RS3A THRU RS3M Surface Mount Fast Recovery Rectifiers Features ● Low profile package ● Ideal for automated placement ● Glass passivated chip junctions ● Fast switching for high efficiency ● High forward surge capability ● High temperature soldering： 260℃/10 seconds at terminals ● Component in accordance to RoHS 2002/95/1 and WEEE 2002/96/EC Major Ratings and Characteristics Mechanical Date ● Case: JEDEC DO-214AA molded plastic body over glass passivated chip ● IF(AV) 3.0 A VRRM 50 V to 1000 V IFSM 100 A trr 150nS, 250nS, 500nS VF 1.3 V Tj max. 150 °C Terminals: Solder plated, solderable per J-STD-002B and JESD22-B102D ● Polarity: Laser band denotes cathode end Maximum Ratings & Thermal Characteristics (TA = 25 °C unless otherwise noted) Items Symbol RS3A RS3B RS3D RS3G RS3J RS3K RS3M UNIT Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 1000 V Maximum RMS voltage VRMS 35 70 140 280 420 560 700 V Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 V Maximum average forward rectified current IF(AV) 3.0 A Peak forward surge current 8.3 ms single half sine-wave superimposed on rated load IFSM 100 A Thermal resistance from junction to lead(1) RθJL 25 ℃/ W TJ ,TSTG –55 to +150 ℃ Operating junction and storage temperature range Note 1: Mounted on P.C.B. with 0.28x 0.28” (7.0 x 7.0mm) copper pad areas. Electrical Characteristics Items Instantaneous forward voltage Reverse current Reverse recovery time Typical junction capacitance (TA = 25 °C unless otherwise noted) Test conditions IF=3.0 A VR=VDC TA=25℃ TA=100℃ Symbol RS3A~RS3G VF trr 4.0 V ,1MHz CJ RS3J RS3K~RS3M 1.3 μA 50 150 250 30 UNIT V 5 IR IF = 0.5 A , IR = 1.0 A , Irr = 0.25 A Note 2: Pulse test:300μs pulse width,1% duty cycle. http://www.trr-jx.com (2) 500 nS pF RS3A THRU RS3M Surface Mount Fast Recovery Rectifiers Characteristic Curves (TA=25 ℃ unless otherwise noted) http://www.trr-jx.com RS3A THRU RS3M Surface Mount Fast Recovery Rectifiers Package Outline Notice ● Product is intended for use in general electronics applications. ● Product should be worked less than the ratings; if exceeded, may cause permanent damage. or introduce latent failure ● The absolute maximum ratings are rated values and must not be exceeded during operation. The following are the general mechanisms. derating methods you design a circuit with a device. IF(AV) : We recommend that the worst case current be no greater than 80% . IFSM : This rating specifies the non-repetitive peak current. This is only applied for an abnormal operation, which the general during the lifespan of the device. TJ : Derate this rating when using a device in order to ensure high reliability. We recommend that the device be used at a TJ of below 125°C. ● TRR is registered trademark of Rising-sun Technology. Rising-sun Technology reserves the right to make changes to any product in this specification to improve reliability,functional characteristics,or design without notice. ● Rising-sun Technology does not assure any liability arising out of the applications or any product described in this specification. ● Rising-sun Technology advises customers to obtain the latest version of the device information before placing orders to verify that the required information is current. http://www.trr-jx.com