LF3312 12-Mbit Frame Buffer / FIFO Preliminary Datasheet Features

LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Features
12,441,600-bit Frame Memory
74.25MHz Max Data Rate
May be Organized Into the Following
Configurations:
• 1,555,200 x 8-bit (single channel)
• 1,244,160 x 10-bit (single channel)
• 1,036,800 x 12-bit (single channel)
• 777,600 x 16-bit (width expansion - dual channel)
• 622,080 x 20-bit (width expansion - dual channel)
• 518,400 x 24-bit (width expansion - dual channel)
• 777,600 x 8-bit (each of two parallel channels)
• 622,080 x 10-bit (each of two parallel channels)
• 518,400 x 12-bit (each of two parallel channels)
Operating Modes:
• Random Access with External Address Port
(Single-channel)
• FIFO With Asynchronous I/O (Single-channel)
• FIFO With Asynchronous I/O (Dual-channel)
• Synchronous Shift Register (Single-channel)
• Synchronous Shift Register (Dual-channel)
• FIFO + shift register; Channel B Synchronized to
Channel A
• Shift register + FIFO; One channel Synchronized
to the other
Near-Full/Empty Flags With Programmable
Thresholds
Flexible Pointer Manipulation
• Write and Read Pointers may be independently jumped to arbitrary address locations
• Write or Read Pointers can be manipulated
in real-time based on external 24bit address
LF3312s may be Cascaded for depth and
width, supporting HDTV, Multiframe SDTV,
and other high resolution formats
• Seamless address space is maintained
with up to 16 cascaded devices
Built-in ITU-R BT.656 TRS detection and
Synchronization
Set & Clear Read/Write Pointer Control Pins
Choice of Control Interfaces:
• Two-wire Serial Microprocessor Interface
• Parallel Microprocessor Interface
Input Enable Control (Write Mask) for freezeframe applications
Output Enable Control (Data Skipping)
JTAG Boundary Scan - IEEE 1149.1
172 ball LBGA package
1.8V Internal Core Power Supply
3.3V I/O Supply
NOTE: This Preliminary Datasheet references LF3312BGC Engineering Samples
with an ES marking under the part designation.
Applications
DTV/HDTV Video Stream Buffer
Frame Synchronization
CCTV Security Camera Systems
Time Base Correction (TBC)
Freeze-Frame Buffer
Regional Read/Write for Picture-in-Picture (PIP)
Field-Based or Frame-Based Comb Filtering
Video Capture & Editing Systems
Deep Data Buffering
Video Special Effects (Rotation, Zoom)
Test Pattern Generation
Motion Detection or Frame-to-Frame Correlation
LOGIC Devices Incorporated
1
Video Imaging Product
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
LF3312 Overview
The LF3312 is a 12,441,600-bit memory device which can be configured by the user into either a twodata-port single-channel or a four-data-port dual-channel architecture. The input data ports may be clocked
simultaneously or asynchronously with one another and with the output ports. Using the four 12-bit data
ports provided, the user can operate the chip as one or two 8, 10, or 12-bit channels or as a single 16, 20, or
24-bit channel, without wasting any memory resources. Since reads are non-destructive, a given data value,
once written into the memory core, may be read as many times as desired. A user requiring more storage
can cascade up to sixteen LF3312s into a larger array.
A great deal of memory addressing flexibility is offered with the LF3312. In addition to simple clearing of the
Write and Read pointers, either pointer may be set/jumped to any location within the entire address space.
Real-time random-access Writing or Reading is also supported through an external address port.
The device is controlled by sixteen instruction words of eight bits each, which may be programmed or
verified via a standard I2C 2-wire serial or parallel microprocessor interface.
The 3-bit OPMODE control selects one of the chip’s operating modes, each of which has versatile submode
options:
- One-Channel FIFO With Asynchronous I/O
- Two-Channel FIFO; Both Channels Sychronized to External Signals
- One-Channel Synchronous Shift Register (Single Clock; User-set Latency)
- Two-Channel Synchronous Shift Register (Single Clock; User-set Latencies)
- One-Channel Framestore With Random Access
- Two-Channel FIFO; Channel A Synchronized to Channel B
- Two-Channel FIFO; Channel B Synchronized to Channel A
LF3312 Functional Block Diagram
SDA
6
TWO-WIRE SERIAL
INTERFACE
TDI
TDO
TRST
TMS
TCLK
JTAG
INPUT
DATA
PORTS
MEMORY
12Mbit
AOUT
OUTPUT
DATA
(x8,x10, x12)
PORTS
BOUT
.
.
(x8,x10, x12)
A/B WCLK
A/B WEN
A/B SET
A/B IEN
A/B CLR
A/B MARK
SCL
8
AIN
BIN
PARALLEL
INTERFACE
.
CE
WE
RE
ADDR
DATA
.
PROGRAM LOAD
FLAGS
INPUT
CONTROL
WRITE
POINTER
READ
POINTER
RANDOM ACCESS
ADDRESSING
A/B PE
A/B PF
A/B COLLIDE
RCLK
OUTPUT
CONTROL
A/B REN
RSET
RCLR
Video Imaging Product
LOGIC Devices Incorporated
2
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Figure 1. Dual Channel FIFO Mode Functional Block Diagram
AMARK
AWCLK
AWEN
AIEN
ACLR
ASET
AMARK
AIN11-0
CHIP_ADDR6-0
PROGRAM
PDATA
PADDR
CSB
RCLK
WRITE
CONTROL A
READ
AWCLK
7
8
6
REB
SDA
SCL
BCLR
BSET
BMARK
12
FLAG
GENERATOR A
MASTER
CONTROL
AOUT11-0
APF
APE
ACOLLIDE, BCOLLIDE
BPF
BPE
FLAG
GENERATOR B
I2C
MEMORY CELL ARRAY B
518,400 x 12-bit
622,080 x 10-bit
777,600 x 8-bit
12
BWCLK
BWEN
BIEN
AOE
MEMORY CELL ARRAY A
518,400 x 12-bit
622,080 x 10-bit
777,600 x 8-bit
12
WEB
BIN11-0
AREN
RSET
RCLR
CONTROL A
12
BOE
BWCLK
WRITE
CONTROL B
BOUT11-0*
RCLK
READ
CONTROL B
BREN
RSET
RCLR
BMARK
Video Imaging Product
LOGIC Devices Incorporated
3
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Figure 2. Single Channel FIFO Mode Functional Block Diagram
AMARK
AWCLK
RCLK
AWEN
AIEN
WRITE
CONTROL A
ACLR
ASET
AMARK
PDATA
PADDR
CSB
AREN
RSET
RCLR
AOE
MEMORY CELL ARRAY
1,036,800 x 12-bit
1,244,160 x 10-bit
1,555,200 x 8-bit
12
AIN11-0
CHIP_ADDR6-0
PROGRAM
READ
CONTROLA
CONTROL
12
AOUT11-0
7
APF
8
6
REB
WEB
SDA
SCL
FLAG
GENERATOR
MASTER
CONTROL
ACOLLIDE
APE
I2C
Figure 3. Random Access Mode Functional Block Diagram
AWCLK
AWEN
AIEN
ACLR
ASET
AMARK
PDATA
PADDR
CSB
MEMORY CELL ARRAY
1,036,800 x 12-bit
1,244,160 x 10-bit
1,555,200 x 8-bit
7
AREN
RSET
RCLR
AOE
12
AOUT11-0
8
6
REB
WEB
SDA
SCL
ADDR11-0 = BIN11-0
LOGIC Devices Incorporated
READ
CONTROL
12
AIN11-0
CHIP_ADDR6-0
PROGRAM
RCLK
WRITE
CONTROL A
MASTER
CONTROL
I2C
24
12
ADDRESS
CONTROL
4
12
ADDR23-12 = BOUT11:0
Video Imaging Product
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Operating Modes
Asynchronous single-channel FIFO mode (OPMODE = 3)
In OPMODE 3, the LF3312 is configured as a single channel First-In-First-Out 12Mbit memory, with
independent read and write clocks to allow for asynchronous operation. This mode is ideal for buffering or
burst data applications. Arbitrary write/read pointer jumping is supported in all FIFO modes. In this mode
the device can re-time a data stream according to a read sync signal (RSET or RCLR) and either ITU-R656
Timing Reference Signals (TRS) embedded within the incoming (video) data or the falling edge of a write
sync signal applied to ACLR, ASET, or AMARK.
As a single channel FIFO, the LF3312 must have AWCLK and BWCLK tied together as must be AWEN
with BWEN, and AIEN with BIEN. The input (write) and output (read) clocks need not be synchronous with
one another, although the memory core will eventually fill or empty if they differ in average frequency. After
it “fills,” the LF3312 continues writing and the oldest data gets written over. If the memory core “empties”
(and neither the read nor write pointer have been set or cleared during run-time) the read pointer stops
incrementing, and the device re-reads the last written sample until more data is written. In either case,
when the read and write addresses reach equality, the ACOLLIDE flag will go high, to alert the host. The
almost-full and almost-empty flags provide advance warning of these conditions whenever user-selected
“fullness” or “emptiness” thresholds, expressed in approximate eightieths of the memory core size, are
exceeded. For example, if the 1/80 and 79/80 thresholds are enabled, flag APE will go HIGH whenever the
read pointer lags behind the write pointer by less than 1/80 of the memory space, and flag APF will go HIGH
whenever the read pointer leads the write pointer by this amount. (Calculations are performed modulo the
total address space.) The data input and output are sequential and the timing between write and read sync
signals dynamically determines the effective delay (depth) of the FIFO.
The ‘stop reading when empty’ FIFO-mode behavior can be avoided by making sure LOAD is HIGH and
issuing any write or read pointer SET or CLR command at any time. This effectively gets the device out
of this ‘read-pointer-halting’ mode from that point onwards, but invalidates the flags. Random Access Mode
allows free manipulation of the r/w pointers, and never halts the read pointer without being commanded
to do so using AREN or BREN. Since Random Access mode naturally increments the r/w pointers
sequentially, like in FIFO mode, it may be a better mode to use if pointer manipulation of a single-channel
of memory is desired.
Dual-channel asynchronous FIFO mode (OPMODE = 7; power-on default)
OPMODE 7 operates identically to the single channel FIFO (OPMODE 3), with two independent chanels.
In dual-channel asynchronous FIFO mode, the device can accept two asynchronous data streams and
automatically adjust the latency of each to bring it into alignment with an output sync signal applied to RSET
or RCLR. Again, the user may reference input synchronization either to ACLR, ASET, BCLR, and BSET,
to AMARK and BMARK, or to embedded TRS. The data read/output clock need not be synchronous with
either of the two input clocks, which likewise need not be synchronous with one another. If memory core
A or B “empties“ or “fills“ completely, ACOLLIDE and/or BCOLLIDE respectively, will be set accordingly if
the write and read pointers collide.
The data Word that BMARK ‘marks’ (by going LOW during that xWCLK cycle) in the input data stream
will be the first synchronized AOUT/BOUT data word. If N full frames of Channel A data have been
loaded into AIN before the first Channel B data frame is loaded into BIN, the second frame of B channel
data will be synchronized to the (N+1)th Channel A frame. (there will be N frames difference between
Channel A and B).
Video Imaging Product
LOGIC Devices Incorporated
5
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Operating Modes
Single-channel synchronous shift register mode (OPMODE = 0)
In OPMODE 0, the LF3312 becomes a single channel shift register with programmable total latency up to
224-8 clock cycles. Writes and reads occur simultaneously, hence synchronous operation.
In OPMODE 0, the user provides a single clock for both the input and output clocks and specifies a desired
input-to-output data path latency, (ALAT) via the control interface. AWCLK, BWCLK, and RCLK must be tied
together, as should AWEN, BWEN, AREN, and BREN. When activated, ALAT will begin to countdown, and
once expired, will allow the inputs to begin to appear on the outputs. In OPMODE 0, ALAT countdown can
be activated in two ways. The first occurs when the first enable is brought LOW after the LOAD signal has
been set HIGH after MPU programming. The second is by bringing LOAD HIGH once MPU programming
complete, after the enables have been brought LOW.
Dual-channel synchronous shift register mode (OPMODE = 4)
The operation of dual-channel shift register mode is identical to single-channel operation, with the addition
of a second independent channel. The latency for each channel is independent and set by the user.
The user must also supply a single clock to tie AWCLK, BWCLK, and RCLK together, and must load the
respective desired constant latency for each channel, (ALAT, BLAT), via the microprocessor bus. ALAT
and BLAT are activated in the same manner as in OPMODE 0, with the respective inputs being made
available on the outputs once ALAT or BLAT expire. In this mode, AWEN and AREN must be tied together,
as must be BWEN and BREN.
Dual-channel master/slave mode (OPMODE = 5)
OPMODE 5 is one of two master/slave synchronizing modes where two data streams are written into the
LF3312 at independent rates and with independent TRS timing information. In this mode, both channels
are synchronized together based on the sync data supplied to channel A or by the embedded TRS data
within the A channel.
When in OPMODE 5, channel A operates as a fully synchronous master shift register, to which the data in
asynchronous FIFO channel B is re-timed. The user drives AWCLK and RCLK from the incoming AIN data
stream’s sample clock, and BWCLK from the BIN data stream’s clock. The user also specifies whether sync
timing will be derived from TRS words embedded within the incoming data streams or from signals applied
to ACLR and ASET or to AMARK and BMARK. AWEN, AREN and BREN must be tied together to maintain
constant reference latency through channel A and to synchronize the outputs. When a MARK occurs, the
signal MARK_ACTIVE_RSET when set high, allows the read pointer to be set to the current value of the
write pointer “ALAT” RCLK cycles later. If the user sets MARK_ACTIVE_RSET = 0, the LF3312 will ignore
the internal read pointer set.
Dual-channel slave/master mode (OPMODE = 6)
OPMODE 6 is the reverse of OPMODE 5, with the difference being that the two streams are synchronized to
the timing information applied to the B channel or embedded within the B channel as TRS data.
This OPMODE is identical to the previous, except that channel A is the slave FIFO and channel B is the
master shift register, and RCLK needs to be tied to BWCLK, and BWEN needs to be tied to BREN and
AREN. Similarly to mode 5, when a MARK occurs, the signal MARK_ACTIVE_RSET when set high, allows
the read pointer to be set to the registered value of the write pointer BLAT number of RCLK cycles later. If
the user sets MARK_ACTIVE_RSET = 0, the LF3312 will ignore the internal read pointer set.
LOGIC Devices Incorporated
6
Video Imaging Product
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Operating Modes
Random Access mode (OPMODE = 1)
Random Access mode is a single-channel FIFO mode, with the capability of either full-time write or read
pointer Random Accessability. This mode also supports write and read pointer jumps to arbitrary locations
throughout the address space. Unlike Asynchronous Single-Channel FIFO mode (OPMODE=3), Random
Access mode does not disable memory reads when the read pointer catches up to the write pointer.
Write pointer manipulation can be done through setting (jumping) the write pointer to the 24bit address
via the BIN and BOUT ports or to the ALATENCY configuration register. Read pointer manipulation can
be done through setting (jumping) the write pointer to the 24bit address via the BIN and BOUT ports or
to the BLATENCY configuration register. Periodic write and read pointer jumping can be accomplished by
supplying an address through either the BOUT/BIN address or the A or BLATENCY registers. Continuous
random access can only be accomplished through the use of the BOUT/BIN ports. When the write/read
pointers are not being set to an address, they increment sequentially.
In OPMODE 1, when BSET = 1 and BCLR = 0 the write pointer is set to the address supplied by
the BOUT/BIN ports when ASET is brought LOW. AWCLK and BWCLK must be tied together as must
AWEN and BWEN. In other words, on each active write clock cycle (rising edge of AWCLK for which
AWEN was LOW two rising edges of AWCLK previously), the user directs the write pointer to any
desired memory location, using what are otherwise the second channel data input and output ports. In
this application, BOUT[11:0] denotes the vertical (row) component, and BIN[11:0], the horizontal
(column) component, of a Cartesian set. Setting the control register ROW_LENGTH to the frame’s line
(row) length internally defines the Cartesian coordinates. Or, if desired, the concatenation of BOUT[11:0] in
front of BIN[11:0] represents a single 24-bit linear address. The user governs the mapping of (BOUT,BIN)
to the internal memory space by setting the parameter ROW_LENGTH such that ADDRESS = BOUT *
ROW_LENGTH + BIN. A ROW_LENGTH setting of 0 is interpreted as 4096, such that ADDRESS = a
24-bit concatenation of {BOUT,BIN} for this particular value. For a standard D1 video application with 1716
samples per line, the user would set ROW_LENGTH to 1716 decimal = 6B4 hex. Offset circuitry within the
LF3312 permits the user to cascade several chips in parallel and to use them collectively as a single large
memory with a seamless address space. Data are read out sequentially by rising edges of RCLK, under
the control of AREN (read enable), RSET (read pointer force to constant), and RCLR (read pointer clear to
0). Holding ASET LOW keeps the device continuously in random access write mode. Releasing ASET to its
HIGH state causes the chip to continue to write sequentially from the last-loaded address.
In OPMODE 1, when BCLR = 1, BSET = 0, MARK_SEL = 1, the read pointer is set to the address
supplied by the BOUT/BIN ports when RSET is brought LOW. AWCLK and BWCLK must be tied together
as well as AREN and BREN. As mentioned above, BOUT[11:0] represents the upper bits or the vertical
(row) address, whereas BIN[11:0] represents the lower bits or the horizontal (column) address. Releasing
RSET HIGH causes the read address pointer to increment from its last assigned location to the next
sequential address.
Video Imaging Product
LOGIC Devices Incorporated
7
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Cascading Devices for Depth Expansion
Multiple devices can be cascaded to deepen the address space. The usable 24bit address space is simply
extended for every additional device that is cascaded.
Internally, the LF3312 has a 24bit address space. When cascading LF3312s, each device’s write and read
pointers behave identically. The LF3312 was designed to be cascaded in parallel. That is, the inputs of each
device are tied together. The input data word (the data word placed on the AIN input port) is to be common
for all devices. Similarly, the outputs of all devices are tied together. Only one device drives the shared
output bus at one time, controlled automatically through internal bus enables.
Each device in a cascade of N devices is responsible for 1/N of the address space. That is, each device
writes and/or reads based on the common W/R pointer locations and where that particular device sits in
the cascade. Configuration Register C[3:0] (BASE_ADDR) is used to define each device’s place in the
cascade.
When cascading LF3312s, only singe-channel modes are supported (OPMODES 0 to 3). All write enables
AWEN/BWEN and AIEN/BIEN must be tied together, as must read enables AREN/BREN (see the device
connection diagram below).
The configuration registers of each device must be programmed identically, depending on mode/function,
except for Register C. Register C defines which region of the 24bit address space the particular device is
responsible for. Within Register C, there is a 4bit BASE_ADDR and 4bit CASCADE word. BASE_ADDR
determines the region of address space each device controls, and CASCADE defines how many devices
are in cascade. Register C effectively is programmed as “Chip n of N”.
Figure 4. Device Connection Example: Two Cascaded Devices
LF3312_1
IEN
AIN11-0
ADDR11-0
12
12
RCLK
RCLK
AREN
BREN
REN
RSET
RCLR
RSET
RCLR
.
.. .
.
.
..
.
.. .
ASET
BSET
ACLR
BCLR
WEN
AWCLK
BWCLK
ASET
BSET
ACLR
BCLR
AWEN
BWEN
AIEN
BIEN
.
. .
WCLK
AIN
AOUT
BIN
BOUT
12
12
AOUT11-0
ADDR23-12
LF3312_2
. .
LOGIC Devices Incorporated
8
RCLK
AREN
BREN
.
.
AWCLK
BWCLK
ASET
BSET
ACLR
BCLR
AWEN
BWEN
AIEN
BIEN
RSET
RCLR
AIN
AOUT
BIN
BOUT
Video Imaging Product
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Device Configuration
Programming
the LF3312
The LF3312 has two MPU interfaces. The first is a standard two wire serial interface following the I2C
protocol. The second is a parallel interface allowing the user to write a byte of data at a time to the
configuration registers. When the user wishes to use the serial interface, the PROGRAM pin must be set
LOW, while a HIGH selects the parallel interface. To provide users with more flexibility, the control registers
have been combined with a “working latch” . Ultimately, the register-latch combination allows users to
update the configuration registers during chip operation, and then to transfer the register contents to all
working latches simultaneously using the LOAD signal. When high, the LOAD signal allows the LF3312
to be pre-programmed during operation, and once brought low after programming updates the working
latches allowing the new changes to take effect. LOAD can also be maintained low to allow changes to the
configuration registers to be immediately reflected in the working latches.
Serial MPU
Interface
When the PROGRAM pin is LOW, the serial interface is active. Up to 16 LF3312 devices can be connected
to and programmed by the serial interface. The two wire interface is composed of an SCL clock pin and a
bi-directional SDA data pin. When inactive, SDA and SCL are forced HIGH by external pull up resistors.
Data transmission is achieved over the SDA pin and must remain constant during the logical HIGH portion
of the SCL clock pulse. The level of SDA, while SCL is HIGH, is interpreted as the appropriate bit value as
will be shown later. Changing the data on SDA must only occur when SCL is low, because any changes
to SDA while SCL is HIGH is interpreted as a start or stop request, which are shown in Figure 7 with an
example data transfer in Figure 8.
The first operation to begin programming the LF3312 through the serial interface, is to send a start signal.
When the interface is inactive, a HIGH to LOW transition must be sent on SDA while SCL is HIGH, notifying
all connected devices (slaves) to expect a data transmission. When transferring data, the MSB of the eight
bit sequence is the first bit to be transmitted to or from the master or slave. The first byte of data to be
transmitted on SDA must consist of the 7-bit base address of the slave, along with an 8th READ/WRITE bit
as the LSB, which describes the direction of the data transmission. The slave whose 7-bit CHIP_ADDR6-0,
matches the 7-bit base address sent on SDA, will send an acknowledgement back to the master by bringing
SDA LOW on the 9th SCL pulse.
During a write operation, if the slave does not send an acknowledgment back to the master device, SDA is
left high which forces the master to generate a stop signal. In contrast, during a read operation, if there is no
acknowledgement back from the master device, the LF3312 interprets this as if it were the end of the data
transmission, and leaves SDA high, allowing the master to generate its stop signal.
Figure 7 - I2C Start and Stop Signals
Stop Signal
Start Signal
LOGIC Devices Incorporated
SDA
SDA
SCL
SCL
9
Video Imaging Product
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Device Configuration
There are four operations that can be performed between the master and the slave. They are: Write to
consecutive registers, write to a single control register, read from consecutive registers and read from a
single register. To write to consecutive control registers, a start signal and base address must be sent
with the R/W bit as described above. After the acknowledgment back from the appropriate slave, the
8-bit address of the target control register must be written to the slave with the R/W bit LOW. The slave
then acknowledges by setting SDA LOW. The data byte to be written into the register can now be
transferred on SDA. The slave then acknowledges by pulling SDA LOW on the next positive going pulse
of SCL. The first control register address loaded into the LF3312 is considered as the beginning address
for consecutive writes, and automatically increments to the next higher address space. Therefore after the
acknowledgement, the data byte to configure register (first address + 1) can now be transferred from master
to slave. At any point a stop signal can be given to end the data transfer. To write to a single control register,
the same technique can be applied adding a stop signal after the first data write.
To read from consecutive control registers, the master must again give the start signal followed by a
base address with the R/W bit = 0, as if the master wants to write to the slave. The appropriate slave
then acknowledges. The master will then transfer the target register address to the slave and wait for
an acknowledge. The master will then give a repeated start signal to the slave, along with the base
address and R/W bit this time HIGH signifying a read and wait for an acknowledge. The user must write
to the LF3312 to select the appropriate initial target register. Otherwise the starting position of the read is
uncertain. Once the LF3312 acknowledges, the next byte of data on SDA is the contents of the addressed
register sent from the device. If the master acknowledges, the LF3312 will send the next higher register’s
contents on the following byte of data. To read from only one register is the same procedure as for
consecutive reading with a stop signal following the transfer of the register’s contents.
Figure 8 - I2C Example of transferring 11001101 on SDA
1
2
3
4
5
6
7
8
SCL
SDA
Parallel MPU
Interface
The parallel MPU interface can be used to write instructions to the control registers or to read them back for
verification. When the PROGRAM pin is HIGH, the parallel interface is selected. An external processor can
write into an internal register by setting PADDR to the desired register address, selecting the chip using the
CSB pin, setting PDATA to the desired value and then pulsing WEB LOW. The data will be written into the
selected register when both WEB and CSB are LOW, and will be held when either signal goes HIGH. To
read from a control register the processor must set PADDR to the desired address, select the chip with the
CSB pin, and then set REB LOW. The chip will then drive PDATA with the contents of the selected register.
After the processor has read the value from PDATA, REB and CSB should be set HIGH. The PDATA pins
are turned off (High Impedance) whenever CSB or REB are HIGH or when WEB is LOW. The chip will only
drive these pins when both CSB and REB are LOW and WEB is HIGH. One can also ground the REB pin
and use the WEB pin as a read/write direction control and use the CSB pin as a control I/O strobe.
Video Imaging Product
LOGIC Devices Incorporated
10
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Device Configuration
Parallel
Interface
Cont’d
Figure 5 - Normal Reading and Writing From a Control Register
Read Cycle - Normal Mode
CSB
tCSU
WEB
tCSPW
tCSU
REB
tCSU
PADDR[5:0]
tCDLY
tCZ
PDATA[7:0]
Write Cycle - Normal Mode
CSB
WEB
tCSU
tCSPW
tCSU
REB
tCSU
PADDR[5:0]
tCHD
tCSU
PDATA[7:0]
Figure 6 - Reading and Writing From a Control Register with REB Held Low
Read Cycle - REB held low
tCSPW
CSB
WEB
tCSU
PADDR[5:0]
tCDLY
tCZ
PDATA[7:0]
Write Cycle - REB held low
tCSPW
CSB
WEB
tCSU
PADDR[5:0]
tCSU
tCHD
PDATA[7:0]
LOGIC Devices Incorporated
11
Video Imaging Product
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Detailed Signal Definitions
Power
VCC INT - Internal Core Power Supply
+1.8V power supply. All pins must be connected.
VCC O - Output Driver Power Supply
+3.3V power supply. All pins must be connected.
Clocks
AWCLK - Write Clock A
Data present on AIN11-0 is written into the LF3312 on the rising edge of AWCLK when AWEN was LOW
for the previous rising edge of AWCLK.
BWCLK - Write Clock B
In two-channel modes(OPMODES 4-7), data present on BIN11-0 is written into the LF3312 on the rising
edge of BWCLK when BWEN is LOW. In one-channel modes(OPMODES 0-3), BWCLK must be tied
to AWCLK.
RCLK - Read Clock
In single channel modes, data is read from the LF3312 and presented on the output port (AOUT11-0)
after a rising edge of RCLK while AREN and AOE are LOW. In two-channel mode, data is also read
from the LF3312 and presented on the output port (BOUT11-0) after a rising edge of RCLK while BREN
and BOE are LOW.
Inputs
AIN11-0 - Data Input A
AIN11-0 is the 12-bit registered data input port. Bit 11 is the MSB in all modes. AIN1-0 are ignored in
10-bit mode and AIN3-0 are ignored in 8-bit mode. Any such unused inputs should either be tied to
ground or driven to proper logic levels by external logic.
BIN11-0 - Data Input B
In dual-channel modes (OPMODES 4-7), BIN11-0 is the 12-bit registered data input port in all dual channel
FIFO modes. Bit 11 is the MSB in all modes. BIN1-0 are ignored in 10-bit mode and BIN3-0 are ignored
in 8-bit mode. Unused inputs should be tied off to ground or driven to proper logic levels by external logic.
In single-channel modes (OPMODE 0-3), BIN11-0 can act as a 24bit external address port (ADDR).
CHIP_ADDR6-0 - Chip Address (CA6-0)
CHIP_ADDR6-0 determines the LF3312’s address on the two-wire microprocessor bus. Each LF3312
chip’s 7-bit two-wire serial microprocessor interface address is equal to its CHIP_ADDR6-0.
SCL - Serial Clock Input
SCL is a standard two-wire serial microprocessor interface clock pin. With this chip, it functions as a
dedicated input, since this part cannot be the master on an two-wire serial microprocessor interface.
ADDR23-0 - External Random Access Read/Write Address Port
(OPMODE 0-3) ADDR23-0 is a virtual 24-bit memory address port, available in single channel modes.
ADDR23-0 is a concatenation of the BIN and BOUT data ports. BIN11-0 specifies ADDR11-0 (X/Columncoordinate) and BOUT11-0 specifies ADDR23-12 (Y/Row-coordinate). The 24bit address is a purely linear
address when the instruction register ROW_LENGTH is equal to 0(default). When ROW_LENGTH is a
non-zero value, the memory is set to have a row (line) length of ROW_LENGTH.
PADDR5-0 - Parallel Microprocessor Interface Address Port
PADDR5-0 is the 6-bit address port for the parallel microprocessor interface. When inactive, it transitions
to a high impedance state.
Video Imaging Product
LOGIC Devices Incorporated
12
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Detailed Signal Definition
Input/Output
PDATA7-0 - Parallel Microprocessor Interface Data Port
PDATA7-0 is the 8-bit data port for the parallel microprocessor interface. When inactive becomes high
impedance.
SDA - Serial Data I/O
SDA is the standard bidirectional data pin of a two-wire serial microprocessor interface.
External pullup is required on SDA.
BOUT11-0 - Data Output B
In two-channel modes(OPMODES 4-7), BOUT11-0 is the 12-bit registered data output port. BOUT[11]
is always the MSB. In 10-bit mode, bits 1 and 0 are tristated. In 8-bit mode, bits 3-0 are tristated.
All active bits are updated on each rising edge of RCLK when BREN is LOW. In OPMODE 0-3 ,
BOUT11-0 can act as the upper word of the 24bit external address ADDR if ROW_LENGTH is equal to
0, or Y-coordinate address if ROW_LENGTH is some value other than zero. BOUT11-0 represents a
portion of the read address port when executing an RSET, if and only if AREN=0, MARKSEL=1, BCLR=1.
BOUT11-0 represents a portion of the write address portwhen executing an ASET, if and only if AWEN=0,
ACLR=1, BSET=1. For more details on RSET and ASET, please refer to their signal definitions.
Controls
ACLR - Channel A Write Pointer Clear
When ACLR is brought LOW, the next rising edge of AWCLK will bring the current value on AIN[11:0] into
memory Channel A, address 0. Whenever ACLR is HIGH, the destination for AIN[11:0] will be controlled
by ASET. The user may program ACLR such that either its falling edge or its LOW state is active. If its
LOW state is active, holding this pin LOW will hold the write address in its zero position continuously. This
control takes effect only when AWEN is LOW.
BCLR - Channel B Write Pointer Clear / Channel A Write Random Select
In dual-channel modes (OPMODE = 4-7), this pin clears the Channel B Write Pointer, in the same manner
that ACLR clears the Channel A Write Pointer, and the user may program it to be falling edge or LOW state
active. In single-channel modes (OPMODE = 0-3), this pin and control MARKSEL govern the action of
RSET. In OPMODES 4-7, this control takes effect only when BWEN is LOW.
ASET - Channel A Write Pointer Set
This control is active only when ACLR is HIGH. Bringing ASET LOW will cause the next rising edge of
AWCLK to bring the current value on AIN[11:0] into memory A, at the address specified by ALAT, or
if OPMODE = 0-3 and BSET = 1, at the address whose Cartesian coordinates are present on BOUT
and BIN. Whenever ASET and ACLR are HIGH, the next rising edge of AWCLK will bring the current
AIN[11:0] data value into the next-higher address in sequence. ASET may be programmed to be either
edge-triggered, in which case it affects the write pointer for only one clock cycle following a falling edge,
after which incrementing resumes, or level-triggered, in which case it affects the write pointer until it is
brought HIGH. For continuous random access write operation, holding ASET LOW and programming it
to be level-triggered will provide the needed continuous write pointer override. This control takes effect
only when AWEN is LOW.
BSET - Channel B Write Pointer Set
In two-channel modes (OPMODE = 4-7), this pin’s impact on the B write pointer is analogous to that
of ASET on the A write pointer, and the user may program the pin’s action to be either edge- or leveltriggering. In one-channel modes, BSET determines whether ASET forces the write address pointer to
ALAT (BSET = 0) or to BOUT,BIN (BSET = 1). In OPMODES 4-7, this control takes effect only when
BWEN is LOW.
LOGIC Devices Incorporated
13
Video Imaging Product
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Detailed Signal Definitions
AMARK - Channel A Write Address Pointer Mark
In single-channel mode, bringing this bit LOW will cause an internal register to store a copy the current
value of the write address pointer, for subsequent use in synchronizing the corresponding read address
pointer to the same location. Unlike ACLR and ASET, this control does not affect the write pointer value
itself. The system must use AMARK instead of ACLR if the entire memory core can be filled between
sequential falling edges of the sync reference signal. In contrast, the system must use ACLR or ASET to
establish a definite relationship between the internal address and the data stream, as in random access
read mode.
BMARK - Channel B Write Address Pointer Mark
(active only in dual channel modes, OPMODE = 4-7) Bringing this bit LOW will cause an internal register
to store a copy the current value of the Channel B write address pointer, for use in synchronizing the
corresponding read address pointer to the same location. This signal does not affect the value of the
memory B write address pointer itself.
RSET - Read Address Pointer Set
In dual-channel modes (OPMODE = 4-7), if AREN is LOW, bringing RSET LOW will force read address
pointer A to ALAT (if MARK_SEL is HIGH) or to the value most recently captured from using AMARK (if
MARK_SEL is LOW). If BREN is LOW, bringing RSET LOW will force read address pointer B to BLAT
(if MARK_SEL is HIGH) or to the value most recently captured by BMARK (if MARKSEL is LOW). In
single-channel modes (OPMODE = 0-3), if AREN is LOW, bringing RSET LOW will force the read address
to the most recently marked value (MARK_SEL LOW), to BLAT (MARKSEL HIGH and BCLR LOW), or
to BOUT,BIN (MARK_SEL is HIGH and BCLR is HIGH). This pin may be programmed to be either falling
edge or level LOW active.
RCLR - Read Address Pointer Clear
Bringing RCLR LOW causes the next rising edge of RCLK to force the read address pointer (OPMODE
0-3) or pointers (OPMODE 4-7) to zero. This pin may be programmed to be active on its falling edge
or in its LOW state. In single-channel mode, it can reset the read pointer only when AREN is LOW. In
dual-channel mode, it can reset read pointer A only if AREN is LOW, and read pointer B only if BREN
is LOW.
AWEN - Write Enable A
If AWEN is LOW, data on AIN11-0 is written to the device on the rising edge of AWCLK. When AWEN
is HIGH, the device ignores data on AIN and holds the write pointer. The user must anticipate the use
of AWEN by one cycle. Therefore when desiring not to write a sample, AWEN must be brought high
the cycle before.
BWEN - Write Enable B
If BWEN is LOW, data on BIN11-0 is written to the device on the rising edge of BWCLK. When BWEN
is HIGH, the device ignores data on BIN and holds the write pointer. The user must anticipate the
use of BWEN by one cycle. Therefore when desiring not to write a sample, BWEN must be brought
high the cycle before. In single channel modes (OPMODES 0-3), BWEN must be tied to AWEN.
AIEN - Memory Write Enable A (Write Masking)
AIEN is used to enable/disable writing into the memory core. A LOW on AIEN enables writing, while a HIGH
on AIEN disables writing. The internal A write address pointer is incremented by AWEN regardless of the
AIEN level. If disabling of AIEN is never desired, tie AIEN LOW.
BIEN - Memory Write Enable B (Write Masking)
BIEN is used to enable/disable writing into the memory core. A LOW on BIEN enables writing, while a HIGH
on BIEN disables writing. The internal A write address pointer is incremented by BWEN regardless of the
BIEN level. If disabling of BIEN is never desired, tie BIEN LOW.
Video Imaging Product
LOGIC Devices Incorporated
14
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Detailed Signal Definitions
AREN - Read Enable A
If AREN is LOW and the output port is enabled, data from Channel A is read and presented on AOUT11-0
after tD has elapsed from the rising edge of RCLK. If AREN goes HIGH, the last value loaded into Channel
A output register will remain unchanged and the read pointer will be held. The user must anticipate the
use of AREN by one cycle. Therefore when desiring not to read a sample, AREN must be brought high
the cycle before.
BREN - Read Enable B
If BREN is LOW and the output port is enabled, data from Channel B is read and presented on BOUT11-0
after tD has elapsed from the rising edge of RCLK. If BREN goes HIGH, the last value loaded into Channel
B output register will remain unchanged and the read pointer will be held. The user must anticipate the
use of BREN by one cycle. Therefore when desiring not to read a sample, BREN must be brought high
the cycle before.
PROGRAM - Serial/Parallel Interface Selector
When the user wishes to use the serial microprocessor to configure the LF3312, the PROGRAM pin must
be set LOW, whereas if he or she wishes to use the parallel interface, PROGRAM must be set HIGH.
LOAD – Instruction Load
Bringing asynchronous control LOAD LOW updates the working instruction latches to match the current
contents of the instruction preload latches. Holding it LOW causes the working latches to reflect all ongoing
instruction preloads. Holding it HIGH permits the user to preset the instruction preload latches to any
desired configuration without disturbing the work in progress. After any write to the configuration registers,
LOAD must be brought high for one cycle, and can then be brought and left low if so desired.
RESET - Global Reset
Bringing synchronous control RESET LOW forces all state machines and read and write pointers to 0 and
holds them there until it is released HIGH. It also forces the configuration registers to their default states,
if and only if LOAD is also LOW. The user may then modify the control registers as necessary. Bringing
RESET LOW while holding LOAD HIGH will reset the state machines and pointers, but will not change either
the preload or the working latches.
AOE - Output Enable A
When AOE is LOW, AOUT11-0 is enabled for output. When AOE is HIGH, AOUT11-0 is placed in a highimpedance state. In 10-bit modes, AOUT1-0 are unconditionally tristated. In 8-bit modes, AOUT3-0 are
tristated. The flag outputs are not affected by AOE.
BOE - Output Enable B
In any dual-channel mode, when BOE is LOW, BOUT11-0 is enabled for output. When BOE is HIGH, or in
any single-channel mode, BOUT11-0 is placed in a high-impedance state. In 10-bit modes, BOUT1-0 are
tristated. In 8-bit modes, BOUT3-0 are tristated. The flag outputs are not affected by BOE.
CSB - Chip Enable
When LOW, CSB enables writing to the LF3312 with the parallel micrprocessor interface.
WEB - Parallel Microprocessor Interface Write Enable
When LOW, WE enables writing to the LF3312’s Instruction Registers with the parallel micrprocessor
interface.
REB - Parallel Microprocessor Interface Read Enable
When LOW, RE enables reading from the LF3312’s Instruction Registers with the parallel micrprocessor
interface.
LOGIC Devices Incorporated
15
Video Imaging Product
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Detailed Signal Definitions
Data Outputs
AOUT11-0 - Data Output A
AOUT11-0 is the 12-bit registered data output port. AOUT[11] is always the MSB. In 10-bit mode,
bits 1 and 0 are tristated. In 8-bit mode, bits 3-0 are tristated. All active bits are updated on each
rising edge of RCLK when AREN is LOW.
BOUT11-0 - Data Output B
In OPMODES 4-7, BOUT11-0 is the 12-bit registered data output port. BOUT[11] is always the MSB. In
10-bit mode, bits 1 and 0 are tristated. In 8-bit mode, bits 3-0 are tristated. All active bits are updated
on each rising edge of RCLK when BREN is LOW. In OPMODES 0-3 refer to the input description
of BOUT11-0.
Flag Outputs
APF / BPF - Programmable Almost Full Flag A & B
APF / BPF goes HIGH (active) when the write pointer is more than
(MAX_depth - (MAX_depth x TH)) locations ahead of the read pointer. TH is a threshold value stored
in the Register 9 [2:0]. APF is updated on the rising edge of AWCLK. In Dual-Channel mode, BPF is
updated on the rising edge of BWCLK. TRS bits from AIN or AOUT can be mapped to APF (Register
B[3:0]). In Dual-Channel mode, TRS bits from BIN or BOUT can be mapped to BPF (Register B[7:4]).
APE / BPE - Programmable Almost Empty Flag A & B
APE / BPE goes HIGH (active) when the write pointer is less than or equal to
(MAX_depth - (MAX_depth x TL)) locations ahead of the read pointer. TL is a threshold value stored
in the Register 9 [2:0]. APE is updated on the rising edge of RCLK. In Dual-Channel mode, BPF is
updated on the rising edge of RCLK. TRS bits from AIN or AOUT can be mapped to APE (Register
B[3:0]). In Dual-Channel mode, TRS bits from BIN or BOUT can be mapped to BPE (Register B[7:4]).
ACOLLIDE - Memory Read/Write Pointer Collision Flag A
This flag goes high whenever the read and write addresses to the memory core (single-channel
modes) or its “A” channel (dual-channel modes) coincide. By monitoring the partial full/empty
flags, the user can ascertain the direction of approach, i.e., read pointer catching up with write
(FIFO empty) or write pointer catching up with read (FIFO full). TRS bits from AIN or AOUT
can be mapped to ACOLLIDE (Register B[3:0]).
BCOLLIDE - Memory Read/Write Pointer Collision Flag B
In dual-channel modes, this flag goes high whenever the read and write addresses to the Channel B
memory core coincide. By monitoring the partial full/empty flags, the user can ascertain the direction
of approach, i.e., read pointer catching up with write (FIFO empty) or write pointer catching up with read
(FIFO full). TRS bits from BIN or BOUT can be mapped to BCOLLIDE (Register B[7:4]).
JTAG
TDI - JTAG input data
TDI is the input data pin when using JTAG.
TDO - JTAG output data
TDO is the output data pin when using JTAG.
TRSTB - JTAG reset
TRSTB is used to reset all the registers and state machine fount the the JTAG module.
Video Imaging Product
LOGIC Devices Incorporated
16
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
TMS - JTAG Tap controller input
TMS controls the state of the tap controller.
TCK - JTAG clock
TCK is the used supplied clock of JTAG. It controls the flow of data and latches input data on the rising edge.
Configuration Register Map
The various 8-bit control registers may be pre-programmed with either the parallel microprocessor port
(PROGRAM=1), or through the serial microprocessor interface bus(PROGRAM=0). Changes in preprogramming begin to affect the data path when LOAD is brought LOW. In each instance, the value in
parens () is the default state following assertion of RESET while LOAD = 0.
Instruction Register 0 (dflt = 00000000)
3:0 = ROW_LENGTH[11:8]
(0000: 24-bit linear map; see reg 7)
Instruction Register 1 (dflt = 00000000)
7:0 = ROW_LENGTH[7:0]
(00000000: 24-bit linear map; see reg 6)
Instruction Register 2 (dflt = 00000000)
7:0 = ALATENCY[23:16]
(00000000: default = 0; see reg 9, a)
Instruction Register 3 (dflt = 00000000)
7:0 = ALATENCY[15:8]
(00000000: default = 0; see reg 8, a)
Instruction Register 4 (dflt = 00000000)
7:0 = ALATENCY[7:0]
(00000000: default = 0; see reg 8, 9)
Instruction Register 5 (dflt = 00000000)
7:0 = BLATENCY[23:16]
(00000000)
Instruction Register 6 (dflt = 00000000)
7:0 = BLATENCY[15:8]
(00000000)
Instruction Register 7 (dflt = 00000000)
7:0 = BLATENCY[7:0]
(00000000)
Video Imaging Product
LOGIC Devices Incorporated
17
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Configuration Register Map
Instruction Register 8 (dflt = 10_00_0_111)
7:6 = WIDTH[1:0]
(10: 10 bits)
5:4 = Reserved
(Make equal to 00)
3
(Make equal to 0)
= MARK_ACTIVE_RESET
2:0 = OPMODE
(111: Two-Channel Asynchronous FIFO)
Instruction Register 9 (dflt = 00_000_000)
7:6 = TRS_SYNC[1:0]
(00: ignore embedded TRS)
5
= B_FLD
(0: frame sync - use falling F-bit from TRS)
4
= A_FLD
(0: frame sync - use falling F-bit from TRS)
3
= MARK_SEL
(0: use marked address - not user defined address)
2:0 = FLAG_SET
(000: trigger empty, full on 1/80, 79/80)
Instruction Register A (dflt = 00000000)
7
= BSET_catch
(0: setting B pointer does not MARK its new value)
6
= ASET_catch
(0: setting A pointer does not MARK its new value)
5
= RSET_b_sel
(0: RSET is falling edge triggered)
4
= RCLR_b_sel
(0: RCLR is falling edge triggered)
3
= BSET_b_sel
(0: BSET is falling edge triggered)
2
= BCLR_b_sel
(0: BCLR is falling edge triggered)
1
= ASET_b_sel
(0: ASET is falling edge triggered)
0
= ACLR_b_sel
(0: ACLR is falling edge triggered)
Instruction Register B (dflt = 00_00_00_00)
7:4 = BFLAG_CTL
(00: BPE, BPF are part-empty, -full)
3:0 = AFLAG_CTL
(00: APE, APF are part-empty, -full)
Instruction Register C (dflt = 0000_0000)
LOGIC Devices Incorporated
7:4 = BASE_ADDR
(0000: lowest-address chip in cascade sequence)
3:0 = CASCADE
(0000: single chip - no cascade of multiple chips)
18
Video Imaging Product
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Configuration Register Definitions
Register 0[3:0], Register 1[7:0] = ROW_LENGTH[11:0] - for Cartesian-to-linear address map in
Single-channel modes
This control governs the remapping of Cartesian coordinates arriving on BIN (horizontal/column component) and BOUT (vertical/row component) into a linear address, for use by the chip’s internal address
generator. Setting ROW_LENGTH to 0 causes the incoming address to be interpreted directly as a
linear address (or equivalently, a Cartesian address with 4095 pixels per line), with the 12 bits of BOUT
concatenated with the lesser significant 12 bits of BIN.
Register 2[7:0], Register 3[7:0], Register 4[7:0] = ALATENCY[23:0] - Shift Register
Latency (Channel A) or 24bit ‘Jump’ Address
In single-channel synchronous shift register mode (OPMODE = 0), ALATENCY determines the effective
shift register depth, i.e., such that the chip’s input-to-out latency = TBD + (ALATENCY clock cycles). In
dual-channel shift register modes, this register sets the Channel A delay. For OPMODE = 0, 4 or 5, a
falling edge on pin AMARK registers the current value of the write pointer and starts a countdown timer,
which forces the read pointer to this registered value ALATENCY clock cycles later. The maximum
delay that ALAT can be made equal to is 224-2 clock cycles.
In addition to this function, in all single-channel OPMODES, bringing ASET LOW forces/jumps the
memory write pointer to the address defined by ALATENCY (when BSET is LOW). Thus, when
ALATENCY is used to establish a time delay, it is interpreted as an ordinary unsigned binary number.
In contrast, when it is used to override an address pointer, ALATENCY defines an address. When
ROW_LENGTH is a non-zero value, ALATENCY[11:0] is equal to the 12-bit X-coordinate (Horizontal)
and ALATENCY[23:12] is considered the Y-coordinate (Vertical) in a Cartesian Coordinate system.
When ROW_LENGTH is 0, ALATENCY[23:0] is considered to be a linear address in the memory space.
By changing the ROW_LENGTH, the X-coordinate can be from 0 to (ROW_LENGTH-1) to make up the
Cartesian plane. For example, if ROW_LENGTH = 16, the X-coordinate or ALATENCY[11:0] can be
from 0 to 15 in the Cartesian space.
Register 5[7:0], Register 6[7:0], Register 7[7:0] = BLATENCY[23:0] - shift register depth for
(Channel B) or 24bit ‘Jump’ Address
In dual-channel synchronous shift register mode (OPMODE = 4), BLATENCY determines the effective
Channel B shift register depth, i.e., such that the chip’s input-to-out latency = TBD + (BLATENCY
clock cycles).
in single-channel OPMODES, bringing RSET LOW forces/jumps the read pointer to the address defined
by BLATENCY. In dual-channel modes, BLATENCY impacts channel B exactly as ALATENCY impacts
channel A. Total Channel B data latency = TBD + (BLATENCY clock cycles).
Video Imaging Product
LOGIC Devices Incorporated
19
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Configuration Register Definitions
Register 8[7:6] = WIDTH[1:0] - data word size at input/output ports
0x
8 bits
[11:4]
xOUT[3:0] tristated
10
10 bits
[11:2] (dflt)
xOUT[1:0] tristated
11
12 bits
[11:0]
Register 8[5:4] = Reserved
Register 8[3] = MARK_ACTIVE_RSET
0
ignores the internal RSET that occurs following the MARK
1
obeys the internal RSET according to the MARK
Register 8[2:0] = OPMODE[2:0] - operating mode
LOGIC Devices Incorporated
000
1 channel
Synchronous Shift Register
001
1 channel
Random Access
010
-------
RESERVED
011
1 channel
Asynchronous FIFO
100
2 channel
Synchronous Shift Register
101
2 channel
FIFO, B slaved to A
110
2 channel
FIFO, A slaved to B
111
2 channel
Asynchronous FIFO (default)
20
Video Imaging Product
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Configuration Register Definitions
Register 9[7:6] = TRS_SYNC[1:0] - response to embedded TRS EAV (a)
00
disable TRS sync detection (dflt)
01
F-bit of embedded TRS EAV marks current write pointer.
10
F-bit of embedded TRS EAV sets current write pointer to value
set by BOUT/BIN or ALAT (1-chnl.modes) or ALAT & BLAT (2-chnl.
modes, respectively).
11
F-bit of embedded TRS EAV clears current write pointer.
- If B_FLD = 0 (frame-based sync), action is on each B-channel
EAV with F = 0 for which the preceding EAV had F = 1.
- If B_FLD = 1 (field-based sync), action is on each B-chan EAV
whose F differs from that of the preceding EAV. A_FLD affects
the tA-channel operation in the same fashion.
Register 9[5] = B_FLD frame/field sync select, chnl B
0
use only falling F-bit in EAV; ignore rising (dflt)
1
use both rising and falling F-bit in EAV
Register 9[4] = A_FLD frame/field sync select, chnl A
0
use only falling F-bit in EAV; ignore rising (dflt)
1
use both rising and falling F-bit in EAV
Register 9[3] MARK_SEL - This signal is used in combination with pin BCLR to determine to
effect of bringing RSET low on the read pointer(s). When RSET goes to 0:
0
force read pointer(s) to marked address(es) (dflt)
1
force read pointer(s) as shown in following table:
OPMODE BCLR
Read Pointer Equals:
0-3
1
BIN/BOUT address
0-3
0
BLAT address
4-7
x
Ch. A=ALAT, Ch. B=BLAT
Video Imaging Product
LOGIC Devices Incorporated
21
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Configuration Register Definitions
Register 9[2:0] = FLAG_SET[2:0] - sets fractional “Fullness” and “Emptiness” Thresholds for Programmable Empty/Full Flags.
Full flag goes HIGH when the memory is more than “TH” full. Empty flag goes
HIGH when the memory is less than or equal to “TL” full.
000
TH = 79/81 (dflt)
TL = 1/81 (dflt)
001
TH = 78/81
TL = 2/81
010
TH = 77/81
TL = 3/81
011
TH = 76/81
TL = 4/81
100
TH = 75/81
TL = 5/81
101
TH = 74/81
TL = 6/81
110
TH = 73/81
TL = 7/81
111
TH = 72/81
TL = 8/81
Register A[7] = BSET_catch - (OPMODES 4-7 only)
0:
setting write pointer B does not mark its new value (dflt)
1:
setting write pointer B automatically marks its new value
Register A[6] = ASET_catch - (all OPMODES) logic same as above for BSET_catch
Register A[5:0] Control action.
LOGIC Devices Incorporated
Rb[5]
RSET_b_sel
Rb[4]
RCLR_b_sel
Rb[3]
BSET_b_sel
Rb[2]
BCLR_b_sel
Rb[1]
ASET_b_sel
Rb[0]
ACLR_b_sel
if 0:
Each falling edge on the corresponding control pin overrides a
memory address counter for exactly one clock cycle, after which
normal memory address incrementing immediately resumes. (dflt)
if 1:
The corresponding pin continuously overrides the memory address
counter as long as it is held LOW. Memory address incrementing
resumes when the pin is returned HIGH.
22
Video Imaging Product
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Configuration Register Definitions
Register B[7:4] = BFLAG_CTL[3:0] for pins BPE and BPF * (See below for legend)
BFLAG_CTL
BPE
BPF
BCOLLIDE
0000
B empty (R)
B full (W)
BCOLLIDE (R)
0001
RB=MB (R)
RA=MA (R)
BCOLLIDE (R)
0010
BIN f (W)
BIN v (W)
BIN h (W)
0011
BOUT f (R)
BOUT v (R)
BOUT h (R)
0100
BIN f (W)
BIN v (W)
BCOLLIDE (R)
0101
BOUT f (R)
BOUT v (R)
BCOLLIDE (R)
0110
BIN f (W)
BIN h (W)
BCOLLIDE (R)
0111
BOUT f (R)
BOUT h (R)
BCOLLIDE (R)
1000
BIN v (W)
BIN h (W)
BCOLLIDE (R)
1001
BOUT v (R)
BOUT h (R)
BCOLLIDE (R)
*Each flag is updated on the rising edge of its associated clock: BWCLK (W) or RCLK (R)
AIN f, v, h are the TRS bits embedded in the incoming A channel TRS signals.
AOUT f, v, h are the TRS bits embedded in the emerging A channel TRS signals.
BIN f, v, h and BOUT f, v, h are the analogous B channel values.
RA(RB) is the read address pointer value for channel A(B).
MA(MB) is the ‘marked’ address pointer value for channel A(B).
Register B[3:0] AFLAG_CTL[3:0] for pins APE and APF *
AFLAG_CTL
APE
APF
ACOLLIDE
0000
A empty (R)
A full (W)
ACOLLIDE (R)
0001
RB=MB (R)
RA=MA (R)
ACOLLIDE (R)
0010
AIN f (W)
AIN v (W)
AIN h (W)
0011
AOUT f (R)
AOUT v (R)
AOUT h (R)
0100
AIN f (W)
AIN v (W)
ACOLLIDE (R)
0101
AOUT f (R)
AOUT v (R)
ACOLLIDE (R)
0110
AIN f (W)
AIN h (W)
ACOLLIDE (R)
0111
AOUT f (R)
AOUT h (R)
ACOLLIDE (R)
1000
AIN v (W)
AIN h (W)
ACOLLIDE (R)
1001
AOUT v (R)
AOUT h (R)
ACOLLIDE (R)
*Each flag is updated on the rising edge of its associated clock: AWCLK (W) or RCLK (R)
Video Imaging Product
LOGIC Devices Incorporated
23
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Configuration Register Definitions
Register C[7:4] = BASE_ADDR[3:0] - position of chip in cascade series; 0000 = lowest;
BASE_ADDR[3:0] must not exceed CASCADE[3:0]
Register C[3:0] = CASCADE[3:0] - number of chips in a system with concatenated
address spaces.
0000:
0001:
single chip operation; (dflt) sequential R, W addresses, modulo 103,680
two chip cascade; sequential R, W addresses, modulo 207,360
...
1111:
...
sixteen chip cascade; (a) sequential R, W addresses, modulo 1,658,880
(a) Note limits regarding the number of possible chips, related to WIDTH control:
8bit data: 10 or less LF3312s (WIDTH = 0x)
10bit data: 13 or less LF3312s (WIDTH = 10)
12bit data: 16 or less LF3312s (WIDTH = 11)
Configuration Registers For Testing
Addresses D hex and above are for test purposes only.
LOGIC Devices Incorporated
24
Video Imaging Product
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
MAXIMUM RATINGS Above which useful life may be impaired (Notes 1, 2, 3, 8)
Storage temperature
–65°C to +150°C
VCCINT , Internal supply voltage with respect to ground
–0.5V to + 2.0V
VCCO, Output drivers supply voltage with respect to ground
–0.5V to + 4.0V
Signal applied to high impedance output
–0.5V to + 3.3V
Output current into low outputs
25 mA
Latchup current
> 400 mA
OPERATING CONDITIONS To meet specified electrical and switching characteristics
Characteristic
Mode
Temperature Range
Supply Voltage
VCCINT
Commerical
0°C to +70°C
1.71V < Vcc < 1.89V
VCCO
Commerical
0°C to +70°C
3.00V < Vcc < 3.60V
ELECTRICAL CHARACTERISTICS Over Operating Conditions (Note 4)
Symbol
Parameter
Test Condition
VOH
Output High Voltage
VCC = Min., IOH MAX = -4 mA
VOL
Output Low Voltage
VCC = Min., IOL MAX = 4 mA
VIH
Input High Voltage
VIL
Input Low Voltage
(Note 3)
IIx
Input Current
IIx
Min
Typ
Max
Unit
V
2.4
0.4
V
V
2.0
0.8
V
With Internal Pull-up - JTAG & I2C pins
+20
µA
Input Current
All other pins
±10
µA
IOZ
Output Leakage Current
Ground < VOUT < VCC (Note 12)
±10
µA
ICC1
VCCint Current, Dynamic
f=55MHz, VCCint =1.9V (Note 7)
48
mA
ICC2
VCCint Current, Quiescent
VCCint =1.9V (Note 7)
550
µA
ICC3
VCCo Current, Dynamic
f=74MHz, VCCo =3.6V (Note 6)
12
mA
ICC4
VCCo Current, Quiescent
VCCo =3.6V
60
mA
CIN
Input Capacitance
TA = 25°C, f = 1 MHz
7
pF
COUT
Output Capacitance
TA = 25°C, f = 1 MHz
7
pF
LOGIC Devices Incorporated
25
Video Imaging Product
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Switching Characteristics
Commercial Operating Range (0°C to +70°C) Notes 9, 10 (ns)
LF3312BGC
Symbol
Parameter
Min
tCYC1
Cycle Time 1 (AWCLK,BWCLK,RCLK) - FIFO / Sh. Reg Modes
13.4
tCYC2
tPWH
tPWL
tDS
tDH
tWES
Cycle Time 2 (AWCLK,BWCLK,RCLK) - Full-time Random Access
18
Clock Pulse Width High (AWCLK,BWCLK,RCLK)
5
Clock Pulse Width Low (AWCLK,BWCLK,RCLK)
5
Setup Time, Data Inputs (AIN,BIN)
5
Hold Time, Data Inputs (AIN,BIN)
1
Write Enable Setup Time (AWEN,BWEN)
5
tWEH
tRES
tREH
tLDS
tLDH
tRWS
tRWH
tD
tF
tDIS
tENA
tCSU
tCHD
tCSPW
tCDLY
tCZ
Write Enable Hold Time (AWEN,BWEN)
1
Read Enable Setup Time (AREN,BREN)
5
Read Enable Hold Time (AREN,BREN)
1
Load Setup Time
5
Load Hold Time
1
R/W Set/Clr Setup Time (ACLR,BCLR,ASET,BSET,RSET,RCLR)
5
R/W Set/Clr Hold Time (ACLR,BCLR,ASET,BSET,RSET,RCLR)
1
Max
Access Time
7
Write Clock to Programmable Flags (A/BPE,A/BPF,A/BOLLIDE)
7
Tri-state Output Disable Delay
10
Tri-state Output Enable Delay
10
Parallel Interface Control Setup Time for Reads/Writes
5
Parallel Interface Control Hold Time for Reads/Writes
1
Parallel Interface Control Strobe pulse width
20
Parallel Interface Control Output Delay
8
Parallel Interface Control Tristate delay
10
Min
Max
Video Imaging Product
LOGIC Devices Incorporated
26
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Write Cycle Timing - Write Enable
AWCLK
BWCLK
tWES
tPWH
tPWL
tCYC1
tCYC2
AWEN
BWEN
tDS
AIN11–0
BIN11–0
tWEH
tDH
(n)
(n+1)
(n+3)
(n+5)
(n+4)
AIEN=BIEN= LOW
NOTE: AWEN/BWEN must be brought LOW 2 rising edges of AWCLK/BWCLK prior to latching valid data on AIN or BIN
Write Cycle Timing - Write Masking
AWCLK
BWCLK
tWES
tPWH
tPWL
tCYC1
tCYC2
AIEN
BIEN
tDS
AIN11–0
BIN11–0
tWEH
tDH
(n)
(n+1)
(n+3)
data not
written
(n+5)
(n+4)
data not
written
(n+6)
(n+7)
AWEN=BWEN= LOW
NOTE: bringing AIEN/BIEN HIGH disables data on AIN/BIN from being written into memory, yet it does not disable the Write pointer from incrementing
NOTE: AIEN/BIEN must be brought HIGH 2 rising edges of AWCLK/BWCLK prior to masking input data on AIN or BIN
Read Cycle Timing
RCLK
tRES
tPWH
tPWL
tCYC1
tCYC2
AREN
BREN
tREH
tD
tD
AOUT11–0
BOUT11–0
(n–2)
APE
BPE
COLLIDE
(n–1)
(n+1)
(n)
tF
(n+2)
(n+3)
tF
AOE = BOE = LOW
NOTE: AREN/BREN should be brought LOW 2 rising edges of RCLK prior to expecting valid data on AOUT
LOGIC Devices Incorporated
27
Video Imaging Product
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Write Reset Timing
1
2
3
4
5
AWCLK
BWCLK
tRWH
tRWS
ACLR
BCLR
tRWS
tRWH
ASET
BSET
tDS
AIN11–0
BIN11–0
(n)
(n+1)
tDH
(0)
(2)
(1)
(A)
(A+1)
AWEN=BWEN= LOW
ACLR and ASET both programmed to be falling edge sensitive
* Rising Edge 1: Clears Write Pointer and latches data on AIN to be written in address 0
* Rising Edge 4: Sets Write Pointer to Address A (based on ALATENCY) and latches data on AIN to be written in address A
Read Reset Timing
1
2
8
9
10
RCLK
....
tRWS
ACLR
BCLR
AOUT11–0
BOUT11–0
(n)
(n+1)
tD
(n+2)
(n+8)
(1)
(0)
AREN=BREN= LOW
NOTE: ACLR/BCLR programmed as being falling edge sensitive
It takes 9 AREN-enabled rising edges of RCLK (including the edge that latches a LOW on ACLR) to pass the contents of address 0 to the AOUT port.
Random Access Read Pointer ‘Jump’ Timing
1
13
14
RCLK
BOUT11–0
A23–12
tDS
BIN11–0
tDH
A11–0
RSET
tD
tD
AOUT11–0
AOE = LOW
(n–2)
BOE= HIGH
(n-1)
AREN=BREN= LOW
(n)
(n+13)
BSET= LOW
BCLR= HIGH
(A)
OPMODE[2:0]=001
(A+1)
MARK_SEL (Register 9[3]) =1
NOTE: RSET programmed to be falling edge sensitive
NOTE: It takes 14 rising edges of RCLK upon setting/jumping the Read pointer
(to the 24bit Address "A" on BIN/BOUT) for the contents of location A to be dumped onto AOUT
Video Imaging Product
LOGIC Devices Incorporated
28
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Random Access Write Pointer ‘Jump’ Timing
1
AWCLK
BWCLK
BOUT11–0
A23–12
tDS
BIN11–0
tDH
A11–0
tRWS
ASET
AIN11–0
(n)
AWEN=BWEN= LOW
(n+1)
(A)
BSET= HIGH
(A+1)
(A+2)
(A+3)
(A+4)
OPMODE[2:0]=001
NOTE: ASET programmed to be falling edge sensitive
NOTE: Rising edge of AWCLK/BWCLK labeled "1" writes data on AIN to 24bit Address "A"
Output Enable and Disable
AOE
BOE
tDIS
tENA
AOUT11–0
BOUT11–0
HIGH IMPEDANCE
Jumping/Setting Pointers based on Configuration Register Address after Remapping Process
1
2
3
4
5
6
7
AWCLK
BWCLK
tRWH
tRWH
AWEN
LOAD
1
2
tRWS
ASET
BSET
RSET
tRWH
3
tRWS
tRWH
4
5
ASET, BSET, and RSET programmed to be level sensitive
1 AWEN
2 The
is LOW for 3 rising edges of AWCLK prior to LOAD transition. It stays LOW for the minimum required 5 rising edges after the LOAD transition.
configuration registers are programmed while LOAD is LOW. The LOAD transition triggers the address remap process.
3 ASET
can be brought LOW (edge "3") 3 rising edges of AWCLK after the LOAD transition, jumping the write pointer to the address programmed into the ALATENCY register.
4
BSET can be brought LOW (edge "7") 7 rising edges of BWCLK after the LOAD transition, jumping the CH. A write pointer to the address programmed into the BLATENCY register (dual-channel mode).
5RSET
can be brought LOW (edge "7") 7 rising edges of RCLK after the LOAD transition, jumping the read pointer to the address programmed into the
ALATENCY register (dual-channel) or BLATENCY register (single-channel).
LOGIC Devices Incorporated
29
Video Imaging Product
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Notes
1. Maximum Ratings indicate stress specifications only. Functional operation of these products
at values beyond those indicated in the Operating Conditions table is not implied. Exposure to
maximum rating conditions for extended periods may affect reliability.
2. The products described by this specification include internal circuitry designed to protect the chip
from damaging substrate injection currents and accumulations of static charge. Nevertheless,
conventional precautions should be observed during storage, handling, and use of these circuits
in order to avoid exposure to excessive electrical stress values.
3. This device provides hard clamping of transient undershoot. Input levels below ground will be
clamped beginning at –0.6 V. The device can withstand operation with inputs or outputs in the
range of –0.5 V to +5.5 V. Device operation will not be adversely affected, however, input current
levels may be in excess of 100 mA.
4. Actual test conditions may vary from those designated but operation is guaranteed as specified.
5. I/O Ring supply current for a given application can be approximated by:
where
N
C
V
F
NCV2 F
2
= total number of device outputs
= capacitive load per output
= supply voltage
= clock frequency
6. Tested in single-channel mode with 14 output pins driving 10pF loads, while toggling at an average of 30% of the 74MHz clock rate. The 10pF load is estimate of trace and downstream pin
capacitance.
7. Operating condition assumed to be most demanding reading/writing memory scenario .
8. These parameters are guaranteed but not 100% tested.
9. AC specifications are tested with input transition times less than 3 ns, output reference levels
of 1.5 V (except tdis test), and input levels of nominally 0 to 3.0V. Output loading may be a
resistive divider which provides for specified IOH and IOL at an output voltage of VOH min and
VOL max respectively. Alternatively, a diode bridge with upper and lower current sources of IOH
and IOL respectively, and a balancing voltage of 1.5 V may be used. Parasitic capacitance is 30
pF minimum, and may be distributed.
This device has high-speed outputs capable of large instantaneous current change pulses and
fast turn-on/turn-off times. As a result, care must be exercised in the testing of this device. The
following measures are recommended:
a. A 0.1 µF ceramic capacitor should be installed between VCC and Ground leads as close to
the device as possible. Similar capacitors should be installed between device VCC and the tester
common, and device ground and tester common.
b. Ground and VCC supply planes must be brought directly to the device leads.
Video Imaging Product
LOGIC Devices Incorporated
30
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Notes
c. Input voltages on a test fixture should be adjusted to compensate for inductive ground and VCC
noise to maintain required input levels relative to the device ground pin.
10. Each parameter is shown as a minimum or maximum value. Input requirements are specified
from the point of view of the external system driving the chip. Setup time, for example, is specified
as a minimum since the external system must supply at least that much time to meet the worstcase requirements of all parts. Responses from the internal circuitry are specified from the point of
view of the device. Output delay, for example, is specified as a maximum since worst-case operation of any device always provides data within that time.
11. For the tena test, the transition is measured to the 1.5 V crossing point with datasheet loads.
For the tdis test, the transition is measured to the ±200mV level from the measured steady-state
output voltage with ±10mA loads. The balancing voltage, Vth, is set at 3.0 V for Z-to-0 and 0-to-Z
tests, and set at 0 V for Z-to-1 and 1-to-Z tests.
12. These parameters are only tested at the high temperature extreme, which is the worst case
FIGURE B. THRESHOLD LEVELS
FIGURE A. OUTPUT LOADING CIRCUIT
tENA
OE
S1
DUT
IOL
Z
0
tDIS
1.5 V
1.5 V
1.5 V
3.0V Vth
VOL*
0.2 V
VTH
CL
IOH
Z
1
1.5 V
VOH*
0.2 V
0
Z
1
Z
0V Vth
VOL* Measured VOL with IOH = –10mA and IOL = 10mA
VOH* Measured VOH with IOH = –10mA and IOL = 10mA
LOGIC Devices Incorporated
31
Video Imaging Product
August 18, 2005 LDS.3312 M
LF3312
12-Mbit Frame Buffer / FIFO
DEVICES INCORPORATED
Preliminary Datasheet
Package and Ordering Information
1.00 REF
BALL PAD CORNER
14
13
12
11
10
9
8
7
6
5
4
3
2
1
AOE_b
AREN_b
BREN_b
PADDR5
PADDR3
PADDR0
PROGRAM
WEB
CHIP_ID5
CHIP_ID2
BIEN_b
BWEN_b
RESET_b
GND
AOUT11
VCCO
RSET_b
RCLR_b
PADDR4
PADDR1
CSB
REB
CHIP_ID4
CHIP_ID1
AIEN_b
AWEN_b
VCCINT
AIN11
AOUT10
VCCO
GND
VCCINT
PADDR2
LOAD_b
VCCINT
CHIP_ID6
CHIP_ID3
VCCINT
VCCINT
AIN8
AIN9
AIN10
AOUT8
AOUT9
VCCO
GND
GND
VCCINT
GND
VCCINT
GND
CHIP_ID0
GND
VCCINT
VCCO
AIN7
AOUT5
VCCO
AOUT7
GND
AOUT6
GND
GND
GND
GND
AIN4
VCCO
AIN5
AOUT3
AOUT4
VCCO
GND
AOUT2
AIN6
AIN3
VCCINT
AIN1
AIN2
AOUT0
RCLK
AOUT1
GND
GND
AIN0
VCCO
AWCLK
BOUT0
VCCO
BOUT1
GND
GND
VCCINT
BIN0
BWCLK
BOUT3
BOUT2
VCCO
GND
GND
GND
GND
BIN1
VCCO
BIN
BOUT5
BOUT4
BOUT6
BOUT7
GND
GND
GND
GND
BIN3
GND
BIN5
BIN4
BOUT8
BOUT9
VCCO
VCCO
ACLR_b
GND
GND
GND
GND
PDATA2
BIN6
BIN8
VCCO
BIN7
BOUT11
BOUT10
VCCO
VCCO
PDATA7
VCCO
PDATA4
VCCO
TCK
BIN11
BIN9
BIN10
BOE_b
BPE
ACOLLIDE
BSET_b
VCCO
VCCO
SDA
PDATA6
VCCO
PDATA0
TMS
TDI
GND
VCCINT
APE
APF
BPF
ASET_b
AMARK_b
BCLR_b
SCL
PDATA5
PDATA3
PDATA1
TRST_b
TDO
VCCO
GND
A
B
C
D
E
F
G
BOTTOM
VIEW
H
J
1.00 REF
K
L
M
BCOLLIDE BMARK_b
N
P
I/O VCC Pin
Core VCC Pin
1.00 REF
Signal Pin
GND Pin
1.00 REF
172 Ball - Low Profile Ball Grid Array (LBGA)
0°C to 70°C--Commercial Screening
Speed
_
LF3312BGC
Video Imaging Product
LOGIC Devices Incorporated
32
August 18, 2005 LDS.3312 M