6009 SERIES 7/8 In. Dia. Servo Mount PRECISION POSITION SENSORS STANDARD PRODUCT OFFERING MS PART NUMBER RESISTANCE 6009-1000-030 6009-1002-030 6009-1003-030 30° 1KΩ ±10% 5KΩ ±10% 10KΩ ±10% .062 ±.005 .062 ±.005 .062 ±.005 30° .255 .010 .1249 .1245 2 3 1 .63 MAX. .875 .005 .781 MAX. .7500 .7490 .500 .032 STANDARD MODEL ELECTRICAL CHARACTERISTICS RESISTANCE: ACTIVE ELECTRICAL ANGLE: ELECTRICAL CONTINUITY ANGLE: INDEPENDENT LINEARITY: END VOLTAGE: VOLTAGE RESOLUTION: OUTPUT SMOOTHNESS: RESISTANCE TEMP. COEFFICIENT: POWER RATING @ 70°C: WIPER CONTACT CURRENT: DIELECTRIC STRENGTH: INSULATION RESISTANCE: 1kΩ to 10kΩ ±10% 340° 344° MIN. ±0.5% 0.5% MAX. VIRTUALLY INFINITE 0.1% MAX. 400PPM/°C MAX. 1.0 WATT MAX. 10 MilliAmps MAX. 750 VRMS @ 60Hz 100 MegΩ MIN. @ 500VDC .625 MAX. STANDARD ENVIRONMENTAL CHARACTERISTICS OPERATING TEMP. RANGE: ROTATIONAL OPERATING LIFE: SCHEMATIC DIAGRAM 2 STANDARD MODEL MECHANICAL CHARACTERISTICS MECHANICAL ROTATION: STARTING TORQUE: RUNNING TORQUE: TOTAL WEIGHT (1-GANG): PILOT RUNOUT: SHAFT RUNOUT: SHAFT END PLAY: SHAFT RADIAL PLAY: LATERAL RUNOUT: -65°C To +125°C 100 x 106 REVOLUTIONS MIN. CW CONTINUOUS 0.25 Oz.-In. MAX. 0.20 Oz.-In. MAX. 0.6 Oz. MAX. 0.001 In. TIR 0.001 In. TIR 0.003 MAX. 0.001 In. TIR 0.002 In. TIR 3 1 VIEWED FROM SHAFT END ALL OTHER GENERAL REQUIREMENTS IN ACCORDANCE WITH MIL-PRF-39023 STANDARD MATERIALS OF CONSTRUCTION HOUSING AND COVER: SHAFT AND BALL BEARINGS: RESISTANCE ELEMENT: ELECTRICAL CONTACTS: SOLDER TERMINALS: ANODIZED ALUMINUM STAINLESS STEEL CO-MOLDED CONDUCTIVE PLASTIC MULTI-FINGER PRECIOUS METAL GOLD PLATED BRASS Position Sensor Products precisionsensors.meas-spec.com 424 Crown Point Circle, Grass Valley, CA 95945 Ph: 530.273.4608 Fax: 530.273.0769 8-7-13 www.meas-spec.com 6009 SERIES 7/8 In. Dia. Servo Mount PRECISION POSITION SENSORS ANODIZED ALUMINUM HOUSING TURRET-STYLE SOLDER TERMINALS STAINLESS STEEL PRECISION SHAFT SHAFT INSULATOR CO-MOLDED RESISTANCE ELEMENT ANODIZED ALUMINUM COVER STAINLESS STEEL PRECISION BALL BEARINGS WELDED MULTI-FINGER PRECIOUS METAL CONTACTS STANDARD ELECTRICAL CHARACTERISTICS RESISTANCES (±10%): ACTIVE ELECTRICAL ANGLE: ELECTRICAL CONTINUITY ANGLE: INDEPENDENT LINEARITY: END VOLTAGE: VOLTAGE RESOLUTION: OUTPUT SMOOTHNESS: RESISTANCE TEMP. COEFFICIENT: POWER RATING @ 70°C: WIPER CONTACT CURRENT: DIELECTRIC STRENGTH: INSULATION RESISTANCE: AVAILABLE OPTIONS 1KΩ, 5KΩ, and 10kΩ 340° 344° MIN. ±0.5% 0.5% MAX. VIRTUALLY INFINITE 0.1% MAX. 400PPM/°C MAX. 1.0 WATT MAX. 10 MilliAmps MAX. 750 VRMS @ 60Hz 100 MegΩ MIN. @ 500 VDC STANDARD MECHANICAL CHARACTERISTICS MECHANICAL ROTATION: STARTING TORQUE: RUNNING TORQUE: TOTAL WEIGHT (1-GANG): PILOT RUNOUT: SHAFT RUNOUT: SHAFT END PLAY: SHAFT RADIAL PLAY: LATERAL RUNOUT: SPECIAL ELECTRICAL ANGLES UP TO 355° MAX. SPECIAL SHAFT LENGTHS AND FEATURES SUCH AS REAR EXTENSIONS, FLATS, SLOTS, AND STEPS. ANODIZED ALUMINUM STAINLESS STEEL CO-MOLDED CONDUCTIVE PLASTIC MULTI-FINGER PRECIOUS METAL GOLD PLATED BRASS Position Sensor Products precisionsensors.meas-spec.com CURRENT LIMIT RESISTORS AND OTHER INTERNAL CIRCUIT COMPONENTS (CAPS, DIODES, ETC.) MULTI-GANG CONSTRUCTION (UP TO 6) ON A COMMON SHAFT OR CONCENTRIC SHAFTING (ADD .320 LENGTH PER GANG). -65°C To +125°C 100 x 10 6 REVOLUTIONS MIN. ALL OTHER GENERAL REQUIREMENTS IN ACCORDANCE WITH MIL-PRF-39023 ADDITIONAL TAPS, CURRENT OR VOLTAGE SPECIAL TRANSFER FUNCTIONS: NON-LINEAR OUTPUTS LOAD COMPENSATION TRIG, LOG, AND EXPONENTIAL OUTPUTS STANDARD MATERIALS OF CONSTRUCTION HOUSING AND COVER: SHAFT AND BALL BEARINGS: RESISTANCE ELEMENT: ELECTRICAL CONTACTS: SOLDER TERMINALS: SPECIAL LINEARITIES AS LOW AS 0.15%, ABSOLUTE (INDEXED) OR INDEPENDENT OVER SPECIFIED REGIONS. WIRE LEADS OR CABLE IN PLACE OF TERMINALS CONTINUOUS 0.25 Oz.-In. MAX. 0.20 Oz.-In. MAX. 0.6 Oz. MAX. 0.001 In. TIR 0.001 In. TIR 0.003 MAX. 0.001 In. TIR 0.002 In. TIR STANDARD ENVIRONMENTAL CHARACTERISTICS OPERATING TEMP. RANGE: ROTATIONAL OPERATING LIFE: CUSTOM RESISTANCE VALUES (500Ω TO 50kΩ) AND TOLERANCES AS LOW AS ±5% SPECIAL TORQUE OR DETENT REQUIREMENTS AS LOW AS .015 STARTING TORQUE. SPECIAL MOUNTING DIMENSIONS OR FEATURES INCLUDING ANTI-ROTATION PINS, BOLT FLANGES, AND THREADED HOLES. ROTATIONAL STOPS LIMITING SHAFT TRAVEL. ANCILLIARY DEVICES SUCH AS SPRING RETURNS, CLUTCHES, BRAKES, AND SWITCHES. SPECIAL ENVIRONMENTAL CAPABILITES SUCH AS MOISTURE SEALS, HIGH SHOCK AND VIBRATION. 424 Crown Point Circle, Grass Valley, CA 95945 Ph: 530.273.4608 Fax: 530.273.0769 8-7-13 www.meas-spec.com