MAFA 2100 PA Series EDFA Micro Erbium Doped Fiber pre-Amplifier DATASHEET | DECEMBER 2013 FIBER OPTICS EMCORE’s MAFA 2100 PA Series Micro Erbium Doped Fiber pre-Amplifier is an ideal building block for OEM system integrators. The family of MAFA 2100 PA series preamps is designed to meet the most demanding noise performance requirements of any fiber link application, and perform all the functions required of an optical preamplifier for system integration. The MAFA 2100 PA series provides optical isolation on the output of the gain block for stable, low noise operation. The output optical signal power levels are detected for monitoring and control. The MAFA 2100 PA series also provides monitors and associated alarms for all vital characteristics. Optical/Electrical Characteristics1 Property Unit Limit Model - 2114 PA High-Performance Supertrunking Links Operating Input Power Pin (dBm) Max 0 High Power Distribution Networks Operating Input Power Pin (dBm) Min -45 - Redundant Ring Architectures Saturated Output Power Po(dBm) Min 14 (note 3) Nm Min/Max 1530 – 1562 Nominal Noise Figure NF (dB) Max 3.3 (note 2) Power Consumption Psys (W) Max 8 +85 C Case Applications FTTx Networks Operating Wavelength Range Features Fully Functioning EDFA Gain Block (preamp) Standard RS-232 Communication Low Electrical Power Consumption Comments - o Notes: 1. Unless stated otherwise all specifications apply over the full temperature range and humidity. ° 2. Measured @ 1550 nm, Pin -30 dBm and @ 25 C 3. Measured @ Pin = -4 dBm Output Isolation >40 dB Polarization Dependent Gain <0.1 dB Polarization Mode Dispersion <0.5 ps | REV 2013.12 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. MAFA 2100 PA Series EDFA Micro Erbium Doped Fiber pre-Amplifier FIBER OPTICS DATASHEET | DECEMBER 2013 General and Mechanical Specifications Property Operating Wavelength Requirement Comments 1530 nm ~ 1562 nm Standard Operating Case Temperature -40C to 85C Standard Storage Temperature -40C to 85C Standard 20% to 85% Non-condensing +4.5 V to +5.5 VDC Standard SC/APC; SC/UPC; FC/APC; FC/UPC; E2000/APC User Specified 4.9”W x 5.9”D x 0.8”H MAFA 2014 -PA Operating Humidity Voltage Supply Range Optical Connectors Dimensions (in) Outline Drawing | REV 2013.12 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. MAFA 2100 PA Series EDFA Micro Erbium Doped Fiber pre-Amplifier FIBER OPTICS DATASHEET | DECEMBER 2013 Electrical Connector Pinout PIN # Designation PIN # 1 DC Power Input (+5 V) 16 Designation Reserved 2 GND 17 Reserved 3 Reserved 18 RS-232 Rx* 4 Reserved 19 Reserved 5 Reserved 20 Reserved 6 RS-232 Tx 21 Reserved 7 Reserved 22 Reserved 8 Reserved 23 Reserved 9 Reserved 24 N/A 10 Reserved 25 Reserved 11 Reserved 12 Reserved 13 Reserved 14 DC Power Input (+5 V) 15 GND Compliance and Reliability Information FCC: Subpart B. Part 15 class “A”: Unintentional Radiators EN 61000-4-3: Electromagnetic Compatibility (EMC) Part 4: Testing and Measurement Techniques – Section 3: Radiated Immunity (1996) EN 55013: Sound and Television Broadcast receivers and associated equipment – Radio disturbance characteristics- limits and methods of measurements – Electric Field Radiation Emissions (2001) Fit Rate: 60% level of confidence 670 @ 25C Fit Rate: 60% of level of confidence 962 @ 40C Ordering Information MAFA2014 - - PA Connector Option SC - SC/APC FC - FC/APC EC – E2000/APC TC – SC/UPC GC – FC/UPC | REV 2013.12 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.