359C - EMCORE Corporation

359C Series 1550 nm
Dispersion Compensation Module
DATASHEET | NOVEMBER 2014
MICROWAVE
The 359C Series Dispersion Compensation Module provides a solution for dealing with existing high dispersion legacy installations. By providing a negative
dispersion, fiber with high positive dispersion can be fully compensated. Typical
dispersion compensation modules can increase the total fiber length by as much
as 65%, while these highly efficient high dispersion fibers only increase the total
fiber length of the system by approximately 13%. Thus lessening the requirement
on the EDFA modules required to compensate for the total fiber loss.
The 359X platform works with a wide range of fiber optic transport products for
satellite and microwave communications from 1 MHz to 40 GHz. These units can
be used to construct transparent inter- and intra-facility links from 1 meter to
Applications
„„ Radar Testing/Calibration
„„ Signal Processing
„„ Phased Array Antennas
„„ Phase Noise Processing
„„ Antenna Site Diversity
>100 km for RF and microwave signal transport, antenna remoting, video transport, electronic warfare systems and other high-dynamic-range applications.
Delay Length & Dispersion Specifications
Product
Size
Max Delay
Max. Length
Total Dispersion
359C
1 RU
110 µs
24 km
-1.6*105 ps/nm
Note: Max length of SMF-28 brought to 0 dispersion is 183.4 km.
Features
„„ Delays Up to 110 microseconds
„„ 24 KM
„„ Small Size
„„ Flat RF Amplitude Response and Phase
© 2014 EMCORE Corporation | REV 2014.11
Optical Specifications
Parameter
Typical
Units
Attenuation @ 1550 nm
< 0.25
dB/km
IOR @ 1550 nm
1.469
Typical Total Dispersion @ 1550 nm
-130
+1 626-293-3400
ps/nm-km
[email protected]
www.emcore.com
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
359C Series 1550 nm
Dispersion Compensation Module
DATASHEET | NOVEMBER 2014
MICROWAVE
Mechanical Specifications
Description
Value
Units
16.75 (425.4) x 1.72 (43.7) x 12 (304.8)
16.75 (425.4) x 5.22 (132.6) x 18 (458)
16.75 (425.4) x 8.72 (221.5) x 18 (458)
in (mm)
Faceplate Dimensions
1 RU
3 RU
5 RU
19 (482.6) x 1.75 (44.5)
19 (482.6) x 5.25 (133.4)
19 (482.6) x 8.75 (222.3)
in (mm)
Storage Temperature
-60 to +85
°C
Operating Temperature
-40 to +85
°C
Body Dimensions
1 RU
3 RU
5 RU
Ordering Information
Product Number
359C-WW-XXXXXX-YY-ZZ
„„ When ordering replace “WW” with one of the Rack Unit Size Options
„„ When ordering replace “XXXXXX” with one of the Delay Options
„„ When ordering replace “YY” with one of the Connector Type Options
„„ When ordering replace “Z”Z with one of the Optional Features
Coil Type
“C
Rack Unit Size
“WW”
C = Zero Compensation
Dispersion
1U = 19” x 1.75” (1 RU)
Delay in µS
“XXXXXX”
001000 = 10 µs Delay
010000 = 100 µs Delay
Connector Type
“YY”
SA = SC/APC
FA = FC/APC
LA = LC/APC
EA = E2000/APC
Optional Features*
“ZZ”
P = Pigtail Leads
B = Bulkhead
Pigtail Leads - If preferred, the standard bulkhead connector input and output of the 359C Series Delay and Dispersion Compensation Modules
can be replaced with a one meter long pigtail with a male connector on the end.
© 2014 EMCORE Corporation | REV 2014.11
+1 626-293-3400
[email protected]
www.emcore.com
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.