9020-0617 - Gamewell

Velociti® Series
ASD-PL2F, ASD-PTL2F
and ASD-PL2FR
Description
Analog, Addressable Photoelectronic
Smoke Sensor
The Gamewell-FCI Velociti® Series, analog addressable plug-in smoke sensors with integral communication provide features that surpass conventional
sensors. Sensitivity can be programmed in the control panel software, and is continuously monitored
and reported to the panel. Point ID capability allows
each sensor’s address to be set, providing exact
locations for selective maintenance when the chamber contamination reaches an unacceptable level.
The ASD-PL2F photoelectric sensor’s unique optical
sensing chamber is engineered to sense smoke produced by a wide range of combustion sources. Dual
electronic thermistors add 135°F (57°C) fixed-temperature thermal sensing on the ASD-PTL2F model.
ASD-PL2FR
ASD-PL2F/ASD-PTL2F
Features
• Sleek, low-profile design.
• Visual rotary, decimal switch addressing (01-159).
• Built-in functional test switch activated by an external
The Velociti® Series use a communication protocol
that substantially increases the speed of communication between the sensors and certain Gamewell-FCI
analog addressable fire alarm controls. These
devices operate in a grouped fashion. If one of the
devices in the group has a status change, the panel’s
microprocessor stops the group poll and concentrates on the single device. The net effect is a
response speed up to five times greater than earlier
designs.
magnet.
• Bicolor LEDs flash green whenever the sensor is
addressed, and light steady red on alarm.*
• Optional relay, isolator, or sounder bases.
• Low standby current.
• Analog addressable communication.
• Stable communication technique with noise immunity.
• Optional remote, single-gang LED Indicator (RA100Z).
• Compatible with Gamewell-FCI analog addressable
panels.
Ordering Information
Part Number Description
ASD-PL2F Analog, addressable photoelectronic
smoke sensor
ASD-PTL2F Analog, addressable photoelectronic smoke
sensor with thermal sensing
ASD-PL2FR Analog, addressable photoelectronic smoke
sensor used with the DNR duct base when
the remote test is required.
Note: *Only the red LED is operative in panels that do not operate
in Velociti® mode.
SIGNALING
FM
Velociti® is a registered trademark of Honeywell International Inc.
APPROVED
S1913
UL® is a registered trademark of Underwriters Laboratories Inc.
MEA
Approved
FDNY
3023594 COA #:219-02-E 7272-1703:0121
Vol.VI
GAMEWELL-FCI
12 Clintonville Road, Northford, CT 06472-1653 USA • Tel: (203) 484-7161 • Fax: (203) 484-7118
Specifications are for information only, are not intended for installation purposes, and are subject to change without notice. No responsibility is assumed by Gamewell-FCI for their use.
www.gamewell-fci.com
9020-0617 Rev. J page 1 of 2
©2013 by Honeywell International Inc. All rights reserved.
Installation
Specifications
ASD-PL2F plug-in sensors use a separate base to
simplify installation, service, and maintenance. A
special tool allows maintenance personnel to plug-in
and remove sensors without using a ladder.
Mount the base on a box which is at least 1.5" (3.8 cm)
deep. Suitable mounting base boxes include:
• 4.0" (10.2 cm) square box.
• 3.5" (8.9 cm) or 4.0" (10.2 cm) octagonal box.
• Single-gang box (except relay or isolator bases).
• With B200S or B200SR base, mounted on a 4.0"
(10.2 cm) octagonal or square box.
• With B224RB or B224BI base, mounted on a 3.5"
ASD-PL2F, ASD-PTL2F, ASD-PL2FR:
2.1” (5.1 cm) height
4.1” (10.4 cm) installed in the B501 base
6.1” (15.5 cm) installed in the B210LP base
Shipping Weight: 5.2 oz. (147 g)
Operating
ASD-PL2F:
32° F to 120° F (0° C to 49° C)
Temperature:
ASD-PTL2F:
32° F to 100° F (0° C to 38° C)
0-4000 ft./min. (1,219.2 m/min.),
UL®-Listed
Velocity Range: suitable for installation in ducts.
Relative
10-93% (non-condensing)
Humidity:
Thermal Ratings: Fixed-temperature setpoint
135° F (57° C)
Dimensions:
Diameter:
(8.9 cm) octagonal box, or a 4.0" (10.2 cm) octagonal or
Electrical Specifications
square box.
NOTE: Because of the inherent supervision provided
by the SLC, end-of-line resistors are not required.
Wiring “T-taps” or branches are permitted for Style 4
(Class “B”) wiring.
Sensor Spacing
Gamewell-FCI recommends that the spacing sensors
be used in compliance with NFPA 72.
Voltage Range: 15 – 32 volts DC peak
Standby Current: (max. avg.): .0003 A @ 24 VDC
(One communication every 5
seconds with LED blink enabled).
Maximum Alarm.0065 A @ 24 VDC (LED) lit).
Current:
Bases and Options
B501
Dimensions:
B210LP
Dimensions:
B210LPBP
Dimensions:
B224RB
Relay Base
Dimensions:
B200S
Dimensions:
B200SR
Dimensions:
RA100Z
BCK-200
DNR
Plug-in sensor base without flange
4.1” (10.4 cm) diameter
Flanged mounting base
6.1” (15.5 cm) diameter
Flanged mounting base bulk pack
6.1” (15.5 cm) diameter
Plug-in sensor base with auxiliary
relay, SPDT, rated 2 amps @ 30 VDC
(resistive).
Screw terminals:
Up to 14 AWG (2.0 mm2)
2 coil latching relay 1 Form C contact
UL/CSA Rating:
0.9 A @ 125 VAC, inductive
0.9 A @ 110 VDC, inductive
3 A @ 30 VDC, resistive
6.1” (15.5 cm) diameter
Maximum: 25 devices between
isolator bases.
Intelligent sensor sounder base
6.875” (17.5 cm) diameter
Standard sounder base, UL 8649th
Edition compliant, ULC Listed
6.875” (17.5 cm) diameter
Remote LED Annunciator
Black detector covers (box of 10)
Duct smoke housing
GAMEWELL-FCI
12 Clintonville Road, Northford, CT 06472-1653 USA • Tel: (203) 484-7161 • Fax: (203) 484-7118
9020-0617 Rev. J page 2 of 2
www.gamewell-fci.com