Custom Networks Vishay Techno Custom Thick Film Resistor Networks, Single-In-Line (Molded or Conformal Coated SIPs) and Dual-In-Line (Molded DIPs) FEATURES • Custom resistor, capacitor, diode and inductor network combinations • R, C, L, D multicomponent networks • Processed to MIL-PRF-83401 • Fast turnaround time • Unlimited schematics possible • Design through production • High temperature solder joints • Wide resistance range • Ultra high precision laser trimming • Double sided printing and through holes/VIAs • High density circuit designs • Tighter parameters available • High power ratings available SCHEMATICS DIPS 16 SIPS, Molded 15 14 R2 13 R4 12 R5 11 10 R7 R7 R10 R2 R6 R8 R3 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 R10 R R R R14 11 12 13 R15 R4 R1 2 13 3 1 2 3 4 5 6 7 L1 8 9 10 CR4 GND XDCR R3 R4 R5 CR3 D1 R6 + 5 V CONTROL PREAMP 30K 11K 75K R3 R4 C3 0.001 R5 µF 100K 1000K R2 R5 R7 R8 R9 10K D2 R1 R2 R5 R6 5 11 10 R8 R9 C2 0.1 µF R8 6 7 9 8 75K R6 R7 0.01 470 Ω 11K C1 µF D3 R7 4 12 R4 R8 CR1 R16 R4 R3 R2 R3 C2 R1 R2 CR2 R1 R6 R11 1 14 C1 R1 R3 1 R9 R5 R9 R1 R 9 SIPS, Coated 9 1 2 3 4 5 6 7 8 9 10 1 2 8 3 4 5 6 7 8 9 10 11 12 13 0.10 µF 0.10 µF R2 R12 R3 R4 R1 1 R6 R7 R5 2 3 R9 5 R3 R2 R4 R6 R5 R8 R9 100K 0.10 µF 5.1K R11 6 7 0.10 µF 150K 150 1M 300K pF 200K R7 R10 R8 4 R1 1 2 3 4 5 6 7 8 9 10 1M 5.1K 150 pF 330 Ω 1K 5.1K 1 2 3 4 5 6 7 8 9 10 1 1M 220 Ω 1 12 13 14 ELECTRICAL SPECIFICATIONS MECHANICAL SPECIFICATIONS Resistance Range: 1 Ω to 50 MΩ Tolerance: ± 0.5 % available Temperature Coefficient: ± 100 ppm/°C available TCR Tracking: ± 50 ppm/°C available Ratio Matching: ± 0.5 % available Power Rating (Element): 1/8 W at + 70 °C typical Resistive Element: Thick film Solder Joints: High temperature Sn10 Encapsulation: Thermoset epoxy for molded. Epoxy for conformal coated Lead Lengths: 0.060" (1.52 mm) to 0.190" (4.83 mm) molded, 0.060" (1.52 mm) to 0.290" (7.37 mm) coated Substrates: 96 % alumina, Thicknesses: 0.020" (0.508 mm) to 0.040" (1.016 mm) Resistor Coatings: Glass passivation, dielectrics for crossovers ENVIRONMENTAL SPECIFICATIONS Temperature Limits: - 65 °C to + 125 °C Document Number: 68009 Revision: 03-Mar-10 For technical questions, contact: [email protected] www.vishay.com 25 Custom Networks Custom Thick Film Resistor Networks, Single-In-Line (Molded or Conformal Coated SIPs) and Dual-In-Line (Molded DIPs) Vishay Techno DIMENSIONS in inches (millimeters) DIPS 0.045 ± 0.020 (1.14 ± 0.508) A max. 0.300 (7.62) B max. 0.260 (6.60) C max. Pin #1 Identifier 0.020 ± 0.002 (0.508 ± 0.051) 0.100 ± 0.005 (2.54 ± 0.127) Non-cumulative SIPS, Molded SIPS, Coated D max. A max. Pin #1 identifier 0.018 ± 0.003 (0.457 ± 0.076) Pin #1 identifier 0.015 (0.381) min. B max. C max. 0.020 ± 0.003 (0.508 ± 0.076) D max. A max. B max. C max. 0.010 ± 0.005 (2.54 ± 0.127) Non-cumulative MODEL No. of Pins DIPS 14 DIPS 16 SIPS, molded, low profile 6 SIPS, molded, low profile 8 SIPS, molded, low profile 10 SIPS, molded, high profile 6 SIPS, molded, high profile 8 SIPS, molded, high profile 10 SIPS, coated 2 SIPS, coated 3 thru 19 SIPS, coated 20 Note (1) Depending on customer requirements 0.100 ± 0.005 (2.54 ± 0.127) Non-cumulative 0.018 ± 0.002 (0.457 ± 0.051) A (max.) 0.775 (19.69) 0.875 (22.23) 0.598 (15.19) 0.798 (20.27) 0.998 (25.35) 0.598 (15.19) 0.798 (20.27) 0.998 (25.35) 0.200 (5.08) B (max.) 0.190 (4.83) 0.190 (4.83) 0.192 (4.88) 0.192 (4.88) 0.192 (4.88) 0.340 (8.64) 0.340 (8.64) 0.340 (8.64) 0.200 (5.08) (1) (1) 2.00 (50.80) (1) C (max.) 0.135 (3.43) 0.135 (3.43) 0.190 (4.83) 0.190 (4.83) 0.190 (4.83) 0.190 (4.83) 0.190 (4.83) 0.190 (4.83) 0.290 (7.37) 0.290 (7.37) 0.290 (7.37) D (max.) 0.088 (2.23) 0.088 (2.23) 0.088 (2.23) 0.088 (2.23) 0.088 (2.23) 0.088 (2.23) 0.100 (2.54) (1) (1) ENVIRONMENTAL PERFORMANCE TEST (2) Power Conditioning Thermal Shock Thermal Shock Group C Short Time Overload Low Temperature Storage Low Temperature Operation Low Temperature Exposure Moisture Resistance Resistance to Soldering Heat Shock Vibration Load life (108) (107) (107) (106) (210) (213) (204) (108) Maximum ΔR (TYPICAL TEST LOTS) ΔR < 0.10 % ΔR < 0.10 % ΔR < 0.10 % ΔR < 0.03 % ΔR < 0.02 % ΔR < 0.02 % ΔR < 0.06 % ΔR < 0.10 % ΔR < 0.10 % ΔR < 0.04 % ΔR < 0.04 % ΔR < 0.22 % Note (2) Numbers in parentheses refer to test method MIL-STD-202 as modified by the detail specification ORDERING INFORMATION • For custom product information contact factory www.vishay.com 26 For technical questions, contact: [email protected] Document Number: 68009 Revision: 03-Mar-10 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000