Installation Instructions for CS Series Digital Current Detectors PK 87893 SOLDERING INSTRUCTIONS CLEANING Hand Soldering - Use 60/40 rosin core solder, employing a 399°C (750°F) controlled temperature, 1/8" chisel tip soldering iron. To avoid delamination of the terminals from the ceramic, do not hold the iron on the terminals for more than four seconds. The temperature of the lead at the ceramic conductor interface must not exceed 250°C (482°F). Proper cleaning fluids should be selected based on the type of contaminants to be removed. MICRO SWlTCH recommends alcohols, chlorinated solvents, and florinated solvents. GENERAL INFORMATION Wave Soldering - Use Loncoflux 106A35 or equivalent. Preheaters should be set for 95°C (200°F) on top (component side) of printed circuit board just prior to board entering wave. (This may have to be adjusted depending upon board thickness.) Solder temperature should be a maximum of 260°C (500°F), preferably 252°C to 260°C (485°F to 500°F). Set conveyor speed to approximately 4.5 feet per minute (1,37 meter/min.). Select a speed which gives full solder fillets and minimum of bridging and icicles. The printed circuit board requires rigid support during wave soldering. The CS Series of current detectors have a single digital (TTL logic level, open collector) output that will sink 20mA of output current. This is an open collector output. Normal mounting is with two screws inserted through the mounting holes in the housing. Three 0.20 inch long printed circuit board mounting pins are optional. As is a version adapted for AMP part #102241-1. These sensors will not be damaged by overcurrent in the sensed conductor. OPERATING CHARACTERISTICS Catalog Listing Mtg. Dim. Pinout Fig. Style Operate Current @ 25°C (Amp-Turns) Operate Current -25°C to +85°C (Amp-Turns) Release Output Current Output Current SUPPLY -25°C to +85°C Volt. Volt. (mA) (Amp-Turns Min.) (Volts DC) (Volts) Sinking Response Time Min. Nom. Max. CSDA1BA 1 2 0.32 0.50 0.88 0.50 + 0.5/-0.25 0.08 6 to 16 0.4 20mA 100 CSDA1BC 1 2 2.2 3.5 6.5 2 -- 2.2 3.5 6.5 0.60 0.60 6 to 16 8 to 16 0.4 CSDB1CC 0.4 20mA 100mA 100 3.5 + 4.0/-1.8 3.5 + 4.0/-1.8 100 CSDC1BA 1 2 0.32 0.50 0.88 0.50 + 0.5/-0.25 0.08 5 ± 0.2 0.4 20mA 100 CSDC1BC 1 2 2.2 3.5 6.5 3.5 ± 4.0/-1.8 0.60 5 ± 0.2 0.4 20mA 100 CSDA1AA 1 1 0.32 0.50 0.88 0.50 + 0.5/-0.25 0.08 6 to 16 0.4 20mA 100 CSDA1AC 1 1 2.2 3.5 6.5 3.5 + 4.0/-1.8 0.60 6 to 16 0.4 20mA 100 CSDC1AA 1 1 0.32 0.08 5 ± 0.2 0.4 20mA 100 1 1 2.2 0.88 6.5 0.50 + 0.5/-0.25 CSDC1AC 0.50 3.5 20mA 100 3 0.32 0.60 0.08 0.4 1 5 ± 0.2 0.4 20mA 100 CSDA1DA 1 3 0.32 CSDC1DC 1 3 2.2 3.5 + 4.0/-1.8 0.50 0.88 0.50 + 0.5/-0.25 0.50 0.88 0.50 + 0.5/-0.25 3.5 + 4.0 /-1. 8 3.5 6.5 5 ± 0.2 CSDC1DA 6 to 16 5 ± 0.2 0.4 0.4 20mA 20mA 100 100 CSDA1DC 1 3 2.2 3.5 6 to 16 0.4 20mA 100 6.5 3.5 + 4.0/-1.8 0.08 0.60 0.60 Honeywell Sensing & Control CS Series Digital Current Detectors PK 87893 MOUNTING DIMENSIONS (For reference only) Figure 1 Figure 2 NOTE: Pinout reversed for AMP connector WARRANTY/REMEDY SALES AND SERVICE Seller warrants its products to be free from defects in design, material and workmanship under normal use and service. Seller will repair or replace without charge any such product it finds to be so defective on its return to Seller within 18 months after date of shipment by Seller. The foregoing is in lieu of all other expressed or implied warranties (except of title), including those of merchantability and fitness for a particular purpose. The foregoing is also purchaser's sole remedy and is in lieu of all other guarantees, obligations, or liabilities or any consequential, incidental, or punitive damages attributable to negligence or strict liability, all by way of example. Honeywell serves its customers through a worldwide network of sales offices and distributors. For application assistance, pricing or name of nearest Authorized Distributor, contact a nearby Honeywell sales office. Or, contact: Honeywell Sensing & Control 11 W. Spring St. Freeport, Illinois 61032 Tel. 815/235-6600 While we provide application assistance on MICRO SWITCH products, personally and through our literature, it is up to the customer to determine the suitability of the product in the application. Honeywell Sensing & Control Helping you control your world PK 87893 290 Printed in USA