Full Specification

LM0302H Series
SMD Power Choke Coil
SMD Power Choke Coil
PIC0302H Series
1. PART NO. EXPRESSION :
LM 0 3 0 2 H 1 R 5 M F - □□
(a)
(b)
(c)
(d)
(e)(f)
(g)
(a) Series code
(d) Inductance code : 1R5 = 1.5uH
(b) Dimension code
(e) Tolerance code : M = ± 20%
(c) Type code
(f) F : RoHS Compliant
(g) 11~99 : Internal controlled number
2. CONFIGURATION & DIMENSIONS :
A
C
D
L
G
H
E
B
1.5
Unit:m/m
A
B
C
D
E
G
H
L
3.5± 0.2
3.2± 0.2
1.8± 0.2
0.7± 0.2
1.2± 0.2
1.9 Ref
1.45 Ref
4.1 Ref
3. SCHEMATIC :
4. MATERIALS :
d
e
(a) Core : Carbonyl Powder.
(b) Wire : Polyester Wire or equivalent
(c) Solder Plating : 100% Pb free solder
(d) Ink : Halogen-free ketone
a
c
b
(e) Paint : Epoxy resin
5. GENERAL SPECIFICATION :
a) Test Freq. : L : 100KHz/1.0V
b) Ambient Temp. : 25° C
c) Operating Temp. : -40° C to +125° C
d) Storage Temp. : -10° C to + 40° C
e) Humidity Range : 50 ~ 60% RH (Product without taping)
f) Heat Rated Current (Irms) will cause the coil temperature rise approximately Δt of 40°C (keep 1min.)
g) Saturation Current (Isat) will cause L0 to drop 30% typical. (keep quickly).
h) Part Temperature (Ambient+Temp. Rise) : Should not exceed 125° C under worst case operating conditions.
Pb
NOTE : Specifications subject to change without notice. Please check our website for latest information.
800.729.2099 tel
www.icecomponents.com
31.10.2013
(01/14) LM0302H-1
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 1
LM0302H Series
SMD Power Choke Coil
SMD Power Choke Coil
PIC0302H Series
6. ELECTRICAL CHARACTERISTICS :
Part No.
Inductance L
( μH ) ±20%
@ 0A
LM0302HR47MF
Irms
(A)
Typ.
Isat
(A)
Typ.
DCR
( mΩ )
Typ. @ 25° C
DCR
( mΩ )
Max. @ 25° C
0.47
7.0
9.0
19.7
23
LM0302HR68MF
0.68
5.5
7.0
25.5
29
LM0302H1R0MF
1.00
4.0
5.0
32
38
LM0302H1R5MF
1.50
3.8
4.0
42
50
LM0302H2R2MF
2.20
3.5
3.7
65
75
LM0302H3R3MF
3.30
3.0
3.5
125
145
LM0302H4R7MF
4.70
2.6
3.0
172
200
LM0302H5R6MF
5.60
2.2
2.6
205
238
LM0302H6R8MF
6.80
1.9
2.2
260
300
LM0302H8R2MF
8.20
1.6
1.9
340
390
LM0302H100MF
10.0
1.4
1.6
366
422
0
Pb
NOTE : Specifications subject to change without notice. Please check our website for latest information.
800.729.2099 tel
www.icecomponents.com
31.10.2013
(01/14) LM0302H-2
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 2
LM0302H Series
SMD Power Choke Coil
SMD Power Choke Coil
PIC0302H Series
7. CHARACTERISTICS CURVES :
40
0 .8
40
0. 48
30
0 .6
30
0. 32
20
0 .4
20
0. 16
10
0 .2
10
0
3. 6
5.4
DC CURRENT(A)
7. 2
LM0302H1R0MF-□□
TM P C 0302H -1R 0
2
0
9
37
1.2
22.2
0.8
14.8
0.4
7.4
TEMP. RISE(oC)
29.6
0
0.9
1. 8
2.7
3. 6
1. 4
0
4. 5
1.5
9
1
6
0.5
3
0
0. 8
48
0 .8
24
0
0
5. 6
7
INDUCTANCE (uH)
1 .6
TEMP. RISE(oC)
INDUCTANCE (uH)
72
4.2
1. 6
2.4
3. 2
LM0302H3R3MF-□□
TMPC0302H-3R3
6
12 0
2 .4
2. 8
15
12
0
96
DC CURRENT(A)
DC CURRENT(A)
7
0
3 .2
1. 4
5. 6
4
DC CURRENT(A)
LM0302H2R2MF-□□
TMPC0302H-2R2
0
4.2
2
DC CURRENT(A)
4
2. 8
LM0302H1R5MF-□□
TMPC0302H-1R5
2.5
1.6
0
0
0
150
4.8
120
3.6
90
2.4
60
1.2
30
0
0
0. 7
1. 4
2.1
2. 8
TEMP. RISE(oC)
1. 8
INDUCTANCE (uH)
0
50
TEMP. RISE(oC)
INDUCTANCE (uH)
0. 64
TEMP. RISE(oC)
INDUCTANCE (uH)
1
0
INDUCTANCE (uH)
LM0302HR68MF-□□
TMPC0302H-R68
50
TEMP. RISE(oC)
LM0302HR47MF-□□
TMPC0302H-R47
0 .8
0
3. 5
DC CURRENT(A)
Pb
NOTE : Specifications subject to change without notice. Please check our website for latest information.
800.729.2099 tel
www.icecomponents.com
31.10.2013
(01/14) LM0302H-3
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 3
LM0302H Series
SMD Power Choke Coil
SMD Power Choke Coil
PIC0302H Series
7. CHARACTERISTICS CURVES :
20
8
40
4 .8
15
6
30
3 .2
10
4
20
1 .6
5
2
10
0
0
0. 6
1. 2
1.8
2. 4
3
0
0
DC CURRENT(A)
0.52
1.04
1. 56
2.08
2. 6
DC CURRENT(A)
LM0302H6R8MF-□□
TMPC0302H-6R8
LM0302H8R2MF-□□
TMPC0302H-8R2
8
40
9 .6
32
6
30
7 .2
24
4
20
4 .8
16
2
10
2 .4
8
0
0.44
0.88
1. 32
1.76
0
0
2. 2
0.38
LM0302H100MF-□□
TMPC0302H-100
0.76
1. 14
1.52
1. 9
DC CURRENT(A)
DC CURRENT(A)
20
16
16
12
12
8
8
4
4
0
TEMP. RISE(oC)
20
40
0
0
0
INDUCTANCE (uH)
12
TEMP. RISE(oC)
50
10
INDUCTANCE (uH)
50
TEMP. RISE(oC)
INDUCTANCE (uH)
0
INDUCTANCE (uH)
6 .4
TEMP. RISE(oC)
10
0
INDUCTANCE (uH)
LM0302H5R6MF-□□
TMPC0302H-5R6
25
TEMP. RISE(oC)
LM0302H4R7MF-□□
TMPC0302H-4R7
8
0
0
0.32
0.6 4
0. 96
1.28
1. 6
DC CURRENT(A)
Pb
NOTE : Specifications subject to change without notice. Please check our website for latest information.
800.729.2099 tel
www.icecomponents.com
31.10.2013
(01/14) LM0302H-4
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 4
LM0302H Series
SMD Power Choke Coil
SMD Power Choke Coil
PIC0302H Series
8. RELIABILITY AND TEST CONDITION
ITEM
PERFORMANCE
TEST CONDITION
Electrical Characteristics Test
Refer to standard electrical characteristics list
Inductance
DCR
HP4284A, CH11025, CH3302, CH1320, CH1320S
LCR meter.
CH16502, Agilent33420A Micro-Ohm Meter.
Heat Rated Current (Irms)
Approximately ΔT≦ 40°C
Irms(A) will cause the coil temperature rise
approximately ΔT(°C) without core loss
1. Applied the allowed DC current(keep 1min).
2. Temperature measured by digital surface thermometer
Saturation Current (Isat)
ΔL30% typical.
Isat(A) will cause Lo to drop ΔL(%) (keep quickly).
Electric specification should be satisfied
Temperature : 125± 2° C
Time : 1000± 12 hours
Measured at room temperature after placing for 2 to 3hrs
(MIL-PRF-27)
Reliability Test
High Temperature
Exposure Test
Low Temperature
Life Test
Temperature : -40± 2° C
Time : 500± 12 hours
Measured at room temperature after placing for 2 to 3hrs
Thermal Shock Test
Conditions of 1 cycle.
Step
Temperature (° C)
1
-40+0/-2
Times (min.)
15± 1
2
Room Temperature
Within <0.2
3
+125+2/-0
15± 1
Total : 300 cycles
Measure at room temperature after placing for 2 to 3 hrs.
(AEC-Q200-REV C)
Humidity Resistance
Temperature : 85± 2° C
Humidity : 85± 3% RH
Time : 1000± 12 hours
Measured at room temperature after placing for 2 to 3hrs
(AEC-Q200-REV C)
Vibration Test
Frequency : 10-2000-10Hz for 20min.
Amplitude: Parts mounted within 2" from any secure point.
Directions and times : X, Y, Z directions for 20 min.
This cycle shall be performed 12 times in each of three
mutually perpendicular directions.
(Total 12 hours)
(MIL-STD-202 Method 204 D Test condition B)
Reflow Test
Solder test
Preheat : 150± 5° C
Duration : 5 minutes
Temperature : 260± 5° C, 20~40 seconds
(IPC/JEDEC J-STD-020C)
Terminals should be covered by over 95%
solder on visual inspection.
After dip into flux,dip into solder
235± 5° C, 4± 1seconds
Flux, solder for lead free
(ANSI/J-STD-002C Method B)
Pb
NOTE : Specifications subject to change without notice. Please check our website for latest information.
800.729.2099 tel
www.icecomponents.com
31.10.2013
(01/14) LM0302H-5
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 5
LM0302H Series
SMD Power Choke Coil
SMD Power Choke Coil
PIC0302H Series
9. SOLDERING AND MOUNTING :
9-1. Recommended PC Board Pattern
4.1
1.45
1.9
9-2. Soldering
Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused
by the difference in coefficients of expansion between solder, chip and substrate. Our terminations are suitable for all
wave and re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot
air soldering tools.
9-2.1 Solder Re-flow :
Recommended temperature profiles for re-flow soldering in Figure 1.
9-2.2 Soldering Iron (Figure 2) :
Products attachment with soldering iron is discouraged due to the inherent process control limitations.
In the event that a soldering iron must be employed the following precautions are recommended.
Note :
a) Preheat circuit and products to 150° C.
b) 355° C tip temperature (max)
c) Never contact the ceramic with the iron tip
d) 1.0mm tip diameter (max)
e) Use a 20 watt soldering iron with tip diameter of 1.0mm
f) Limit soldering time to 4~5 secs.
Soldering
20~40s
Natural
cooling
Preheating
TEMPERATURE ° C
TEMPERATURE ° C
Preheating
TP(26 0° C/40 s max.)
217
200
150
60~150s
60~180s
25
4 80s max.
Soldering
Natural
cooling
350
150
Time(sec.)
G rad ual
Cooling
O ve r 1min.
Within 4-5s
Figure 1. Re-flow Soldering: 3 times max.
Figure 2. Iron Soldering: 1 times max.
Pb
NOTE : Specifications subject to change without notice. Please check our website for latest information.
800.729.2099 tel
www.icecomponents.com
31.10.2013
(01/14) LM0302H-6
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 6
LM0302H Series
SMD Power Choke Coil
SMD Power Choke Coil
PIC0302H Series
10. PACKAGING INFORMATION :
10-1. Reel Dimension
COVER TAPE
ØC
B
D
2.0± 0.5
A
EMBOSSED CARRIER
Type
A(mm)
B(mm)
C(mm)
D(mm)
13" x 12mm
12.0± 0.5
100± 2.0
13.5± 0.5
330
2.0
1.5
t
Bo
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
P
W
F
4.0
1.75
10-2 Tape Dimension
Ko
3°
Ao
Series
Ao(mm)
Bo(mm)
Ko(mm)
P(mm)
W(mm)
F(mm)
t(mm)
LM0302
3.5± 0.1
3.8± 0.1
2.3± 0.1
8.0± 0.1
12.0± 0.3
5.5± 0.1
0.35± 0.05
10-3. Packaging Quantity
Size
LM0302
Chip / Reel
3000
Inner Box
6000
Carton
24000
Pb
NOTE : Specifications subject to change without notice. Please check our website for latest information.
800.729.2099 tel
www.icecomponents.com
31.10.2013
(01/14) LM0302H-7
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 7
LM0302H Series
SMD Power Choke Coil
SMD Power Choke Coil
10-4. Tearing Off Force
PIC0302H Series
The force for tearing off cover tape is 10 to 130 grams
in the arrow direction under the following conditions.
(referenced ANSI/EIA-481-C-2003 of 4.11 standard)
F
165° to 180°
Top cover tape
Room Temp.
(° C)
Room Humidity
(%)
Room atm
(hPa)
Tearing Speed
(mm/min)
5~35
45~85
860~1060
300
Base tape
Application Notice
1. Storage Conditions :
To maintain the solderabililty of terminal electrodes :
a) Temperature and humidity conditions : Less than 40° C and 60% RH.
b) Recommended products should be used within 12 months from the time of delivery.
c) The packaging material should be kept where no chlorine or sulfur exists in the air.
2. Transportation :
a) Products should be handled with care to avoid damage or contamination from perspiration and skin oils.
b) The use of tweezers or vacuum pick up is strongly recommended for individual components.
c) Bulk handling should ensure that abrasion and mechanical shock are minimized.
Pb
NOTE : Specifications subject to change without notice. Please check our website for latest information.
800.729.2099 tel
www.icecomponents.com
31.10.2013
(01/14) LM0302H-8
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 8