PONA 2114 PA Series EDFA Erbium Doped Fiber pre-Amplifier DATASHEET | DECEMBER 2013 Applications High-Performance Supertrunking Links Optical Distribution Networks Redundant Ring Architectures FTTx Networks. FIBER OPTICS The EMCORE PONA 2114 PA Series Erbium Doped Fiber pre-Amplifier (EDFA) is an ideal building block for OEM system integrators. The family of PONA 2114 PA series preamps is designed to meet the most demanding noise performance requirements of any fiber link application, and perform all the functions required of an optical pre-Amplifier for system integration. The PONA 2114 PA series provides optical isolation on the output of the gain block for stable, low noise operation. The output optical signal power levels are detected for monitoring and control. The PONA 2114 PA series also provides monitors and associated alarms for all vital characteristics. The relay outputs of the PONA 2114 PA series provide electrical monitoring of alarm conditioning of the unit. General and Mechanical Specifications Features Full Functionality 1 RU EDFA (pre-Amp) Low Noise Figure (Typ < 3.3 dB) Total Input Power Range: -45 dBm to 0 dBm Property Operating Wavelength Operating Case Temperature Storage Temperature +14 dBm Saturated Output Power (min) Operating Humidity Small Signal Gain 37 dB (min) Voltage Supply Range Standard RS-232 Communications (RS-485 or I2C is Optional) Optical Connectors Dimensions in Inches Key Lock Switch Requirement Comments 1530 – 1562 nm Standard 0C to 50C -40C to 85C Standard 20% to 85% Non-condensing 85 VAC to 265 VAC 50/60 Hz -36 to -60 V DC Standard Optional SC/APC; SC/UPC; FC/APC; FC/UPC; E2000/APC User Specified 19.0”W x 14.76”D x 1.72”H 19” Rack-Mounted, 1U VFD Panel Status Indicator Low Electrical Power Consumption Output Isolation >40 dB Polarization Dependant Gain < 0.1 dB Polarization Mode Dispersion < 0.5 ps | REV 2013.12 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. PONA 2114 PA Series EDFA Erbium Doped Fiber pre-Amplifier FIBER OPTICS DATASHEET | DECEMBER 2013 Optical/Electrical Characteristics1 Property Symbol (Units) Limit Operating Input Power Pin (dBm) Max 0 Operating Input Power Pin (dBm) Min -45 Saturated Output Power Po (dBm) Operating Wavelength Range Specifications Comments 14 Minimum (Note 2) nm Min/Max 1530 – 1562 Nominal Noise Figure NF (dB) Max 3.3 (note 3) Power Consumption Psys (W) Max 6 +50°C case Notes: 1. Unless stated otherwise, all specifications apply over the full operating temperature and humidity ranges. 2. Measured @ 1550 nm, Pin -4 dBm and @ 25°C. 3. Measured @ 1550 nm, Pin -30 dBm and @ 25°C. Outline Drawing AC versions shown below with 8-port option DC versions shown below with 8-port option | REV 2013.12 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. PONA 2114 PA Series EDFA Erbium Doped Fiber pre-Amplifier FIBER OPTICS DATASHEET | DECEMBER 2013 Compliance Information 89/336/EEC 73/23/EEC EN 50083-2, (2001) Electromagnetic Compatibility Directive, amended by 92/31/EEC & 93/68/EEC Low Voltage Directive, amended by 93/68/EEC Cable networks for TV signals, sounds and interactive services, Part 2 Electromagnetic Compatibility for equipment. Mains Conducted Emissions Mains Frequency and its Harmonics, Conducted Emissions Radiation from Active Equipment, Radiated Immunity Immunity of Active Equipment, Radiated Immunity Immunity of Active Equipment, Radiated Immunity Electrostatic Discharge Immunity Electrical Fast Transient / Burst Immunity Low Voltage Directives Laser Safety Requirement Laser Safety Requirement Laser Safety Requirement 90% level of confidence < 1700 @ 30C (PONA 2130) EN 55013 EN 61000-3-2 EN 55020 EN 61000-4-6 EN 61000-4-3 EN 61000-4-2 EN 61000-4-4 EN 60950 EN 60825-1 EN 60825-2 CDRH Fit Rate: Ordering Information PONA 2114 - 1 - - Input Voltage - PA Connector Type AC – 90-260V 50/60 Hz SC – SC/APC DC – 48 V FC - FC/APC EC – E2000/APC TC – SC/UPC GC – FC/UPC Laser Safety Information This product meets the applicable requirements of 21 CFR 1010 & 1040 and is classified as a Class IV laser product based on the maximum optical output power shown below. During use as intended, the laser energy is fully contained within the fiber network such that there is no accessible laser radiation and would meet the requirements for a Class I laser product. The laser product report has been submitted to the CDRH and the accession number is expected by October 2006. Wavelength = 1530 ~ 1562 nm (dependant on input source) Maximum Output Power = 30 mW (single output) | REV 2013.12 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.