VISHAY VSOP58438

VSOP584..
www.vishay.com
Vishay Semiconductors
Preamplifier Circuit for IR Remote Control
FEATURES
• Narrow bandpassfilter for all common carrier
frequencies
• High immunity against DC light
• Intelligent AGC to suppress disturbance from fluorescent
lamps and CRTs
• Low power consumption
• Wide supply voltage range
• High immunity against ripple on the supply voltage
• Output active low
• IC manufactured in CMOS technology
22529
• Small QFN package with 2 mm width
• Compliant to RoHS Directive 2002/95/EC
MECHANICAL DATA
Note
** Please see document “Vishay Material Category Policy”:
www.vishay.com/doc?99902
Pinning:
1, 4, 5= N.C.,
2 = VS,
3 = OUT,
6, 8 = GND,
7 = IN
DESCRIPTION
The VSOP584.. is designed for use in an IR receiver
application together with a photo pin diode. It is a
sophisticated receiver concept that is very sensitive to data
signals and compatible with the most common data formats
for IR remote control. On the other hand it is immune to DC
current caused by DC light sources such as tungsten bulbs.
The disturbance signal of fluorescent lamps is suppressed;
there are no unwanted pulses at the output.
PARTS TABLE
CARRIER FREQUENCY
PART NUMBER
36 kHz
VSOP58436
38 kHz
VSOP58438
Note
• Circuits for other carrier frequencies are available on request.
BLOCK DIAGRAM (simplified)
APPLICATION CIRCUIT
100 Ω
+ VS
Bias
Input, from
photodiode
Controlled
gain
amplifier
Automatic
threshold Intecontrol
grator
33 kΩ
VS
VSOP584..
IN
OUT
Output,
to μC
Bandpassfilter
Automatic
gain
control
GND
0.22 μF
VS = 2.7 V
to 5.5 V
Microcontroller
or other logic
to decode the
IR signal
0V
GND
The RC filter is optional to improve the EOS robustness
and the immunity to supply voltage ripple. We recommend
to keep the distance between the photodiode and the input
of the VSOP584.. as short as possible.
21537-5
21536-3
Vishay recommends using a photodiode with at least
2.3 mm2 area. The connection between the photodiode and
pin 7 should be kept as short as possible and carefully
shielded to prevent noise coupling.
Rev. 1.2, 11-Jan-12
1
Document Number: 82444
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VSOP584..
www.vishay.com
Vishay Semiconductors
ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
Supply voltage
Pin 2
VS
- 0.3 to + 6
V
mA
Supply current
Pin 2
IS
5
Output voltage
Pin 3
VO
- 0.3 to (VS + 0.3)
V
Output sink current
Pin 3
IO
5
mA
Tamb ≤ 85 °C
Power dissipation
Ptot
10
mW
Operating temperature range
Tamb
- 25 to + 85
°C
Storage temperature range
Tstg
- 25 to + 85
°C
Pin 2, pin 3, MIL-STD-883C
VESD
2000
V
Pin 7, MIL-STD-883C
VESD
500
V
Pin 2, pin 3, MIL-STD-883C
VESD
200
V
Pin 7, MIL-STD-883C
VESD
100
V
ESD stress, HBM
ESD stress, MM
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability.
ELECTRICAL CHARACTERISTICS (Tamb = - 30 °C to + 85 °C)
PARAMETER
TEST CONDITION
SYMBOL
MIN.
VS
2.7
0.65
Supply voltage
IIN = 0, VS = 5 V
IS
Output voltage low (pin 3)
Supply current (pin 2)
IOL = 2 mA
VOL
Output voltage high (pin 3)
IOL = 0
VOH
Internal pull up resistor
(pin 2, pin 3)
0.85
MAX.
UNIT
5.5
V
1.05
mA
100
mV
VS - 0.25
RPU
Max. input DC current
TYP.
V
33
kΩ
VIN > 0
IIN-DCmax.
IIN-DC = 0, fC = fBPF
IIN-min.
700
1000
pA
IIN-DC = 100 μA, fC = fBPF
IIN-min.
5
10
nA
IIN-DC = 0, fC = fBPF,
IIN = 0.8 nA to 50 μA,
testsignal see fig. 1, BER ≤ 2%
tpo
tpi - 6/f0
tpi
tpi + 6/f0
μs
Accuracy of bandpass center
frequency
Tamb = + 25 °C
fBPF
f0 - 4 %
f0
f0 + 4 %
kHz
Bandwidth of bandpassfilter
- 3 dB, f0 = 38 kHz
B
Min. signal detection current
Output pulse width
IIN
400
μA
3.8
kHz
burst length tpI
VOUT
output pulse width tpo
one carrier cycle 1/fC
IIN
burst length of input signal tpi
output pulse width tpo
21538
VOUT
Fig. 1 - Testsignal
Rev. 1.2, 11-Jan-12
2
Document Number: 82444
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VSOP584..
www.vishay.com
Vishay Semiconductors
IIN-min. - Minimum Detection Current (nA)
TYPICAL CHARACTERISTICS (Tamb = 25 °C, VS = 3.3 V, unless otherwise specified)
1.0
Output Pulse Width (ms)
0.9
tpo
0.8
0.7
0.6
0.5
TOFF
0.4
0.3
0.2
Testsignal: tpi = 0.6 ms
0.1
burst repetition time = 1.2 ms
0
0.1
10
21539
1000
4.5
4.0
3.5
3.0
2.0
1.5
1.0
f = 10 kHz
0.5
f = 100 Hz
0
1
100 000
IIN-min. - Minimum Detection Current (nA)
4.0
3.5
Wavelength of ambient
illumination: λ = 950 nm
2.5
2.0
1.5
1.0
0.5
0.1
1
1000
10
100
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
- 30
DC Input Current (µA)
- 10
10
30
50
70
90
Tamb - Ambient Temperature (°C)
Fig. 3 - Sensitivity vs. DC Input Current
Fig. 6 - Sensitivity vs. Temperature
2.5
0.8
Maximum Envelope Duty Cycle
IIN-min. - Minimum Detection Current (nA)
100
Fig. 5 - Suppression of Ripple on Supply Voltage
4.5
0
0.01
10
ΔVS - AC Ripple on DC Supply Voltage (mVPP)
5.0
3.0
f = fO
2.5
IIN - Input Current (nA)
Fig. 2 - Output Pulse Diagram
IIN-min. - Minimum Detection Current (nA)
5.0
VSOP58438
2.0
1.5
1.0
0.5
0
0.7
0.6
0.5
0.4
0.3
IIN = 5 nA
0.2
0.1
0
32
34
36
38
40
42
44
0
Frequency (kHz)
Fig. 4 - Bandpassfilter Characteristic
Rev. 1.2, 11-Jan-12
50
100
150
Burstlength (Number of Cycles/Burst)
Fig. 7 - Maximum Envelope Duty Cycle
3
Document Number: 82444
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VSOP584..
www.vishay.com
Vishay Semiconductors
PACKAGE DIMENSIONS in millimeters
2
Marking area
2
3338
YWW
1.6 ± 0.15
Pinning:
1. n.c.
2. VS
3. Out
4. n.c.
5. n.c.
6. GND
7. IN
8. GND
0.9 ± 0.15
0.25 x 45°
Chamfered corner
PIN 1 indicator
1. Coplanarity (0.1 mm)
applies to the exposed
pad as well as the
exposed terminals.
2. Package dimension does not
include mold flash, protrusions,
burrs, or metal smearing.
0.76 ± 0.05
0.2 ref.
PIN 1
indicator
(8x)
0.25 ± 0.05
0.2 min.
(8x)
0.3 ± 0.1
Exposed pad
Proposed hole layout
from component side
(for reference only)
0.5 typ. (6x)
10:1
(8x)
0.65
Technical drawings
according to DIN
specifications
0.35 (8x)
1.3
Not indicated tolerances ± 0.1
Drawing-No.: 6.550-5314.01-4
Issue: 2; 07.11.11
0.5 (6x)
ASSEMBLY INSTRUCTIONS
Reflow Soldering
• Set the furnace temperatures for pre-heating and heating
in accordance with the reflow temperature profile as
shown in the diagram. Excercise extreme care to keep the
maximum temperature below 260 °C. The temperature
shown in the profile means the temperature at the device
surface. Since there is a temperature difference between
the component and the circuit board, it should be verified
that the temperature of the device is accurately being
measured
Manual Soldering
• Use a soldering iron of 25 W or less. Adjust the
temperature of the soldering iron below 300 °C
• Finish soldering within 3 s
• Handle products only after the temperature has cooled
off.
• Handling after reflow should be done only after the work
surface has been cooled off
Rev. 1.2, 11-Jan-12
4
Document Number: 82444
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VSOP584..
www.vishay.com
Vishay Semiconductors
VISHAY LEAD (PB)-FREE REFLOW SOLDER PROFILE
300
max. 260 °C
245 °C
255 °C
240 °C
217 °C
250
T (°C)
200
max. 20 s
150
max. 100 s
max. 120 s
100
max. Ramp Up 3 °C/s
max. Ramp Down 6 °C/s
50
0
0
19800
50
100
150
t (s)
200
250
300
max. 2 cycles allowed
TAPING VERSION VSOP DIMENSIONS in millimeters
Rev. 1.2, 11-Jan-12
5
Document Number: 82444
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VSOP584..
www.vishay.com
Vishay Semiconductors
REEL DIMENSIONS in millimeters
Reel Width
Reel
Size
22610
REEL
REEL SIZE (inch)
REEL WIDTH (mm)
TRAILER LENGTH (mm)
LEADER LENGTH (mm)
QANTITY PER REEL
7
8.4
160
400
3000
LABEL
Standard bar code labels for finished goods
The standard bar code labels are product labels and used
for identification of goods. The finished goods are packed in
final packing area. The standard packing units are labeled
with standard bar code labels before transported as finished
goods to warehouses. The labels are on each packing unit
and contain Vishay Semiconductor GmbH specific data.
VISHAY SEMICONDUCTOR GMBH STANDARD BAR CODE PRODUCT LABEL (finished goods)
PLAIN WRITTING
ABBREVIATION
LENGTH
-
18
Item-number
INO
8
Selection-code
SEL
3
BATCH
10
Data-code
COD
3 (YWW)
Plant-code
PTC
2
Quantity
QTY
8
Accepted by
ACC
-
Packed by
PCK
-
Item-description
LOT-/serial-number
Mixed code indicator
Origin
LONG BAR CODE TOP
MIXED CODE
-
xxxxxxx+
Company logo
TYPE
LENGTH
Item-number
N
8
Plant-code
N
2
Sequence-number
X
3
Quantity
N
8
Total length
-
21
SHORT BAR CODE BOTTOM
TYPE
LENGTH
Selection-code
X
3
Data-code
N
3
Batch-number
X
10
Filter
-
1
Total length
-
17
Rev. 1.2, 11-Jan-12
6
Document Number: 82444
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VSOP584..
www.vishay.com
Vishay Semiconductors
ESD PRECAUTION
VISHAY SEMICONDUCTORS STANDARD
BAR CODE LABELS
Proper storage and handling procedures should be followed
to prevent ESD damage to the devices especially when they
are removed from the antistatic shielding bag. Electro-static
sensitive devices warning labels are on the packaging.
The Vishay Semiconductors standard bar code labels are
printed at final packing areas. The labels are on each
packing unit and contain Vishay Semiconductors specific
data.
16962
Rev. 1.2, 11-Jan-12
7
Document Number: 82444
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Revision: 12-Mar-12
1
Document Number: 91000