2.0x1.25mm SMD CHIP LED LAMP Part Number: AP2012SURCK Hyper Red Features Description z 2.0mmx1.25mm SMT LED,1.1mm thickness. The Hyper Red source color devices are made with Al- z Low power consumption. GaInP on GaAs substrate Light Emitting Diode. z Wide viewing angle. z Ideal for backlight and indicator. z Various colors and lens types available. z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAB0811 REV NO: V.9 DATE: JUN/08/2011 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1203000189 Selection Guide Part No. Dice AP2012SURCK Iv (mcd) [2] @ 20mA Lens Type Hyper Red (AlGaInP) Viewing Angle [1] Min. Typ. 2θ1/2 120 230 120° Water Clear Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Hyper Red λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 650 nm IF=20mA Hyper Red 630 nm IF=20mA Spectral Line Half-width Hyper Red 28 nm IF=20mA C Capacitance Hyper Red 35 pF VF=0V;f=1MHz VF [2] Forward Voltage Hyper Red 1.95 2.5 V IF=20mA IR Reverse Current Hyper Red 10 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 185 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAB0811 REV NO: V.9 DATE: JUN/08/2011 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1203000189 Hyper Red AP2012SURCK SPEC NO: DSAB0811 REV NO: V.9 DATE: JUN/08/2011 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1203000189 AP2012SURCK Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAB0811 REV NO: V.9 DATE: JUN/08/2011 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1203000189 PACKING & LABEL SPECIFICATIONS AP2012SURCK SPEC NO: DSAB0811 REV NO: V.9 DATE: JUN/08/2011 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1203000189