L-Series B/W Camera EIA CCIR HCM574L HCM584LX HCM384L HCM585LX HCM404LX HCM405LX User Guide Document G-113078-001 – 02/07 – Rev 5 Revisions Issue Date Revisions 1.00 09/06 New document 1.01 09/06 Updated Mains 230V in Figure 2 and Figure 7. 1.02 10/06 Changed 2nd ‘clockwise’ to ‘counterclockwise’ on page 8. 3 10/06 Updated Figure 1, Figure 4, and Figure 5 to show HCM model. 4 11/06 Updated Figure 1 for better quality. 5 02/07 Updated document part no.; added warning to p. iii. Rev 5 ii G-113078-001 02/07 Warnings Installation and servicing should be performed only by qualified and experienced personnel to conform to all local codes and to maintain your warranty. WARNING! 12 VDC/24 VAC models require the use of CSA Certified/UL Listed Class 2 power adapters to ensure compliance with electrical safety standards. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product (applicable in the European Union and other European countries with separate collection systems). This product should be disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures. Explanation of Graphical Symbols THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THE UNIT. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Rev 5 iii THIS SYMBOL INDICATES THAT IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS ACCOMPANY THIS UNIT. G-113078-001 02/07 FCC Compliance Statement Information to the User: This equipment has been tested and found to comply with the limits for a Class A digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Manufacturer’s Declaration of Conformance The manufacturer declares that the equipment supplied with this guide is compliant with the essential protection requirements of the EMC directive 89/336/EEC and the Low Voltage Directive LVD 73/23 EEC, conforming to the requirements of standards EN 55013 for emissions. Rev 5 iv G-113078-001 02/07 Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . 2 Unpack Everything . . . . . . . . . . . . . . . . . . . . . . . . 2 Camera Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Camera Functions . . . . . . . . . . . . . . . . . . . . . . . . . 3 Setting Up Your Camera . . . . . . . . . . . . . . . . . . . . 4 Selecting the Lens . . . . . . . . . . . . . . . . . . . . . . 4 Fixed Lens . . . . . . . . . . . . . . . . . . . . . . . . . 4 Vari-focal Auto Iris Lens . . . . . . . . . . . . . . . 4 Direct Drive (DC) Lens . . . . . . . . . . . . . . . . 4 Video Drive (VSD) Lens . . . . . . . . . . . . . . . 5 Backlight Compensation (BLC). . . . . . . . . . . . 5 Automatic Gain Control (AGC) . . . . . . . . . . . . 5 Synchronization Selection (LL/INT) . . . . . . . . . 5 Line Lock Phase Adjustment Potentiometer . . 6 Lens Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Adjusting the Back Focus . . . . . . . . . . . . . . . . . . . 7 Completing the Installation . . . . . . . . . . . . . . . . . . . 9 Mounting the Camera . . . . . . . . . . . . . . . . . . . . . . 9 Connecting the Camera . . . . . . . . . . . . . . . . . . . 10 Warranty and Service . . . . . . . . . . . . . . . . . . . . . . 11 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Rev 5 G-113078-001 02/07 Introduction The Honeywell L-Series monochrome cameras are ideally suited for use in day-to-day surveillance applications. The L-Series monochrome cameras are designed for exceptional value and performance for everyday use. Their off-the-shelf feature set is designed for high picture quality in standard applications and they require little to no adjustment after installation. Figure 1 Camera Overview C/CS mount adapter: C mount: turn counterclockwise CS mount: turn clockwise Lens connector for Auto Iris lens plug Setscrew: loosen locking ring with a Phillips screwdriver to adjust mounting ring. Back focus adjustment ring Features • • • • • • 1/3” Monochrome CCD C/CS adjustable lens mount adapter Excellent signal-to-noise ratio of more than 50 dB Less than 0.1 lux low light sensitivity for excellent performance in low light conditions Compatible with Video Iris (VSD) or Direct Drive (DC) Auto Iris lens 12 VDC/24 VAC or 230 VAC operation (model dependent) Rev 5 1 G-113078-001 02/07 Before You Begin Please read this guide carefully before you install the L-Series monochrome camera. Keep this guide for future reference. Unpack Everything Check that the items received match those listed on the order form and packing slip. The L-Series packing box should include, in addition to this User Guide: • One L-Series monochrome camera • One Auto Iris lens plug If any parts are missing or damaged, contact the dealer you purchased the camera from or call Honeywell Customer Service (see Contact Information on the back of this manual). Note Rev 5 You will also require a Phillips screwdriver to complete the installation. 2 G-113078-001 02/07 Camera Settings Camera Functions Figure 2 Camera Rear View Low Voltage (HCM574L, HCM384L, HCM584LX, HCM404LX) 5 6 7 6 3 VIDEO CLASS 2 ONLY IRIS LEVEL Mains 230V—Line Voltage (HCM585LX, HCM405LX) IRIS LEVEL 7 3 V-PH VIDEO V-PH PWR PWR 4 VSD VSD AI BLC AGC LL DC AES OFF OFF INT LEGEND 5 2 AI BLC AGC LL AES OFF OFF INT DC 1 1 8 = ON = OFF Shaded box indicates default switch setting. Legend # Description 1 DIP switches for mode settings (see Figure 3) 2 Auto Iris Lens select switch, VSD for Video or DC for Direct Drive 3 Video output connector 4 Power input connector (24 VAC: 3 terminals)—Low Voltage model only 5 Power LED indicator 6 DC Iris level adjustment, for use with DC Iris lens 7 V-Phase adjustment, for use with Line lock 8 Mains 230V Line Voltage power connector Rev 5 3 G-113078-001 02/07 Setting Up Your Camera Figure 3 shows the factory set DIP switch settings. Automatic Gain Control (AGC) is set ON. Figure 3 Factory Set DIP Switch Settings IRIS LEVEL Low Voltage version shown CLASS 2 ONLY IRIS LEVEL VIDEO V-PH PWR AES OFF OFF INT VSD AI BLC AGC LL DC AES OFF OFF INT AI BLC AGC LL LEGEND = ON VSD DC = OFF Selecting the Lens Fixed Lens Set the AES/AI switch on the rear of the camera (see Figure 3) to AES. Vari-focal Auto Iris Lens Vari-focal Auto Iris lenses (Direct Drive [DC] or Video Drive [VSD]) are connected to the camera via a 4-pin square socket located at the side of the camera. Set the AES/AI DIP switch to AI. To set a different exposure, see Backlight Compensation (BLC) on page 5. Direct Drive (DC) Lens 1. 2. Set the VSD/DC switch on the rear of the camera to DC. Set the AES/AI DIP switch to AI. Slowly turn the IRIS LEVEL potentiometer until the picture on the monitor is as clear as possible and is not too bright. Rev 5 4 G-113078-001 02/07 Video Drive (VSD) Lens Set the VSD/DC switch on the rear of the camera (see Figure 3) to VSD. Backlight Compensation (BLC) If there is excessive light (for example, a window exists in a scene), the camera tries to compensate by reducing the overall exposure, resulting in the areas surrounding the window becoming too dark. Turn the BLC switch ON to eliminate the silhouette effect. Automatic Gain Control (AGC) This feature can improve picture quality when the level of scene illumination is low. When set to OFF, the maximum gain is 11 dB. When set to ON, the maximum gain is 30 dB. Synchronization Selection (LL/INT) This switch selects the synchronization mode of the camera. When the camera is connected to an AC supply, the Line lock (LL) mode is used to lock the camera’s frame rate to the frequency so that each camera in the system is triggered at the same point on the supply’s AC cycle. The default setting is LL. WARNING! The LL/INT switch must be set to INT when operating from 12 VDC. Rev 5 5 G-113078-001 02/07 V-PH Low Voltage version shown CLASS 2 ONLY IR IS LEVEL VID EO V-PH PWR AES OFF OFF IN T VSD AI BLC AGC LL DC INT L EG E ND LL = ON = OFF Line Lock Phase Adjustment Potentiometer When the camera is in Line lock mode, it is possible to adjust the point on the AC cycle at which the camera triggers. This feature allows for synchronization of cameras that are connected to different phases. The V-PHASE adjustment potentiometer allows the line lock phase trigger point to be adjusted by 270°. Rotating the potentiometer clockwise advances the trigger point and turning it counterclockwise retards the trigger point. If all cameras in a system are on the same phase then no line lock phase adjustment should be made. Rev 5 6 G-113078-001 02/07 Lens Installation Adjusting the Back Focus The back focus adjustment is accessible at the front end of the camera housing to adjust the back focal length or picture focus. The range of adjustment allows both C- and CS-mount lenses to be used without the need for a spacer ring. Figure 4 C C/CS Mount CS Setscrew 1. 2. 3. Loosen the setscrew with a Phillips screwdriver. Adjust the focus ring to focus the picture. Retighten the setscrew. Rev 5 7 G-113078-001 02/07 Figure 5 DC and VSD Lens Pin Definition 4-pin Auto Iris lens connector 2 1 4 3 1 3 2 4 Pin DC (Direct Drive) lens Video (VSD) lens 1 CTRL - Power (+12V) 2 CTRL + NC 3 DRV + Video Signal 4 DRV - GND Set the select switch to DC. Set the select switch to VSD. Rev 5 8 G-113078-001 02/07 Completing the Installation Mounting the Camera Mounting points are provided on the top of the camera for mounting the camera on a bracket or tripod. They are designed to accept standard sized 1/4 x 20 mounting screws. This bracket can be unscrewed and mounted onto the opposite side of the camera, depending on your application. The mounting bracket must be capable of supporting the weight of the camera and its lens. Note Some installation codes dictate that the mounting bracket must be capable of supporting up to four times the combined weight of the camera and lens. Figure 6 Camera Mount Unscrew 3 bracket securing screws and then resecure the bracket on the other side of the camera. Rev 5 9 G-113078-001 02/07 Connecting the Camera 1. 2. Connect the VIDEO connector on the rear of the camera to the video-in connector on your monitor. Connect the camera to a power supply appropriate for your installation. HCM574L, HCM384L, HCM584LX, HCM404LX: 12 VDC or 24 VAC power supply HCM585LX, HCM405LX: 230V power supply 3. Plug in the power supply. The power (PWR) LED illuminates to show that the camera is receiving power. If it does not illuminate, check the connections and the power source. Figure 7 Camera Connections Low Voltage (HCM574L, HCM384L, HCM584LX, HCM404LX) Mains 230V—Line Voltage (HCM585LX, HCM405LX) Connect to Monitor CLASS 2 ONLY IRIS LEVEL IRIS LEVEL VIDEO V-PH VIDEO V-PH PWR PWR VSD AES OFF OFF INT VSD AI BLC AGC LL DC AES OFF OFF INT AI BLC AGC LL DC Power LED Rev 5 10 G-113078-001 02/07 Warranty and Service Subject to the terms and conditions listed on the Product warranty, during the warranty period Honeywell will repair or replace, at its sole option, free of charge, any defective product returned prepaid. In the event you have a problem with any Honeywell product, please call Customer Service at 1.800.796.CCTV (North America only) for assistance or to request a Return Merchandise Authorization (RMA) number. For Europe and the United Kingdom, please contact your Honeywell dealer. Be sure to have the model number, serial number, and the nature of the problem available for the technical service representative. Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped to Honeywell without a clearly identified Return Merchandise Authorization (RMA) number may be refused. Specifications Note These specifications refer to all models, except where otherwise noted. HCM574L Operational Image Sensor: Video Standard: Scanning System: Number of Pixels (H x V): Minimum Illumination: Horizontal Resolution: Video Output: Rev 5 HCM584LX HCM585LX 1/3” Super HAD CCD (B/W) EIA CCIR 525 lines, 2:1 interlace 768 x 494 625 lines, 2:1 interlace 752 x 582 > 0.07 lux @ F1.2 (50 IRE, AGC ON) 570 TVL 580 TVL 1 Vp-p @ 75 Ohms 11 G-113078-001 02/07 HCM574L HCM584LX Sync System: HCM585LX Internal/Line lock S/N Ratio: > 50 dB Auto Gain Control (AGC): On/Off ALC: EE/VSD/DC Automatic Electronic Shutter (AES): 1/60 1/100,000 sec Lens Mount: 1/50 - 1/100,000 sec C/CS mount (adjustable) BLC: On/Off Gamma: Electrical Input Voltage: Input Voltage Range: Power Consumption: Mechanical Dimension: (W x H x D) Weight: 0.45 12 VDC/24 VAC 230 VAC 11 - 16 VDC, 17 - 28 VAC 2 W (max) 230 VAC ± 10% 2 W (max) 3.2 W (max) 2.68 x 2.2 x 4.72 in. (68 x 56 x 120 mm) 2.68 x 2.2 x 5.51 in. (68 x 56 x 140 mm) 0.77 lb (.350 kg) Environmental Temperature: 0.84 lb (.380 kg) Operating: 14°F to 122°F (-10°C to +50°C) Storage: -4°F to158°F (-20°C to +70°C) Regulatory Emissions: Immunity: Safety: Note FCC, CE (EN55013) CE (EN50130-4) EU: 73/23/EEC LVD These specifications refer to all models, except where otherwise noted. HCM384L Operational Image Sensor: Video Standard: Rev 5 HCM404LX HCM405LX 1/3” Super HAD CCD (B/W) EIA CCIR 12 G-113078-001 02/07 HCM384L Scanning System: Number of Pixels (H x V): Minimum Illumination: Horizontal Resolution: 525 lines, 2:1 interlace HCM404LX HCM405LX 625 lines, 2:1 interlace 510 x 492 500 x 582 < 0.05 lux @ F1.2 (50 IRE, AGC ON) 380 TVL 400 TVL Video Output: 1 Vp-p @ 75 Ohms Sync System: Internal/Line lock S/N Ratio: > 50 dB Auto Gain Control (AGC): On/Off ALC: Automatic Electronic Shutter (AES): EE/VSD/DC 1/60 1/100,000 sec Lens Mount: C/CS mount (adjustable) BLC: On/Off Gamma: Electrical Input Voltage: Input Voltage Range: Power Consumption: Mechanical Dimension: (W x H x D) Weight: Environmental Temperature: 1/50 - 1/100,000 sec 0.45 12 VDC/24 VAC 11 - 16 VDC, 17 - 28 VAC 2 W (max) 2 W (max) 2.68 x 2.2 x 4.72 in. (68 x 56 x 120 mm) 0.77 lb (.350 kg) 230 VAC 230 VAC ± 10% 3.2 W (max) 2.68 x 2.2 x 5.51 in. (68 x 56 x 140 mm) 0.84 lb (.380 kg) Operating: 14°F to 122°F (-10°C to +50°C) Storage: -4°F to158°F (-20°C to +70°C) Regulatory Emissions: Immunity: Safety: Rev 5 FCC, CE (EN55013) CE (EN50130-4) EU: 73/23/EEC LVD 13 G-113078-001 02/07 Honeywell Video Systems (Head office) 2700 Blankenbaker Pkwy, Suite 150 Louisville, KY 40299, USA www.honeywellvideo.com ℡ +1.800.796.2288 Honeywell Security Australia Pty Ltd. Unit 5, Riverside Centre 24-28 River Road West Parramatta, NSW 2150, Australia www.ademco.com.au ℡ +61.2.8837.9300 Honeywell Security Asia Pacific 33/F Tower A, City Center, 100 Zun Yi Road Shanghai 200051, China www.security.honeywell.com/cn ℡ +86 21.2527.4568 Honeywell Video Systems Northern Europe Netwerk 121 1446 WV Purmerend, The Netherlands www.SecurityHouse.nl ℡ +31.299.410.200 Honeywell Video Systems UK Ltd. Aston Fields Road, Whitehouse Ind Est Runcorn, Cheshire, WA7 3DL, UK www.honeywellvideo.com ℡ +0844 8000 235 Honeywell Security South Africa Unit 6 Galaxy Park, 17 Galaxy Avenue Linbro Park, P.O. Box 59904 2100 Kengray, Johannesburg South Africa www.honeywell.co.za ℡ +27.11.574.2500 Honeywell Security Asia Flat A, 16/F, CDW Building 388 Castle Peak Road Tsuen Wan, N.T., Hong Kong www.security.honeywell.com/hk ℡ +852.2405.2323 Honeywell Security Deutschland Johannes-Mauthe-Straße 14 D-72458 Albstadt, Germany www.honeywell.com/security/de ℡ +49.74 31.8 01.0 Honeywell Security France Parc Gutenberg, 8, Voie La Cardon 91120, Palaiseau, France www.honeywell.com/security/fr ℡ +33.01.64.53.80.40 Honeywell Security Poland Chmielewskiego 22a, 70-028 Szczecin, Polska www.ultrak.pl ℡ +48.91.485.40.60 Honeywell Security Italia SpA Via Treviso 2 / 4 31020 San Vendemiano Treviso, Italy www.honeywell.com/security/it ℡ +39.04.38.36.51 Honeywell Security Czech Republic Havránkova 33, Brno Dolní Heršpice, 619 00 Czech Republic www.olympo.cz ℡ +420.543.558.111 Honeywell Security España Mijancas 1. 3a Planta P.Ind. Las Mercedes 28022 Madrid, Spain www.honeywell.com/security/es ℡ +34.902.667.800 Honeywell Security Slovakia Republic Vajnorská 142, 83104 Bratislava Slovakia www.olympo.sk ℡ +421.2.444.54.660 www.honeywellvideo.com +1.800.796.CCTV (North America only) [email protected] Document G-113078-001 02/07 Rev 5 © 2007 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.