 — 22 — First letter of insert arrangement represents connector shell size, as in this example: K13M19N Sample Part Number 880-025P A -B7N -M Series 880-025P Insert Style A = Unshrouded Contacts B = Shrouded Contacts are Recessed within the Insulator Shell Size/ Insert Arr.1 See Shell Size and Insert Arrangement Table Material/ Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant MOD-686 POLARIZING OPTIONS Standard Superfly connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add sufix code 686 to the part number per the following example: 880-025PA-B7N-M-518 Plug Alternate Key Positions Suffix Code 686A 686B 686C 686D 686E 686F A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° Master Key B° A° SUITABLE WIRE RANGES Wire Ranges 5A (#23) 22-28 AWG 3A (Micro) 24-30 AWG 1A (Nano) 30-32 AWG NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 28 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 880 Quick Disconnect 880-025P In-Line Plug with Solder Cup Contacts ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket B 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin Dimensions Shell Size B C D E F G H J K L Ø A MAX In. .317 .342 .355 .381 .400 .422 .459 .487 .509 .548 ØB mm. 8.05 8.69 9.02 9.68 10.16 10.72 11.66 12.37 12.93 13.92 In. .197 .222 .235 .261 .280 .302 .339 .369 .391 .430 mm. 5.00 5.64 5.97 6.63 7.11 7.67 8.61 9.37 9.93 10.92 .361 (9.17) ØA .811 (20.61) ØB Shield Termination Platform © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 29 SERIES 880 Quick Disconnect 880-026R In-Line Receptacle with Solder Cup Contacts Series 880 Quick-Disconnect (QDC) in-line receptacles with solder cup contacts have thread-on rear adapter to allow access to contacts. Install cable shield braid directly to connector with Band-Master® band. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. Ultraminiature SuperFly® connectors are ideal where ruggedness and field repairability is required. How To Order Shell Size and Insert Arrangements Insert Arrangements B B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M No. of Contacts #23 Micro Nano 5A. 3A. 1A. — — 7 — — 10 — 2 2 — 3 — 2 — 2 3 — — — 4 — — — 19 — 4 4 4 — — — 7 — — — 22 — 4 8 4 — 4 7 — — — 10 — — — 31 — 6 10 — 6 12 10 — — — — 37 6 — 14 — — 44 7 — 19 — 19 — — 13 19 — 22 — First letter of insert arrangement represents connector shell size, as in this example: K13M19N Sample Part Number 880-026R A -B7N -M Series 880-026R Insert Style A = Unshrouded Contacts B = Shrouded Contacts, Recessed within Insulator Shell Size/ Insert Arr.1 See Shell Size and Insert Arrangement Table Material/ Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant MOD-686 POLARIZING OPTIONS Standard Superfly connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add sufix code 686 to the part number per the following example: 880-026RA-B7N-M-518 Plug Alternate Key Positions Suffix Code 686A 686B 686C 686D 686E 686F A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° Master Key A° B° SUITABLE WIRE RANGES Wire Ranges 5A (#23) 22-28 AWG 3A (Micro) 24-30 AWG 1A (Nano) 30-32 AWG NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 30 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 880 Quick Disconnect 880-026R In-Line Receptacle with Solder Cup Contacts ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket B 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin 0.806 (20.47) 0.313 (7.95) øA Bandmaster Nano Band Platform øB Dimensions Shell Size B C D E F G H J K L A Max OD In 0.317 0.342 0.355 0.381 0.400 0.422 0.459 0.487 0.509 0.548 B Rear OD mm 8.05 8.69 9.02 9.68 10.16 10.72 11.66 12.37 12.93 13.92 In 0.197 0.222 0.235 0.261 0.280 0.302 0.339 0.369 0.391 0.430 mm 5.00 5.64 5.97 6.63 7.11 7.67 8.61 9.37 9.93 10.92 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 31 SERIES 88 CORDSETS Superfly® Threaded Coupling Connectors High-performance, high-speed, lightweight, interconnect systems G lenair Series 881 SuperFly® threaded coupling connectors are the new standard for highspeed performance and ultraminiature interconnection systems. 27 contacts arrangements are offered with 1A, 3A, and 5A ratings. Aluminum and stainless shells with standard finishes including RoHs compliant options. Pigtail, and newly added, PCB and solder cup versions now available. Pigtail wire versions offered standard with high-strength silver-coated copper alloy wire with ETFE insulation (M222750/33 or equivalent). Glenair, Inc. 1211 Air Way Glendale, CA 91201-2497 818-247-6000 [email protected] www.glenair.com SERIES 881 Threaded Coupling Product Selection Guide Pigtail Connectors PCB Connectors 881-019R 881-001P Page 12 Cable Plug, Solder Cup Page 16 881-020R 881-002R 881-029R Rear Panel Mount, Right Angle PCB Receptacle Cable Receptacle, Pigtail Wires Page 6 881-018P Rear Panel Mount, Vertical PCB Receptacle Cable Plug, Pigtail Wires Page 4 Solder Cup Connectors Page 14 Cable Receptacle, Solder Cup Page 18 881-003R Front Panel Mount Receptacle, Pigtail Wires Page 8 C 881-004R Rear Panel Mount Receptacle, Pigtail Wires Page 10 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® catalog Dimensions in Inches (millimeters) are subject to change without notice. 1 SERIES 881 Threaded Coupling ® SuperFly Connectors C ompact, ultralightweight SuperFly® Threaded connectors feature positive lock coupling, EMI shielding and IP67 ingress protection . Available in a variety of layouts and sizes for audio, video, power and data applications, Series 881 connectors are ideal for man-portable electronics where size and weight are prime considerations. Ultrasmall size for maximum size and weight reduction Threaded coupling with positive lock Three contact sizes: 5 amp, 3 amp and 1 amp Meets MIL-STD-810 environmental requirements Aluminum or SST Epoxy Band-Master Shield Termination Adapter Coupling Nut Insulator Ground Springs 1 Amp Contact 1 Amp Contact O-ring Shell Band-Master Shield Termination Adapter 3 Amp Contact 3 Amp Contact Series 881 Plug Shown with Type A Unshrouded Insert 2 Shell Insulator Epoxy Series 881 Receptacle Shown with Type B Shrouded Insert © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 881 Threaded Coupling Connector Properties Overview ABOUT SUPERFLY® MATERIALS AND FINISHES Four standard material and finish options are available. 1 Aluminum shell with Electroless Nickel (EN). High reflectivity and poor corrosion resistance make nickel a poor choice for tactical systems, but nickel is preferred for avionics systems, space vehicles, medical equipment and test gear where corrosion is not a primary concern. Nickel is highly conductive and is excellent for EMI-protected systems. 4 Aluminum shell with Olive Drab or Cadmium (OD over Cad). excellent, corrosion resistance and excellent conductivity. Non-reflective OD over Cad is a primary choice for defense and aerospace applications. Inherently lubricious, resists galling. 2 Aluminum shell with Black Zinc-Nickel (Zn-Ni). Although less conductive than other finishes, non-reflective black Zn-Ni is a typical choice for soldier gear and is RoHS compliant. Corrosion resistance is good. 5 6 3 Aluminum shell with Electroless Nickel-PTFE (EN-PTFE). Excellent durability, corrosion resistance and conductivity. Nonreflective EN-PTFE is a primary choice for any harsh environment. Inherently lubricious, resists galling. 7 Stainless steel shell with Zinc-Cobalt (ZN-CO). Excellent durability, corrosion resistance and conductivity. Non-reflective black finish is an excellent choice for any harsh environment. Stainless steel, Passivated finish. Excellent corrosion resistance, good conductivity. A good choice for high corrosion areas where EMI shielding is not a primary concern. Suitable for most aerospace and tactical gear. Stainless steel, Ni-PTFE finish. Excellent corrosion resistance and excellent conductivity. A good choice for high corrosion areas where EMI shielding is a primary concern. Highly conductive, non-reflective Ni-PTFE finish is suitable for all aerospace and tactical systems. Material and Finish Comparison Data Property 1 2 3 4 5 6 7 Material and Finish Aluminum Electroless Nickel Aluminum Black ZincNickel Aluminum Electoless NickelPTFE Aluminum Olive Drab over Cadmium Stainless Steel Black ZincCobalt Stainless Steel Passivated Stainless Steel Electroless Nickel-PTFE M ZR MT NF ZC ZK ZMT Poor Good Excellent Very Good Excellent Excellent Excellent Yes Excellent Reflective $ Yes Good Non-reflective $$ Yes Excellent Non-reflective $$ No Excellent Non-reflective $$ No Excellent Non-reflective $$$$ Yes Good Reflective $$$$ Yes Excellent Non-reflective $$$$ Glenair Code Corrosion Resistance RoHS Compliance* Conductivity Reflectivity Cost * Meets DoD directives and European regulations for elimination of cadmium and hexavalent chromate. Current Rating (Size) Wire Size Dielectric Withstanding Voltage Contact Resistance Temperature Range Durability (mating cycles) Corrosion (salt fog) Water Immersion,Mated Ingress Protection Vibration Shock Product Specifications 5A (#23) 3A (Micro) 1A (Nano) #22-28 AWG #24-30 AWG #28-32 AWG 500Vac 600Vac 250Vac 20 milliohms 32 milliohms 80 milliohms -55°C to +150°C 2000 Nickel finish 48 hours, other finishes 500 hours MIL-STD-810 Method 512, 1 meter, 1 hour IP 67 37g 300g Materials and Finishes Property Description Insulator Thermoplastic, glass-filled Shell Aluminum or stainless steel Precious metal alloy pin, gold1A. Contact plated copper alloy socket 3A. and 5A. Copper alloy, 50 microinches Contact gold over nickel finish Encapsulant Epoxy High strength silver-coated Wire copper alloy, ETFE insulation (M22759/33 or equiv.) © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 3 SERIES 881 Threaded Coupling 881-001P Cable Plug with Pigtail Wires and Integral Banding Porch Series 881 threaded coupling cable plugs are pre-wired, sealed with epoxy and feature integral shield termination platform. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. High-strength wire with crosslinked ETFE insulation crimped at the factory to high performance contacts. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are critical. Shell Size and Insert Arrangements No. of Contacts Insert #23 Micro Nano Arrangements 5A. 3A. 1A. B7N — — 7 C10N — — 10 C2M2N — 2 2 D3M — 3 — D2W2N 2 — 2 E3W 3 — — E4M — 4 — E19N — — 19 E4M4N — 4 4 F4W 4 — — F7M — 7 — F22N — — 22 F4M8N — 4 8 F4W4N 4 — 4 G7W 7 — — G10M — 10 — G31N — — 31 G6M10N — 6 10 G6M12N — 6 12 H10W 10 — — H37N — — 37 H6W14N 6 — 14 J44N — — 44 J7W19N 7 — 19 K19M — 19 — K13M19N — 13 19 L22M — 22 — C First letter of insert arrangement represents connector shell size, as in this example K13M19N NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 4 How To Order Sample Part Number 881-001P A -B7N -M 004 Series 881-001P Insert Style A = Unshrouded Contacts B = Shrouded Contacts Shrouded contacts are recessed within the insulator Shell Size / Insert Arr.1 See Shell Size and Insert Arrangement Table Material/ Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant Wire AWG See Wire Code Table Wire Type J = “Space Grade” wire M22759/33 or equivalent (ETFE) Wire Color 1 = White 5 = Full Color; 1-10 solid color, 11 and up are striped 7 = 10 Color Repeating; Wire #1 black, Wire #11 black, etc Wire Length Overall length in inches measured from front of connector J 1 -24 MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 881-001PA-B7N-M004J1-24-686A Plug Alternate Key Positions Suffix Code A° B° 686A 150° 210° 686B 75° 210° 686C 95° 230° 686D 140° 275° 686E 75° 275° 686F 95° 210° Master Key B° A° © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 881 Threaded Coupling 881-001P Cable Plug with Pigtail Wires and Integral Banding Porch ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. Wire Code Table Layouts with 5A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — — E3W, F4W, #24 — — G7W, H10W #26 — — Layouts with 5A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — #28 #24 — #28 #26 — #28 — #30 D2W2N, F4W4N, #22 H6W14N, #24 — #30 J7W19N #26 — #30 #22 — #32 #24 — #32 #26 — #32 Layouts with 3A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 — D3M, E4M F7M, — #26 — G10M, K19M, — #28 — L22M — #30 — Layouts with 3A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 #28 — #26 #28 — #28 #28 C2M2N, — #24 #30 E4M4N, F4M8N G6M10N, — #26 #30 G6M12N, — #28 #30 K13M19N — #24 #32 — #26 #32 — #28 #32 Layouts with 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. B7N, C10N, — — #28 E19N, F22N, — — #30 G31N, H37N, — — #32 J44N 3 Amp Micro Twistpin Code 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket 100 200 300 Code 104 204 304 105 205 305 106 206 306 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin 24.0 (610) C .853 (21.67) .540 (13.72) Code ØA ØB 020 030 040 050 Code 024 034 044 025 035 045 026 036 046 Code 004 005 006 Pigtail Wires Band-Master Nano Band Shield Termination Platform Dimensions Shell Size B C D E F G H J K L ØA In. .356 .375 .395 .415 .434 .454 .493 .533 .553 .592 ØB mm. 9.04 9.53 10.03 10.54 11.02 11.53 12.52 13.54 14.05 15.04 In. .199 .224 .237 .263 .282 .304 .341 .369 .391 .430 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® catalog Dimensions in Inches (millimeters) are subject to change without notice. mm. 5.05 5.69 6.02 6.68 7.16 7.72 8.66 9.37 9.93 10.92 5 SERIES 881 Threaded Coupling 881-002R Cable Receptacle with Pigtail Wires and Banding Porch Series 881 threaded coupling cable receptacles are pre-wired, sealed with epoxy and feature an integral shield termination platform. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. High-strength wire with crosslinked ETFE insulation crimped at the factory to high performance contacts. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are critical. Shell Size and Insert Arrangements No. of Contacts Insert #23 Micro Nano Arrangements 5A. 3A. 1A. B7N — — 7 C10N — — 10 C2M2N — 2 2 D3M — 3 — D2W2N 2 — 2 E3W 3 — — E4M — 4 — E19N — — 19 E4M4N — 4 4 F4W 4 — — F7M — 7 — F22N — — 22 F4M8N — 4 8 F4W4N 4 — 4 G7W 7 — — G10M — 10 — G31N — — 31 G6M10N — 6 10 G6M12N — 6 12 H10W 10 — — H37N — — 37 H6W14N 6 — 14 J44N — — 44 J7W19N 7 — 19 K19M — 19 — K13M19N — 13 19 L22M — 22 — C First letter of insert arrangement represents connector shell size, as in this example K13M19N NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 6 How To Order Sample Part Number 881-002R A -B7N -M 004 Series 881-002R Insert Style A = Unshrouded Contacts B = Shrouded Contacts are recessed within the insulator Shell Size / Insert Arr.1 See Shell Size and Insert Arrangement Table Material/ Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant Wire AWG See Wire Code Table Wire Type J = “Space Grade” wire M22759/33 or equivalent (ETFE) Wire Color 1 = White 5 = Full Color; 1-10 solid color, 11 and up are striped 7 = 10 Color Repeating; Wire #1 black, Wire #11 black, etc Wire Length Overall length in inches measured from front of connector J 1 -24 MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 881-002RA-B7N-M004J1-24-686A Plug Alternate Key Positions Suffix Code A° B° 686A 150° 210° 686B 75° 210° 686C 95° 230° 686D 140° 275° 686E 75° 275° 686F 95° 210° Master Key A° B° © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 881 Threaded Coupling 881-002R Cable Receptacle with Pigtail Wires and Banding Porch ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. Wire Code Table Layouts with 5A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — — E3W, F4W, #24 — — G7W, H10W #26 — — Layouts with 5A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — #28 #24 — #28 #26 — #28 — #30 D2W2N, F4W4N, #22 H6W14N, #24 — #30 J7W19N #26 — #30 #22 — #32 #24 — #32 #26 — #32 Layouts with 3A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 — D3M, E4M F7M, — #26 — G10M, K19M, — #28 — L22M — #30 — Layouts with 3A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 #28 — #26 #28 — #28 #28 C2M2N, — #24 #30 E4M4N, F4M8N G6M10N, — #26 #30 G6M12N, — #28 #30 K13M19N — #24 #32 — #26 #32 — #28 #32 Layouts with 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. B7N, C10N, — — #28 E19N, F22N, — — #30 G31N, H37N, — — #32 J44N 3 Amp Micro Twistpin Code 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket 100 200 300 Code 104 204 304 105 205 305 106 206 306 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin 24.0 (610) .535 (13.59) Code 024 034 044 025 035 045 026 036 046 Code 004 005 006 ØA ØB 020 030 040 050 Code C .848 (21.54) Pigtail Wires Band-Master Nano Band Shield Termination Platform Dimensions Shell Size B C D E F G H J K L ØA In. .339 .364 .377 .403 .422 .444 .481 .509 .531 .570 ØB mm. 8.61 9.25 9.58 10.24 10.72 11.28 12.22 12.93 13.49 14.48 In. .199 .224 .237 .263 .282 .304 .341 .369 .391 .430 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® catalog Dimensions in Inches (millimeters) are subject to change without notice. mm. 5.05 5.69 6.02 6.68 7.16 7.72 8.66 9.37 9.93 10.92 7 SERIES 881 Threaded Coupling 881-003R Front Panel Mount Receptacle with Pigtail Wires Series 881 front panel mount, threaded coupling receptacles are pre-wired, sealed with epoxy and feature integral shield termination platform. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. High-strength wire with crosslinked ETFE insulation crimped at the factory to high performance contacts. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are critical. Shell Size and Insert Arrangements No. of Contacts Insert #23 Micro Nano Arrangements 5A. 3A. 1A. B7N — — 7 C10N — — 10 C2M2N — 2 2 D3M — 3 — D2W2N 2 — 2 E3W 3 — — E4M — 4 — E19N — — 19 E4M4N — 4 4 F4W 4 — — F7M — 7 — F22N — — 22 F4M8N — 4 8 F4W4N 4 — 4 G7W 7 — — G10M — 10 — G31N — — 31 G6M10N — 6 10 G6M12N — 6 12 H10W 10 — — H37N — — 37 H6W14N 6 — 14 J44N — — 44 J7W19N 7 — 19 K19M — 19 — K13M19N — 13 19 L22M — 22 — C First letter of insert arrangement represents connector shell size, as in this example K13M19N NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 8 How To Order Sample Part Number 881-003R A -B7N -M 004 Series 881-003R Insert Style A = Unshrouded Contacts B = Shrouded Contacts are recessed within the insulator Shell Size / Insert Arr.1 See Shell Size and Insert Arrangement Table Material/ Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant Wire AWG See Wire Code Table Wire Type J = “Space Grade” wire M22759/33 or equivalent (ETFE) Wire Color 1 = White 5 = Full Color; 1-10 solid color, 11 and up are striped 7 = 10 Color Repeating; Wire #1 black, Wire #11 black, etc Wire Length Overall length in inches measured from front of connector J 1 -24 MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 881-003RA-B7N-M004J1-24-686A Plug Alternate Key Positions Suffix Code A° B° 686A 150° 210° 686B 75° 210° 686C 95° 230° 686D 140° 275° 686E 75° 275° 686F 95° 210° Master Key A° B° MOD-518 OPEN FACE SEALING For IP67 performance in open face (unmated) condition, use suffix -518. Example: 881-003RA-B7N-M004J1-24-518 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 881 Threaded Coupling 881-003R Front Panel Mount Receptacle with Pigtail Wires ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. Wire Code Table Layouts with 5A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — — E3W, F4W, #24 — — G7W, H10W #26 — — Layouts with 5A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — #28 #24 — #28 #26 — #28 — #30 D2W2N, F4W4N, #22 H6W14N, #24 — #30 J7W19N #26 — #30 #22 — #32 #24 — #32 #26 — #32 Layouts with 3A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 — D3M, E4M F7M, — #26 — G10M, K19M, — #28 — L22M — #30 — Layouts with 3A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 #28 — #26 #28 — #28 #28 C2M2N, — #24 #30 E4M4N, F4M8N G6M10N, — #26 #30 G6M12N, — #28 #30 K13M19N — #24 #32 — #26 #32 — #28 #32 Layouts with 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. B7N, C10N, — — #28 E19N, F22N, — — #30 G31N, H37N, — — #32 J44N 3 Amp Micro Twistpin Code 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket 100 200 300 Code 104 204 304 105 205 305 106 206 306 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin 24.0 (610) .705 (17.91) .480 (12.19) Code C ØA ØC 020 030 040 050 B RECOMMENDED PANEL CUTOUT Pigtail Wires Code 024 034 044 025 035 045 026 036 046 Code 004 005 Shell Size B C D E F G H J K L ØA In. .392 .412 .432 .451 .471 .491 .530 .550 .570 .609 mm. 9.96 10.46 10.97 11.46 11.96 12.47 13.46 13.97 14.48 15.47 Dimensions B In. mm. .236 5.99 .256 6.50 .276 7.01 .296 7.52 .315 8.00 .335 8.51 .374 9.50 .394 10.01 .414 10.52 .453 11.51 ØC In. .282 .302 .321 .341 .361 .380 .420 .439 .459 .498 mm. 7.16 7.67 8.15 8.66 9.17 9.65 10.67 11.15 11.66 12.65 A Thread M7.0 x .75-6g M7.5x .75-6g M8.0 x .75-6g M8.5 x .75-6g M9.0 x .75-6g M9.5 x .75-6g M10.5 x .75-6g M11.5 x .75-6g M12.0 x .75-6g M13.0 x .75-6g 006 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® catalog Dimensions in Inches (millimeters) are subject to change without notice. 9 SERIES 881 Threaded Coupling 881-004R Rear Panel Mount Receptacle with Pigtail Wires Series 881 rear panel mount, threaded coupling receptacles are pre-wired, sealed with epoxy and feature integral shield termination platform. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. High-strength wire with crosslinked ETFE insulation crimped at the factory to high performance contacts. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are critical. C Shell Size and Insert Arrangements No. of Contacts Insert #23 Micro Nano Arrangements 5A. 3A. 1A. B7N — — 7 C10N — — 10 C2M2N — 2 2 D3M — 3 — D2W2N 2 — 2 E3W 3 — — E4M — 4 — E19N — — 19 E4M4N — 4 4 F4W 4 — — F7M — 7 — F22N — — 22 F4M8N — 4 8 F4W4N 4 — 4 G7W 7 — — G10M — 10 — G31N — — 31 G6M10N — 6 10 G6M12N — 6 12 H10W 10 — — H37N — — 37 H6W14N 6 — 14 J44N — — 44 J7W19N 7 — 19 K19M — 19 — K13M19N — 13 19 L22M — 22 — First letter of insert arrangement represents connector shell size, as in this example K13M19N NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 10 How To Order Sample Part Number 881-004R A -B7N -M 004 Series 881-004R Insert Style A = Unshrouded Contacts B = Shrouded Contacts are recessed within the insulator Shell Size / Insert Arr.1 See Shell Size and Insert Arrangement Table Material/ Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant Wire AWG See Wire Code Table Wire Type J = “Space Grade” wire M22759/33 or equivalent (ETFE) Wire Color 1 = White 5 = Full Color; 1-10 solid color, 11 and up are striped 7 = 10 Color Repeating; Wire #1 black, Wire #11 black, etc Wire Length Overall length (L) in inches measured from front of connector J 1 -24 MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 881-004RA-B7N-M004J1-24-686A Plug Alternate Key Positions Suffix Code A° B° 686A 150° 210° 686B 75° 210° 686C 95° 230° 686D 140° 275° 686E 75° 275° 686F 95° 210° Master Key A° B° MOD-518 OPEN FACE SEALING For IP67 performance in open face (unmated) condition, use suffix -518. Example: 881-004RA-B7N-M004J1-24-518 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 881 Threaded Coupling 881-004R Rear Panel Mount Receptacle with Pigtail Wires ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. Wire Code Table Layouts with 5A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — — E3W, F4W, #24 — — G7W, H10W #26 — — Layouts with 5A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — #28 #24 — #28 #26 — #28 — #30 D2W2N, F4W4N, #22 H6W14N, #24 — #30 J7W19N #26 — #30 #22 — #32 #24 — #32 #26 — #32 Layouts with 3A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 — D3M, E4M F7M, — #26 — G10M, K19M, — #28 — L22M — #30 — Layouts with 3A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 #28 — #26 #28 — #28 #28 C2M2N, — #24 #30 E4M4N, F4M8N G6M10N, — #26 #30 G6M12N, — #28 #30 K13M19N — #24 #32 — #26 #32 — #28 #32 Layouts with 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. B7N, C10N, — — #28 E19N, F22N, — — #30 G31N, H37N, — — #32 J44N 3 Amp Micro Twistpin Code 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket 100 200 300 Code 104 204 304 105 205 305 106 206 306 3 Amp Micro Socket Unshrouded Type A Insert 5 Amp #23 Pin L Code 020 030 040 050 Code 024 034 044 025 035 045 026 036 046 Code 004 005 006 1 Amp Nano Socket C .677 (17.20) .598 (15.19) ØA ØC B RECOMMENDED PANEL CUTOUT Pigtail Wires Dimensions Shell Size B C D E F G H J K L ØA In. .392 .412 .432 .451 .471 .491 .530 .569 .589 .628 B mm. 9.96 10.46 10.97 11.46 11.96 12.47 13.46 14.45 14.96 15.95 In. .236 .256 .276 .296 .315 .335 .374 .394 .433 .473 ØC mm. 5.99 6.50 7.01 7.52 8.00 8.51 9.50 10.01 11.00 12.01 In. .282 .302 .321 .341 .361 .380 .420 .439 .478 .518 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® catalog Dimensions in Inches (millimeters) are subject to change without notice. mm. 7.16 7.67 8.15 8.66 9.17 9.65 10.67 11.15 12.14 13.16 11 SERIES 881 Threaded Coupling 881-019R Rear Panel Mount, PCB Vertical Receptacle Series 881 rear panel mount, threaded coupling, PCB receptacles are sealed with epoxy and meet IP67 requirements in mated condition. For open face sealing in an unmated condition request modification code -518. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. High performance crimp contacts are factory terminated to solid copper wire. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are critical. C Shell Size and Insert Arrangements No. of Contacts Insert #23 Micro Nano Arrangements 5A. 3A. 1A. B7N — — 7 C10N — — 10 C2M2N — 2 2 D3M — 3 — D2W2N 2 — 2 E3W 3 — — E4M — 4 — E19N — — 19 E4M4N — 4 4 F4W 4 — — F7M — 7 — F22N — — 22 F4M8N — 4 8 F4W4N 4 — 4 G7W 7 — — G10M — 10 — G31N — — 31 G6M10N — 6 10 G6M12N — 6 12 H10W 10 — — H37N — — 37 H6W14N 6 — 14 J44N — — 44 J7W19N 7 — 19 K19M — 19 — K13M19N — 13 19 L22M — 22 — First letter of insert arrangement represents connector shell size, as in this example K13M19N NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 12 How To Order Sample Part Number 881-019R Series 881-019R Insert Style A = Unshrouded Contacts B = Shrouded Contacts are Recessed within Insulator Shell Size / Insert Arr.1 See Shell Size and Insert Arrangement Table A -B7N -M PC Tail Finish M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant S = Solder-dipped in 63/37 tin-lead G = Gold Plated PC Tail Length .080, .125, .175 in inches Material/ Finish2 S -.125 MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 881-019RA-B7N-MS-.125-686A Plug Alternate Key Positions Suffix Code A° B° 686A 150° 210° 686B 75° 210° 686C 95° 230° 686D 140° 275° 686E 75° 275° 686F 95° 210° Master Key A° B° MOD-518 OPEN FACE SEALING For IP67 performance in open face (unmated) condition, use suffix -518. Example: 881-019RA-B7N-MS-.125-518 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 881 Threaded Coupling 881-019R Rear Panel Mount, PCB Vertical Receptacle ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. Wire Code Table Layouts with 5A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — — E3W, F4W, #24 — — G7W, H10W #26 — — Layouts with 5A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — #28 #24 — #28 #26 — #28 — #30 D2W2N, F4W4N, #22 H6W14N, #24 — #30 J7W19N #26 — #30 #22 — #32 #24 — #32 #26 — #32 Layouts with 3A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 — D3M, E4M F7M, — #26 — G10M, K19M, — #28 — L22M — #30 — Layouts with 3A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 #28 — #26 #28 — #28 #28 C2M2N, — #24 #30 E4M4N, F4M8N G6M10N, — #26 #30 G6M12N, — #28 #30 K13M19N — #24 #32 — #26 #32 — #28 #32 Layouts with 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. B7N, C10N, — — #28 E19N, F22N, — — #30 G31N, H37N, — — #32 J44N 3 Amp Micro Twistpin Code 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket 100 200 300 Code 104 204 304 105 205 305 106 206 306 3 Amp Micro Socket Unshrouded Type A Insert 5 Amp #23 Pin .770 (19.56) .598 (15.19) Code 020 030 040 050 B D Code Code 004 005 006 C ØA øC Wire 024 034 044 025 035 045 026 036 046 1 Amp Nano Socket L Shell Size B C D E F G H J K L .025 (6.35) Shell, Receptacle ØA In 0.392 0.412 0.432 0.451 0.471 0.490 0.530 0.569 0.589 0.628 mm 9.96 10.46 10.97 11.46 11.96 12.45 13.46 14.45 14.96 15.95 In 0.392 0.412 0.432 0.451 0.471 0.490 0.530 0.569 0.589 0.628 Dimensions ØB mm 9.96 10.46 10.97 11.46 11.96 12.45 13.46 14.45 14.96 15.95 RECOMMENDED PANEL CUTOUT ØC In 0.283 0.305 0.324 0.344 0.364 0.383 0.419 0.459 0.478 0.518 mm 7.19 7.75 8.23 8.74 9.25 9.73 10.64 11.66 12.14 13.16 D Flats In mm 0.241 6.12 0.261 6.63 0.281 7.14 0.300 7.62 0.320 8.13 0.340 8.64 0.379 9.63 0.418 10.62 0.438 11.13 0.478 12.14 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® catalog Dimensions in Inches (millimeters) are subject to change without notice. 13 SERIES 881 Threaded Coupling 881-020R Rear Panel Mount, Right Angle PCB Receptacle Series 881 rear panel mount, threaded coupling, right angle receptacles are sealed with epoxy and meet IP67 requirements in mated condition. For open face sealing in an unmated condition request modification code -518. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. High performance crimp contacts are factory terminated to solid copper wire. SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are critical. How To Order C Shell Size and Insert Arrangements No. of Contacts Insert #23 Micro Nano Arrangements 5A. 3A. 1A. B7N — — 7 C10N — — 10 C2M2N — 2 2 D3M — 3 — D2W2N 2 — 2 E3W 3 — — E4M — 4 — E19N — — 19 E4M4N — 4 4 F4W 4 — — F7M — 7 — F22N — — 22 F4M8N — 4 8 F4W4N 4 — 4 G7W 7 — — G10M — 10 — G31N — — 31 G6M10N — 6 10 G6M12N — 6 12 H10W 10 — — H37N — — 37 H6W14N 6 — 14 J44N — — 44 J7W19N 7 — 19 K19M — 19 — K13M19N — 13 19 L22M — 22 — First letter of insert arrangement represents connector shell size, as in this example K13M19N NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 14 Sample Part Number 881-020R A Series 881-020R Insert Style A = Unshrouded Contacts B = Shrouded Contacts are recessed within the insulator Shell Size / Insert Arr.1 See Shell Size and Insert Arrangement Table Material/ Finish2 PCB Tail Finish Wire Type -B7N -M S -.125 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant S = Solder-dipped in IAW Sn63Pb37 G = Gold plated .080, .125, .175 MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 881-020RA-B7N-MS-.125-686A Plug Alternate Key Positions Suffix Code A° B° 686A 150° 210° 686B 75° 210° 686C 95° 230° 686D 140° 275° 686E 75° 275° 686F 95° 210° Master Key A° B° MOD-518 OPEN FACE SEALING For IP67 performance in open face (unmated) condition, use suffix -518. Example: 881-020RA-B7N-MS-.125-518 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 881 Threaded Coupling 881-020R Rear Panel Mount, Right Angle PCB Receptacle ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. Wire Code Table Layouts with 5A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — — E3W, F4W, #24 — — G7W, H10W #26 — — Layouts with 5A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. #22 — #28 #24 — #28 #26 — #28 — #30 D2W2N, F4W4N, #22 H6W14N, #24 — #30 J7W19N #26 — #30 #22 — #32 #24 — #32 #26 — #32 Layouts with 3A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 — D3M, E4M F7M, — #26 — G10M, K19M, — #28 — L22M — #30 — Layouts with 3A. and 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. — #24 #28 — #26 #28 — #28 #28 C2M2N, — #24 #30 E4M4N, F4M8N G6M10N, — #26 #30 G6M12N, — #28 #30 K13M19N — #24 #32 — #26 #32 — #28 #32 Layouts with 1A. Contacts Insert #23 Micro Nano Arrangement 5A. 3A. 1A. B7N, C10N, — — #28 E19N, F22N, — — #30 G31N, H37N, — — #32 J44N 3 Amp Micro Twistpin Code 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket 100 200 300 Code 104 204 304 105 205 305 106 206 306 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin C 45° Code 020 030 040 050 .025 (.635) ØA L .76 (19.30) B Code 024 034 044 025 035 045 026 036 046 Code 004 005 006 Shell Size B C D E F G H J K L .79 (20.07) A In. .392 .412 .431 .451 .471 .490 .530 .569 .589 .628 B mm. 9.96 10.46 10.95 11.46 11.96 12.45 13.46 14.45 14.96 15.95 In. .338 .358 .377 .397 .417 .436 .476 .515 .534 .574 Dimensions C mm. In. mm. 8.59 .260 6.60 9.09 .280 7.11 9.58 .300 7.62 10.08 .320 8.13 10.59 .340 8.64 11.07 .380 9.65 12.09 .400 10.16 13.08 .440 11.18 13.56 .460 11.68 14.58 .500 12.70 D Mnt Ø In. mm. .283 7.19 .305 7.75 .324 8.23 .344 8.74 .364 9.25 .383 9.73 .419 10.64 .459 11.66 .478 12.14 .518 13.16 E Flats In. mm. .241 6.12 .261 6.63 .281 7.14 .300 7.62 .320 8.13 .340 8.64 .379 9.63 .418 10.62 .438 11.13 .478 12.14 C E øD RECOMMENDED CUTOUT PANEL © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® catalog Dimensions in Inches (millimeters) are subject to change without notice. 15 SERIES 881 Threaded Coupling 881-018P Cable Plug, Solder Cup Series 881 threaded coupling, cable plug with solder cup contacts feature threadon rear adapters allowing access to solder cup contacts. Install cable shield braid directly to connector with Band-Master Micro band. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings, thermoplastic insulators. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where ruggedness and field repairability is required. C Shell Size and Insert Arrangements No. of Contacts Insert #23 Micro Nano Arrangements 5A. 3A. 1A. B7N — — 7 C10N — — 10 C2M2N — 2 2 D3M — 3 — D2W2N 2 — 2 E3W 3 — — E4M — 4 — E19N — — 19 E4M4N — 4 4 F4W 4 — — F7M — 7 — F22N — — 22 F4M8N — 4 8 F4W4N 4 — 4 G7W 7 — — G10M — 10 — G31N — — 31 G6M10N — 6 10 G6M12N — 6 12 H10W 10 — — H37N — — 37 H6W14N 6 — 14 J44N — — 44 J7W19N 7 — 19 K19M — 19 — K13M19N — 13 19 L22M — 22 — First letter of insert arrangement represents connector shell size, as in this example K13M19N How To Order Sample Part Number 881-018P A -B7N -M Series 881-018P Insert Style A = Unshrouded Contacts B = Shrouded Contacts are recessed within the insulator Shell Size / Insert Arr.1 See Shell Size and Insert Arrangement Table Material/ Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 881-018PA-B7N-M-686A Plug Alternate Key Positions Suffix Code A° B° 686A 150° 210° 686B 75° 210° 686C 95° 230° 686D 140° 275° 686E 75° 275° 686F 95° 210° Master Key B° A° SUITABLE WIRE RANGES 5A (#23) 22-28 AWG Wire Ranges 3A (Micro) 24-30 AWG 1A (Nano) 30-32 AWG NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 16 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 881 Threaded Coupling 881-018P Cable Plug, Solder Cup ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin C .856 (21.74) .540 (13.76) ØB ØA Band-Master™ Nano Band Platform Blue Stripe Dimensions Shell Size B C D E F G H J K L A Dia In 0.357 0.377 0.397 0.416 0.436 0.456 0.495 0.535 0.555 0.594 B Dia. mm 9.07 9.58 10.08 10.57 11.07 11.58 12.57 13.59 14.10 15.09 In 0.199 0.224 0.237 0.263 0.282 0.304 0.341 0.369 0.391 0.430 mm 5.05 5.69 6.02 6.68 7.16 7.72 8.66 9.37 9.93 10.92 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® catalog Dimensions in Inches (millimeters) are subject to change without notice. 17 SERIES 88 Threaded Coupling 881-029R Cable Receptacle, Solder Cup Series 881 threaded coupling cable receptacle with solder cup contacts for soldering to wires. Thread-on rear adapter allows access to contacts. Install cable shield braid directly to connector with Band-Master Micro band. Three contact sizes are available with current ratings of 5A, 3A and 1A. Aluminum or stainless steel housings and thermoplastic insulators. Ultraminiature SuperFly® connectors are ideal for soldier systems and other applications where reduced size and weight are a must. C Shell Size and Insert Arrangements No. of Contacts Insert #23 Micro Nano Arrangements 5A. 3A. 1A. B7N — — 7 C10N — — 10 C2M2N — 2 2 D3M — 3 — D2W2N 2 — 2 E3W 3 — — E4M — 4 — E19N — — 19 E4M4N — 4 4 F4W 4 — — F7M — 7 — F22N — — 22 F4M8N — 4 8 F4W4N 4 — 4 G7W 7 — — G10M — 10 — G31N — — 31 G6M10N — 6 10 G6M12N — 6 12 H10W 10 — — H37N — — 37 H6W14N 6 — 14 J44N — — 44 J7W19N 7 — 19 K19M — 19 — K13M19N — 13 19 L22M — 22 — First letter of insert arrangement represents connector shell size, as in this example K13M19N How To Order Sample Part Number 881-029R A -B7N -M Series 881-029R Insert Style A = Unshrouded Contacts B = Shrouded Contacts are recessed within the insulator Shell Size / Insert Arr.1 See Shell Size and Insert Arrangement Table Material/ Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 881-018RA-B7N-M-686A Plug Alternate Key Positions Suffix Code A° B° 686A 150° 210° 686B 75° 210° 686C 95° 230° 686D 140° 275° 686E 75° 275° 686F 95° 210° Master Key A° B° SUITABLE WIRE RANGES 5A (#23) 22-28 AWG Wire Ranges 3A (Micro) 24-30 AWG 1A (Nano) 30-32 AWG NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options 18 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 88 Threaded Coupling 881-029R Cable Receptacle, Solder Cup ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin 0.845 (21.46) C ø "A" 0.317 (8.05) ø "B" Band-Master™ Nano Band Platform Red Stripe Full Mate Indicator Dimensions Shell Size B C D E F G H J K L A Dia In 0.357 0.377 0.397 0.416 0.436 0.456 0.495 0.535 0.555 0.594 B Dia. mm 9.07 9.58 10.08 10.57 11.07 11.58 12.57 13.59 14.10 15.09 In 0.199 0.224 0.237 0.263 0.282 0.304 0.341 0.369 0.391 0.430 mm 5.05 5.69 6.02 6.68 7.16 7.72 8.66 9.37 9.93 10.92 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® catalog Dimensions in Inches (millimeters) are subject to change without notice. 19 SERIES 88 CORDSETS SuperFly® Cordsets High-performance, lightweight, overmolded cordsets for soldier system applications. G lenair Series 88 SuperFly® cordsets are the new standard for highspeed performance, ultraminiature interconnection systems. Our single-ended and back-to-back Series 88 SuperFly® cables offer three contact sizes, two coupling styles, twenty-seven contact arrangements. Standard jacket options include polyurethane and nylon braid. These lightweight, ultra-flexible cables are ideally suited for battlefield and other rugged applications where highspeed performance is essential. Glenair, Inc. 1211 Air Way Glendale, CA 91201-2497 818-247-6000 [email protected] www.glenair.com SERIES 886 SuperFly® Cordsets Product Selection Guide Quick Disconnect (QDC), SingleEnded and Back-to-Back Threaded Coupling, Single-Ended and Back-to-Back 886-021P 886-017P Single-Ended QDC Cable Plug with Nylon Overbraid Page 4 Page 10 Single-Ended QDC Cable Plug with Polyurethane Jacket Page 10 Single-Ended QDC Cable Receptacle with Nylon Overbraid Page 12 Single-Ended QDC Cable Receptacle with Polyurethane Jacket Page 12 Back-to-Back QDC Cordset with Nylon Overbraid Page 14 886-014 Page 18 Single-Ended Threaded Coupling Cable Receptacle with Nylon Overbraid Overmolded Cordset with “Cobra” Quick Disconnect 180° Entry Plug 886-016 Overmolded Cordset with “Cobra” Threaded Coupling 90° Page 20 Single-Ended Threaded Coupling Cable Receptacle with Polyurethane Jacket D Back-to-Back Threaded Coupling Cordset with Nylon Overbraid 880-029 880-027 Back-to-Back QDC Cordset with Polyurethane Jacket Page 8 Single-Ended Threaded Coupling Cable Plug with Polyurethane Jacket 880-028 880-0026 Page 8 Page 16 Overmolded Cordset with “Cobra” Quick Disconnect 90° Plug 886-024R 880-020R Page 6 886-025 886-023R 880-019R Page 6 Single-Ended Threaded Coupling Cable Plug with Nylon Overbraid 886-022P 886-018P Page 4 Single-Ended Low Profile “Cobra” Equipped Cordsets Page 14 Back-to-Back Threaded Coupling Cordset with Polyurethane Jacket © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 1 SERIES 886 SuperFly Single-Ended and Back-to-Back Cordsets ® S uperFly®overmolded quick-disconnect (QDC) or threaded coupling cordsets are now available as single-ended and back-to -back assemblies. Both have highly conductive nickel copper shield with 90 percent coverage. 5A contacts are terminated to #24AWG wire, 3A contacts are terminated to #26AWG wire, and 1A contacts are terminated to #30AWG Teflon wire. Color-coded wires. Two types of standard wire protection available: nylon overbraid for superior flexibility or abrasionresistant thermoplastic polyurethane. Both styles available with polyamide connector ove r m o l d. N i c k e l - p l a t e d a l u m i n u m a s s e m b l i e s a r e i d e a l fo r p ro t e c t e d environments where corrosion is not a problem. Non-reflective nickel-PTFE plated aluminum offers excellent conductivity, durability and corrosion resistance. Black zinc-nickel is preferred for soldier systems. 2 Product Specifications Contact (Size) Current Rating Wire Size Materials and Finishes 5 Amp (#23) 3 Amp (Micro) 1 Amp (Nano) 5A 3A 1A #22-28 AWG 500Vac #24-30 AWG 600Vac #28-32 AWG 250Vac DWV Contact 20 mΩ 32 mΩ 80 mΩ Resistance Insulation 200 megaohms minimum Resistance Temperature -30°C to +105°C Range Durability 2000 Mating Cycles Water IP67, MIL-STD-810 Method 512 Immersion, (1 meter, 1 hours) Mated Solvent Excellent resistance to most Resistance solvents, fuels and oils Vibration 37g Shock 300g Shielding >55dB minimum from 100 MHz Effectiveness to 1000MHz Property Insulator Shell 1A. Contact 3A. and 5A. Contact Encapsulant Wire Wire Insulation Overmold Cable shield Description Thermoplastic, glass-reinforced Aluminum or stainless steel. See ordering info. Precious metal alloy Copper alloy, 50 microinches gold over nickel finish Epoxy Silver-coated high-strength copper alloy Cross-linked fluoropolymer, color-coded per MIL-STD-681 (full color) Solvent-resistant polyamide Contact factory for material specifications Shield Coverage 90% minimum coverage Outer Jacket Nylon braid or extruded low smoke zero halogen thermoplastic polyurethane (TPU), black © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 886 SuperFly® Cordsets Single-Ended or Back-to-Back Cordsets with Braided or Polyurethane Jacket Single-Ended and Back-to-Back Waterproof in mated condition 100% electrically tested Nylon braid flexible to -50° C Rugged watertight construction Three contact sizes: 5A, 3A and 1A Nylon overbraid or TPU jacket Multi-branch complex cables also available ABOUT SUPERFLY®MATERIALS AND FINISHES Four standard material and finish options are available. 1 Aluminum shell with Electroless Nickel (EN). High reflectivity and poor corrosion resistance make nickel a poor choice for tactical systems, but nickel is preferred for avionics systems, space vehicles, medical equipment and test gear where corrosion is not a primary concern. Nickel is highly conductive and is excellent for EMI-protected systems. 4 Aluminum shell with Olive Drab or Cadmium (OD over Cad). excellent, corrosion resistance and excellent conductivity. Non-reflective OD over Cad is a primary choice for defense and aerospace applications. Inherently lubricious, resists galling. 2 Aluminum shell with Black Zinc-Nickel (Zn-Ni). Although less conductive than other finishes, non-reflective black Zn-Ni is a typical choice for soldier gear and is RoHS compliant. Corrosion resistance is good. 5 6 3 Aluminum shell with Electroless Nickel-PTFE (EN-PTFE). Excellent durability, corrosion resistance and conductivity. Nonreflective EN-PTFE is a primary choice for any harsh environment. Inherently lubricious, resists galling. 7 Stainless steel shell with Zinc-Cobalt (ZN-CO). Excellent durability, corrosion resistance and conductivity. Non-reflective black finish is an excellent choice for any harsh environment. Stainless steel, Passivated finish. Excellent corrosion resistance, good conductivity. A good choice for high corrosion areas where EMI shielding is not a primary concern. Suitable for most aerospace and tactical gear. Stainless steel, Ni-PTFE finish. Excellent corrosion resistance and excellent conductivity. A good choice for high corrosion areas where EMI shielding is a primary concern. Highly conductive, non-reflective Ni-PTFE finish is suitable for all aerospace and tactical systems. Material and Finish Comparison Data Property 1 2 3 4 5 6 7 Material and Finish Aluminum Electroless Nickel Aluminum Black ZincNickel Aluminum Electoless NickelPTFE Aluminum Olive Drab over Cadmium Stainless Steel Black ZincCobalt Stainless Steel Passivated Stainless Steel Electroless Nickel-PTFE M ZR MT NF ZC ZK ZMT Poor Good Excellent Very Good Excellent Excellent Excellent Yes Excellent Reflective $ Yes Good Non-reflective $$ Yes Excellent Non-reflective $$ No Excellent Non-reflective $$ No Excellent Non-reflective $$$$ Yes Good Reflective $$$$ Yes Excellent Non-reflective $$$$ Glenair Code Corrosion Resistance RoHS Compliance* Conductivity Reflectivity Cost * Meets DoD directives and European regulations for elimination of cadmium and hexavalent chromate. ABOUT SUPERFLY®CABLE JACKETS Standard SuperFly cable jackets include: extruded thermoplastic polyurethane (TPU) and nylon overbraid. TPU offers excellent all-round performance and is typically specified for military gear and oil exploration equipment. For soldier systems applications, nylon overbraid is an alternative to TPU jackets if weight and flexibility are of primary concern. Additional jacket and overmold materials are available for custom cordsets. Contact the factory for more information. Outer Jacket/Braid Comparison Data Property Flammability UL 94V-0 Temperature Range Flexibility Solvent Resistance Abrasion Resistance Toxicity TPU Jacket Flame-Retardent Yes -45°C to +150°C Good Excellent Excellent Low Smoke, Zero Halogen Nylon Overbraid Flame-Retardent No -50°C to +150°C Excellent Good Very Good Zero Halogen © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 3 SERIES 886 QDC CORDSET 886-017 and 886-018, Single-Ended Plug Cordset 886-017P AND 886-018 QDC PLUG CORDSET WITH NYLON OVERBRAID OR POLYURETHANE JACKET Overmolded Quick Disconnect plug cordsets feature abrasion resistant extruded polyurethane jackets or ultraflexible nylon overbraid. Polyamide overmold, tinned copper braid shield. High strength silver-coated copper alloy conductors, crosslinked ETFE insulation. Wire size depends on contact size. Several other cable types and overmold materials are available. Contact the factory for more information. How To Order Sample Part Number 886-017P Insert Style Shell Size and Insert Arrangement1 See Shell Size and Insert Arrangement Table Shell Material/Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZC = Stainless steel/black zinc cobalt Wire Length Indicated in inches; ex. 18 = 18 inches MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 886-017PA-B7N-M-18-686A Plug Alternate Key Positions D 4 -B7N -M -18 886-017P = QDC inline plug with shielded, nylon overbraid 886-018P = QDC inline plug with shielded, polyurethane jacket A = Unshrouded contacts B = Shrouded contacts are recessed within the insulator Series Suffix Code 686A 686B 686C 686D 686E 686F A A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° WIRE GAUGES PER CONTACT • 1A. contact (Nano) - 30 AWG • 3A. contact (Micro) - 26 AWG • 5A. contact (Size 23) - 24 AWG Master Key B° A° Glenair can also fulfill multi-branch cordset requests. Contact the factory to find out more about our capabilities. © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 886 QDC CORDSET 886-017 and 886-018, Single-Ended Plug Cordset ABOUT SHROUDED AND UNSHROUDED SUPERFLY®CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket Shell Size and Insert Arrangements Insert Arrangements B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M #23 5A. — — — — 2 3 — — — 4 — — — 4 7 — — — — 10 — 6 — 7 — — — No. of Contacts Micro Nano 3A. 1A. — 7 — 10 2 2 3 — — 2 — — 4 — — 19 4 4 — — 7 — — 22 4 8 — 4 — — 10 — — 31 6 10 6 12 — — — 37 — 14 — 44 — 19 19 — 13 19 22 — First letter of contact arrrangement represents connector shell size. As in this example K13M19N 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin ‘L’ +1.00/-.00 (+25.4/-.00) 2.30 (58.42) Max 886-017P 886-018P Plug Cordset Overmold ØB NOTES Dimensions Shell Size B C D E F G H J K L A Max OD In mm .325 8.26 .350 8.89 .365 9.27 .390 9.91 .410 10.41 .430 10.92 .470 11.94 .495 12.57 .520 13.21 .560 14.22 ØA B Max OD In mm .470 11.94 .495 12.57 .510 12.95 .535 13.59 .555 14.10 .575 14.61 .615 15.62 .640 16.26 .665 16.89 .700 17.78 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 5 D SERIES 886 QDC CORDSET 886-019 and 886-020, Single-Ended Receptacle Cordset 886-019R AND 886-020R QDC COUPLING WITH NYLON OVERBRAID OR POLYURETHANE JACKET Overmolded Quick Disconnect receptacle cordsets feature abrasion resistant extruded polyurethane jackets or ultraflexible nylon overbraid. Polyamide overmold, tinned copper braid shield. High strength silver-coated copper alloy conductors, crosslinked ETFE insulation. Wire size depends on contact size. Size #23 contacts have #24 AWG wire, 3 amp micropins have #26 AWG wire, and 1 amp nanopins have #30 AWG wire. How To Order Sample Part Number 886-019R Insert Style Shell Size and Insert Arrangement1 Shell Material/Finish M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant Wire Length 18 = 18 inches MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 886-019RA-B7N-M-18-686A Plug Alternate Key Positions 6 -M -18 See Shell Size and Insert Arrangement Table 2 D -B7N 886-019R = QDC inline receptacle with shielded, nylon overbraid 886-020R = QDC inline receptacle with shielded, polyurethane jacket A = Unshrouded contacts B = Shrouded contacts are recessed within the insulator Series Suffix Code 686A 686B 686C 686D 686E 686F A A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° Master Key A° B° WIRE GAUGES PER CONTACT • 1A. contact (Nano) - 30 AWG • 3A. contact (Micro) - 26 AWG • 5A. contact (Size 23) - 24 AWG Glenair can also fulfill multi-branch cordset requests. Contact the factory to find out more about our capabilities. © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 886 QDC CORDSET 886-019 and 886-020, Single-Ended Receptacle Cordset ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket Shell Size and Insert Arrangements Insert Arrangements B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M #23 5A. — — — — 2 3 — — — 4 — — — 4 7 — — — — 10 — 6 — 7 — — — No. of Contacts Micro Nano 3A. 1A. — 7 — 10 2 2 3 — — 2 — — 4 — — 19 4 4 — — 7 — — 22 4 8 — 4 — — 10 — — 31 6 10 6 12 — — — 37 — 14 — 44 — 19 19 — 13 19 22 — First letter of contact arrrangement represents connector shell size. As in this example K13M19N 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin ‘L’ +1.00/-.00 (+25.4/-.00) 2.30 (58.42) Max 886-019R 886-020R Receptacle Cordset Overmold ØB Dimensions Shell Size B C D E F G H J K L A Max OD In mm .325 8.26 .350 8.89 .365 9.27 .390 9.91 .410 10.41 .430 10.92 .470 11.94 .495 12.57 .520 13.21 .560 14.22 B Max OD In mm .470 11.94 .495 12.57 .510 12.95 .535 13.59 .555 14.10 .575 14.61 .615 15.62 .640 16.26 .665 16.89 .700 17.78 ØA NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 7 D SERIES 886 QDC CORDSET 886-026 and 886-027, Back-to-Back Cordset 886-026 AND 886-027 QDC COUPLING WITH NYLON OVERBRAID OR POLYURETHANE JACKET Overmolded quick disconnect back-to-back cordsets feature abrasion resistant extruded polyurethane jackets or ultraflexible nylon overbraid. Polyamide overmold, tinned copper braid shield. High strength silver-coated copper alloy conductors, crosslinked ETFE insulation. How To Order Sample Part Number Series First Side (P1) Second Side (P2) D 886-026 P Shell Size and Insert Arrangements A R B -B7N -MT -18 886-026 QDC, nylon overbraid, back-toback cordset 886-027 QDC, polyurethane jacketed, back-to-back cordset Gender P = Plug R = Receptacle Contact Type A = Unshrouded contacts B = Shrouded contacts are recessed within the insulator Gender P = Plug R = Receptacle Contact Type A = Unshrouded contacts B = Shrouded contacts are recessed within the insulator Shell Size and Insert Arr1 See shell size and insert arrangement table Shell Material/ Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/black zinc-nickel over electroless nickel MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant Wire Length 18 = 18 inches WIRE GAUGES PER CONTACT • 1A. contact (Nano) - 30 AWG • 3A. contact (Micro) - 26 AWG • 5A. contact (Size 23) - 24 AWG NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options Insert Arrangements B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M #23 5A. — — — — 2 3 — — — 4 — — — 4 7 — — — — 10 — 6 — 7 — — — No. of Contacts Micro Nano 3A. 1A. — 7 — 10 2 2 3 — — 2 — — 4 — — 19 4 4 — — 7 — — 22 4 8 — 4 — — 10 — — 31 6 10 6 12 — — — 37 — 14 — 44 — 19 19 — 13 19 22 — First letter of contact arrrangement represents connector shell size. As in this example K13M19N 8 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 886 QDC CORDSET 886-026 and 886-027, Back-to-Back Cordset ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 3 Amp Micro Socket 1 Amp Nano Twistpin 1 Amp Nano Socket 5 Amp #23 Socket 5 Amp #23 Pin Shrouded Type B Insert Unshrouded Type A Insert 2.30 (58.42) Max ØA ØB Nylon Braid or Polyurethane Jacket P1 ØB Dimensions Shell Size B C D E F G H J K L A Max OD In. mm. .345 8.76 .370 9.40 .380 9.65 .410 10.41 .430 10.92 .450 11.43 .485 12.32 .515 13.08 .535 13.59 .575 14.61 Overmold (2x) ' L ' + 1.00/.00 (25.4/.00) B Max OD In. mm. .470 11.94 .495 12.57 .510 12.95 .535 13.59 .555 14.10 .575 14.61 .615 15.62 .640 16.26 .665 16.89 .700 17.78 ØA P2 MOD-686 POLARIZING OPTIONS Standard Superfly connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 886-026PARB-B7N-MT-18-686A PLUG Master Key B° A° D Plug Alternate Key Positions Key Position A B C D E F Suffix Code 686A 686B 686C 686D 686E 686F A° B° 150° 75° 95° 140° 75° 95° 210° 210° 230° 275° 275° 210° RECEPTACLE Master Key A° B° © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 9 SERIES 886 Threaded Coupling Cordset 886-021 and 886-022 Single-Ended Plug Cordset 886-021 AND 886-022 THREADED PLUG WITH NYLON OVERBRAIDED OR POLYURETHANE JACKET Overmolded threaded plug cordsets feature abrasion resistant extruded polyurethane jackets or ultraflexible nylon overbraid. Polyamide overmold, tinned copper braid shield. High strength silver-coated copper alloy conductors, crosslinked ETFE insulation. Wire size depends on contact size. Size #23 contacts have #24 AWG wire, 3 amp micropins have #26 AWG wire, and 1 amp nanopins have #30 AWG wire. How To Order Sample Part Number 886-022R Series Insert Style Shell Size and Insert Arrangement1 Shell Material/Finish M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant Wire Length 18 = 18 inches MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 886-021RA-B7N-M-18-686A Plug Alternate Key Positions D 10 -B7N -M -18 See Shell Size and Insert Arrangement Table 2 Suffix Code 686A 686B 686C 686D 686E 686F A 886-021P = Threaded coupling plug with shielded, nylon overbraid 886-022P = Threaded coupling plug with shielded, polyurethane jacket A = Unshrouded contacts B = Shrouded contacts are recessed within the insulator A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° Master Key B° A° WIRE GAUGES PER CONTACT • 1A. contact (Nano) - 30 AWG • 3A. contact (Micro) - 26 AWG • 5A. contact (Size 23) - 24 AWG Glenair can also fulfill multi-branch cordset requests. Contact the factory to find out more about our capabilities. © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 886 Threaded Coupling Cordset 886-021 and 886-022 Single-Ended Plug Cordset ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 1 Amp Nano Twistpin Shrouded Type B Insert 5 Amp #23 Socket Shell Size and Insert Arrangements Insert Arrangements B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M #23 5A. — — — — 2 3 — — — 4 — — — 4 7 — — — — 10 — 6 — 7 — — — No. of Contacts Micro Nano 3A. 1A. — 7 — 10 2 2 3 — — 2 — — 4 — — 19 4 4 — — 7 — — 22 4 8 — 4 — — 10 — — 31 6 10 6 12 — — — 37 — 14 — 44 — 19 19 — 13 19 22 — First letter of contact arrrangement represents connector shell size. As in this example K13M19N 3 Amp Micro Socket Unshrouded Type A Insert 1 Amp Nano Socket 5 Amp #23 Pin 886-021P 886-022P Receptacle Cordset ‘L’ +1.00/-.00 (+25.4/-.00) 2.30 (58.42) Max Overmold ØB Dimensions Shell Size B C D E F G H J K L A Max OD In mm .365 9.27 .385 9.78 .405 10.29 .420 10.67 .440 11.18 .460 11.68 .500 12.70 .540 13.72 .560 14.22 .600 15.24 B Max OD In mm .470 11.9 .495 12.6 .510 13.0 .535 13.6 .555 14.1 .575 14.6 .615 15.6 .640 16.3 .665 16.9 .700 17.8 ØA Blue Indicator Stripe NOTES 1.See Section A for insert arrangement layouts and PCB footprints 2.See Section A for additional finish options © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 11 D SERIES 886 Threaded Coupling Cordset 886-023 and 886-024 Single-Ended Receptacle Cordset 886-023P AND 886-024P THREADED COUPLING RECEPTACLES WITH NYLON OVERBRAID OR POLYURETHANE JACKET Overmolded threaded receptacle cordsets feature abrasion resistant extruded polyurethane jackets or ultraflexible nylon overbraid. Polyamide overmold, tinned copper braid shield. High strength silver-coated copper alloy conductors, crosslinked ETFE insulation. Wire size depends on contact size. Size #23 contacts have #24 AWG wire, 3 amp micropins have #26 AWG wire, and 1 amp nanopins have #30 AWG wire. How To Order Sample Part Number 886-024P Insert Style Shell Size and Insert Arrangement1 Shell Material/Finish M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant Wire Length 18 = 18 inches MOD-686 POLARIZING OPTIONS Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 886-024PA-B7N-M-18-686A Plug Alternate Key Positions 12 -M -18 See Shell Size and Insert Arrangement Table 2 D -B7N 886-023R = Threaded coupling receptacle with shielded, nylon overbraid 886-024R = Threaded coupling receptacle with shielded, polyurethane jacket A = Unshrouded contacts B = Shrouded contacts are recessed within the insulator Series Suffix Code 686A 686B 686C 686D 686E 686F A A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° Master Key A° B° WIRE GAUGES PER CONTACT • 1A. contact (Nano) - 30 AWG • 3A. contact (Micro) - 26 AWG • 5A. contact (Size 23) - 24 AWG Glenair can also fulfill multi-branch cordset requests. Contact the factory to find out more about our capabilities. © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 886 Threaded Coupling Cordset 886-023 and 886-024 Single-Ended Receptacle Cordset ABOUT SHROUDED AND UNSHROUDED SUPERFLY® CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 3 Amp Micro Socket 1 Amp Nano Twistpin 1 Amp Nano Socket 5 Amp #23 Socket 5 Amp #23 Pin Figure 1 Figure 2 Shrouded Type B Insert Unshrouded Type A Insert Insert Arrangements B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M #23 5A. — — — — 2 3 — — — 4 — — — 4 7 — — — — 10 — 6 — 7 — — — No. of Contacts Micro Nano 3A. 1A. — 7 — 10 2 2 3 — — 2 — — 4 — — 19 4 4 — — 7 — — 22 4 8 — 4 — — 10 — — 31 6 10 6 12 — — — 37 — 14 — 44 — 19 19 — 13 19 22 — 886-023R 886-024R Plug Cordset ‘L’ +1.00/-.00 (+25.4/-.00) Shell Size and Insert Arrangements 2.30 (58.42) Max ØA Overmold Dimensions Shell Size B C D E F G H J K L A Max OD In mm .345 8.76 .370 9.40 .380 9.65 .410 10.41 .430 10.92 .450 11.43 .485 12.32 .515 13.08 .535 13.59 .575 14.61 Red Indicator Stripe ØB B Max OD In mm .470 11.9 .495 12.6 .510 13.0 .535 13.6 .555 14.1 .575 14.6 .615 15.6 .640 16.3 .665 16.9 .700 17.8 NOTES 1.See Section A for insert arrangement layouts and PCB footprints 2.See Section A for additional finish options D First letter of contact arrrangement represents connector shell size. As in this example K13M19N © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 13 SERIES 886 Threaded Coupling Cordset 886-028 and 886-029 Back-to-Back Cordset 886-028 BACK-TO-BACK, THREADED COUPLING WITH NYLON OVERBRAID OR POLYURETHANE JACKET Overmolded threaded coupling back-to-back cordsets feature abrasion resistant extruded polyurethane jackets or ultraflexible nylon overbraid. Polyamide overmold, tinned copper braid shield. High strength silver-coated copper alloy conductors, crosslinked ETFE insulation. How To Order Sample Part Number Series First Side (P1) Second Side (P2) D 886-028 P Shell Size and Insert Arrangements A R B -B7N -M -18 886-028 Threaded, nylon overbraid, back-to-back cordset 886-029 Threaded, polyurethane jacketed, back-to-back cordset Gender P = Plug R = Receptacle Contact Type A = Unshrouded contacts B = Shrouded contacts are recessed within the insulator Gender P = Plug R = Receptacle Contact Type A = Unshrouded contacts B = Shrouded contacts are recessed within the insulator Shell Size and Insert Arr1 See shell size and insert arrangement table Shell Material/ Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/black zinc-nickel over electroless nickel MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant Wire Length 18 = 18 inches WIRE GAUGES PER CONTACT • 1A. contact (Nano) - 30 AWG • 3A. contact (Micro) - 26 AWG • 5A. contact (Size 23) - 24 AWG NOTES 1.See Section A for insert arrangement layouts 2.See Section A for additional finish options Insert Arrangements B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M #23 5A. — — — — 2 3 — — — 4 — — — 4 7 — — — — 10 — 6 — 7 — — — No. of Contacts Micro Nano 3A. 1A. — 7 — 10 2 2 3 — — 2 — — 4 — — 19 4 4 — — 7 — — 22 4 8 — 4 — — 10 — — 31 6 10 6 12 — — — 37 — 14 — 44 — 19 19 — 13 19 22 — First letter of contact arrrangement represents connector shell size. As in this example K13M19N 14 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 886 Threaded Coupling Cordset 886-028 and 886-029 Back-to-Back Cordset ABOUT SHROUDED AND UNSHROUDED SUPERFLY®CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 3 Amp Micro Socket 1 Amp Nano Twistpin 1 Amp Nano Socket 5 Amp #23 Socket 5 Amp #23 Pin Shrouded Type B Insert ØA P1 Unshrouded Type A Insert Red Indicator Stripe Blue Indicator Stripe 2.30 (58.42) Max Nylon Braid or Polyurethane Jacket ØB ØB 2.30 (58.42) Max Overmold (2x) ØB ' L ' + 1.00/0.00 (25.4/0.00) Dimensions Shell Size A B C D E F G H J K L Dia. A In. mm. 0.336 8.53 0.356 9.04 0.375 9.53 0.395 10.03 0.415 10.54 0.434 11.02 0.454 11.53 0.493 12.52 0.533 13.54 0.553 14.05 0.592 15.04 Dia. B In. mm. 0.320 8.13 0.339 8.61 0.364 9.25 0.377 9.58 0.403 10.24 0.422 10.72 0.444 11.28 0.481 12.22 0.509 12.93 0.531 13.49 0.570 14.48 P2 MOD-686 POLARIZING OPTIONS Standard Superfly connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 886-027PARB-B7N-MT-18-686A PLUG Master Key B° A° D Plug Alternate Key Positions Key Position A B C D E F Suffix Code 686A 686B 686C 686D 686E 686F A° B° 150° 75° 95° 140° 75° 95° 210° 210° 230° 275° 275° 210° RECEPTACLE Master Key A° B° © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 15 SERIES 886 “Cobra” QDC Cordset 886-025 Single-Ended Overmolded “Cobra” Cordset with 90° Entry Plug 886-025 QUICK DISCONNECT “COBRA” PLUG WITH POLYURETHANE JACKET AND SHIELDED WIRE Polyurethane jacketed, Superfly® quick disconnect (QDC) single-ended cordsets with polyamide overmolded 90° “Cobra” plug. Three contact sizes are available, 5A, 3A and 1A. Aluminum or stainless steel housings, thermoplastic insulator, highstrength wire with crosslinked ETFE insulation. High performance crimp contacts, factory terminated to wires. Braided shield with 90% coverage. How To Order Sample Part Number 886-025P Series 886-025P Overmolded “Cobra” QDC Cordset with 90° Plug Insert Configuaration A = Unshrouded Contacts B = Shrouded Contacts Shell Size and Insert Arrangement1 See Shell Size and Insert Arrangement Table Shell Material/Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant NF = Aluminum/olive drab over cadmium ZC = Stainless steel/black zinc cobalt ZK = Stainless steel/passivate ZMT = Stainless steel/nickel-PTFE RoHS compliant Key Orientation 0°, 90°, 180°, 270° See figure 2 Wire Length 18 = 18 inches MOD-686 POLARIZING OPTIONS D -A Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 886-025P-A-B7N-MT-0-18-686A Plug Alternate Key Positions Suffix Code 686A 686B 686C 686D 686E 686F 16 A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° -B7N -MT -0 -18 WIRE GAUGES PER CONTACT • 1A. contact (Nano) - 30 AWG • 3A. contact (Micro) - 26 AWG • 5A. contact (Size 23) - 24 AWG Master Key B° A° © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 886 “Cobra” QDC Cordset 886-025 Single-Ended Overmolded “Cobra” Cordset with 90° Entry Plug ABOUT SHROUDED AND UNSHROUDED SUPERFLY®CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 3 Amp Micro Socket 1 Amp Nano Twistpin 1 Amp Nano Socket 5 Amp #23 Socket 5 Amp #23 Pin Unshrouded Type A Insert Shrouded Type B Insert Shell Size and Insert Arrangements Insert Arrangements B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M #23 5A. — — — — 2 3 — — — 4 — — — 4 7 — — — — 10 — 6 — 7 — — — No. of Contacts Micro Nano 3A. 1A. — 7 — 10 2 2 3 — — 2 — — 4 — — 19 4 4 — — 7 — — 22 4 8 — 4 — — 10 — — 31 6 10 6 12 — — — 37 — 14 — 44 — 19 19 — 13 19 22 — Figure 1 "L" +1.00/-0.00 (Length Per Part Number Development) 2.00 (50.8) Max P1 Master Key Location Figure 2: Master Key Orientation D 0° 90° 270° 180° First letter of contact arrrangement represents connector shell size. As in this example K13M19N © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 17 SERIES 886 “Cobra” QDC Cordset 886-014 Single-Ended Overmolded “Cobra” Cordset with 180° Entry Plug 886-014 QUICK DISCONNECT “COBRA” PLUG WITH POLYURETHANE JACKET AND SHIELDED WIRE Polyurethane jacketed, Superfly® quick disconnect (QDC) single-ended cordsets with polyamide overmolded 180° Cobra connector. Three contact sizes are available, 5A, 3A and 1A. Aluminum or stainless steel housings, thermoplastic insulator, highstrength wire with crosslinked ETFE insulation. High performance crimp contacts, factory terminated to wires. Braided shield with 90% coverage. How To Order Sample Part Number 886-014P Series 886-014P = Overmolded Cobra QDC cordset with 180° entry Plug Insert Configuaration A = Unshrouded Contacts B = Shrouded Contacts Shell Size and Insert Arrangement1 See Shell Size and Insert Arrangement Table Shell Material/Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant NF = Aluminum/olive drab over cadmium ZC = Stainless steel/black zinc cobalt ZK = Stainless steel/passivate ZMT = Stainless steel/nickel-PTFE RoHS compliant Master Key Location 0 thru 350° in 30° increments. See Master Key Location table Wire Length 18 = 18 inches MOD-686 POLARIZING OPTIONS D A Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 886-014PA-B7N-MT-0-18-686A Plug Alternate Key Positions Suffix Code 686A 686B 686C 686D 686E 686F 18 A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° -B7N -MT -06 -18 WIRE GAUGES PER CONTACT • 1A. contact (Nano) - 30 AWG • 3A. contact (Micro) - 26 AWG • 5A. contact (Size 23) - 24 AWG Master Key B° A° © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 886 “Cobra” QDC Cordset 886-014 Single-Ended Overmolded “Cobra” Cordset with 180° Entry Plug ABOUT SHROUDED AND UNSHROUDED SUPERFLY®CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 3 Amp Micro Socket 1 Amp Nano Twistpin 1 Amp Nano Socket 5 Amp #23 Socket 5 Amp #23 Pin Unshrouded Type A Insert Shrouded Type B Insert Shell Size and Insert Arrangements Insert Arrangements B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M #23 5A. — — — — 2 3 — — — 4 — — — 4 7 — — — — 10 — 6 — 7 — — — No. of Contacts Micro Nano 3A. 1A. — 7 — 10 2 2 3 — — 2 — — 4 — — 19 4 4 — — 7 — — 22 4 8 — 4 — — 10 — — 31 6 10 6 12 — — — 37 — 14 — 44 — 19 19 — 13 19 22 — First letter of contact arrrangement represents connector shell size. As in this example K13M19N 1.50 (38.1) A Overmold Polyamide A P1 Glenair connector interface IAW 880-001P Master Key Location per P/N Development Master Key Location No. 00 01 02 03 04 05 06 07 08 09 10 11 Degrees 0° 30° 60° 90° 120° 150° 180° 210° 240° 270° 300° 330° 0° B A Section A-A © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 19 D SERIES 886 “Cobra” Threaded Cordset 886-016 Single-Ended “Cobra” Threaded Coupling Cordset with 90° Entry Plug 886-016 QUICK DISCONNECT, 90° “COBRA” PLUG WITH POLYURETHANE JACKET AND SHIELDED WIRE Superfly® threaded coupling single-ended cordset with polyamide overmolded 90° “Cobra” plug. Three contact sizes are available, 5A, 3A and 1A. Aluminum or stainless steel housings, thermoplastic insulator, high-strength wire with crosslinked ETFE insulation. High performance crimp contacts, factory terminated to wires. Braided shield with 90% coverage. How To Order Sample Part Number 886-016P Series 886-016P = Overmolded threaded coupling “Cobra” Cordset with 90° Entry Plug Insert Configuaration A = Unshrouded Contacts B = Shrouded Contacts Shell Size and Insert Arrangement1 See Shell Size and Insert Arrangement Table Shell Material/Finish2 M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant NF = Aluminum/olive drab over cadmium ZC = Stainless steel/black zinc cobalt ZK = Stainless steel/passivate ZMT = Stainless steel/nickel-PTFE RoHS compliant Key Orientation 0 = 0° Wire Length Indicated in inches; ex. 18 = 18 inches 90 = 90° 180 = 180° Standard SuperFly® connectors have a single master key. Versions with three keys are also available if alternate key positions are required. Add suffix code 686 to the part number per the following example: 886-016P-A-B7N-MT-0-18-686A Plug Alternate Key Positions Suffix Code 686A 686B 686C 686D 686E 686F 20 A° 150° 75° 95° 140° 75° 95° B° 210° 210° 230° 275° 275° 210° -B7N -MT -0 -18 270 = 270° MOD-686 POLARIZING OPTIONS D A WIRE GAUGES PER CONTACT • 1A. contact (Nano) - 30 AWG • 3A. contact (Micro) - 26 AWG • 5A. contact (Size 23) - 24 AWG Master Key B° A° © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 886 “Cobra” Threaded Cordset 886-016 Single-Ended “Cobra” Threaded Coupling Cordset with 90° Entry Plug ABOUT SHROUDED AND UNSHROUDED SUPERFLY®CONFIGURATIONS Shrouded contacts are recessed within the insert. Unshrouded contacts extend from the insert face. Shrouded inserts contain 1 amp and 3 amp Twistpin contacts along with 5 amp socket contacts. Unshrouded inserts contain 1 amp and 3 amp sockets and 5 amp pin. 3 Amp Micro Twistpin 3 Amp Micro Socket 1 Amp Nano Twistpin 1 Amp Nano Socket 5 Amp #23 Socket 5 Amp #23 Pin Unshrouded Type A Insert Shrouded Type B Insert Shell Size and Insert Arrangements Insert Arrangements B7N C10N C2M2N D3M D2W2N E3W E4M E19N E4M4N F4W F7M F22N F4M8N F4W4N G7W G10M G31N G6M10N G6M12N H10W H37N H6W14N J44N J7W19N K19M K13M19N L22M #23 5A. — — — — 2 3 — — — 4 — — — 4 7 — — — — 10 — 6 — 7 — — — No. of Contacts Micro Nano 3A. 1A. — 7 — 10 2 2 3 — — 2 — — 4 — — 19 4 4 — — 7 — — 22 4 8 — 4 — — 10 — — 31 6 10 6 12 — — — 37 — 14 — 44 — 19 19 — 13 19 22 — Figure 1 "L" +1.00/-0.00 (+25.4/-0.00) (Length Per Part Number Development) 2.00 (50.8) Max P1 Master Key Location D Figure 2: Master Key Orientation 0° 90° 270° 180° First letter of contact arrrangement represents connector shell size. As in this example K13M19N © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 21 SERIES 88 ACCESSORIES AND TOOLS Covers, Boots and other Accessories For long term reliability and improved interconnect performance P rotect sensitive interconnect systems and cordsets from water ingress and debris aggregation with Glenair covers and heat shrink boots. Neoprene or metal covers for QDC and threaded coupling connectors. Neoprene covers are made from fungus-resistant neoprene per ASTM D 2000 BC610Z1. Attachment options: nylon rope for attachment to cable or stainless steel wire rope for attaching to panel with screw. Heatshrink boots provide strain relief and environmental protection. Shape-memory polymer returns to as-molded shape when heat is applied. A Semi-rigid high performance elastomer resists high temperature and withstands exposure to petroleum-based fluids and fuels. Also available with non-halogenated flame-retardant polyolefin for use where limited fire hazard is required. Glenair, Inc. 1211 Air Way Glendale, CA 91201-2497 818-247-6000 [email protected] www.glenair.com SERIES 88 Accessories and Tools Product Seletion Guide Accessories Tools 667-356R and 667-357P 600-192 Series 880 Plug and Receptacle Metal Covers for Series 880 QDC Connectors Page 2 Spanner Nut Tightening Tool Page 14 667-366R and 667-362P 600-202 Series 881 Metal Plug and Receptacle Covers for Series 881 Threaded Connectors Page 4 Spanner Tool for Front Panel Mount Jamnut Page 14 889-004P and 889-005R 601-108 Rubber Dust Covers for Series 881 QDC Plugs and Receptacles Page 6 BandMaster® ATS Nano Banding Tool and bands Page 15 889-006P and 889-007R Rubber Dust Covers for Series 881 Threaded Plugs and Receptacles Page 8 889-014R and 889-015R Page 10 Rear Panel Mount and Front Panel Mount Rubber Dust Covers for Series 880 and 881 Receptacle Connectors 770-031 Straight or Right Angle Heat Shrink Boot with W1 Adhesive Lining or Optional Adhesivies Page 12 E © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 1 SERIES 88 Accessories and Tools 667-356 Receptacle and 667-357 Plug, Metal Covers for Series 880 QDC Connectors METAL PROTECTIVE COVERS FOR SERIES 880 QUICK-DISCONNECT PLUGS AND RECEPTACLES Receptacle Cover Rugged metal protective covers fit 880 Series quickdisconnect (QDC) connectors.Protects connector from water and debris ingress. Three attachment options: nylon rope with lug termination (G-02 thru G-160) for attaching to panel, slip knot (GSCS) for attachment to cable or panel, and 1/32 inch stainless steel wire rope with loose crimp ferrule (SCF) for attaching to cable or to panel. Aluminum or stainless steel body. Plug Cover How To Order Sample Part Number Series Shell Material/Finish 667-357 M B G 70 -2 667-356 Receptacle, metal cover 667-357 Plug, metal cover M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant Shell Size See Dimensions Table for appropriate cover Attachment Type G = 1/16 inch diameter black nylon rope S = 1/32 inch diameter black nylon coated SST wire rope N = No Lanyard Attachment NB = No lanyard or attachment boss Termination Type See Attachment Termination table for code Attachment Length Lanyard length in inches (recommended length 2.0 inches) Omit with attachment type N, NB Materials and Finishes Cover Lanyard Crimp Ring, Attachment Ring and Crimp Ferrule Shrink Sleeve Aluminum alloy or stainless steel. See Ordering Info for material and finish options Black nylon rope .062" (1.57) diameter or 1/32" stainless steel rope with black nylon coating .034" (0.86) diameter Stainless steel with black oxide finish Polyolefin, black E 2 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 88 Accessories and Tools 667-356 Receptacle and 667-357 Plug, Metal Covers for Series 880 QDC Connectors Attachment Termination Termination Code Description Ø 1/16 Nylon Nylon Cord CordLanyard Lanyard(Style (Style“G”) “G”)Attachment: Attachment: -00 No Terminal -02 thru -160 -02 thru -160 See Table I See Table I Lug Termination Lug Termination Table I: Lug Termination Codes Style D Code Shrink Sleave C Ø.50 Ref Provides “slip Ø.50 -SCS2 Slip Crimp Sleeve knot “ adjustment Ref Slip Crimp -SCS may be crimped Provides “slip knot “ adjustment may be crimped for 2 Sleeve Length for permanent permanent attachment Determined at .50 Dia. attachment -CF3 Crimp Ferrule Supplied loose for field termination of lanyard -CF Crimp Ferrule3 Supplied loose for field termination of lanyard Ø 1/32 Stainless Steel Wire (Style “S”) Attachment: Ø 1/32 Stainless Steel Wire (Style “S”) Attachment: -00 No Terminal -003 No Terminal -CF Crimp Ferrule Supplied loose for field termination of lanyard -CF Crimp Ferrule3 Supplied loose for field termination of lanyard Receptacle Cover 667-356 Plug Cover 667-357 .700 (17.8) MAX .480 (12.2) MAX .700 (17.8) MAX .500 (12.7) MAX øA øB øG øF 00 02 04 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 SCS CF Ø C Max Ø D Max In mm In mm NO TERMINAL 0.093 (2.40) 0.310 (7.90) 0.121 (3.10) 0.310 (7.90) 0.242 (6.10) 0.362 (9.20) 0.262 (6.70) 0.382 (9.70) 0.282 (7.20) 0.402 (10.20) 0.302 (7.70) 0.422 (10.70) 0.321 (8.20) 0.441 (11.20) 0.341 (8.70) 0.461 (11.70) 0.361 (9.20) 0.481 (12.20) 0.380 (9.70) 0.500 (12.70) 0.400 (10.20) 0.520 (13.20) 0.420 (10.70) 0.540 (13.70) 0.439 (11.20) 0.559 (14.20) 0.459 (11.70) 0.579 (14.70) 0.478 (12.10) 0.598 (15.20) 0.498 (12.60) 0.618 (15.70) 0.518 (13.20) 0.638 (16.20) 0.538 (13.70) 0.658 (16.70) 0.557 (14.10) 0.677 (17.20) 0.577 (14.70) 0.697 (17.70) 0.597 (15.20) 0.717 (18.20) 0.617 (15.70) 0.737 (18.70) 0.637 (16.20) 0.757 (19.20) Slip/Crimp Sleeve Crimp Ferrule (Loose) NOTES 667-356 Dimensions Shell Size B C D E F G H J K L ØA In. 0.169 0.194 0.207 0.233 0.252 0.274 0.311 0.339 0.361 0.400 667-357 Dimensions ØB mm. 4.30 4.90 5.30 5.90 6.40 7.00 7.90 8.60 9.20 10.20 In. 0.417 0.442 0.455 0.481 0.500 0.522 0.559 0.587 0.609 0.648 mm. 10.60 11.20 11.60 12.20 12.70 13.30 14.20 14.90 15.50 16.50 Shell Size B C D E F G H J K L ØF In. 0.317 0.342 0.355 0.381 0.400 0.422 0.459 0.487 0.509 0.548 ØG mm. 8.10 8.70 9.00 9.70 10.20 10.70 11.70 12.40 12.90 13.90 In. 0.417 0.442 0.455 0.481 0.500 0.522 0.559 0.587 0.609 0.648 mm. 10.60 11.20 11.60 12.20 12.70 13.30 14.20 14.90 15.50 16.50 1.Attachment to withstand 25 lb pull test 2.Slip/crimp sleeve (SCS) - for Type G nylon cord only Provides “slip knot” adjustment, may be crimped for permanent attachment 3.Crimp ferrule (CF) - for Type S wire rope and G nylon cord Supplied loose for user termination © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. E 3 SERIES 88 Accessories and Tools 667-366 Receptacle and 667-362 Plug Covers for Series 881 Threaded Connectors METAL PROTECTIVE COVERS FOR SERIES 881 THREADED RECEPTACLES Rugged metal protective covers fit 881 Series threaded connectors. Protects connector from water and debris ingress. Three attachment options: nylon rope with lug termination (G-02 thru G-160) for attaching to panel, slip knot (GSCS) for attachment to cable or panel, 1/32 inch stainless steel wire rope with loose crimp ferrule (SCF) for attaching to cable or to panel. Aluminum or stainless steel body. Receptacle Cover Plug Cover How To Order Sample Part Number Series Shell Material/Finish 667-366 M B G 60 -3 667-366 = Receptacle, metal cover 667-362 = Plug, metal cover M = Aluminum/electroless nickel RoHS compliant ZR = Aluminum/zinc-nickel, non-reflective with RoHS compliant black chromate MT = Aluminum/nickel-PTFE RoHS compliant ZMT = Stainless steel/nickel-PTFE RoHS compliant Shell Size See Table I Attachment Type S = Ø 1/32 black nylon coated stainless wire rope G = Ø 1/16 Nylon rope black N = No attachment Termination Type See Attachment Termination table for code Attachment Length Lanyard length in inches (recommended length 2.0 inches) 667-366 RECEPTACLE COVER .70 (17.8) Max Master Key ØA Blue Indicator Stripe E 4 Shrink Sleeve Dimensions Shell Size B C D E F G H J K L ØA In. .355 .375 .395 .414 .434 .454 .493 .533 .553 .592 mm. 9.02 9.53 10.03 10.52 11.02 11.53 12.52 13.54 14.05 15.04 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 88 Accessories and Tools 667-366 Receptacle and 667-362 Plug Covers for Series 881 Threaded Connectors 667-362 PLUG COVER Master Keyway .70 (17.8) Max Dimensions O-ring ØA Red Indicator Stripe Shrink Sleeve Universal Slave Keyways Shell Size A B C D E F G H J K L ØA 0.318 0.337 0.362 0.375 0.401 0.420 0.442 0.479 0.507 0.529 0.568 8.10 8.60 9.20 9.50 10.20 10.70 11.20 12.20 12.90 13.40 14.40 SCS - SLIP/CRIMP SLEEVE For Nylon Rope (G) Only METAL PROTECTIVE COVERS FOR (See SERIES Table II) 881 THREADED RECEPTACLES See Note 4 Table I: Lug Termination Codes Code 00 02 04 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 SCS CF Attachment Termination Crimp Ferrule Length Termination Code Ø C Max Ø D Max Description Style Supplied Loose Determined In mm In mm Ø 1/16 Nylon Cord Lanyard (Style “G”) Attachment: At.50 Dia. NO TERMINAL -00 No Terminal Length To 0.093 (2.40) 0.310 (7.90) End D Of Wire Shrink Sleave Ø.50 -02 thru -160 0.121 (3.10) 0.310 (7.90) Lug Termination See Table Ref I 0.242 (6.10) 0.362 (9.20) C 0.262 (6.70) 0.382 (9.70) Provides “slip Ø.50 0.282 (7.20) 0.402 (10.20) knot “ adjustment Ref Slip/Crimp 0.302 (7.70) 0.422 (10.70) -SCS may be crimped 2 Sleeve 0.321 (8.20) 0.441 (11.20) Length for permanent Determined at .50 Dia. attachment 0.341 (8.70) 0.461 (11.70) 0.361 (9.20) 0.481 (12.20) -CF Crimp Ferrule3 Supplied loose for field termination of lanyard 0.380 (9.70) 0.500 (12.70) Ø 1/32 Stainless Steel Wire (Style “S”) Attachment: 0.400 (10.20) 0.520 (13.20) -00 No Terminal 0.420 (10.70) 0.540 (13.70) 0.439 (11.20) 0.559 (14.20) -CF Crimp Ferrule3 Supplied loose for field termination of lanyard 0.459 (11.70) 0.579 (14.70) 0.478 (12.10) 0.598 (15.20) Material/Finish: NOTES 0.498 (12.60) 0.618 (15.70) Al alloy or cres/see Cover 0.518 (13.20) 0.638 (16.20) Table II 1.Attachment to withstand 25 lb pull 0.538 (13.70) 0.658 (16.70) O-ring Fluorosilicone/N.A. test 0.557 (14.10) 0.677 (17.20) Attachment See Table II/N.A. 2.Slip/crimp sleeve (SCS) - for Type G 0.577 (14.70) 0.697 (17.70) Eyelet SST/black chromate nylon cord only 0.597 (15.20) 0.717 (18.20) Shrink sleeving polyolefin/N.A. Provides “slip knot” adjustment, 0.617 (15.70) 0.737 (18.70) copper/black may be crimped for permanent Crimp ring 0.637 (16.20) 0.757 (19.20) chromate attachment Slip/Crimp Sleeve SCS and CF for nylon copper/black 3.Crimp ferrule (CF) - for Type S wire Crimp Ferrule (Loose) cord chromate rope and G nylon cord CF for wire rope SST/passivated E Supplied loose for user termination © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 5 SERIES 881 Accessories and Tools 889-004 Plug & 889-005 Receptacle Dust Covers for Series 880 QDC Connectors 889-004 889-005 Fungus-resistant neoprene per ASTM D 2000 BC610Z1 Available for SuperFly QDC plugs and receptacles 889-004 Neoprene cover fits 881-001P, 886-017P AND 886-018P plugs with QDC coupling. 889-005 fits 881-002R, 886-0019R and 886-020R receptacles with QDC coupling. Protects connector from water and debris ingress. Flexible stainless steel lanyard is coated with abrasion-resistant black nylon. Supplied with lanyard and ring, or with loose crimp ferrule for field termination of lanyard. Field terminate by looping lanyard around cable, compress ferrule with flat nose pliers and remove excess lanyard. -55° to +120°C. Meets fungus resistance requirement of MIL-STD-810. How To Order Sample Part Number 889-004 -F Series Attach with ring or field terminate with loose crimp ferrule (-CF) 889-004 Rubber Cover for QDC Plug 889-005 Rubber Cover for QDC Receptacles Cover Size A thru L, See Dimensions Table Flexible, high strength 1/32 inch stainless steel lanyard with black nylon coating Attachment Type Omit = No attachment G = Ø1/16 black nylon cord S = Ø1/32 black nylon coated SST wire rope Attachment Length Length in inches, ±.25 inches Termination Type See Attachment Termination table for code Cover Material Omit = Standard C = Conductive Neoprene blend (conductance = 100K ohms/sq. minimum) Stainless steel attachment ring Copper alloy crimp ferrule with non-reflective black chromate over zinc finish 889-004 Dimensions G E 889-005 cover fits all QDC coupling receptacles 6 Dash no. -A -B -C -D -E -F -G -H -J -K -L C I.D. [.50(12.7) DEEP] I.D. [.53 (13.46) DEEP] O.D. O.D. I.D. in .13 .15 .18 .19 .22 .24 .26 .28 .31 .33 .37 -WS 889-005 Dimensions .80 (20.32) .80 (20.32) 889-004 cover fits all QDC coupling plugs 4 O.D. mm 3.19 3.68 4.41 4.66 5.39 5.88 6.37 6.86 7.60 8.09 9.07 in .40 .40 .45 .45 .45 .50 .50 .55 .55 .55 .60 mm 9.80 9.80 11.03 11.03 11.03 12.25 12.25 13.48 13.48 13.48 14.70 Dash no. -A -B -C -D -E -F -G -H -J -K -L I.D. 1 in .27 .29 .31 .33 .35 .37 .39 .43 .46 .48 .52 O.D. mm 6.62 7.11 7.60 8.09 8.58 9.07 9.56 10.54 11.27 11.76 12.74 in .50 .55 .55 .55 .60 .60 .65 .65 .70 .70 .75 mm 12.25 13.48 13.48 13.48 14.70 14.70 15.93 15.93 17.15 17.15 18.38 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 881 Accessories and Tools 889-004 Plug & 889-005 Receptacle Dust Covers for Series 880 QDC Connectors Table III: Solid Ring Attachment for SST Wire or Nylon Rope Attachment Termination Termination Code Description Ø 1/16 Nylon Cord Lanyard (Style “G”) Attachment: -00 No Terminal -01 thru -08 See Table I Lug Termination -SCS Slip Crimp Sleeve2 -WS With Strap -60 Thru -160 See Table III Solid Ring -CF Crimp Ferrule3 Style ØR Provides “slip knot “ adjustment may be crimped for permanent attachment Ø.50 Ref Length Determined at .50 Dia. 30° Supplied loose for field termination of lanyard Ø 1/32 Stainless Steel Wire (Style “S”) Attachment: -00 No Terminal Lug -11 thru -15 See Table II Lug Termination -60 thru -160 See Table III Solid Ring 30° -CF Crimp Ferrule3 Supplied loose for field termination of lanyard Dash No -60 -65 -70 -75 -80 -85 -90 -95 -100 -105 -110 -115 -120 -125 -130 -135 -140 -145 -150 -155 -160 ØT Ø R ±.005 In mm 0.244 6.20 0.264 6.71 0.284 7.21 0.304 7.72 0.323 8.20 0.343 8.71 0.363 9.22 0.382 9.70 0.402 10.21 0.422 10.72 0.441 11.20 0.461 11.71 0.480 12.19 0.500 12.70 0.520 13.21 0.540 13.72 0.559 14.20 0.579 14.71 0.599 15.21 0.619 15.72 0.639 16.23 Ø T ±.005 In mm 0.352 8.94 0.372 9.45 0.392 9.96 0.412 10.46 0.431 10.95 0.451 11.46 0.471 11.96 0.490 12.45 0.510 12.95 0.530 13.46 0.549 13.94 0.569 14.45 0.588 14.94 0.608 15.44 0.628 15.95 0.648 16.46 0.667 16.94 0.687 17.45 0.707 17.96 0.727 18.47 0.747 18.97 NOTES Table I: Lug Termination Attachment for Nylon Rope ØR Dash No -01 -02 -03 -04 -05 -06 -07 -08 Table II: Lug Termination Attachment for SST Wire Rope ØT Ø R ±.005 In mm .098 2.49 .126 3.20 .140 3.56 .145 3.68 .156 3.96 .167 4.24 .188 4.78 .197 5.00 ØV Ø T ±.005 In mm .30 7.62 .30 7.62 .30 7.62 .30 7.62 .30 7.62 .30 7.62 .30 7.62 .30 7.62 Dash No -11 -12 -13 -14 -15 ØW Ø V ±.005 In mm 0.093 2.36 0.119 3.02 0.145 3.68 0.167 4.24 0.197 5.00 Ø W ±.005 In mm 0.14 3.56 0.20 5.08 0.20 5.08 0.25 6.35 0.25 6.35 1.Attachment to withstand 25 lb pull test 2.Slip/crimp sleeve (SCS) - for Type G nylon cord only. Provides “slip knot” adjustment, may be crimped for permanent attachment 3.Crimp ferrule (CF) - for Type S wire rope and G nylon cord Supplied loose for user termination © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. E 7 SERIES 881 Accessories and Tools 889-006 Plug & 889-007 Receptacle Dust Covers for Series 881 Threaded Connectors 889-006 889-007 Fungus-resistant neoprene per ASTM D 2000 BC610Z1 Fits SuperFly plugs with threaded coupling Attach with ring or field terminate with loose crimp ferrule (-CF) Flexible, high strength 1/32 inch stainless steel lanyard with black nylon coating Stainless steel attachment ring 889-006 Neoprene cover fits 880-001P, 886-021P AND 886-022P plugs with threaded coupling. 889-007 fits 881-002R, 886-023R and 886-024R receptacles with threaded coupling Protects connector from debris ingress. Flexible stainless steel lanyard is coated with abrasion-resistant black nylon. Supplied with lanyard and ring, or with loose crimp ferrule for field termination of lanyard. Field terminate by looping lanyard around cable, compress ferrule with flat nose pliers and remove excess lanyard. -55° to +120°C. Meets fungus resistance requirement of MIL-STD-810. How To Order Sample Part Number 889-006 -F G 4 -02 C Series 889-006 Rubber Cover for Threaded Plug 889-007 Rubber Cover for Threaded Receptacles Cover Size A thru L, See Dimensions Table Attachment Type Omit = No attachment G = Ø1/16 black nylon cord S = Ø1/32 black nylon coated SST wire rope Attachment Length Length in inches, ±.25 inches Termination Type See Attachment Termination table for code Cover Material Omit = Standard C = Conductive Neoprene blend (conductance = 100K ohms/sq. minimum) Copper alloy crimp ferrule with non-reflective black chromate over zinc finish 889-006 Dimensions 889-007 Dimensions I.D. [.53 (13.46) DEEP] I.D.1 O.D. I.D.2 .80 (20.32) .25 (6.35) .23 (5.84) .80 (20.32) O.D. 889-006 cover fits all threaded coupling plugs E 889-007 cover fits all threaded coupling receptacles 8 Dash no. -A -B -C -D -E -F -G -H -J -K -L I.D. in .31 .33 .35 .37 .38 .40 .42 .46 .50 .52 .56 O.D. mm 7.87 8.38 8.89 9.40 9.65 10.16 10.67 11.68 12.70 13.21 14.22 in .55 .55 .60 .60 .65 .65 .65 .70 .75 .75 .80 mm 13.97 13.97 15.24 15.24 16.51 16.51 16.51 17.78 19.05 19.05 20.32 Dash no. -A -B -C -D -E -F -G -H -J -K -L I.D. 1 in mm .22 5.59 .24 6.10 .26 6.60 .28 7.11 .30 7.62 .32 8.13 .34 8.64 .38 9.65 .42 10.67 .44 11.18 .68 17.27 I.D. 2 in mm .28 7.11 .30 7.62 .32 8.13 .34 8.64 .36 9.14 .38 9.65 .40 10.16 .44 11.18 .48 12.19 .50 12.70 .54 13.72 in .50 .55 .55 .55 .60 .60 .65 .65 .70 .75 .75 O.D. mm 12.70 13.97 13.97 13.97 15.24 15.24 16.51 16.51 17.78 19.05 19.05 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 881 Accessories and Tools 889-006 Plug & 889-007 Receptacle Dust Covers for Series 881 Threaded Connectors Attachment Termination Termination Code Description Ø 1/16 Nylon Cord Lanyard (Style “G”) Attachment: -00 No Terminal -01 thru -08 See Table I Lug Termination Table III: Solid Ring Attachment for SST Wire or Nylon Rope Style ØR Shrink Sleave Provides “slip knot “ adjustment may be crimped for permanent attachment Ø.50 Ref -SCS Slip Crimp Sleeve2 -WS With Strap -60 Thru -160 See Table III Solid Ring -CF Crimp Ferrule3 ØT Length Determined at .50 Dia. 30° Supplied loose for field termination of lanyard Ø 1/32 Stainless Steel Wire (Style “S”) Attachment: -00 No Terminal Lug -11 thru -15 See Table II Lug Termination -60 thru -160 See Table III Solid Ring 30° -CF Crimp Ferrule3 Supplied loose for field termination of lanyard Dash No -60 -65 -70 -75 -80 -85 -90 -95 -100 -105 -110 -115 -120 -125 -130 -135 -140 -145 -150 -155 -160 Ø R ±.005 In mm 0.244 6.20 0.264 6.71 0.284 7.21 0.304 7.72 0.323 8.20 0.343 8.71 0.363 9.22 0.382 9.70 0.402 10.21 0.422 10.72 0.441 11.20 0.461 11.71 0.480 12.19 0.500 12.70 0.520 13.21 0.540 13.72 0.559 14.20 0.579 14.71 0.599 15.21 0.619 15.72 0.639 16.23 Ø T ±.005 In mm 0.352 8.94 0.372 9.45 0.392 9.96 0.412 10.46 0.431 10.95 0.451 11.46 0.471 11.96 0.490 12.45 0.510 12.95 0.530 13.46 0.549 13.94 0.569 14.45 0.588 14.94 0.608 15.44 0.628 15.95 0.648 16.46 0.667 16.94 0.687 17.45 0.707 17.96 0.727 18.47 0.747 18.97 NOTES Table I: Lug Termination Attachment for Nylon Rope ØR Dash No -01 -02 -03 -04 -05 -06 -07 -08 Table II: Lug Termination Attachment for SST Wire Rope ØT Ø R ±.005 In mm .098 2.49 .126 3.20 .140 3.56 .145 3.68 .156 3.96 .167 4.24 .188 4.78 .197 5.00 ØV Ø T ±.005 In mm .30 7.62 .30 7.62 .30 7.62 .30 7.62 .30 7.62 .30 7.62 .30 7.62 .30 7.62 Dash No -11 -12 -13 -14 -15 ØW Ø V ±.005 In mm 0.093 2.36 0.119 3.02 0.145 3.68 0.167 4.24 0.197 5.00 Ø W ±.005 In mm 0.14 3.56 0.20 5.08 0.20 5.08 0.25 6.35 0.25 6.35 1.Attachment to withstand 25 lb pull test 2.Slip/crimp sleeve (SCS) - for Type G nylon cord only provides “slip knot” adjustment, may be crimped for permanent attachment 3.Crimp ferrule (CF) - for Type S wire rope and G nylon cord Supplied loose for user termination © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. E 9 SERIES 881 Accessories and Tools 889-014 RPM & 889-015 FPM Rubber Dust Covers for Series 880 and 881 Receptacles Rubber protective dust covers for front and rear panel mount Series 88 connectors protect connectors from debris ingress. Two attachment cords available: 1/16 nylon rope or 1/32 inch stainless steel wire rope. Attachement options include: slip crimp sleave (SCS) for attaching to cable, lug termination (01-08) for attaching to panel with screw, solid ring (60-160) for installing under connector (rear panel mount only), with strap (WS) tie down looped through slip crimp sleave, and crimp ferrule (CF) for field termination. Attachment rings are stainless steel with black oxide finish. How To Order 889-014 Rear Panel Mount Receptacle Cover 889-015 Front Panel Receptacle Cover Sample Part Number 889-014 -F G Series 889-014 Rubber Cover for RPM Receptacles 889-015 Rubber Cover for FPM Receptacles Cover Size A thru L, See Dimensions Table Attachment Cord Omit = No attachment G = Ø1/16 black nylon cord S = Ø1/32 black nylon coated SST wire rope Attachment Length Length in inches, ±.25 inches Termination Type See Attachment Termination Table for code Cover Material Omit = Standard C = Conductive Neoprene blend (conductance = 100K ohms/sq. minimum) thru hole 4 -02 C Dimensions 889-014 Rear Panel Mount .35 (8.89) ØN ØP E 889-015 Cover Fits All QDC and Threaded Front Panel Mount Receptacles 10 Dash no. -A -B -C -D -E -F -G -H -J -K -L .35 (8.89) .31 (7.87) ØM 889-014 Cover Fits All QDC and Threaded Rear Panel Mount Receptacles 889-015 Front Panel Mount ØM ØN øP .06 (1.52) ØM in 0.16 0.18 0.20 0.21 0.24 0.26 0.28 0.32 0.35 0.37 0.41 .15 (3.81) .06 (1.52) ØN mm 4.06 4.57 5.08 5.33 6.10 6.60 7.11 8.13 8.89 9.40 10.41 in 0.34 0.36 0.38 0.40 0.42 0.44 0.46 0.50 0.54 0.56 0.60 ØP mm 8.64 9.14 9.65 10.16 10.67 11.18 11.68 12.70 13.72 14.22 15.24 in 0.25 0.25 0.28 0.28 0.31 0.31 0.38 0.38 0.44 0.44 0.50 mm 6.35 6.35 7.11 7.11 7.87 7.87 9.65 9.65 11.18 11.18 12.70 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 881 Accessories and Tools 889-014 RPM & 889-015 FPM Rubber Dust Covers for Series 880 and 881 Receptacles Attachment Termination Termination Code Description Ø 1/16 Nylon Cord Lanyard (Style “G”) Attachment: -00 No Terminal -01 thru -08 See Table I Lug Termination ØR Ø.50 Ref -SCS Slip Crimp Sleeve2 -WS With Strap -60 Thru -160 See Table III Solid Ring -CF Crimp Ferrule3 Table III: Solid Ring Attachment for SST Wire or Nylon Rope Style Length Determined at .50 Dia. Provides “slip knot “ adjustment may be crimped for permanent attachment 30° Supplied loose for field termination of lanyard Ø 1/32 Stainless Steel Wire (Style “S”) Attachment: -00 No Terminal Lug -11 thru -15 See Table II Lug Termination -60 thru -160 See Table III Solid Ring 30° -CF Crimp Ferrule3 Supplied loose for field termination of lanyard Dash No -60 -65 -70 -75 -80 -85 -90 -95 -100 -105 -110 -115 -120 -125 -130 -135 -140 -145 -150 -155 -160 ØT Ø R ±.005 In mm 0.244 6.20 0.264 6.71 0.284 7.21 0.304 7.72 0.323 8.20 0.343 8.71 0.363 9.22 0.382 9.70 0.402 10.21 0.422 10.72 0.441 11.20 0.461 11.71 0.480 12.19 0.500 12.70 0.520 13.21 0.540 13.72 0.559 14.20 0.579 14.71 0.599 15.21 0.619 15.72 0.639 16.23 Ø T ±.005 In mm 0.352 8.94 0.372 9.45 0.392 9.96 0.412 10.46 0.431 10.95 0.451 11.46 0.471 11.96 0.490 12.45 0.510 12.95 0.530 13.46 0.549 13.94 0.569 14.45 0.588 14.94 0.608 15.44 0.628 15.95 0.648 16.46 0.667 16.94 0.687 17.45 0.707 17.96 0.727 18.47 0.747 18.97 NOTES Table I: Lug Termination Attachment for Nylon Rope ØR Dash No -01 -02 -03 -04 -05 -06 -07 -08 Table II: Lug Termination Attachment for SST Wire Rope ØT Ø R ±.005 In mm .098 2.49 .126 3.20 .140 3.56 .145 3.68 .156 3.96 .167 4.24 .188 4.78 .197 5.00 ØV Ø T ±.005 In mm .30 7.62 .30 7.62 .30 7.62 .30 7.62 .30 7.62 .30 7.62 .30 7.62 .30 7.62 Dash No -11 -12 -13 -14 -15 ØW Ø V ±.005 In mm 0.093 2.36 0.119 3.02 0.145 3.68 0.167 4.24 0.197 5.00 Ø W ±.005 In mm 0.14 3.56 0.20 5.08 0.20 5.08 0.25 6.35 0.25 6.35 1.Attachment to withstand 25 lb pull test 2.Slip/crimp sleeve (SCS) - for Type G nylon cord only provides “slip knot” adjustment, may be crimped for permanent attachment 3.Crimp ferrule (CF) - for Type S wire rope and G nylon cord Supplied loose for user termination © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. E 11 SERIES 881 Accessories and Tools 770-031 Straight Heat Shrink Boot Angular Function Material Table III S = Straight Product Series and Basic Number 770-031 S 1 Boot Size Table I 02 Adhesive See Table II All Boots are Adhesive Lined (Standard is W1) W1 P ØCe ØAe ØAr ØCr R Ct At Fully Recovered As-Provided Expanded TABLE I: Boot Size and Shrink Boot Dimensions Boot Size Glenair US Part Marking (Engraved on Boot) Ae Min Dia Ar Max Dia At ± 10% Ce Min Dia Cr Max Dia Ct ± 10% P ± 10% R ± 10% 01 SF1 .370 (9.40) .160 (4.06) .040 (1.02) .180 (4.57) .045 (1.14) .030 (0.76) .533 (13.54) .183 (4.65) 02 SF2 .370 (9.40) .200 (5.08) .045 (1.14) .180 (4.57) .065 (1.65) .031 (0.79) .568 (14.43) .201 (5.11) 03 SF3 .560 (14.2) .260 (6.60) .050 (1.27) .370 (9.40) .100 (2.54) .035 (0.89) .600 (15.24) .205 (5.21) TABLE II: Glenair Series 77 Boots Adhesive Types W1 W2 R Attribute Standard High Temperature Hot Melt Adhesive Hot Melt Adhesive High Performance Epoxy Adhesive Boot Material Compatibility Continuous Operating Temp. Resistance to Fuels, Oils & Fluids Low Toxicity, Zero Halogen Type 1, 2, 5, 6 and 7 -55° to +125°C Good Yes Type 1, 2, 3 and 7 -40° to +80°C Good Yes Type 1, 2, 5 and 6 -75° to +150°C Excellent Yes TABLE III: Shrink Boot Materials E No. Compound Material Description 1 2025 High Performance Elastomer* 2 2010 Zero Halogen Polyolefin* Glenair SF1 C A Boots are marked with manufacturer's identification and part number * Other Materials available 12 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 881 Accessories and Tools 770-031 Right Angle Heat Shrink Boot Angular Function A = 90° Product Series and Basic Number 770-031 Material Table III A 1 Boot Size Table I 02 W1 Adhesive See Table II All Boots are Adhesive Lined (Standard is W1) G ØCr ØCe ØAe D Ct Fully Recovered As Received Expanded ØAr At TABLE I: Boot Size and Shrink Boot Dimensions Boot Size 01 02 03 Glenair US Part Marking (Engraved on Boot) SF1A SF2A SF3A Ae Min Dia Ar Max Dia At ± 10% Ce Min Dia Cr Max Dia Ct ± 10% G ± 10% D ± 10% .370 (9.40) .370 (9.40) .560 (14.2) .160 (4.06) .200 (5.08) .260 (6.60) .040 (1.02) .045 (1.14) .050 (1.27) .180 (4.57) .180 (4.57) .370 (9.40) .045 (1.14) .065 (1.65) .095 (2.41) .030 (0.76) .031 (0.79) .035 (0.89) .300 (7.62) .375 (9.53) .440 (11.20) .380 (9.65) .395 (10.0) .469 (11.9) TABLE II: Glenair Series 77 Boots Adhesive Types W1 Attribute Boot Material Compatibility Continuous Operating Temp. Resistance to Fuels, Oils & Fluids Low Toxicity, Zero Halogen W2 Hot Melt Adhesive High Performance Epoxy Adhesive Type 1, 2, 5, 6 and 7 -55° to +125°C Good Yes Type 1, 2, 3 and 7 -40° to +80°C Good Yes Type 1, 2, 5 and 6 -75° to +150°C Excellent Yes TABLE III: Shrink Boot Materials Material Description 1 2025 High Performance Elastomer* 2 2010 Zero Halogen Polyolefin* A G Compound C SF1A No. * Other Materials available R Standard High Temperature Hot Melt Adhesive E Boots are marked with manufacturer's identification and part number © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 13 SERIES 88 Accessories and Tools 600-192 Spanner Nut and 600-202 Spanner Tool 600-192 SPANNER NUT TIGHTENING TOOL Spanner nut tool fits front panel mount or rear panel mount jam nuts. Heat-treated steel, nickel plated. Shell Size Spanner Tool Part Number B C D E F G H J K L 600-192-B 600-192-C 600-192-D 600-192-E 600-192-F 600-192-G 600-192-H 600-192-J 600-192-K 600-192-L 1.050 (26.67) MAX øA ØA In. mm. .412 .432 .451 .471 .491 .510 .549 .589 .608 .648 10.46 10.97 11.46 11.96 12.47 12.95 13.94 14.96 15.44 16.46 Drive Square Recommended Torque (In-Lbs.) Min Max 3/16" 3/16" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 3/8" 8 13 13 13 16 16 20 20 20 23 13 18 18 18 21 21 25 25 25 28 600-202 SPANNER TOOL FOR FRONT PANEL MOUNT JAMNUT Spanner Tool Tool Part Size Number 1/4" DRIVE .250 (6.35) .250 (6.35) E 600-202-B 600-202-C 600-202-D 600-202-E 600-202-F 600-202-G 600-202-H 600-202-J 600-202-K 600-202-L In. mm. In. mm. Jam Nut Thd Size Reference 0.572 0.590 0.610 0.629 0.647 0.667 0.705 0.745 0.763 0.803 14.53 14.99 15.49 15.98 16.43 16.94 17.91 18.92 19.38 20.40 0.332 0.350 0.370 0.389 0.407 0.427 0.465 0.505 0.523 0.563 8.43 8.89 9.40 9.88 10.34 10.85 11.81 12.83 13.28 14.30 M7.0 M7.5 M8.0 M8.5 M9.0 M9.5 M10.5 M11.5 M12.0 M13.0 ØA ØB 3X .088 (3x 2.24) øA øB Recommended Torque Value in Lbs Min Max 8 13 13 13 16 16 20 20 20 23 13 18 18 18 21 21 25 25 25 28 Spanner nut tool fits front panel mount jam nuts. Alloy steel, nickel plated. GLENAIR ø.500 (12.7) B C D E F G H J K L Dimensions 1.000 (25.4) 2X .088 (2.24) 2X 45° 90° 14 © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 88 Accessories and Tools 601-108 Band-Master™ ATS Nano Banding Tool 601-108BAND-MASTER™ ATS NANO BANDING TOOL Fast, cost-effective shield termination. Attach cable shields to SuperFly connectors with Band-Master™ ATS stainless steel straps. The Band-Master™ ATS system offers fast termination and the flexibility to handle a wide range of parts with just one band size. Approved for aerospace and defense, these straps have successfully passed rigorous shock, vibration and environmental testing. 1 1 The 601-108 Nano Band-Master™ ATS Tool weighs 1.18 lbs., and is designed for nano flat .075" width clamping bands (601-500, 601504 and 601-508) in a tension range from 20 to 50 lbs. Calibrate at 50 lbs. ± 3 lbs. for most shield terminations. Tool and band should never be lubricated. 2 2 Short (6"), Medium (9") or Long (14") Nano Bands are provided flat or pre-coiled. Nano bands are designed for use with the 601-108 Band-Master™ ATS hand banding tool. Bands should always be double wrapped. Precision engineered from 300 Series SST. Figure Description Part Number 1 Nano Band Installation Tool 600-108 Figure 2 Length in. mm. 6.0 9.0 14.0 152.4 228.6 355.6 Part Number Flat Pre-Coiled 601-500 601-504 601-508 601-501 601-505 601-509 Acommodates Diameter in. mm. .60 .94 1.8 15.2 23.9 45.7 Tail Length Indicator Mark .124 (3.1) Ref. Contact Glenair or visit our website (glenair.com) to view our complete line of BAND-MASTER® products, including pneumatic tools for high volume production and calibration kits. .075 (1.9) Ref. 6.0 ± .030 (152.4 ± 0.8) .090 (2.3) Ref. .038 (0.9) Ref. .009 (0.2) Ref. E © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 15 SERIES 88 SuperFly® to Alphalink™ Flex Jumpers Recommended Connector Pairs SERIES 171 AlphaLink SL Flex Jumpers ® The easiest and fastest way to incorporate flexible circuit cabling in your highperformance application Glenair AlphaLink® SL I/O-to-board jumper assemblies are cataloged according to I/O connector type. Glenair currently offers six families of AlphaLink® jumpers for Series 801 and 804 Mighty Mouse, Series 79 Micro-Crimp, MIL-DTL-83513 Micro-D, Series 89 Nanominiature circular and rectangular, and our ultraminiature Series 88 SuperFly®. Flex-to-board solutions available in each family are designed to optimize weight and package size reduction as well as maintain electrical performance equivalent with I/O connector performance*. Solderless connection allows fast yet rugged PC board mating Easy ordering of highperformance I/O connector-toboard flex jumpers Ideal for rapid prototyping * Contacts mapped 1-to-1 from I/O to B/L connector (unused B/L contacts not connected). For alternative wire schedules, please consult factory. Chemically etched, copper-clad Designed for optimal electrical polyimide flex circuits offer performance, including matchedexcellent temperature tolerance, impedance applications dimensional stability, and reduced size and weight Superior electrical and mechanical performance compared to other A high-availability, fast-turn cabling options catalog solution 880-034 AND 881-021 DIMENSIONS I/O Connector Dimensions Shell Size A B C D E F G H J K L E 16 ØA In 0.372 0.392 0.412 0.432 0.451 0.471 0.490 0.530 0.569 0.589 0.628 mm 9.45 9.96 10.46 10.97 11.46 11.96 12.45 13.46 14.45 14.96 15.95 ØB In 0.265 0.283 0.305 0.324 0.344 0.364 0.383 0.419 0.459 0.478 0.518 mm 6.73 7.19 7.75 8.23 8.74 9.25 9.73 10.64 11.66 12.14 13.16 C Flats In mm 0.222 5.64 0.241 6.12 0.261 6.63 0.281 7.14 0.300 7.62 0.320 8.13 0.340 8.64 0.379 9.63 0.418 10.62 0.438 11.13 0.478 12.14 B/L Connector Dimensions Layout 4 8 10 16 20 28 32 40 AA In 0.527 0.627 0.677 0.827 0.927 1.127 1.277 1.427 BB mm 13.39 15.93 17.20 21.01 23.55 28.63 32.44 36.25 In 0.350 0.450 0.500 0.650 0.750 0.950 1.100 1.250 C mm 8.89 11.43 12.7 16.51 19.05 24.13 27.94 31.75 ØB I/O Connector Recommended Cutout BB .150 .050 .050 Typ Ø.042 Typ. Pads 1 10 11 20 .025 2x Ø.080 Mounting Holes B/L Recommended PCB Layout © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. SERIES 88 SuperFly® to Alphalink™ Flex Jumpers Recommended Connector Pairs How To Order 880-034 .69 Max .35 Max ØA Sample Part Number Series I/O Insert Configuration Pos 1 BB .183 AA Ø.021/.017 Typ .258 B/L .032 ±.015 Typ Alpha Link SLC A -B7N -M -2 T -6 S T -6 S 880-034R = Series 88 SuperFly QDC I/O receptacle to Series 171 AlphaLink® SL A = Unshrouded contacts (e.g. Nano socket) B = Shrouded contacts (e.g. Nano TwistPin) I/O L ±.05 880-034R I/O Shell Size / Insert Arrangement.1 B7N, C10N, E19N, F22N, G31N, H37N, J44N See section A all insert arrangements avail. I/O Shell Material/Finish See Table I AlphaLink® Finish 2 = Nickel 5 = Gold AlphaLink® Hardware Option T = Threaded thru hole Omit for thru hole Assembly Length (L) 3 = 3.00 ± .05 In 6 = 6.00 ± .05 In 12 = 12.00 ± .05 In Optional Shielding S = With shielding Omit for none How To Order 880-034 .800 Max .610 Max Sample Part Number ØA I/O I/O Insert Configuration L ±.05 -2 I/O Shell Material/Finish See Table I AlphaLink® Finish 2 = Nickel 5 = Gold .183 AlphaLink® Hardware Option T = Threaded thru hole Omit = for thru hole .032 ±.015 Typ Assembly Length (L) 3 = 3.00 ± .05 In 6 = 6.00 ± .05 In 12 = 12.00 ± .05 In Optional Shielding S = With shielding Omit for none Ø.021/.017 Typ Alpha Link SLC -M B7N, C10N, E19N, F22N, G31N, H37N, J44N See section A all insert arrangements avail. BB .258 -B7N I/O Shell Size / Insert Arrangement.1 Pos 1 B/L A 881-021R = Series 88 SuperFly QDC I/O receptacle to Series 171 AlphaLink® SL A = Unshrouded contacts (e.g. Nano socket) B = Shrouded contacts (e.g. Nano TwistPin) Series AA 881-021R RECOMMENDED SUPERFLY I/O TO ALPHALINK INSERT ARRANGEMENTS To optimize the 40-contact AlphaLink board level connector, 40 contacts of a 44-contact size SuperFly connector can be used. 1 1 2 1 5 3 6 7 2 3 5 6 8 2 30 31 B7N C10N E19N 4 1 5 1 8 5 10 6 8 Contacts 10 Contacts F22N 1 11 10 20 20 Contacts 4 1 5 10 16 23 29 34 7 13 18 24 29 3 8 14 19 25 4 9 13 18 22 5 10 14 19 7 12 16 19 4 8 13 17 10 9 1 3 1 G31N 9 15 22 28 33 37 H37N 14 1 16 1 20 28 15 32 17 40 28 Contacts 32 Contacts 1 6 12 19 27 34 40 5 11 18 26 33 39 44 E J44N 1 21 40 Contacts © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. 17 SMALL, LIGHTWEIGHT CONNECTORS AND CABLES Mission-critical interconnect technologies with proven defense industry pedigree and performance Field and factory tested, Glenair’s range of ultraminiature connectors and cables have become the gold standard for warfighter applications. Today’s combat environment demands total reliability from every electronic component—from soldier-wearable devices to eye-in-thesky UAV payloads. Interconnect technologies—contacts, connectors, shields, jackets, cables and more—are no exception. Our warfighters deserve highly-engineered, reliable systems that contribute to mission success without adding burdensome size and weight. SuperFly™ The ultimate ultraminiature tactical connector for high-speed applications SuperJack™ The ultra harsh-environment unipole connector for audio, data, and power HiPer 55116 Advanced-performance audio frequency JTRS radio connectors and cables 18 MouseBud™ The low-profile, snap-lock, trigger-release connector for wearable soldier systems SuperSeal™ RJ45 and USB connectors for harsh environmental applications Mighty Mouse Cobra The compact EMI/RFI plug assembly for low-profile, reduced space applications Mighty Mouse The industry standard ultraminiature push-pull soldier interconnect Mighty Mouse 824 The high-performance locking push-pull connector for tactical soldier applications Turnkey Cable Assemblies All Glenair connector technologies are available wired, tested and ready for immediate use © 2015 Glenair, Inc • 1211 Air Way, Glendale, CA 91201 • 818-247-6000 • www.glenair.com • U.S. CAGE code 06324 • Series 88 SuperFly® Catalog Dimensions in Inches (millimeters) are subject to change without notice. U.S. Army photo by Staff Sgt. Adam Mancini Don’t see it in our catalog? Just ask. Unusual small-quantity requests are our specialty. Plus, popular part numbers are available for immediate, sameday shipment with no dollar or quantity minimums. WHY CHOOSE Glenair? O Custuo tstandin mer S g ervice ! aterials! Raw M lenty of P sembly! In-House As Abundant Machining Capacity! Huge “ Same- Day” In ventory ! Glenair, Inc. 1211 Air Way Glendale, CA 91201-2497 818-247-6000 [email protected] www.glenair.com Ou t o f T h i s Wo r l d INTERCONNECT SOLUTIONS Glenair, Inc. 1211 Air Way • Glendale, California • 91201-2497 Telephone: 818-247-6000 • Fax: 818-500-9912 • [email protected] www.glenair.com Glenair Power Products Group 860 N. Main Street Extension Wallingford, CT 06492 Glenair Microway Systems 7000 North Lawndale Avenue Lincolnwood, IL 60712 Telephone: 203-741-1115 Facsimile: 203-741-0053 [email protected] Glenair UK Ltd 40 Lower Oakham Way Oakham Business Park P.O. Box 37, Mansfield Notts, NG18 5BY England Telephone: +44-1623-638100 Facsimile: +44-1623-638111 [email protected] Telephone: 847-679-8833 Facsimile: 847-679-8849 Glenair Nordic AB Gustav III : S Boulevard 46 SE-169 27 Solna Sweden Telephone: +46-8-50550000 [email protected] Glenair Electric GmbH Schaberweg 28 61348 Bad Homburg Germany Telephone: 06172 / 68 16 0 Facsimile: 06172 / 68 16 90 [email protected] Glenair Iberica C/ La Vega, 16 45612 Velada Spain Glenair Italia S.p.A. Via Del Lavoro, 7 40057 Quarto Inferiore – Granarolo dell’Emilia Bologna, Italy Telephone: +39-051-782811 Facsimile: +39-051-782259 [email protected] Glenair France SARL 7, Avenue Parmentier Immeuble Central Parc #2 31200 Toulouse France Glenair Korea B-1304 Gunpo IT Valley 148 Gosan-Ro, Gunpo-Si Kyunggi-Do, Korea 435-733 Telephone: +82-31-8068-1090 Facsimile: +82-31-8068-1092 [email protected] © 2015 Glenair, Inc. Printed in U.S.A. Telephone: +34-925-89-29-88 Facsimile: +34-925-89-29-87 [email protected] Telephone: +33-5-34-40-97-40 Facsimile: +33-5-61-47-86-10 [email protected] SERIES 88 SUPERFLY ® ULTRAMINIATURE CONNECTORS AND CORDSETS