IS31SE5104 4-CH CAPACITIVE TOUCH SENSOR WITH AUTO CALIBRATION August 2015 GENERAL DESCRIPTION FEATURES The IS31SE5104 is a low power, fully integrated 4-channel solution for capacitive touch button applications. The chip allows electrodes to project sense fields through any dielectric such as glass or plastic. On-chip calibration logic continuously monitors the environment and automatically adjusts on-and-off threshold levels to prevent false sensor activation. The IS31SE5104 supports the 400kHz I²C serial bus data protocol and includes a field programmable slave address. An active low interrupt signal is generated on the INTB pin whenever a button event (touched or released) is detected. The triggered and cleared condition can be configured by setting the interrupt register. IS31SE5104 is available in either a QFN-16 (3mm × 3mm) or SOP-16 package. It operates from 2.7V to 5.5V over the temperature range of -40°C to +85°C. Four capacitive touch sensor controller Auto offset compensation Sensitivity adjustable with external capacitor or internal register Low power optimized for portable applications Interrupt output 400kHz fast-mode I²C interface 8kV ESD HBM Operating temperature TA = −40°C ~ +85°C QFN-16 (3mm × 3mm) and SOP-16 packages APPLICATIONS Mobile phones GPS PDAs TYPICAL APPLICATION CIRCUIT Figure 1 Typical Application Circuit Note 1: The IC should be placed far away from the mobile antenna in order to prevent the EMI. Note 2: The RS resistor should place as close as possible to reduce EMI. Note 3: The OUTx pin is open drain structure inside. To configure the OUTx pin as a logic signal output use a 100kΩ pull up resistor. Integrated Silicon Solution, Inc. – www.issi.com Rev. C, 08/05/2015 1 IS31SE5104 PIN CONFIGURATION Package Pin Configuration (Top View) 16 GND 15 OUT4 14 GND 13 OUT3 5 SCL 6 AD 7 SDA 8 SOP-16 CAP4 QFN-16 Integrated Silicon Solution, Inc. – www.issi.com Rev. C, 08/05/2015 2 IS31SE5104 PIN DESCRIPTION No. Pin Description 14,16 GND Ground. 2 15 OUT4 Channel 4 outputs. Pulled low when input sense channel is pressed. Leave floating if not used. 4 1 VCC Power supply. 5~8 2~5 CAP1 ~ CAP4 Input sense channel 1 ~ 4. Each channel should connect to GND if it is not used and disabled by the 01h register (Page 8). 9 7 AD I2C address setting. 10 6 SCL I2C serial clock. 11 8 SDA I2C serial data. 12 9 INTB Interrupt output, active low. 13 10 SDB Shutdown the chip when pulled low. 14~16 11~13 OUT1 ~OUT3 Channel 1 ~ 3 outputs. Pulled low when input sense channel is pressed. Unused channel should be left floating. Thermal Pad Connect to GND. SOP QFN 1,3 - Integrated Silicon Solution, Inc. – www.issi.com Rev. C, 08/05/2015 3 IS31SE5104 ORDERING INFORMATION Industrial Range: -40°C to +85°C Order Part No. Package QTY IS31SE5104-QFLS2-TR QFN-16, Lead-free 2500/Reel IS31SE5104-GRLS2-TR IS31SE5104-GRLS2 SOP-16, Lead-free 2500/Reel 50/Tube Copyright © 2015 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless Integrated Silicon Solution, Inc. receives written assurance to its satisfaction, that: a.) the risk of injury or damage has been minimized; b.) the user assume all such risks; and c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances Integrated Silicon Solution, Inc. – www.issi.com Rev. C, 08/05/2015 4 IS31SE5104 ABSOLUTE MAXIMUM RATINGS Supply voltage, VCC Voltage at any input pin Maximum junction temperature, TJMAX Storage temperature range, TSTG Operating temperature range, TA ESD (HBM) ESD (CDM) -0.3V ~ +6.0V -0.3V ~ VCC+0.3V 150°C -65°C ~ +150°C −40°C ~ +85°C 8kV 1kV Note: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other condition beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS TA = -40°C ~ +85°C, VCC = 2.7V ~ 5.5V, unless otherwise noted. Typical value are TA = 25°C, VCC = 3.6V. Symbol Parameter Condition Min. Typ. Max. Unit 5.5 V VCC Supply voltage ICC Quiescent power supply current VSDB = VCC = 3.6V 173 476 μA ISD Shutdown current VSDB = 0V, VCC = 5.5V 1.6 5.8 μA VHR Current Sink headroom voltage IOUT = 20mA, VCC = 3.6V 290 467 mV ∆CS Minimum detectable capacitance CS = 5pF (Note 1) 2.7 79 pF 0.2 Logic Electrical Characteristics VIL Logic “0” input voltage VCC = 2.7V 0.4 VIH Logic “1” input voltage VCC = 5.5V IIL Logic “0” input current VINPUT = 0V(Note 1) 5 nA IIH Logic “1” input current VINPUT = VCC(Note 1) 5 nA 1.4 V V DIGITAL INPUT SWITCHING CHARACTERISTICS (Note 1) Symbol Parameter Condition Min. Typ. Max. Unit 400 kHz fSCL Serial-Clock frequency tBUF Bus free time between a STOP and a START condition 1.3 μs tHD, STA Hold time (repeated) START condition 0.6 μs tSU, STA Repeated START condition setup time 0.6 μs tSU, STO STOP condition setup time 0.6 μs tHD, DAT Data hold time tSU, DAT Data setup time 100 ns tLOW SCL clock low period 1.3 μs tHIGH SCL clock high period 0.7 μs 0.9 μs tR Rise time of both SDA and SCL signals, receiving (Note 2) 20+0.1Cb 300 ns tF Fall time of both SDA and SCL signals, receiving (Note 2) 20+0.1Cb 300 ns Note 1: Guaranteed by design. Note 2: Cb = total capacitance of one bus line in pF. ISINK ≤ 6mA. tR and tF measured between 0.3 × VCC and 0.7 × VCC. Integrated Silicon Solution, Inc. – www.issi.com Rev. C, 08/05/2015 5 IS31SE5104 DETAILED DESCRIPTION The 8-bit chip address is sent next, most significant bit first. Each address bit must be stable while the SCL level is high. I2C INTERFACE The IS31SE5104 uses a serial bus, which conforms to the I2C protocol, to control the chip’s functions with two wires: SCL and SDA. The IS31SE5104 has a 7-bit slave address (A7:A1), followed by the R/W bit, A0. Set A0 to “0” for a write command and set A0 to “1” for a read command. The value of bits A1 and A2 are decided by the connection of the AD pin. After the last bit of the chip address is sent, the master checks for the IS31SE5104’s acknowledge. The master releases the SDA line high (through a pull-up resistor). Then the master sends an SCL pulse. If the IS31SE5104 has received the address correctly, then it holds the SDA line low during the SCL pulse. If the SDA line is not low, then the master should send a “STOP” signal (discussed later) and abort the transfer. The complete slave address is: Table 1 Slave Address Bit A7:A3 A2:A1 A0 Value 10001 AD 1/0 Following acknowledge of IS31SE5104, the register address byte is sent, most significant bit first. IS31SE5104 must generate another acknowledge indicating that the register address has been received. AD connected to GND, AD = 00; AD connected to VCC, AD = 11; AD connected to SCL, AD = 01; AD connected to SDA, AD = 10; Then 8-bit of data byte are sent next, most significant bit first. Each data bit should be valid while the SCL level is stable high. After the data byte is sent, the IS31SE5104 must generate another acknowledge to indicate that the data was received. The SCL line is uni-directional. The SDA line is bi-directional (open-collector) with a pull-up resistor (typically 4.7kΩ). The maximum clock frequency specified by the I2C standard is 400kHz. In this discussion, the master is the microcontroller and the slave is the IS31SE5104. The “STOP” signal ends the transfer. To signal “STOP”, the SDA signal goes high while the SCL signal is high. READING PORT REGISTERS To read the device data, the bus master must first send The timing diagram for the I2C is shown in Figure 2. The SDA is latched in on the stable high level of the SCL. When there is no interface activity, the SDA line should be held high. ____ the IS31SE5104 address with the R/W bit set to “0”, followed by the command byte, which determines which register is accessed. After a restart, the bus master must then send the IS31SE5104 address with The “START” signal is generated by lowering the SDA signal while the SCL signal is high. The start signal will alert all devices attached to the I2C bus to check the incoming address against their own chip address. Figure 2 ____ the R/W bit set to “1”. Data from the register defined by the command byte is then sent from the IS31SE5104 to the master (Figure 5). Interface timing Figure 3 Integrated Silicon Solution, Inc. – www.issi.com Rev. C, 08/05/2015 Bit transfer 6 IS31SE5104 Figure 4 Figure 5 Integrated Silicon Solution, Inc. – www.issi.com Rev. C, 08/05/2015 Writing to IS31SE5104 Reading from IS31SE5104 7 IS31SE5104 Table 2 Register Function Address Name Function Table Default 00h Configuration Register Set software shutdown mode and sensitivity 3 0000 0000 01h Channel Control Register Set the 4 channels enable 4 1111 1111 02h State Register 1 Store state of action for 4 channels 5 03h State Register 2 Show state of 4 channels changes or not 6 04h Interrupt Register Set interrupt function 7 0000 0000 Table 5 02h State Register 1 (Read only) Table 3 00h Configuration Register Bit D7 D6:D5 D4:D0 Bit D7:D4 D3:D0 Name SSD SS - Name - AS4: AS1 Default 0 00 00000 Default 0000 0000 The Configuration Register sets software shutdown mode and sensitivity. The State Register 1 stores state of action for 4 channels. SSD 0 1 Software Shutdown Enable Normal operation Software shutdown mode ASx 0 1 SS 00 01 10 11 Sensitivity Selection Normal sensitivity High sensitivity Low sensitivity Not a valid state Table 6 03h State Register 2 (Read only) Table 4 01h Channel Control Register Bit D7:D4 D3:D0 Name - CH4: CH1 Default 1111 1111 The Channel Control Register sets the 4 channels enable. CHx 0 1 Channel Enable Disable Enable Action State Bit Button released Button pressed Bit D7:D4 D3:D0 Name - SC4: SC1 Default 0000 0000 The State Register 2 shows state of 4 channels changes or not. State Change Bit No state change Button touched or released event occurs SCx 0 1 Table 7 04h Interrupt Register Bit D7:D6 D5:D0 Name ACI - Default 00 000000 The Interrupt Register sets interrupt function. ACI 00 01 10 11 Integrated Silicon Solution, Inc. – www.issi.com Rev. C, 08/05/2015 Automatically Clear Interrupt No auto clear Auto clear after 8ms Auto clear after 32ms Not a valid state 8 IS31SE5104 FUNCTIONAL BLOCK DIAGRAM Integrated Silicon Solution, Inc. – www.issi.com Rev. C, 08/05/2015 9 IS31SE5104 APPLICATION INFORMATION GENERAL DESCRIPTION The IS31SE5104 is an ultra low power, fully integrated 4-channel solution for capacitive touch-button applications. The chip allows electrodes to project sense fields through any dielectric such as glass or plastic. SENSITIVITY ADJUSTING Sensitivity can be adjusted by using an external capacitor (Typical 5pF) or programming an internal register. A high value of capacitor will lower the sensitivity; while a low value of capacitor will increase sensitivity. The SS bit of Configuration Register (00h) is used to modulate sensitivity. By setting the SS bit to “00” sensitivity is normal. Sensitivity is high when SS bit is set to “01”. Sensitivity is low when SS bit is set to “10”. Setting SS bit to “11” is not a valid state. OUTPUT CONTROL There are 4 output ports (OUT1~OUT4) and 4 capacitive sensor input channels (CAP1~CAP4). The output port will be pulled low to drive an externally connected LED (with current limiting resistor) or other device when a capacitance change is detected on the corresponding input channel. The OUT1~OUT4 ports are open drain type which require a 100kΩ pull up resistor when used for logic signaling. For example, in Figure 1, when a sensitivity channels detects a capacitance change, the corresponding LED is driven by current set by the limiting resistor. ACTION INFORMATION The action information is stored in the State Register (02h, 03h). If the AS bit is set to “0”, the corresponding channel is released. If the AS bit is set to “1”, the corresponding channels is pressed. If the SC bit is set to “0”, the corresponding channel has no status changing. If the SC bit is set to “1”, the corresponding channel has status changing. INTERRUPT SIGNAL A detected capacitance change on any of the CAP1~CAP4 inputs will cause the INTB pin to be pulled low. The INTB signal is used for notifying the MCU that a capacitance disturbance has been detected. The MCU through the I2C bus can identify which input experienced they capacitance change by reading the Status Register (02h, 03h). The INTB will return to high state once the MCU has accessed the Status Register 2 (03h). The ACI bit of Interrupt Register (04h) is used to configure the automatic interrupt clear function. If the ACI bit is set to “00”, the automatic interrupt clear Integrated Silicon Solution, Inc. – www.issi.com Rev. C, 08/05/2015 function is disabled. If the ACI bit is set to “01”, the function is enabled and the INTB pin will be automatically cleared after remaining low for 8ms. If the ACI bit is set to “10”, the INTB pin will be automatically cleared after staying low for 32ms. Setting ACI bit to “11” is not a valid state. AUTOMATIC CALIBRATION FUNCTION The IS31SE5104 integrates an auto-calibration logic block to continuously update the reference capacitance register to compensate for slow changes in the environment. Very low capacitive changes are neutralized by the auto-calibration logic. The advantage of auto-calibration is capacitive changes due to dirt, humidity, or temperature will not affect this device. However, extremely fast changes will not be detected because the capacitance disturbance is digitally filtered out. An auto-calibration cycle is performed every 2 seconds. CAP1~CAP4 capacitance is measured and the reference capacitance value in the hidden registers are updated. A detection cycle is performed every 16ms. The CAP1~CAP4 capacitance is measured and compared to the stored reference capacitance. A valid detection is when the CAP1~CAP4 capacitance differs from the stored reference capacitance value for two (2) detection cycles The device can be programmed to 3 sensitivity detection levels: Normal, High and Low. An interrupt is generated if over two detection cycles the measured capacitance exceeds the stored reference value. A detection of 32 steps higher difference is recognized as a capacitive change for normal sensitivity, 16 steps higher for high sensitivity and 64 steps higher for low sensitivity. SHUTDOWN MODE There are two methods to place the IC in shutdown mode, software or hardware. The shutdown mode can be used as a means of reducing power consumption. During shutdown mode all registers retain their data but capacitance changes are not detected. SOFTWARE SHUTDOWN By setting SSD bit of the Configuration Register (00h) to “1”, the IS31SE5104 will operate in software shutdown mode. In this shutdown mode, the device consumes only 1.6μA (typ.) current. HARDWARE SHUTDOWN The chip enters hardware shutdown mode when the SDB pin is pulled low, wherein the consumption current is the same as software shutdown, 1.6μA (Typ.). 10 IS31SE5104 CLASSIFICATION REFLOW PROFILES Profile Feature Pb-Free Assembly Preheat & Soak Temperature min (Tsmin) Temperature max (Tsmax) Time (Tsmin to Tsmax) (ts) 150°C 200°C 60-120 seconds Average ramp-up rate (Tsmax to Tp) 3°C/second max. Liquidous temperature (TL) Time at liquidous (tL) 217°C 60-150 seconds Peak package body temperature (Tp)* Max 260°C Time (tp)** within 5°C of the specified classification temperature (Tc) Max 30 seconds Average ramp-down rate (Tp to Tsmax) 6°C/second max. Time 25°C to peak temperature 8 minutes max. Figure 6 Classification profile Integrated Silicon Solution, Inc. – www.issi.com Rev. C, 08/05/2015 11 IS31SE5104 PACKAGE INFORMATION QFN-16 Integrated Silicon Solution, Inc. – www.issi.com Rev. C, 08/05/2015 12 IS31SE5104 SOP-16 Integrated Silicon Solution, Inc. – www.issi.com Rev. C, 08/05/2015 13 IS31SE5104 RECOMMENDED LAND PATTERN QFN-16 SOP-16 Note: 1. Land pattern complies to IPC-7351. 2. All dimensions in MM. 3. This document (including dimensions, notes & specs) is a recommendation based on typical circuit board manufacturing parameters. Since land pattern design depends on many factors unknown (eg. user’s board manufacturing specs), user must determine suitability for use. Integrated Silicon Solution, Inc. – www.issi.com Rev. C, 08/05/2015 14 IS31SE5104 REVISION HISTORY Revision A Detail Information Date Initial release 2013.12.25 B 1. Add Tape reel packing for SOP (Not release) 2014.11.10 C 1. Add land pattern 2. Add revision history 3. Revise Application Information 4. Update POD 2015.08.05 Integrated Silicon Solution, Inc. – www.issi.com Rev. C, 08/05/2015 15