COMPOSITION: You must be fully aware of all the distinctive features and precautions related to this camera before installing it. DIMENSIONS(mm): 100.0 Mounting Screw 130.6 INSTALLATION: 6 Put the dome cover over the base. 7 Fix the dome cover on the base by covering. Mounting Screw Dome Cover Weight Insert coin to the side hole and remove the dome cover by twist coin. PRECAUTIONS: ! Need Help? Call 1.800.796.CCTV for sales, service and customer support. www.honeywellvideo.com Fixed Lens & IR LED Type Do not install or use the camera in an environment where the humidity is high. b 2 H /A EAT UD ER IO There are no user-serviceable parts inside it. Note When this camera is installed near wireless communication devices that emits strong electromagnetic field, irregularity such as noise on the monitor may appear. CONNECTION: J504 1 Tilt rotation: Adjusting the vertical angle. 2 Pan rotation: Adjusting the horizontal angle. 3 Horizontal rotation: Adjusting the horizontal position of the screen. 4 IR LED: 850nm / 30°(24EA) 5 Sensor Camera Lay-out a AC24V a Function Selection Switch: •FL(Flickerless) ON/OFF •AGC(Auto Gain Control) ON/OFF •BLC(Back Light Compensation) ON/OFF b Service Monitor Connecter: Use service monitor connector to set camera angle & focus when installing. CAUTION : When AGC is off, D/N does not work because the D/N switching function is dependent on the AGC level. TROUBLESHOOTING: If you have trouble operating your camera, refer to the following. If the guidelines do not enable you to solve the problem, contact an authorized technician. • Power Consumption: 5W • IR LED Specification: 850nm / 30°(24EA) IR LED (4mm Fixed Lens) • The wire is polarized. • Use 12VDC #1 Connecting to Monitor and Power 12VDC Power Type AC 24V J503 BLC ON AGC OFF FL ON Do not drop the camera or subject them to physical shocks. It can cause malfunctions to occur. ! 05 Do not disassemble the camera. 360º 3 1 360º Fixed Lens & IR LED Type J5 ! READ AND KEEP THIS OPERATION MANUAL ta CAMERA SET-UP: It can cause the image quality to be poor. ! le to ins J502 ! 4 mp Built-in 3-axis camera bracket makes it much easier to rotate in any direction. 5 Do use the camera under conditions where temperatures are within -10°C to 45°C. Be especially careful with ventilation under high temperatures. Si 90º Design and specifications are subject to change without notice. NAME AND FUNCTION: Do not install the camera in extreme temperature conditions. • 1/3" Sony Super HAD CCD • 380 TV Lines Resolution • 4mm Fixed Lens • Color Day/Night with 24 LEDs • Auto White Balance • AGC, BLC, Flickerless On/Off • Extra Video Output for Installer • 3-Axis Camera Construction • Diameter of Bubble : 100mm ll N OT E 2 : 1 Interlace 15.734kHz 15.625kHz 59.94Hz 50Hz 1/3" SONY Super HAD CCD 270K / 250K 320K / 290K More than 48dB (AGC Off) 380 TV Lines 1.0 Vp-p (75 Ohms, composite) Fixed Lens : f=4.0mm, 81º Manual Internal 0 Lux, IR LED 1/60 ~ 100,000 Sec. 1 /50 ~ 100,000 Sec. Auto On / Off On / Off (with Slide Switch) On / Off (with Slide Switch) Power, Video 12VDC (10.8V~15V), 0.4A / 5W (Max) 100mm Approx. 366g J501 Adjust desired focus and scene by turning and moving the 3-axis camera bracket by hand. PAL PAL : 625 Lines VIDEO 5 Dome Base NTSC NTSC : 525 Lines SWITCH Fixed the camera to a celling using four screws. Signal System Scanning System Scanning Frequency (H) Scanning Frequency (V) Image Sensor Total / Effective Pixels No. S / N Ratio Resolution Video Output Level Lens Focus Sync. System Sensitivity Electronic Shutter White Balance AGC BLC Flickerless Input / Output Connector Power Consumption Dome Size (Ø) 1 2 3 4 Model DC LEVEL 3 Draw out power / video wires to the connecting places. Guide Pattern ON 2 Drill four holes according to the guide pattern then insert anchors into the drilled holes. Operation Manual SPECIFICATIONS: • Stick the guide pattern on the wall or ceiling. Ceiling P/N:3810-0072H Rev 0 03/18 1 HD60 Series 13.7 Operation Manual 37.3 75.7 Service Monitor Cable 102.0 51.0 Guide Pattern Video (Yellow) No. GND #2 Power - 12VDC (Red) power source. Video Output Function Terminal Color Remark #1 Video Output Yellow 1.0 Vp-p #2 Power Input Red 12VDC(10.8V~15V), 0.4A/5W(Max) The image does not appear on the screen. Check the power source for the monitor and camera and ensure that the voltage and polarity are properly connected and being supplied correctly. The image on the screen is dim. Check if the lens is stained. If dirty, clean the lens with a soft, clean cloth. Adjust the Back Focus of the lens again. The camera does not work properly, the surface of the camera case is hot, and a black line appears on the screen. Check if you have connected the camera to a proper power source and If there is no problem with the power, turn the unit off immediately and seek assistance from our Customer Service department. The screen blinks a lot. Check if the camera is pointed toward the sun or a fluorescent lamp. Adjust the angle or location of the camera if too much light is coming into the screen.