T-1 (3mm) SOLID STATE LAMP Part Number: WP710A10GD5V Green ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z Low power consumption. z The Green source color devices are made with Gallium z Popular T-1 diameter package. Phosphide Green Light Emitting Diode. z Electrostatic discharge and power surge could damage z General purpose leads. the LEDs. z Reliable and rugged. z Long life - solid state reliability. z It is recommended to use a wrist band or antielectrostatic glove when handling the LEDs. z Available on tape and reel. z All devices, equipments and machineries must be z 5V internal resistor. electrically grounded. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SPEC NO: DSAL0503 REV NO: V.5B DATE: JAN/22/2015 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101029206 Selection Guide Part No. Dice WP710A10GD5V Lens Type Green (GaP) Viewing Angle [1] Iv (mcd) [2] V= 5V Min. Typ. 2θ1/2 12 25 40° Green Diffused Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 565 nm VF=5V Green 568 nm VF=5V Spectral Line Half-width Green 30 nm VF=5V IF Forward Current Green 11.5 17.5 mA VF=5V IR Reverse Current Green 10 uA VR = 5V Notes: 1. Wavelength: +/-1nm. 2. Wavelength value is traceable to the CIE127-2007 compliant national standards. 3. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Green Units Power dissipation 85 mW Forward Voltage 6 V Reverse Voltage 5 V Operating Temperature -40°C To +70°C Storage Temperature -40°C To +85°C Lead Solder Temperature [1] 260°C For 3 Seconds Lead Solder Temperature [2] 260°C For 5 Seconds Notes: 1. 2mm below package base. 2. 5mm below package base. SPEC NO: DSAL0503 REV NO: V.5B DATE: JAN/22/2015 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101029206 Green WP710A10GD5V SPEC NO: DSAL0503 REV NO: V.5B DATE: JAN/22/2015 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101029206 PACKING & LABEL SPECIFICATIONS WP710A10GD5V Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAL0503 REV NO: V.5B DATE: JAN/22/2015 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101029206 SPEC NO: DSAL0503 REV NO: V.5B DATE: JAN/22/2015 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101029206 SPEC NO: DSAL0503 REV NO: V.5B DATE: JAN/22/2015 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101029206