P/N:3810-0071G Rev 0 03/18 USER INFORMATION: Design and specifications are subject to change without notice. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE SPECIFICATIONS: The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance. THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM OF THE SYSTEM. "WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE" PRECAUTION: ! All the warnings and instructions of this manual should be followed. Remove the plug from the outlet before cleaning. Do not use liquid aerosol detergents. Use water damped cloth for cleaning. To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. Do not place anything on top of the unit that might spill or fall into it. Do not attempt to service this unit yourself as opening or removing covers may you to dangerous voltage or other hazards. Please refer all servicing to qualified service personnel. Keep enough space around the unit for ventilation. Slots and openings on the monitor should not be blocked. During flashes of lightning or cracks of thunder, or when the system is not used for a long time, unplug the system power supply to protect the unit from lightening or power surges. HD40 Series NTSC : 525 Lines PAL : 625 Lines 2 : 1 Interlace 15.734kHz 15.625kHz 59.94Hz 50Hz 1/3 inch SONY Super HAD CCD 270K/250K 320K/290K More than 48dB 380 TV Lines 1.0 Vp-p (75 Ohms, composite) Fixed Lens (f=3.8mm) Manual Internal 0.1 Lux 1/60~100,000 Sec. 1/50~100,000 Sec. Auto Auto Power (Red Jack), Video (Yellow Jack) 12VDC (10V~15V), 0.15A / 1.8W (Max) 85mm Approx. 210g Operation Manual • 1/3” SONY Super HAD CCD • 380 TV Lines Resolution • Built-in Fixed Lens (f=3.8mm) • Min. Illumination : 0.1 Lux • Auto White Balance • Diameter of Bubble : 85mm • Easy Install (3-Axis) Si mp le to ins t READ AND KEEP THIS OPERATION MANUAL a ll Signal System Scanning System Scanning Frequency (H) Scanning Frequency (V) Image Sensor Total/Effective Pixels No. S/N Ratio Resolution Video Output Level Lens- Mirror Cover Focus Sync. System Sensitivity Electronic Shutter White Balance AGC Input/Output Connector Power Consumption Dome Size (Ø) Weight • COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Explanation of two Symbols Need Help? Call 1.800.796.CCTV for sales, service and customer support. www.honeywellvideo.com 90º COMPOSITION: INSTALLATION: This manual explains the installation and operating method for the color dome camera. Before installation, make sure you are familiar with this product's special features and proper operating technique. Drill two holes according to the guide pattern then insert anchors into the drilled holes. 3 Draw out power/video wires to the connecting places. 4 Fixed the camera to a celling using two screws. 5 Adjust desired focus and scene by turning and moving the 3-axis camera bracket by hand. 6 Put the dome cover over the base. 7 Fix the dome cover on the base by covering. Ceiling Mounting Screw TROUBLESHOOTING: Operation Manual Guide Pattern CONNECTION: Dome Base • The wire is polarized. • Use 12VDC power source. 12VDC Power Type #1 Video (Yellow) Mounting Screw #2 No. Function Terminal Color GND #1 Video Output Yellow 1.0 Vp-p #2 Power Input Red 12VDC(10V~15V), 1.8W(Max) Power - 12VDC (Red) Remark DIMENSIONS: Dome Cover 4.45” (113 mm) NOTE Insert coin to the side hole and remove the dome cover by twist coin. Video Output 1.34” (34 mm) 2 Guide Pattern 8” 0.1 ) 2- 5 mm (4. 1.68” (42.7 mm) Stick the guide pattern on the wall or ceiling. 3.02” (76.7 mm) 1 Dome Camera 3.35” (85 mm) Built-in 3-axis camera bracket makes it much easier to rotate in any direction. 3.35” (85 mm) Tilt 360º Horizontal 360º Pan If you have trouble operating your camera, refer to the following. If the guidelines do not enable you to solve the problem, contact an authorized technician. The image does not appear on the screen. Check the power source for the monitor and camera and ensure that the voltage and polarity are properly connected and being supplied correctly. The image on the screen is dim. Check if the lens is stained. If dirty, clean the lens with a soft, clean cloth. Adjust the Back Focus of the lens again. The camera does not work properly, the surface of the camera case is hot, and a black line appears on the screen. Check if you have connected the camera to a proper power source and If there is no problem with the power, turn the unit off immediately and seek assistance from our Customer Service department. The screen blinks a lot. Check if the camera is pointed toward the sun or a fluorescent lamp. Adjust the angle or location of the camera if too much light is coming into the screen.