T-1 (3mm) BLINKING LED LAMP Features Descriptions

T-1 (3mm) BLINKING LED LAMP
Part Number: WP36BHD
Bright Red
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Features
Descriptions
z T-1 package with rectangular base.
z The Bright Red source color devices are made with Gal
lium Phosphide Red Light Emitting Diode.
z With built-in blinking IC.
z Operation voltage from 3.5V to 14V.
z Blinking frequency from 3.0Hz to 1.5Hz.
z Electrostatic discharge and power surge could damage
the LEDs.
z It is recommended to use a wrist band or anti-
z RoHS compliant.
electrostatic glove when handling the LEDs.
z All devices, equipments and machineries must be
electrically grounded.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
SPEC NO: DSAE8732
REV NO: V.7B
DATE: JAN/26/2015
PAGE: 1 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1101003773
Selection Guide
Part No.
Dice
WP36BHD
Bright Red (GaP)
Red Diffused
Viewing
Angle [1]
Iv (mcd)
V= 9V
Lens Type
Min.
Typ.
2θ1/2
0.6
1.8
60°
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Min.
Typ.
λpeak
Peak Wavelength
Bright Red
700
nm
λD
Dominant Wavelength
Bright Red
635
nm
Δλ1/2
Spectral Line Half-width
Bright Red
45
nm
IF
Forward Current
Bright Red
22
mA
Min:VF=3.5V
Typ:VF=5V
ISON
Supply Current
Bright Red
8
mA
VF=3.5V
ISON
Supply Current
Bright Red
44
mA
VF=14V
f
Blink Frequency
Bright Red
Hz
VF=3.5V~14V
8
Max.
1.5
3
Units
Test Conditions
Notes:
1.Wavelength value is traceable to the CIE127-2007 compliant national standards.
2.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
Bright Red
Units
Power dissipation
310
mW
Forward Voltage
14
V
Reverse Voltage
0.5
V
Operating Temperature
-40°C To +70°C
Storage Temperature
-40°C To +85°C
Lead Solder Temperature [1]
260°C For 3 Seconds
Lead Solder Temperature [2]
260°C For 5 Seconds
Notes:
1. 2mm below package base.
2. 5mm below package base.
SPEC NO: DSAE8732
REV NO: V.7B
DATE: JAN/26/2015
PAGE: 2 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1101003773
Bright Red
WP36BHD
SPEC NO: DSAE8732
REV NO: V.7B
DATE: JAN/26/2015
PAGE: 3 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1101003773
PACKING & LABEL SPECIFICATIONS
WP36BHD
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAE8732
REV NO: V.7B
DATE: JAN/26/2015
PAGE: 4 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1101003773
SPEC NO: DSAE8732
REV NO: V.7B
DATE: JAN/26/2015
PAGE: 5 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1101003773
SPEC NO: DSAE8732
REV NO: V.7B
DATE: JAN/26/2015
PAGE: 6 OF 6
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: P.Cheng
ERP: 1101003773