Medallion 7100 Series CATV Fiber Amplifier Erbium Doped Fiber Amplifier (EDFA) DATASHEET | MARCH 2014 FIBER OPTICS The Medallion 7100 series product line is a family of state-of-the-art high performance CATV Erbium Doped Fiber Amplifiers (EDFA). Packaged in convenient 1 RU housing, this line of fiber amplifiers has been design optimized for superior output power stability and the exceptionally low noise figures demanded by CATV applications. Applications CATV Supertrunking High Power Distribution Networks Redundant Ring Architectures FTTx Networks Features High Saturation Output Power up to 27 dBm (Pre-Splitter) Dual Power Supplies, Redundant & Hot Swappable – AC or DC Front Panel Optical Input & Output Monitor Ports SNMPv2 Control Interface The Medallion 7100 provides very stable optical outputs over a wide operating temperature range. Internally it is supported with input and output isolators for enhanced system stability and performance. Optical power is continuously monitored at the input and output for automatic power control during operation over a wide operating temperature range. The Medallion 7100 offers a full range of flexible configurations and a rich set of features. These include remote management capability through SNMPv2, Telnet and a resident Web Server. The Medallion 7100 also supports MIBs specified by SCTE (Society of Cable Television Engineers) for this product class. For local management, an RS-232 port is standard, along with a convenient front panel control menu provided on a Vacuum Fluorescent Display (VFD). High Level Features Automatic Power Control and/or Automatic Gain Control Modes Port Count, Optical Power, and Connector Style Options Web Server Gain Flattened Options for WDM Applications IPv4 10/100bT Low Noise Figure for CATV Monitors & Alarms Wide Input Dynamic Range Very Stable Output Power Over a Wide Operating Temperature Range Optional Automatic Gain Control or Constant Output Power Operation Optional Gain Flatness Specifications Loss of Input Signal Loss of Output Power Pump Laser Diode Bias Current Pump LD Temperature Case Temperature Redundant Power Supplies Redundant Fans | REV 2014.03 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. Medallion 7100 Series CATV Fiber Amplifier ` Erbium Doped Fiber Amplifier (EDFA) FIBER OPTICS DATASHEET | MARCH 2014 Electrical Characteristics Property Symbol Min AC Power Supply Voltage VAC 85 DC Power Supply Voltage VDC -36 Power Consumption Note 1 Typ Max Unit 265 VAC -72 VDC 10 W -48 PTOT Note 1: 10 W valid at 0 dBm input and 14 dBm output power within specified operating temperature range. Optical Characteristics Property Symbol Min Typ Max Unit VAC 1528 1550 1562 nm 0 Wavelength Range Input Power Total Ouput Power Options Note 1 Output Power Delta to Nominal Output Port Count Options (SC) Noise Figure Notes 1,2 Note 3 PIN -10 12 dBm POUT 14 27 dBm POUTΔ -0.5 0.5 dB - 1 10 NF 5.0 dB dBm Optical Isolation ISO 30 Input Power Alarm LOS -12 -11 -10 dB Input Monitor Loss IMON 22 23 24 dB Output Monitor Loss OMON 22 23 34 dB Note 1: Pre-splitter total output power. Number of Ports vary by model type. Note 2: Model Types are specified by output power per port. Output power per port is limited to 21 dBm Note 3: Test condition with input power = 0 dBm (@ 1550 nm) Note 4: Specifications valid within operating temperature range. Absolute Maximum Ratings Property Symbol Min Typ Max Unit Operating Temperature Range TO 0 50 o Storage temperature Range TS -40 85 o Relative Humidity H 0 95 % C C | REV 2014.03 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. Medallion 7100 Series CATV Fiber Amplifier ` Erbium Doped Fiber Amplifier (EDFA) DATASHEET | MARCH 2014 FIBER OPTICS Outline Drawing | REV 2014.03 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. Medallion 7100 CATV Fiber Amplifier ` Erbium Doped Fiber Amplifier (EDFA) FIBER OPTICS DATASHEET | MARCH 2014 European Union “RoHS Directive” Compliance Except for the exemption claimed herein for lead used in solder for network infrastructure equipment, all homogenous materials contained in the product contain less than the maximum concentration levels for lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls and polybrominated biphenyl ethers permitted under the European Union Directive 2002/95/EC (the "RoHS Directive"). Model Number Information □□-□□□□-□□□□□ 7100Logo & Customer Specific Gain Flattened 0= EMCORE Logo 0 = Gain Flattened 1=No Logo 1 = Not Gain Flattened Output Power per Port XX = xxdBm/port (Maximum: xx=21dBm) Number of Ports Optics Optical Input Optical Output Optical Monitor Power Supply 01 = 1 port 1 = SC/APC 1 = Front 1= Front 1= Input Front, Output Front 1= AC primary, no secondary 02 = 2 ports 2 = FC/APC 2 = Rear 2= Rear 2= Input Rear, Output Rear 2=DC primary, no secondary 04 = 4 ports 3 = E2000 3 = None 3=AC primary, AC secondary 08 = 8 ports 4 = SC/APC Angled 4=AC primary, DC secondary 10 = 10 ports 5= FC/APC Angled 5=DC primary, DC secondary 6= E2000 Angled Note 1: Not all configurations are available; please contact your EMCORE Sales Representative. e.g. 7100-1401-11135 (14 dBm per port, 1 port, SC/APC, Front Fiber, Dual DC) e.g. 7100-1708-11133 (17 dBm per port, 8 ports, SC/APC, Front Fiber, Dual AC) | REV 2014.03 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. ` Medallion 7100 CATV Fiber Amplifier Erbium Doped Fiber Amplifier (EDFA) DATASHEET | MARCH 2014 FIBER OPTICS Laser Safety Information Class 1M Laser Products IEC 60825-1:2007 EN 60825-1:2007 Complies with 21 CRF 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50 dated June 24, 2007 Caution: Use of controls, adjustment and procedures other than those specified herein may result in hazardous laser radiation exposure. | REV 2014.03 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.