Series 79 General Information Series 79 Micro-Crimp General Information Performance Specifications DESCRIPTION C DETAILED PERFORMANCE SPECIFICATIONS REQUIREMENT PROCEDURE Dielectric Withstanding Voltage No breakdown or flashover EIA-364-20 IEC-60512-4-1 Sea level AC rms 50 or 60 Hz. One minute dwell. #23 contacts 500 volts #16 contacts 1800 volts #12 contacts 1800 volts Current Carrying Capacity EIA-364-70 Method 1 IEC-60512-5 Test 9b Shell-to-shell Resistance (connectors with ground springs) 2.5 millivolt drop maximum Shielding Effectiveness Contact Size 12 16 23 Max Current 23 13 5 >75 dB attenuation from 100 MHz to 1000MHz, >60dB 1GHz to 4GHz, >40dB 4GHz to 10GHz. EIA-364-83 IEC-60512-2-6 Electroless nickel plated connectors. EIA-364-66 IEC-60512-23-3 Water Immersion No evidence of water penetration into mated connectors. No evidence of water penetration into an unmated panel mounted PCB receptacle. ≥ 100 MΩ insulation resistance. MIL-STD-810F Method 512.4 1 meter immersion 1 hour Ingress Protection IP67 rating IEC-60529 Vibration, Sine No discontinuity of greater than 1 microseconds, no cracking, breaking or loosening of parts, plug shall not become disengaged from receptacle. Connectors shall meet electrical requirements after vibration test. EIA-364-28 Test Condition IV IEC-60512-6-4 100 milliamp test current 10- 2,000 Hz 20 g, 196 m/s2 Vibration, Random No discontinuity of greater than 1 microseconds, no cracking, breaking or loosening of parts, plug shall not become disengaged from receptacle. Connectors shall meet electrical requirements after vibration test. EIA-364-28 Test Condition VI Letter J IEC-60512-6-4 100 milliamp test current 50- 2,000 Hz 43.92 g rms Dimensions in Inches (millimeters) are subject to change without notice. © 2011 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: [email protected] C-6 Series 79 General Information Series 79 Micro-Crimp General Information Performance Specifications DESCRIPTION DETAILED PERFORMANCE SPECIFICATIONS REQUIREMENT PROCEDURE Mechanical Shock No discontinuity of greater than 1 microsecond, no cracking, breaking or loosening of parts, plug shall not become disengaged from receptacle. Connectors shall meet electrical requirements after shock test. EIA-364-27 Condition D IEC-60512-6-3 3 shocks X 3 axes X 2 directions = 18 shocks 2941 m/s2 (300 g’s), 3 ms, halfsine Thermal Shock No mechanical damage or loosening of parts. Following thermal shock, connector shall meet contact resistance, DWV, insulation resistance and shell-to-shell resistance requirements. EIA-364-32 Test Condition IV IEC-60512-11-4 5 cycles consisting of -65° C 30 minutes, +25° C 5 minutes max., +150° C 30 minutes, +25° C 5 minutes max. Humidity, Cyclic (Damp Heat, Cyclic) (Moisture Resistance) No deterioration which will adversely affect the connector. 100 megohms minimum insulation resistance during the final cycle. Following the recovery period, connectors shall meet contact resistance, shell-to-shell resistance and DWV requirements. EIA-364-31 Condition B Method III IEC-60512-11-12 80-98% RH 10 cycles (10 days) +25° C to +65° C Step 7b vibration deleted. 24 hour recovery period. Mechanical Durability, at Ambient Temperature No deterioration which will adversely affect the connector after 2000 cycles of mating and unmating. Connectors shall meet contact resistance, insulation resistance, shell-to-shell resistance, DWV, and mating and unmating force. EIA-364-09 IEC-60512-5 Test 9a Corrosion (Salt Mist) Unmated connectors shall show no lifting of plated coating or exposure of basis material under power (3X) magnification which adversely effects DWV and contact resistance performance when evaluated. EIA-364-26 IEC 60512-11-6 5% salt solution 35° C Unmated connectors Code MT: Ni-PTFE 500 hours Code M: electroless nickel 48 hours Code NF: Cadmium 500 hours Code ZNU: Black zinc nickel 500 hours Solderability, PC Tail Contacts 95% solder coverage. Smooth, bright and even finish. EIA-364-52 Category 3 IEC-60512-12-1 IEC-68-2-20 Test Ta, method 1 8 hours steam aging prior to test 245° C 4-5 sec. dwell 10X magnification Dimensions in Inches (millimeters) are subject to change without notice. © 2011 Glenair, Inc. U.S. CAGE Code 06324 Rev. 10-2-14 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 E-Mail: [email protected] C-7 www.glenair.com C Series 79 General Information Series 79 Micro-Crimp General Information Performance Specifications DESCRIPTION C DETAILED PERFORMANCE SPECIFICATIONS REQUIREMENT PROCEDURE Resistance To Soldering Heat No damage to connector. Connectors shall meet insulation resistance and waterproof sealing requirements. EIA-364-56 IEC-60512-12-5 Test 12e 260° C, 10 seconds (PC tail) Impact, Cable Connectors No impairment of function. Connector shall meet contact resistance, insulation resistance and waterproof sealing. EIA-364-42 IEC-60512-5 test 7b 1 meter 8 drops Fluid Immersion No damage from immersion in various fuels and oils. Connector shall meet mating/unmating force and dielectric withstanding voltage. EIA-364-10 Altitude Immersion No evidence of moisture on connector interface or contacts. Connector shall meet dielectric withstanding voltage. EIA-364-03 Wired connectors with supplemental potting. Contact Retention Contact Min. Size Pounds 23 6 20 15 16 25 12 25 Min. Newtons 27 67 111 111 EIA-364-29 Contact Separation Force Contact Min. Size Ounces 23 0.5 20 0.7 16 2.0 12 3.0 Min. Newtons 0.14 0.19 0.56 0.83 SAE AS39029 Mating and Unmating Force Maximum mating/unmating force: (6 pounds) + (# of size 23 contacts X .40) + (# of size 12 or #16 contacts X 1.8) EIA-364-13 Magnetic Permeability EIA-364-54 2 μ maximum. Dimensions in Inches (millimeters) are subject to change without notice. © 2011 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: [email protected] C-8