T-1 3/4(5mm) BLINKING LED LAMP Part Number: WP56BHD Bright Red ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z T-1 3/4 package. z The Bright Red source color devices are made with Gal lium Phosphide Red Light Emitting Diode. z With built-in blinking IC. z Operation voltage from 3.5V to 14V. z Blinking frequency from 3.0Hz to 1.5Hz. z Electrostatic discharge and power surge could damage the LEDs. z It is recommended to use a wrist band or anti- z RoHS compliant. electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SPEC NO: DSAF2693 REV NO: V.7B DATE: MAR/16/2015 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101005621 Selection Guide Part No. Dice WP56BHD Lens Type Bright Red (GaP) Red Diffused Viewing Angle [1] Iv (mcd) V= 9V Min. Typ. 2θ1/2 1.2 4 60° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Min. Typ. λpeak Peak Wavelength Bright Red 700 nm λD Dominant Wavelength Bright Red 635 nm Δλ1/2 Spectral Line Half-width Bright Red 45 nm IF Forward Current Bright Red 22 mA Min:VF=3.5V Typ:VF=5V ISON Supply Current Bright Red 8 mA VF=3.5V ISON Supply Current Bright Red 44 mA VF=14V f Blink Frequency Bright Red Hz VF=3.5V~14V 8 Max. 1.5 3 Units Test Conditions Notes: 1.Wavelength value is traceable to the CIE127-2007 compliant national standards. 2.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Bright Red Units Power dissipation 310 mW Forward Voltage 14 V Reverse Voltage 0.5 V Operating Temperature -40°C To +70°C Storage Temperature -40°C To +85°C Lead Solder Temperature [1] 260°C For 3 Seconds Lead Solder Temperature [2] 260°C For 5 Seconds Notes: 1. 2mm below package base. 2. 5mm below package base. SPEC NO: DSAF2693 REV NO: V.7B DATE: MAR/16/2015 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101005621 Bright Red WP56BHD SPEC NO: DSAF2693 REV NO: V.7B DATE: MAR/16/2015 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101005621 PACKING & LABEL SPECIFICATIONS WP56BHD Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAF2693 REV NO: V.7B DATE: MAR/16/2015 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101005621 SPEC NO: DSAF2693 REV NO: V.7B DATE: MAR/16/2015 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101005621 SPEC NO: DSAF2693 REV NO: V.7B DATE: MAR/16/2015 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101005621