Velociti Series ABD-2F and ABD-RT2F

Velociti® Series
ABD-2F and ABD-RT2F
Single-Ended Reflected Type
Beam Smoke Sensor
Description
The Gamewell-FCI Velociti® Series, ABD-2F and addressable projected beam smoke sensor is uniquely suited to
sense smoke in hostile environments or open areas with
high ceilings where spot-type sensors are unsuitable or
difficult to install and maintain. It is intended for use in the
signaling line circuits with the following sub-assemblies.
• E3 Series®, ILI-MB-E3 and ILI-S-E3 (Velociti mode only)
• S3 Series, SLC-PM (Signaling Line Circuit-Personality
Module)
The ABD-2F consists of a combination transmitter/
receiver unit and a reflector. When smoke enters the path
between the unit and the reflector, it causes a reduction in
the signal, and when the smoke level reaches the predetermined threshold, an alarm results.
A unique single-ended reflective design offers simpler
installation than the traditional transmitter and receiver
types of beam sensors. Alignment is swiftly accomplished
via an optical sight and a 2-digit signal strength meter integral with the product. Listed for operation from –22° F to
131° F, the ABD-2F can be installed in garages, warehouses and other hostile environments where temperature
extremes exceed the capability of spot-type sensors.
®
The Velociti Series uses a communication protocol that
substantially increases the speed of communication
between the sensors and Gamewell-FCI analog addressable fire alarm controls. These devices operate in a
grouped fashion. If one of the devices in the group
changes status, the panel’s microprocessor stops the
group poll and concentrates on the single device. The net
effect is response speed up to five times greater than earlier designs.
The unit has four standard sensitivity selections along with
two Acclimate settings. When either of the two Acclimate
settings are selected, the sensor will automatically adjust
its sensitivity using the advanced software algorithms to
select the optimum sensitivity for the specific environment.
ABD-2F/RT2F
Features
• Includes a single-ended, reflective design.
• Has six user-selectable sensitivity levels.
• Spans a 16 to 328 foot (4.9 to 99.9 m) detection range.
• Compatible with the E3 Series® ILI-MB-E3 and ILI-S-E3
or the S3 Series, SLC-PM.
• Contains an integral sensitivity test feature (ABD-2SF).
• Designed with a digital display - no special tools
required.
• Provides a user-friendly alignment procedure.
• Offers an integral automatic gain control that compensates for signal deterioration from dust build-up.
• Available with an optional Remote test station.
SIGNALING
FM
MEA
Approved
FDNY
S1913 3023594 COA #:219-02-E 7260-1703:0120
Vol. VI
APPROVED
®
®
Velociti and E3 Series are registered trademarks of Honeywell International Inc.
GAMEWELL-FCI
12 Clintonville Road, Northford, CT 06472-1610 USA • Tel: (203) 484-7161 • Fax: (203) 484-7118
Specifications are for information only, are not intended for installation purposes, and are subject to change without notice. No responsibility is assumed by Gamewell-FCI for their use.
www.gamewell-fci.com
9020-0623 Rev. F page 1 of 2
©2013 by Honeywell International Inc. All rights reserved.
Description (continued)
Ordering Information
The ABD-RT2F is equipped with an integral sensitivity test
feature consisting of a test filter attached to a servo motor
inside the sensor optics. The ABD-RT2F requires an additional, external power supply. Using the remote test station
Model RTS151, the motor moves the filter in the path of
the light beam, thereby serving as an accurate test of the
receiver sensitivity. This test feature allows the user to
quickly and easily meet the annual maintenance and test
requirements of NFPA 72.
Part Number Description
Specifications
Operating Temperature
Range:
Operating Humidity
Range:
Dimensions:
Detector:
Reflector:
Voltage Range:
Alarm Current:
Standby Current:
-22° F to 131° F
(-30° C to 55° C)
B210LP
Flanged mounting base.
Dimensions: 6.1” (15.5 cm) diameter.
B210LPBP Flanged mounting base bulk pack.
Dimensions: 6.1 (15.5 cm) diameter.
ABD-RT2F Single-ended smoke sensor with integral
sensitivity test.
BEAMLRK Long range accessory kit (required for
applications with a range over 230 ft. (70m).
BEAMMMK Multi-mount kit (provides ceiling or wall
mount capability with increased angular
adjustment).
BEAMSMK Surface mount kit.
RTS151
Remote test station.
RTS151KEY Remote test station with key lock.
10% to 93 RH
non-condensing
10” H x 7.5” W x 3.3” D
(25.4 H x 19 W x 8.4 D cm)
16-230 ft. (4.9 x 70.1 m)
7.9” H x 9.1” W
(20 H x 23 W cm)
15 to 32 VDC
8.5 mA max.
2 mA max. avg. @ 24 VDC
GAMEWELL-FCI
12 Clintonville Road, Northford, CT 06472-1610 USA • Tel: (203) 484-7161 • Fax: (203) 484-7118
9020-0623 Rev. F page 2 of 2
www.gamewell-fci.com