ZH10 Series Hall-effect Zero Speed Sensors DESCRIPTION The aluminum package is simple to install and adjust. It does The ZH10 Hall-effect Speed Sensor Sensors provide a not require rotational orientation. durable, cost-effective solution in most harsh environments. The sensor is available in a 11,9 mm [15/32 in/0.46875 in] diameter, in a 25,4 mm [1.00 in] length. FEATURES POTENTIAL APPLICATIONS • Low cost • Industrial process control • Omni-directional sensor to target orientation • Factory automation • Digital output • Rotary applications, such as: • Small size – Pumps • Low power consumption – Rollers – Mixers – Fan speed measurement – Transmission – Spindles – Gear reducer RPM – Process speed – Synchronization – Generator set – Compressor speed – Dyno testing ZH10 Series SENSOR SPECIFICATIONS Characteristic Minimum Maximum Unit Supply voltage 4 24 Vdc – Supply current – 6 mA – Output current – 30 mA short circuit protected Output on voltage – 0.6 Vdc Output configuration – – – open drain MOFSET Voltage low – 0.4 V at 30 mA max. sink Voltage high – 30 Vdc Target orientation – – – omnidirectional Duty cycle 35 65 % within operating gap Operating frequency 0 15 k Hz no orientation required Output signal rise/fall time – 4.0 μs 880 Ohm, 20 pF 200 – Vac Dielectric strength Operation gap – <2 mA leakage at gaps below curve (see Air Gap Performance Curve) – – 4.7 5.3 kOhm – -40 [-40] 100 [212] °C [°F] – – 125 [257] °C [°F] – Storage temperature Sealing IP67 – Shock 50 Gs, 11 ms – Vibration 15 Gs, 10 Hz to 2000 Hz – Housing material aluminum – MOUNTING DIMENSIONS (For reference only: mm/[in]) 2 at 25 mA load – Output impedance Operating temperature range Condition www.honeywell.com/sensing Hall Effect Zero Speed Sensor EQUIVALENT ELECTRICAL SCHEMATIC AIR GAP PERFORMANCE CURVE TARGET MOTION Honeywell Sensing and Control 3 ORDER GUIDE Catalog Listing ZH10 Description Hall-effect zero speed sensor WARNING WARNING PERSONAL INJURY MISUSE OF DOCUMENTATION DO NOT USE these products as safety or emergency stop • devices or in any other application where failure of the The information presented in this product sheet is for reference only. Do not use this document as a product product could result in personal injury. installation guide. Failure to comply with these instructions could result in death or serious injury. • Complete installation, operation, and maintenance information is provided in the instructions supplied with each product. Failure to comply with these instructions could result in WARRANTY/REMEDY Honeywell warrants goods of its manufacture as being free of death or serious injury. defective materials and faulty workmanship. Honeywell’s standard product warranty applies unless agreed to otherwise SALES AND SERVICE by Honeywell in writing; please refer to your order Honeywell serves its customers through a worldwide network acknowledgement or consult your local sales office for specific of sales offices, representatives and distributors. For warranty details. If warranted goods are returned to Honeywell application assistance, current specifications, pricing or name during the period of coverage, Honeywell will repair or replace, of the nearest Authorized Distributor, contact your local sales at its option, without charge those items it finds defective. The office or: foregoing is buyer’s sole remedy and is in lieu of all other warranties, expressed or implied, including those of E-mail: [email protected] merchantability and fitness for a particular purpose. In no event shall Honeywell be liable for consequential, special, or indirect damages. Internet: www.honeywell.com/sensing Phone and Fax: While we provide application assistance personally, through Asia Pacific +65 6445-3033 Fax our literature and the Honeywell web site, it is up to the customer to determine the suitability of the product in the +65 6355-2828 Europe +44 (0) 1698 481481 +44 (0) 1698 481676 Fax application. Latin America +1-305-883-8257 Fax Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. +1-305-805-8188 USA/Canada +1-800-537-6945 +1-815-235-6847 +1-815-235-6545 Fax Automation and Control Solutions Sensing and Control Honeywell 1985 Douglas Drive North Minneapolis, MN 55422 www.honeywell.com/sensing 005885-1-EN IL50 GLO Printed in USA June 2007 Copyright © 2007 Honeywell International Inc. All rights reserved.