TSOP753.., TSOP755.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES • Very low supply current • Photo detector and preamplifier in one package • Compatible also with short burst dataformats • Supply voltage: 2.5 V to 5.5 V • Improved immunity against ambient light 4 3 • Capable of side or top view 2 • Two lenses for high sensitivity and wide receiving angle 1 • Insensitive to supply voltage ripple and noise 20953 • Narrow optical filter to reduce interference from plasma TV emissions • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 MECHANICAL DATA Pinning: DESCRIPTION 1, 4 = GND, 2 = VS, 3 = OUT The TSOP753.., TSOP755.. series are a two lens miniaturized receiver module for infrared remote control systems. One PIN diode per lens and a preamplifier are assembled on a leadframe, the epoxy lens cap is designed as an IR filter. ORDERING CODE Taping: TSOP75...TT - top view taped TSOP75...TR - side view taped The demodulated output signal can be directly connected to a microprocessor for decoding. The TSOP753.. is optimized to better suppress spurious pulses from energy saving lamps. The TSOP755.. has an excellent noise suppression. It is immune to dimmed LCD backlighting and any fluorescent lamps. AGC3 and AGC5 may also suppress some data signals in case of continuous transmission. This component has not been qualified according to automotive specifications. PARTS TABLE NOISY ENVIRONMENTS AND SHORT BURSTS (AGC3) VERY NOISY ENVIRONMENTS AND SHORT BURSTS (AGC5) 30 kHz TSOP75330 TSOP75530 33 kHz TSOP75333 TSOP75533 36 kHz TSOP75336 (1) TSOP75536 38 kHz TSOP75338 (2)(3)(4)(5) TSOP75538 40 kHz TSOP75340 TSOP75540 56 kHz TSOP75356 AGC Carrier frequency TSOP75556 Package Heimdall Pinning 1, 4 = GND, 2 = VS, 3 = OUT Dimensions (mm) 6.8 W x 3.0 H x 3.2 D Mounting SMD Application Best remote control code Rev. 1.2, 17-Apr-15 Remote control (1) MCIR (2) Mitsubishi 1 (3) RECS-80 Code (4) r-map (5) XMP-1, XMP-2 Document Number: 82495 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP753.., TSOP755.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 17170_5 2 IR receiver VS 3 Input Band pass AGC OUT Demodulator VO GND GND Control circuit µC OUT 1, 4 PIN + VS C1 Circuit VS 30 k Ω R1 Transmitter with TSALxxxx GND R1 and C1 are recommended for protection against EOS. Components should be in the range of 33 Ω < R1 < 1 kΩ, C1 > 0.1 µF. 20445-1 ABSOLUTE MAXIMUM RATINGS PARAMETER Supply voltage Supply current Output voltage Output current Junction temperature Storage temperature range Operating temperature range Power consumption TEST CONDITION SYMBOL VS IS VO IO Tj Tstg Tamb Ptot Tamb ≤ 85 °C VALUE -0.3 to +6 3 -0.3 to (VS + 0.3) 5 100 -25 to +85 -25 to +85 10 UNIT V mA V mA °C °C °C mW Note • Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability. ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER Supply voltage TEST CONDITION Ev = 0, VS = 3.3 V Ev = 40 klx, sunlight Ev = 0, test signal see fig. 1, IR diode TSAL6200, IF = 200 mA IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see fig. 1 Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Angle of half transmission distance Supply current Transmission distance Output voltage low Minimum irradiance Maximum irradiance Directivity SYMBOL VS ISD ISH MIN. 2.5 0.27 TYP. MAX. 5.5 0.45 0.35 0.45 d UNIT V mA mA 45 m VOSL 0.12 Ee min. Ee max. ϕ1/2 100 mV 0.25 mW/m2 W/m2 deg 30 ± 50 TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) 0.4 Optical Test Signal (IR diode TSAL6200, IF = 0.4 A, N = 6 pulses, f = f0, t = 10 ms) tpo - Output Pulse Width (ms) Ee t tpi *) T *) tpi ≥ 6/f0 is recommended for optimal function Output Signal VO 1) 2) VOH VOL 14337 3/f0 < td < 9/f0 tpi - 4/f0 < tpo < tpi + 6/f0 td 1) tpo 2) 0.3 0.25 Output Pulse Width 0.2 0.15 Input Burst Length 0.1 0.05 0 0.1 t 20760 Fig. 1 - Output Active Low Rev. 1.2, 17-Apr-15 0.35 λ = 950 nm, optical test signal, fig. 1 1 10 100 1000 10 000 Ee - Irradiance (mW/m²) Fig. 2 - Pulse Length and Sensitivity in Dark Ambient 2 Document Number: 82495 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP753.., TSOP755.. www.vishay.com Optical Test Signal 600 µs Ee min. - Threshold Irradiance (mW/m²) Ee Vishay Semiconductors t 600 µs t = 60 ms 94 8134 Output Signal, (see fig. 4) VO VOH VOL t off t on 4 Correlation with Ambient Light Sources: 3.5 10 W/m² = 1.4 klx (Std. illum. A, T = 2855 K) 10 W/m² = 8.2 klx (Daylight, T = 5900 K) 3 Wavelength of Ambient Illumination: λ = 950 nm 2.5 2 1.5 1 0.5 0 0.01 t 20745 Ton, Toff - Output Pulse Width (ms) 0.8 Ton 0.7 0.6 0.5 Toff 0.4 0.3 0.2 λ = 950 nm, Optical Test Signal, Fig. 3 0.1 0 0.1 20744 1 10 100 1 10 100 Fig. 6 - Sensitivity in Bright Ambient Ee min. - Threshold Irradiance (mW/m2) Fig. 3 - Output Function 0.1 Ee - Ambient DC Irradiance (W/m²) 1000 10 000 Ee - Irradiance (mW/m²) 3.0 2.5 f = f0 f = 30 kHz f = 10 kHz f = 100 Hz 2.0 1.5 1.0 0.5 0 1 10 100 1000 ΔVS RMS - AC Voltage on DC Supply Voltage (mV) Fig. 4 - Output Pulse Diagram Fig. 7 - Sensitivity vs. Supply Voltage Disturbances 1.2 1 Max. Envelope Duty Cycle E e min./Ee - Rel. Responsivity 0.9 1.0 0.8 0.6 0.4 f = f0 ± 5 % Δ f(3 dB) = f0/10 0.2 f = 38 kHz, Ee = 2 mW/m² 0.8 0.7 0.6 0.5 0.4 0.3 TSOP753.. 0.2 0.1 0.0 TSOP755.. 0 0.7 16925 0.9 1.1 0 1.3 22183 f/f0 - Relative Frequency Fig. 5 - Frequency Dependence of Responsivity Rev. 1.2, 17-Apr-15 20 40 60 80 100 120 Burst Length (number of cycles/burst) Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length 3 Document Number: 82495 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP753.., TSOP755.. Ee min. - Threshold Irradiance (mW/m2) www.vishay.com Vishay Semiconductors 0° 0.30 20° 30° 0.25 40° 0.20 1.0 0.15 0.10 0.9 50° 0.8 60° 70° 0.05 80° 0 -30 -10 10 30 50 70 0.6 90 Tamb - Ambient Temperature (°C) 0.4 0.2 0 drel - Relative Transmission Distance 21428 Fig. 9 - Sensitivity vs. Ambient Temperature Fig. 12 - Vertical Directivity 0.30 1.0 0.9 Ee min. - Sensitivity (mW/m2) S (λ) rel - Relative Spectral Sensitivity 10° 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 750 0.25 0.20 0.15 0.10 0.05 0.00 800 850 900 950 1000 1050 1100 1150 1 λ- Wavelength (nm) 21425 Fig. 10 - Relative Spectral Sensitivity vs. Wavelength 0° 10° 2 3 4 5 VS - Supply Voltage (V) 20° Fig. 13 - Sensitivity vs. Supply Voltage 30° 40° 1.0 0.9 50° 0.8 60° 70° 80° 0.6 0.4 0.2 0 drel - Relative Transmission Distance 21427 Fig. 11 - Horizontal Directivity Rev. 1.2, 17-Apr-15 4 Document Number: 82495 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP753.., TSOP755.. www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT IR Signal The TSOP753.., TSOP755.. series are designed to suppress spurious output pulses due to noise or disturbance signals. Data and disturbance signals can be distinguished by the devices according to carrier frequency, burst length and envelope duty cycle. The data signal should be close to the band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. When a data signal is applied to the TSOP753.. and TSOP755.. in the presence of a disturbance signal, the sensitivity of the receiver is reduced to insure that no spurious pulses are present at the output. Some examples of disturbance signals which are suppressed are: 0 5 • DC light (e.g. from tungsten bulb or sunlight) • Continuous signals at any frequency 10 15 20 Time (ms) 16920 Fig. 14 - IR Discturbance from Fluorescent Lamp with Low Modulation IR Signal • Strongly or weakly modulated pattern from fluorescent lamps with electronic ballasts (see fig. 14 or fig. 15) 0 16921 5 10 15 20 Time (ms) Fig. 15 - IR Discturbance from Fluorescent Lamp with High Modulation TSOP753.. TSOP755.. Minimum burst length 6 cycles/burst 6 cycles/burst After each burst of length a minimum gap time is required of 6 to 35 cycles ≥ 10 cycles 6 to 24 cycles ≥ 10 cycles 35 cycles 24 cycles > 4 x burst length > 25 ms 2000 2000 For bursts greater than a minimum gap time in the data stream is needed of Maximum number of continuous short bursts/second MCIR code preferred yes XMP-1, XMP-2 code preferred yes Most common disturbance patterns are suppressed Most common disturbance patterns are suppressed Suppression of interference from fluorescent lamps Notes • For data formats with long bursts please see the datasheet for TSOP752.., TSOP754.. • Best choice of AGC for some popular IR-codes: - TSOP75336: MCIR - TSOP75538: Mitsubishi, RECS-80 Code - TSOP75338: XMP-1, XMP-2, r-map • For SIRCS 15 and 20 bit, Sony 12 bit IR-codes, please see the datasheet for TSOP75S40F • For RCMM, TSOP75G36 provides the highest pulse accuracy with some loss of sensitivity Rev. 1.2, 17-Apr-15 5 Document Number: 82495 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP753.., TSOP755.. www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 6.8 6.6 ± 0.1 3.2 (3.4) Mold residue Mold residue 2.5 (1.8) 1.2 ± 0.2 3 0.8 2.2 (0.635) (1) 1.27 (3 x) 0.5 ± 0.1 (4 x) technical drawings according to DIN specifications 3 x 1.27 = 3.81 Marking area 2.2 Not indicated tolerances ± 0.15 (1.65) Tool separation line (2.2) Proposed pad layout from component side (for reference only) 3 x 1.27 = 3.81 1.27 Pick and place area 1.8 (R1.3) Drawing-No.: 6.550-5297.01-4 Issue: 4; 13.09.11 0.8 22608 ASSEMBLY INSTRUCTIONS Reflow Soldering Manual Soldering • Reflow soldering must be done within 72 h while stored under a max. temperature of 30 °C, 60 % RH after opening the dry pack envelope • Use a soldering iron of 25 W or less. Adjust the temperature of the soldering iron below 300 °C • Set the furnace temperatures for pre-heating and heating in accordance with the reflow temperature profile as shown in the diagram. Exercise extreme care to keep the maximum temperature below 260 °C. The temperature shown in the profile means the temperature at the device surface. Since there is a temperature difference between the component and the circuit board, it should be verified that the temperature of the device is accurately being measured • Handle products only after the temperature has cooled off • Finish soldering within 3 s • Handling after reflow should be done only after the work surface has been cooled off Rev. 1.2, 17-Apr-15 6 Document Number: 82495 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP753.., TSOP755.. www.vishay.com Vishay Semiconductors VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE 300 max. 260 °C 245 °C 255 °C 240 °C 217 °C 250 T (°C) 200 max. 20 s 150 max. 100 s max. 120 s 100 max. Ramp Up 3 °C/s max. Ramp Down 6 °C/s 50 0 0 50 100 150 t (s) 19800 200 250 300 max. 2 cycles allowed TAPING VERSION TSOP..TR DIMENSIONS in millimeters 3.3 0.3 4° 7.1 16 7.5 1.75 2.8 4° 1.34 ref. Ø 1.5 Direction of feed 8 2 Ø 1.5 min 4 technical drawings according to DIN specifications Drawing-No.: 9.700-5337.01-4 Issue: 1; 16.10.08 21577 Rev. 1.2, 17-Apr-15 7 Document Number: 82495 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP753.., TSOP755.. www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TT DIMENSIONS in millimeters 3.35 0.3 4° 7.1 16 7.5 3.3 4° 1.75 Ø 1.5 4 8 Direction of feed 2 Ø 1.5 min. technical drawings according to DIN specifications Drawing-No.: 9.700-5338.01-4 Issue: 3; 09.06.09 21578 Rev. 1.2, 17-Apr-15 8 Document Number: 82495 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP753.., TSOP755.. www.vishay.com Vishay Semiconductors REEL DIMENSIONS in millimeters 16734 LEADER AND TRAILER DIMENSIONS in millimeters Trailer no devices Leader devices no devices End Start min. 200 min. 400 96 11818 COVER TAPE PEEL STRENGTH LABEL According to DIN EN 60286-3 Standard bar code labels for finished goods 0.1 N to 1.3 N The standard bar code labels are product labels and used for identification of goods. The finished goods are packed in final packing area. The standard packing units are labeled with standard bar code labels before transported as finished goods to warehouses. The labels are on each packing unit and contain Vishay Semiconductor GmbH specific data. 300 ± 10 mm/min. 165° to 180° peel angle Rev. 1.2, 17-Apr-15 9 Document Number: 82495 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP753.., TSOP755.. www.vishay.com Vishay Semiconductors VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods) PLAIN WRITING ABBREVIATION LENGTH Item-description - 18 Item-number INO 8 Selection-code SEL 3 LOT-/serial-number BATCH 10 COD 3 (YWW) Plant-code PTC 2 Quantity QTY 8 Accepted by ACC - Packed by PCK - Data-code Mixed code indicator Origin LONG BAR CODE TOP MIXED CODE - xxxxxxx+ Company logo TYPE LENGTH Item-number N 8 Plant-code N 2 Sequence-number X 3 Quantity N 8 Total length - 21 SHORT BAR CODE BOTTOM TYPE LENGTH Selection-code X 3 Data-code N 3 Batch-number X 10 Filter - 1 Total length - 17 DRY PACKING After more than 72 h under these conditions moisture content will be too high for reflow soldering. The reel is packed in an anti-humidity bag to protect the devices from absorbing moisture during transportation and storage. In case of moisture absorption, the devices will recover to the former condition by drying under the following condition: 192 h at 40 °C + 5 °C / - 0 °C and < 5 % RH (dry air/nitrogen) or 96 h at 60 °C + 5 °C and < 5 % RH for all device containers or 24 h at 125 °C + 5 °C not suitable for reel or tubes. Aluminum bag Label An EIA JEDEC® standard J-STD-020 level 4 label is included on all dry bags. Reel LEVEL CAUTION This bag contains MOISTURE-SENSITIVE DEVICES 15973 FINAL PACKING 4 1. Shelf life in sealed bag: 12 months at < 40 °C and < 90 % relative humidity (RH) 2. After this bag is opened, devices that will be subjected to soldering reflow or equivalent processing (peak package body temp. 260 °C) must be 2a. Mounted within 72 hours at factory condition of < 30 °C/60 % RH or 2b. Stored at < 5 % RH The sealed reel is packed into a cardboard box. A secondary cardboard box is used for shipping purposes. 3. Devices require baking befor mounting if: Humidity Indicator Card is > 10 % when read at 23 °C ± 5 °C or 2a. or 2b. are not met. RECOMMENDED METHOD OF STORAGE 4. If baking is required, devices may be baked for: 192 hours at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen) or 96 hours at 60 °C ± 5 °C and < 5 % RH for all device containers or 24 hours at 125 °C ± 5 °C not suitable for reels or tubes Dry box storage is recommended as soon as the aluminum bag has been opened to prevent moisture absorption. The following conditions should be observed, if dry boxes are not available: Bag Seal Date: (If blank, see barcode label) Note: Level and body temperature defined by EIA JEDEC Standard J-STD-020 22522 • Storage temperature 10 °C to 30 °C EIA JEDEC standard J-STD-020 level 4 label is included on all dry bags • Storage humidity ≤ 60 % RH max. Rev. 1.2, 17-Apr-15 10 Document Number: 82495 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP753.., TSOP755.. www.vishay.com Vishay Semiconductors ESD PRECAUTION VISHAY SEMICONDUCTORS STANDARD BAR CODE LABELS Proper storage and handling procedures should be followed to prevent ESD damage to the devices especially when they are removed from the antistatic shielding bag. Electrostatic sensitive devices warning labels are on the packaging. The Vishay Semiconductors standard bar code labels are printed at final packing areas. The labels are on each packing unit and contain Vishay Semiconductors specific data. BAR CODE PRODUCT LABEL (example) 22178 Rev. 1.2, 17-Apr-15 11 Document Number: 82495 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000