VISHAY TSOP36233

TSOP362..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
FEATURES
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Continuous data transmission possible
1
2
3
e3
• TTL and CMOS compatibility
4
• Output active low
• Low power consumption
16797
• High immunity against ambient light
MECHANICAL DATA
• Supply voltage: 2.7 V to 5.5 V
Pinning
• Lead (Pb)-free component
1 = GND, 2 = GND, 3 = VS, 4 = OUT
• Component in accordance to RoHS 2002/95/EC and
WEEE 2002/96/EC
DESCRIPTION
The TSOP362.. series are miniaturized SMD-IR receiver
modules for infrared remote control systems. PIN diode and
preamplifier are assembled on lead frame, the epoxy
package is designed as IR filter.
The demodulated output signal can directly be decoded by a
microprocessor. TSOP362.. is the standard IR remote
control SMD-receiver series, for 3 V supply voltage
supporting all major transmission codes.
This component has not been qualified according to
automotive specifications.
SPECIAL FEATURES
• Improved immunity against ambient light
• Suitable burst length ≥ 10 cycles/burst
• Taping available for topview and sideview assembly
PARTS TABLE
CARRIER FREQUENCY
STANDARD APPLICATIONS (AGC2/AGC8)
30 kHz
TSOP36230
33 kHz
TSOP36233
36 kHz
TSOP36236
36.7 kHz
TSOP36237
38 kHz
TSOP36238
40 kHz
TSOP36240
56 kHz
TSOP36256
BLOCK DIAGRAM
APPLICATION CIRCUIT
17170
30 kΩ
VS
4
Input
AGC
Band
pass
Demo dulator
OUT
Transmitter
with
TSALxxxx
R 1 = 100 Ω
TSOPxxxx
VS
Circuit
3
+ VS
C1 =
4.7 µF
µC
OUT
GND
VO
GND
1; 2
PIN
16839
Document Number: 82187
Rev. 1.9, 19-Jun-08
Control circuit
GND
R1 and C1 recommended to suppress power supply
disturbances. The output voltage should not be
hold continuously at a voltage below VO = 2.0 V
by the external circuit.
www.vishay.com
211
TSOP362..
IR Receiver Modules for
Remote Control Systems
Vishay Semiconductors
ABSOLUTE MAXIMUM RATINGS (1)
PARAMETER
SYMBOL
VALUE
Supply voltage (pin 3)
TEST CONDITION
VS
- 0.3 to + 6.0
UNIT
V
Supply current (pin 3)
IS
3
mA
Output voltage (pin 1)
VO
- 0.3 to (VS + 0.3)
V
Output current (pin 1)
IO
10
mA
°C
Tj
100
Storage temperature range
Tstg
- 40 to + 100
°C
Operating temperature range
Tamb
- 25 to + 85
°C
Ptot
30
mW
Junction temperature
Tamb ≤ 85 °C
Power consumption
Note
(1) Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating condtions for extended periods may affect the device reliability.
ELECTRICAL AND OPTICAL CHARACTERISTICS (1)
PARAMETER
Supply current
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
Ev = 0
ISD
0.7
1.2
1.5
Ev = 40 klx, sunlight
ISH
Supply voltage
d
Output voltage low
IOSL = 0.5 mA, Ee = 0.7 mW/m2,
test signal see fig. 1
VOSL
Minimum irradiance
(30 to 40 kHz)
VS = 3 V, pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1
Ee min.
Minimum irradiance
(56 kHz)
VS = 3 V, pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1
Minimum irradiance
(30 to 40 kHz)
Transmission distance
mA
1.3
mA
2.7
VS
Ev = 0, test signal see fig. 1, IR diode TSAL6200,
IF = 250 mA
UNIT
5.5
V
35
m
250
mV
0.35
0.5
W/m2
Ee min.
0.4
0.6
W/m2
VS = 5 V, pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1
Ee min.
0.45
0.6
W/m2
Minimum irradiance
(56 kHz)
VS = 5 V, pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1
Ee min.
0.5
0.7
W/m2
Maximum irradiance
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3
Ee max.
Angle of half transmission distance
ϕ1/2
Directivity
W/m2
30
± 45
deg
Note
(1) T
amb = 25 °C, unless otherwise specified
TYPICAL CHARACTERISTICS
Tamb = 25 °C, unless otherwise specified
1.0
Optical Test Signal
t
tpi *
* tpi
VO
T
10/f0 is recommended for optimal function
Output Signal
1)
2)
VOH
16110
7/f0 < td < 15/f0
tpi - 5/f0 < tpo < tpi + 6/f 0
Output Pulse
0.9
(IR diode TSAL6200, IF = 0.4 A, 30 pulses, f = f0, t = 10 ms)
t po - Output Pulse Width (ms)
Ee
0.8
Input Burst Duration
0.7
0.6
0.5
0.4
0.3
0.2
= 950 nm,
optical test signal, fig. 1
0.1
0.0
VOL
td1 )
tpo2 )
16908
Fig. 1 - Output Function
www.vishay.com
212
0.1
t
1
10
100
1000
10 000
Ee - Irradiance (mW/m²)
Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
Document Number: 82187
Rev. 1.9, 19-Jun-08
TSOP362..
IR Receiver Modules for
Remote Control Systems
Optical Test Signal
600 µs
t
600 µs
t = 60 ms
94 8134
Output Signal, (see fig. 4)
VO
VOH
VOL
t on
4.0
Ee min. - Threshold Irradiance (mW/m2)
Ee
Correlation with ambient light sources:
10 W/m2 1.4 klx (Std.illum.A, T= 2855 K)
10 W/m2 8.2 klx (Daylight, T = 5900 K)
3.5
3.0
2.5
2.0
1.5
Ambient,
0.5
0.0
0.01
Fig. 3 - Output Function
Ton
0.7
0.6
0.5
Toff
0.3
= 950 nm,
optical test signal, fig. 3
0.1
0.0
0.1
1
10
100
1000
100
f = fo
1.5
f = 10 kHz
1.0
f = 100 Hz
0.0
0.1
1
10
100
1000
VsRMS - AC Voltage on DC Supply Voltage (mV)
16912
Fig. 4 - Output Pulse Diagram
f = 1 kHz
0.5
10 000
Ee - Irradiance (mW/m²)
16909
10
2.0
Ee min. - Threshold Irradiance (mW/m²)
Ton ,Toff - Output Pulse Width (ms)
0.9
0.2
1
Fig. 6 - Sensitivity in Bright Ambient
1.0
0.4
0.1
E - Ambient DC Irradiance (W/m 2)
16911
0.8
= 950 nm
1.0
t
t off
Vishay Semiconductors
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
Ee min. - Threshold Irradiance (mW/m²)
1.2
E e min./Ee - Rel. Responsivity
1.0
0.8
0.6
0.4
f = f0 ± 5 %
Δ f(3 dB) = f0/10
0.2
0.0
0.7
16925
0.9
1.1
f(E) = f0
1.6
1.2
0.8
0.4
0.0
0.0
1.3
f/f0 - Relative Frequency
Fig. 5 - Frequency Dependence of Responsivity
Document Number: 82187
Rev. 1.9, 19-Jun-08
2.0
94 8147
0.4
0.8
1.2
2.0
1.6
E - Field Strength of Disturbance (kV/m)
Fig. 8 - Sensitivity vs. Electric Field Disturbances
www.vishay.com
213
TSOP362..
IR Receiver Modules for
Remote Control Systems
Vishay Semiconductors
0°
0.8
10°
20°
30°
Max. Envelope Duty Cycle
0.7
0.6
40°
0.5
1.0
0.4
0.9
50°
0.8
60°
0.3
0.2
f = 38 kHz, Ee = 2
mW/m2
70°
0.7
0.1
80°
0.0
0
16913
20
40
60
80
100 120
Burst Length (number of cycles/burst)
0.6
0.4
Fig. 9 - Max. Envelope Duty Cycle vs. Burstlength
0
0.2
0.6
0.4
Fig. 12 - Directivity
1.0
0.6
0.9
0.5
Ee min. - Sensitivity (mW/m 2 )
Ee min. - Threshold Irradiance (mW/m²)
0.2
d rel - Relative Transmission Distance
16801
Sensitivity in dark ambient
0.4
0.3
0.2
0.1
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
2.0
0.0
- 30
- 15
0
15
30
45
60
75
90
Tamb - Ambient Temperature (°C)
16918
17185
Fig. 10 - Sensitivity vs. Ambient Temperature
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VS - Supply Voltage (V)
Fig. 13 - Sensitivity vs. Supply Voltage
S ( λ) rel - Relative Spectral Sensitivity
1.2
1.0
0.8
0.6
0.4
0.2
0.0
750
16919
850
950
1050
1150
λ - Wavelength (nm)
Fig. 11 - Relative Spectral Sensitivity vs. Wavelength
www.vishay.com
214
Document Number: 82187
Rev. 1.9, 19-Jun-08
TSOP362..
IR Receiver Modules for
Remote Control Systems
Vishay Semiconductors
The circuit of the TSOP362.. is designed so that unexpected
output pulses due to noise or disturbance signals are
avoided. A bandpass filter, an integrator stage and an
automatic gain control are used to suppress such
disturbances.
The distinguishing mark between data signal and
disturbance signal are carrier frequency, burst length and
duty cycle.
The data signal should fulfill the following conditions:
IR Signal
SUITABLE DATA FORMAT
IR Signal from Fluorescent
Lamp with Low Modulation
• Carrier frequency should be close to center frequency of
the bandpass (e.g. 38 kHz)
• Burst length should be 10 cycles/burst or longer
• After each burst which is between 10 cycles and 70 cycles
a gap time of at least 14 cycles is necessary
• For each burst which is longer than 1.8 ms a corresponding
gap time is necessary at some time in the data stream.
This gap time should be at least 6 times longer than the
burst
0
5
10
15
20
Time (ms)
16920
Fig. 14 - IR Signal from Fluorescent Lamp with Low Modulation
IR Signal from Fluorescent
Lamp with High Modulation
Some examples for suitable data format are: NEC code
(repetitive pulse), NEC code (repetitive data), Toshiba
Micom Format, Sharp code, RC5 Code, RC6 code,
R-2000 code, Sony code.
When a disturbance signal is applied to the TSOP362.. it can
still receive the data signal. However the sensitivity is
reduced to that level that no unexpected pulses will occur.
Some examples for such disturbance signals which are
suppressed by the TSOP362.. are:
• DC light (e.g. from tungsten bulb or sunlight)
• Continuous signal at 38 kHz or at any other frequency
IR Signal
• Up to 800 short bursts per second can be received
continuously
0
16921
10
10
15
20
Time (ms)
Fig. 15 - IR Signal from Fluorescent Lamp with High Modulation
• Signals from fluorescent lamps with electronic ballast with
high or low modulation (see figure 14 or 15)
Document Number: 82187
Rev. 1.9, 19-Jun-08
www.vishay.com
215
TSOP362..
Vishay Semiconductors
IR Receiver Modules for
Remote Control Systems
PACKAGE DIMENSIONS in millimeters
16629
ASSEMBLY INSTRUCTIONS
Reflow Soldering
• Reflow soldering must be done within 72 h while stored
under a max. temperature of 30 °C, 60 % RH after opening
the dry pack envelope
• Set the furnace temperatures for pre-heating and heating
in accordance with the reflow temperature profile as shown
in the diagram. Excercise extreme care to keep the
maximum temperature below 260 °C. The temperature
shown in the profile means the temperature at the device
surface. Since there is a temperature difference between
the component and the circuit board, it should be verified
that the temperature of the device is accurately being
measured
www.vishay.com
216
• Handling after reflow should be done only after the work
surface has been cooled off
Manual Soldering
• Use a soldering iron of 25 W or less. Adjust the
temperature of the soldering iron below 300 °C
• Finish soldering within 3 s
• Handle products only after the temperature has cooled off
Document Number: 82187
Rev. 1.9, 19-Jun-08
TSOP362..
IR Receiver Modules for
Remote Control Systems
Vishay Semiconductors
VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE
300
max. 260 °C
245 °C
255 °C
240 °C
217 °C
250
T (°C)
200
max. 20 s
150
max. 100 s
max. 120 s
100
max. Ramp Up 3 °C/s
max. Ramp Down 6 °C/s
50
0
0
19800
50
100
150
t (s)
200
250
300
max. 2 cycles allowed
TAPING VERSION TSOP..TT Dimensions in millimeters
16584
Document Number: 82187
Rev. 1.9, 19-Jun-08
www.vishay.com
217
TSOP362..
Vishay Semiconductors
IR Receiver Modules for
Remote Control Systems
TAPING VERSION TSOP..TR Dimensions in millimeters
16585
www.vishay.com
218
Document Number: 82187
Rev. 1.9, 19-Jun-08
TSOP362..
IR Receiver Modules for
Remote Control Systems
Vishay Semiconductors
REEL DIMENSIONS in millimeters
16734
LEADER AND TRAILER Dimensions in millimeters
Trailer
no devices
Leader
devices
no devices
End
Start
min. 200
min. 400
96 11818
COVER TAPE PEEL STRENGTH
LABEL
According to DIN EN 60286-3
0.1 to 1.3 N
300 ± 10 mm/min.
165° to 180° peel angle
Standard bar code labels for finished goods
Document Number: 82187
Rev. 1.9, 19-Jun-08
The standard bar code labels are product labels and used for
identification of goods. The finished goods are packed in final
packing area. The standard packing units are labeled with
standard bar code labels before transported as finished
goods to warehouses. The labels are on each packing unit
and contain Vishay Semiconductor GmbH specific data.
www.vishay.com
219
TSOP362..
Vishay Semiconductors
IR Receiver Modules for
Remote Control Systems
VISHAY SEMICONDUCTOR GMBH STANDARD BAR CODE PRODUCT LABEL (Finished Goods)
PLAIN WRITING
ABBREVIATION
LENGTH
Item-description
-
18
Item-number
INO
8
Selection-code
SEL
3
BATCH
10
Data-code
COD
3 (YWW)
Plant-code
PTC
2
Quantity
QTY
8
Accepted by
ACC
-
Packed by
PCK
-
LOT-/serial-number
Mixed code indicator
MIXED CODE
-
xxxxxxx+
Company logo
Origin
TYPE
LENGTH
Item-number
LONG BAR CODE TOP
N
8
Plant-code
N
2
Sequence-number
X
3
Quantity
N
8
Total length
-
21
TYPE
LENGTH
SHORT BAR CODE BOTTOM
Selection-code
X
3
Data-code
N
3
Batch-number
X
10
Filter
-
1
Total length
-
17
DRY PACKING
The reel is packed in an anti-humidity bag to protect the
devices from absorbing moisture during transportation and
storage.
Aluminum bag
Label
After more than 72 h under these conditions moisture
content will be too high for reflow soldering.
In case of moisture absorption, the devices will recover to the
former condition by drying under the following condition:
192 h at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen)
or
96 h at 60 °C + 5 °C and < 5 % RH for all device containers or
24 h at 125 °C + 5 °C not suitable for reel or tubes.
An EIA JEDEC standard JESD22-A112 level 4 label is
included on all dry bags.
Reel
15973
FINAL PACKING
The sealed reel is packed into a cardboard box. A secondary
cardboard box is used for shipping purposes.
RECOMMENDED METHOD OF STORAGE
Dry box storage is recommended as soon as the aluminum
bag has been opened to prevent moisture absorption. The
following conditions should be observed, if dry boxes are not
available:
16943
• Storage temperature 10 °C to 30 °C
• Storage humidity ≤ 60 % RH max.
www.vishay.com
220
Example of JESD22-A112 level 4 label
Document Number: 82187
Rev. 1.9, 19-Jun-08
TSOP362..
IR Receiver Modules for
Remote Control Systems
ESD PRECAUTION
Proper storage and handling procedures should be followed
to prevent ESD damage to the devices especially when they
are removed from the antistatic shielding bag. Electro-static
sensitive devices warning labels are on the packaging.
Vishay Semiconductors
VISHAY SEMICONDUCTORS STANDARD
BAR CODE LABELS
The Vishay Semiconductors standard bar code labels are
printed at final packing areas. The labels are on each
packing unit and contain Vishay Semiconductors specific
data.
16962
Document Number: 82187
Rev. 1.9, 19-Jun-08
www.vishay.com
221
TSOP362..
Vishay Semiconductors
IR Receiver Modules for
Remote Control Systems
OZONE DEPLETING SUBSTANCES POLICY STATEMENT
It is the policy of Vishay Semiconductor GmbH to
1. Meet all present and future national and international statutory requirements.
2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with
respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment.
It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone
depleting substances (ODSs).
The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use
within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances.
Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in
the following documents.
1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively.
2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency
(EPA) in the USA.
3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively.
Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do
not contain such substances.
We reserve the right to make changes to improve technical design
and may do so without further notice.
Parameters can vary in different applications. All operating parameters must be validated for each customer application by the
customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall
indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any
claim of personal damage, injury or death associated with such unintended or unauthorized use.
Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany
www.vishay.com
222
Document Number: 82187
Rev. 1.9, 19-Jun-08
Legal Disclaimer Notice
Vishay
Disclaimer
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 18-Jul-08
www.vishay.com
1