H HiTRON UNIVERSAL INPUT HARMONIC CORRECTION (PFC) AC-DC N+1 REDUNDANCY AND LOAD SHARING INTERNAL FRONT-END SWITCHING POWER SUPPLIES 2000 WATTS SINGLE OUTPUT WITH STANDBY HTCA2000R SERIES FEATURES: 1U HEIGHT FRONT-END POWER SUPPLY BUILT-IN 5V/1A STANDBY POWER WIDE OPERATING TEMPERATURE RANGE OF -40°C TO +70 °C INTERNAL OR-ING DIODES FOR N+1 REDUNDANCY HOT-SWAPPABLE HIGH EFFICIENCY & DENSITY I2C/TxRx INTERFACE STATUS & CONTROL PROGRAMMMABLE OUTPUT VOLTAGE & CURRENT LIMITED CE LEVEL IV COMPLIANT SPECIFICATION INPUT SPECIFICATION OUTPUT SPECIFICATION Input Voltage: Typ. 90-264Vac. Power Factor: Meet Harmonic Correction IEC 61000-3-2. Power Factor typ. 0.99. Input Connector: Positronic 47-pin PCIH47M400A1. Input Frequency: 47-63Hz. Inrush Current: 18A(rms) at 230Vac; 39A (peak) at 230Vac. Input Current: 13.5A at 115Vac / 9.5A at 230Vac. Dielectric Withstand: Meet IEC 60950-1 regulation. EMI: Meet EN 55022 FCC Class B. Hold-up Time: Typ. 15mS at 115Vac. Typ. 8mS at 230Vac. Remote ON/OFF: Available. Power Fail Signal: Available. Status LED: See Front panel LED status & monitoring signal. Over Temperature Protection (OTP): Installed NTC and thermostat. Leakage Current: Typ. 0.9mA at 230Vac. No-Load Power: Typ.20Watt at 115Vac. Typ.18Watt at 230Vac. Output Voltage: See Ratings Chart. Output Current: See Ratings Chart. Output Power: Total continuous 1400W at 90-180Vac. Total continuous 2000W at 180-264Vac. Output Connector: Positronic 47-pin PCIH47M400A1. Line Regulation: VO1 typ. 0.5%, VO2 typ. 0.5%. Load Regulation: VO1 typ. 1.0%, VO2 typ. 3%. Total Regulation: VO1 typ. 2.0%, VO2 typ. 5.0%. Noise & Ripple: Typ. 1% peak-peak. OVP: Built-in at all outputs. Adjustability: Available for VO1. Hot-Swap: Available. N+1 Redundancy: Installed with internal OR-ing diodes at all outputs and third-wire current sharing method for N+1 redundancy operation. Current Sharing: Available for VO1. DC OK Signal: Available for VO1. Power OK Signal: Available for VO1. Over Current Protection (OCP): Installed at each rail. Overload Protection (OLP): Fully protected against output overload or short circuit. Programmable output current limited. GENERAL SPECIFICATION Efficiency: Typ. 91% at 115Vac, 93% at 230Vac. Switching Frequency: 70KHz for PFC, 120KHz for PWM. Circuit Topology: Interleaved PFC & ZVS Full-bridge circuit. Transient Response: Peak transient less than 520mV and recover within 2ms at 25% load-change. Safety Standard: IEC 60950-1 Class I. Construction: 348 x 101.6 x40.2mm/13.7 x 4 x 1.58inch. Operating Temperature: -40°C to +70 °C derate linearly from 100% power at +50 °C to 60% power at +70 °C. (Please refer to the derating chart) Storage Temperature: -40°C to +85 °C. Cooling: Built-in dual internal DC ball bearing fans with smart fan speed control. Power Density: Typ. 15.7 Watts/ cubic inch at 90-180Vac. Typ. 22.4 Watts/ cubic inch at 180-264Vac. NOTE: (1)All measurement are at nominal input, full load and +26°C unless otherwise specifications. (2)Due to requests in market and advances in technology, specifications subject to change without notification. (3)A warm-up time 3 minutes is required after cold start at temperature from -40 °C to +0°C. Hitron Electronics Cororation. B4-11, P.O. Box 26-110 Kaohsiung Export Processing Zone Kaohsiung 806 Taiwan TEL: 886-7-8210410/FAX: 886-7-8419917, 886-7-8210511/E-mail: [email protected] /Web-site: www.hitron-e.com 1 Sep. 11 2013 OUTPUT VOLTAGE / CURRENT RATINGS CHART SINGLE OUTPUT w/Standby Power STANDBY +VO2 ⊙★ MAIN +VO1 @★≡⊙ MODEL NO. HTCA2000R-D500E HTCA2000R-D600E HTCA2000R-D840E Min. Typ. Volt. Max. Peak Min. Typ. Volt. Max. Peak 0A 0A 0A 28.0A 24.0A 16.7A +50V +60V +84V 40A 33A 24A 40A 33A 24A 0A 0A 0A 1.0A 1.0A 1.0A +5V +5V +5V 1.0A 1.0A 1.0A 1A 1A 1A Symbol: "★" OVP built-in. "@" Adjustable. "≡" Load Sharing. "⊙" Installed with Or-ing diode. Remark: 1. All signals are reference with V02. HTCA2000R can provide maximum power 1400Watt while Vin at 90-180Vac and 2000Watt while Vin at 180-264Vac. MECHANICAL DIMENSIONS: MM [INCHES] WEIGHT: 2.30kg (5.1lb) DERATING CHART Hitron Electronics Cororation. B4-11, P.O. Box 26-110 Kaohsiung Export Processing Zone Kaohsiung 806 Taiwan TEL: 886-7-8210410/FAX: 886-7-8419917, 886-7-8210511/E-mail: [email protected] /Web-site: www.hitron-e.com 2 Sep. 11 2013 INPUT & OUTPUT CONNECTORS PIN ASSIGNMENT PIN NO. 3,4,5,6,7,8 9,10,11,12,13,14 19,43 22 23 25 26 27 28 31 32 33 34 35 36 37 38 39 40 41 42 44 45 46 47 ASSIGNMENT V0+ V0+5VS S-RTN DC_OK A0 Fan_Fail EN A1 A2 P0.14(Alert) nRest PS_PRNT CS TXD1 SCL OTW IHN SDA RXD1 AC_Fail H_POWER AC-G AC-N AC-L REMARKS Output voltage VO1 Return of output voltage VO1 +5V Signal Return of +5V Signal (Same level with VO-) Active High for DC OK Address A0 of I2C (Internal pull to High 3.3V) Active Low for Fan Fail Active Low to Enable Address A1 of I2C (Internal pull to High 3.3V) Address A2 of I2C (Internal pull to High 3.3V) Debug use & Alert for PM-Bus function (Active High to Run) Debug use(Active to Reset MCU) Pull to Low Current Share bus for VO1 Tx (RS232 for ISP) Clock Line of I2C Interface Active Low for Over Temperature Active Low to Inhibit Data Line of I2C Interface Rx (RS232 for ISP) Active Low for AC Fail Active Low for High Power AC-Earth/Ground Connection AC-Neutral Connection AC-Line Connection FRONT PANEL LED STATUS & MONITORING SIGNAL Condition OK Thermal Alarm Thermal Shutdown Defective Fan Blown AC Fuse in unit No AC <10mS (Single Unit) AC present but no within limits AC not present Over Voltage Shutdown Over Current Standby Front Panel LED Status AC OK DC OK Fault (Green) (Green) (Red) 1 1 0 1 1 Blinks 1 0 1 1 0 1 Monitoring Signal AC_Fail DC_OK Fan_Fail OTW PS_PRNT High High High High Low Low High High High High High Low High Low Low High Low Low Low Low 1 0 1 Low High High High Low 0 1 0 Low Low High High Low Blinks 0 0 Low High High High Low 0 0 0 Low High High High Low 1 0 1 High High Low High Low 1 1 Blinks 0 0 0 High High Low High High High High High Low Low Hitron Electronics Cororation. B4-11, P.O. Box 26-110 Kaohsiung Export Processing Zone Kaohsiung 806 Taiwan TEL: 886-7-8210410/FAX: 886-7-8419917, 886-7-8210511/E-mail: [email protected] /Web-site: www.hitron-e.com 3 Sep. 11 2013 I2C COMMAND FORMAT Note: 1. There are four types of I2C command ,Group A-D, as below for MCU in HTC2000R series. 2. The Frequency of I2C is set at 400KHz. 3. After getting the command, the Slave must reply the Master within the period between 1uS and 2mS to avoid "time-out" problem. 4. The time between Start bit of each byte format should be less then 400uS to avoid “Time-out” problem. I2C COMMAND LIST GROUP A COMMAND AAh A ACh A AEh B B C C BAh BCh C1h C2h C C3h C C4h C C5h C C6h C C7h C C8h C C9h C CAh C CBh C CCh C CDh D D D DAh DCh DEh DESCRIPTION Set Output Voltage in mV. Set High line Output Current in mA Set Low line Output Current in mA Turn on the main output. Turn off the main output. Read Fan 1 speed in RPM. Read Fan 2 speed in RPM. Read Output Voltage (Before Oring Diode) in mV Read Output Voltage (After Oring Diode) in mV. Read +5VSB Voltage (Before Oring Diode) in mV Read +5VS Voltage (After Oring Diode) in mV Read Ambient Temperature in OC./1000. Read Working Temperature in OC./1000. Read Output Current in mA. Read the setting Voltage in mV Read the High Power setting Current in mA Read the Low Power setting Current in mA Read Warming Status 1 : Warming, 0 : Normal Read equipment. Read Hardware Version. Read Software Version. REMARK Use 3 bytes binary value in mV and MSB first Use 3 bytes binary value in mA and MSB first Use 3 bytes binary value in mA and MSB first. N/A N/A Use 3 bytes binary value in RPM and MSB first. Use 3 bytes binary value in RPM and MSB first. Use 3 bytes binary value in mV and MSB first. Use 3 bytes binary value in mV and MSB first. Use 3 bytes binary value in mV and MSB first. Use 3 bytes binary value in mV and MSB first. Use 3 bytes binary value in OC./1000. and MSB first. Use 3 bytes binary value in OC./1000. and MSB first. Use 3 bytes binary value in mA and MSB first. Use 3 bytes binary value in mV and MSB first. Use 3 bytes binary value in mA and MSB first. Use 3 bytes binary value in mA and MSB first. 00h 00h 000b OTW AC-Fail Fan_F DC_OK H_Power One Length byte & n data bytes in ASCII code. One Length byte & n data bytes in ASCII code. One Length byte & n data bytes in ASCII code. Hitron Electronics Cororation. B4-11, P.O. Box 26-110 Kaohsiung Export Processing Zone Kaohsiung 806 Taiwan TEL: 886-7-8210410/FAX: 886-7-8419917, 886-7-8210511/E-mail: [email protected] /Web-site: www.hitron-e.com 4 Sep. 11 2013 ADDRESS DEFINITION A2 A1 A0 I2C Bits 7-1 EEPROM(24C02) Bits 7-1 0 0 0 0011 000 1010 000 0 0 1 0011 001 1010 001 0 1 0 0011 010 1010 010 0 1 1 0011 011 1010 011 1 0 0 0011 100 1010 100 1 0 1 0011 101 1010 101 1 1 0 0011 110 1010 110 1 1 1 0011 111 1010 111 Tx/Rx COMMAND FORMAT ASSIGNMENT DESCRIPTION F1 Read Fan 1 output F2 Read Fan 2 output V1 Read Output Voltage (Before Oring Diode) V2 Read Output Voltage (After Oring Diode) V3 Read +5VSB Voltage (Before Oring Diode) V4 Read +5VSB Voltage (After Oring Diode) SV Set Output Voltage in mV (ex. SV 50000) SH Set High power Output Current in mA (ex. SH 40000) SL Set Low power Output Current in mA (ex. SL 28000) C1 Read Output Current T1 Read Ambient Temperature T2 Read Working Temperature RW Read Output warning 1:warning 0:normal (OTW, AC_Fail, Fan_F, DC_OK, H_POWER) RV Read Output Voltage RC Read Output Current Rv Read Hardware Version & Software Version RE Read Equipment PU Power On PD Power Down CR Clear Record RR Read Record Hitron Electronics Cororation. B4-11, P.O. Box 26-110 Kaohsiung Export Processing Zone Kaohsiung 806 Taiwan TEL: 886-7-8210410/FAX: 886-7-8419917, 886-7-8210511/E-mail: [email protected] /Web-site: www.hitron-e.com 5 Sep. 11 2013 Tx/Rx COMMAND LIST COMMAND DESCRIPTION F1 Read Fan 1 speed in RPM F2 Read Fan 2 speed in RPM V1 Read Output Voltage (Before Oring Diode) in Volt V2 Read Output Voltage (After Oring Diode) in Volt V3 Read +5VSB Voltage (Before Oring Diode) in Volt V4 Read +5VS Voltage (After Oring Diode) in Volt T1 Read Ambient Temperature in OC T2 Read Working Temperature in OC C1 Read Output Current in mA SV Set Output Voltage in mV SH Set High line Output Current in mA SL Set Low line Output Current in mA RV Read the setting Voltage in Volt RC Read the setting Current in Amp RW Read Warming Status 1 : Warming, 0 : Normal OTW AC-Fail FAN_F PU Turn on the main output PD Turn off the main output Rv Read Hardware Version & Software version RE Read equipment CR Clear Record RR Read Record DC_OK H_Power Tx/Rx RECORD DEFINITION ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 RECORD NUMBER 0h 1h 2h 3h 4h 5h 6h 7h 8h 9h Ah Bh Ch Dh Eh Fh RECORD DESCRIPTION Power-off by out of range of AC input voltage Power-off by out of range of Ambient Temperature Power-off by out of range of Working Temperature Power-off by out of range of output current Power-off by RS232 Power-off by I2C Voltage setting is modified Current setting is modified Un-known N/A N/A N/A N/A N/A N/A N/A Hitron Electronics Cororation. B4-11, P.O. Box 26-110 Kaohsiung Export Processing Zone Kaohsiung 806 Taiwan TEL: 886-7-8210410/FAX: 886-7-8419917, 886-7-8210511/E-mail: [email protected] /Web-site: www.hitron-e.com REMARK AD1, AD2 T1 T2 OCP/OLP/SC N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 6 Sep. 11 2013