openGear® OPG-1L 50 MHz-2.3 GHz RF Fiber Optic Link

openGear® OPG-1L 50 MHz-2.3 GHz
RF Fiber Optic Link
DATASHEET | SEPTEMBER 2014
SATCOM
EMCORE’s openGear® OPG-1L RF Fiber Optic Links are optimized
to perform in the 50 MHz to 2.3 GHz frequency range providing
transparent signal transport for satellite antenna applications on an
open architecture platform.
The OPG-1L transmitter and receiver modules may be housed in the
same chassis as EMCORE’S openGear® HD video, audio, serial data
and USB extension / distribution cards, allowing full monitoring and control of
each module via the DashBoard Network Management System (NMS).
System Design
Features
The OPG-1L was designed to be fully compat-
„„ 50 MHz to 2.3 GHz Optimized for IF- and ible with the openGear® standard for terminal
equipment or cable headend design. This means
L-Band Video Signals
„„ Supports 30 km Links
that when you install an openGear® enclosure,
you can then purchase additional insert cards
„„ Optically-Isolated DFB Lasers Enable High- from different manufacturers to be used in the same enclosure. The standard
enclosure is a 19” rack-mount frame that can hold up to 20 insert cards. A separate
Dynamic-Range Links
„„ 25 dB Tx and Rx Adjustable Gain Range
module handles the management and control systems, and allows for local or remote interfaces. Each enclosure utilizes 2 RU of rack space, maximizing the overall
„„ Peak Optimizer for Quick and Easy Set-Up
usage of the equipment rack.
„„ SmartGain for Enhanced AGC Performance
The OPG-1L’s Rear Interface Modules may be pre-installed with its cabling, with-
„„ 50 & 75 Ohm BNC or 50 Ohm SMA
out corresponding PCBA cards. This allows the user to anticipate future expansion
needs without significantly increasing the intial investment, and without having to
„„ Blind Mate RF Coax to Support Rear Plug-in access the rear panel and cabling once installed. The user simply purchases corre-
Access
sponding PCBA cards on an as-needed basis then slides them into place from the
„„ SC/APC and LC/APC Optical Connectors
„„ Remote Monitor and Control Via Dashboard and SNMP
front of the frame, effortlessly locking them into the Rear Interface Module.
Block Diagram
„„ Push Buttons for RF Gain Adjust and LNB Transmitter
Power
Receiver
DC to LNB
„„ LED Indicators for Status and RF Levels
„„ Tx and Rx PCBA Card and Module
„„ 2 RU, 20-Slot openGear® Enclosure
© 2014 EMCORE Corporation | REV 2014.09
Sin
Push
Button
Laser
PL
PR
Photodiode
Smon
Optimizer
Smon
+1 626-293-3400
Sout
[email protected]
www.emcore.com
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
openGear® OPG-1L 50 MHz-2.3 GHz
RF Fiber Optic Link
DATASHEET | SEPTEMBER 2014
SATCOM
Performance Highlights
Frame Options
Parameter
TX
Wavelength
Value
Units
1310, 1550, CWDM
nm
5+2
dBmo
50-1000
850-2300
MHz
MHz
Optical Output Power
IF-Band Frequency
L-Band Frequency
OPG-8321
Frequency Response
Any 500 MHz
Full Band (50-2300 MHz)
Input Return Loss
dB
dB
12
dB
Tx Gain (TG) (at max gain)
25 + 2
dB
Tx Gain Adjustment Range
25
dB
Spurs Free Dynamic Range2
100
dB-Hz2/3
Noise Figure (at maximum gain, 1 GHz)
20
dB
1
Input IP3 (at maximum gain, 1 GHz)
RX
+ 0.75
+ 1.5
-4
dBm
RF Input: Within SGC Mode
0 to -35 dBm
dBm
Outside SGC Mode
5 to -50 dBm
Output Return Loss
10
dB
Rx Gain (RG) (at max gain)
20 (dual output)
25 (single output)
dB
Rx Gain Adjustment Range
25
dB
20 (dual output)
25 (single output)
dBm
1
Output IP3 (at maximum gain, 1 GHz)
OG3-FR
OPG-1L
PCBA Cards with Rear Interface Modules
1. Link RF Gain dB = TG + RG - 2*Fiber Loss dBo
2. SFDR = 2/3*(IIP3 + 174 - NF).
Mechanical Characteristics
Parameter
PCBA Card Dimension
Rear Interface Module Dimension
Value1
Units
12.8 L x 3.0 H x 0.681 W
32.5 L x 7.62 H x 0.173W
in
cm
1.362 L x 3.365 H x 1.31 W
3.46 L x 8.55 H x 3.33 W
in
cm
PCBA Cards
1. Defined per openGear Development Guide by Ross: 8200DR-001-02, 8200DR-001-03
Electrical Characteristics
Parameter
TX
Value
Power Requirement
W
12 +/- 0.5
VDC
LNB Voltage (at RF input port, 350 mA max)
17 +/- 1.0
VDC
DC Current (@ +12 V with LNB Off)
350 +/- 50
mA
Input Voltage (@ 1 A Max)
12 +/- 0.5
VDC
DC Current (@ +12 V)
250 +/- 50
mA
Input Voltage (@ 1 A Max)
RX
Units
12
© 2014 EMCORE Corporation | REV 2014.09
+1 626-293-3400
Rear Interface Modules
[email protected]
www.emcore.com
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
openGear® OPG-1L 50 MHz-2.3 GHz
RF Fiber Optic Link
DATASHEET | SEPTEMBER 2014
SATCOM
Card Compatibility to openGear® Frames
Rear Interface Module Compatibility Matrix
Card Configuration
Per Rear Interface
Module
OG3-FR
Optical Connector
LC/APC
SC/APC
DFR-8321
RF Connector
SMA
BNC
Optical Connector
LC/APC
SC/APC
RF Connector
SMA
BNC
Tx
x
x
x
x
x
x
x
x
Rx
x
x
x
x
x
x
x
x
Tx, Rx
X
X
X
X
Rx, Tx
x
x
x
x
Tx, Tx
x
x
x
x
Rx, Rx
x
x
x
x
x
x
© 2014 EMCORE Corporation | REV 2014.09
x
+1 626-293-3400
[email protected]
www.emcore.com
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
openGear® OPG-1L 50 MHz-2.3 GHz
RF Fiber Optic Link
DATASHEET | SEPTEMBER 2014
SATCOM
Ordering Information PCBA Card
Receiver
Transmitter1
OPG-UT-YY05-ZZ
OPG-UR-V-ZZ
Note 1. When installing transmitter cards in the OG3-FR frame, remove the pre-installed
LNB blocker plug from the PCBA card but leave as-is for the OPG-8321 frame to
prevent the frame’s DC-power alarm from activating.
When ordering replace “U” with one of the Frequency Band Options
When ordering replace “V” with one of the RX Only: RF Interface Options
When ordering replace “YY” with one of the Wavelength Options**
When ordering replace “ZZ” with one of the Optical Connector Options
Frequency
Band Options
“U”
I = IF-Band
Frequency
Band
(MHz)
50-1000
RX Only:
RF Interface Options
“V”
1 = Output+Monitor
2 = Dual Outputs
Wavelength
Options (nm)
“YY”
13 = 1310,
55 = 1550
Output Power
(dBmo)
Optical Connector Options
“ZZ”
05 = +5
LA = LC-APC,
SA = SC-APC (OG3-FR only)
05 = +5
LA = LC-APC,
SA = SC-APC (OG3-FR only)
27 = 1270
29 = 1290
33 = 1330
35 = 1350
37 = 1370
39 = 1390
41 = 1410
43 = 1430
45 = 1450
47 = 1470
49 = 1490
51 = 1510
53 = 1530
57 = 1570
59 = 1590
61 = 1610
L = L-Band
850-2300
1 = Output+Monitor
2 = Dual Outputs
13 = 1310,
55 = 1550
27 = 1270
29 = 1290
33 = 1330
35 = 1350
37 = 1370
39 = 1390
41 = 1410
43 = 1430
45 = 1450
47 = 1470
49 = 1490
51 = 1510
53 = 1530
57 = 1570
59 = 1590
61 = 1610
Ordering Information for Rear Interface Module (RIM)
Transmitter/Receiver
OPG-WX
RF Connector
Options
“W”
B = BNC,
S = SMA
RF Connector
Impedance
Options (ohm)
“X”
5 = 50,
7 = 75 (BNC only)
When ordering replace “W” with one of the RF Connector Options
When ordering replace “X” with one of the RF Connector Impedance Options
© 2014 EMCORE Corporation | REV 2014.09
+1 626-293-3400
[email protected]
www.emcore.com
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
openGear® OPG-1L 50 MHz-2.3 GHz
RF Fiber Optic Link
DATASHEET | SEPTEMBER 2014
SATCOM
Laser Safety
This product meets the appropriate standard in Title 21 of the Code of Federal Regulations (CFR). FDA/CDRH Class 1M laser
product. This device has been classified with the FDA/CDRH under accession number 0220191. All versions of this laser are Class
1M laser product, tested according to IEC 60825-1:2007 / EN 60825-1:2007. An additional warning for Class 1M laser products.
For diverging beams, this warning shall state that viewing the laser output with certain optical instruments (for example: eye
loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. For collimated beams, this warning
shall state that viewing the laser output with certain instruments designed for use at a distance (for example: telescopes and
binoculars) may pose an eye hazard.
Wavelength = 1.3/1.5 μm.
Maximum power = 30 mW.
INVISIBLE LASER RADIATION
AVOID DIRECT EXPOSURE
TO BEAM
Wavelength: 1.5 µm
Max. Output: 50 mW
Class 1M Laser Product
INVISIBLE LASER RADIATION IS
EMITTED FROM THE END OF
FIBER OR CONNECTOR
Avoid direct exposure to beam
Do not view beam directly with
optical instruments
INVISIBLE LASER RADIATION EMITTED FROM END OF FIBER OR CONNECTOR
CLASS 1M LASER PRODUCT IEC 60825-1:2007 EN 60825-1:2007
MAX OUTPUT: 50 mW WAVELENGTH: 1.5 µm (+ 1460 to 1620 nm)
Complies with 21 CRF 1040.10 and 1040.11 except for deviations pursuant
to Laser Notice No. 50, dated June 24, 2007
G8760-073-001 REV.3
*Caution - Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
*IEC is a registered trademark of the International Electrotechnical Commision.
© 2014 EMCORE Corporation | REV 2014.09
+1 626-293-3400
[email protected]
www.emcore.com
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.