DA6285.002 11 November, 2010 MAS6285 IC FOR XO TRIMMING Very Low Power Wide Trimming Range Wide Supply Voltage Range Very High Level of Integration Electrically Trimmable Low Cost • • • • • • DESCRIPTION MAS6285 is capacitive digital to analog converter integrated circuit well suited to make initial offset trimming of the crystal oscillator. The trimming is done by a serial bus and the calibration information is stored in an internal PROM. FEATURES • • • • APPLICATIONS IC for Crystal oscillator offset trimming Very small size Minimum current draw Wide operating temperature range • • • High Frequency VCXOs OCXOs All Crystal Oscillators BLOCK DIAGRAM MAS6285 DA 2 CLK PV Digital 3 6 VDD VSS COUT Figure 1. Block diagram of MAS6285. 1 (12) DA6285.002 11 November, 2010 PIN DESCRIPTION Pin Description Serial Bus Data Input Serial Bus Clock Input Programming Input Power Supply Voltage Power Supply Ground CDAC Output Symbol x-coordinate y-coordinate DA CLK PV VDD VSS 150 369 593 150 369 141 141 140 689 689 COUT 593 689 Note Note: Because the substrate of the die is internally connected to VSS, the die has to be connected to VSS or left floating. Please make sure that VSS is the first pad to be bonded. Pick-and-place and all component assembly are recommended to be performed in ESD protected area. Note: Pad coordinates measured from the left bottom corner of the chip to the center of the pads. The coordinates may vary depending on sawing width and location, however, distances between pads are accurate. ABSOLUTE MAXIMUM RATINGS Parameter Symbol Min Max Unit Supply Voltage Input Voltage Power Dissipation (max) Storage Temperature Latch-Up Current Limit VDD - VSS VIN PMAX TST ILUT -0.3 VSS -0.3 6.0 VDD + 0.3 100 150 V V mW o C mA -55 ±100 Note 1) Note: Stresses beyond the values listed may cause a permanent damage to the device. The device may not operate under these conditions, but it will not be destroyed. Note: This is a CMOS device and therefore it should be handled carefully to avoid any damage by static voltages (ESD). Note 1: Not valid for programming pin PV RECOMMENDED OPERATION CONDITIONS Parameter Supply Voltage Operating Temperature Symbol Conditions VDD TOP Min Typ Max 2.5 -40 2.8 5.5 +85 Unit V C o ELECTRICAL CHARACTERISTICS (recommended operation conditions) Parameter Operating Frequency Capacitance Range Supply Current Symbol fOP COUT ICC Min 3.3 0.3 Typ Max Unit Note 200 34.3 10 MHz pF µA 1) 2) Note 1: Capacitance values are typical and may vary ± 25% due to the IC process variation. Capacitance range guaranteed by design. 2 (12) DA6285.002 11 November, 2010 Note 2: Minimum supply current is drawn when all bits are programmed as “0”. Maximum supply current is drawn when all bits are left unprogrammed “1”. IC OUTLINES VDD VSS COUT 830 um MAS6285 DA CLK PV Die map reference 760 um Figure 2. IC outline of MAS6285. Note 1: MAS6285 pads are round with 80 µm diameter at opening. Note 2: Pins PV, CLK and DA must not be connected in XO module end-user application. APPLICATION MAS6285 DA 2 CLK PV Digital 3 6 VDD VSS COUT VC OUT VCXO XIN XOUT X'Tal Figure 3. Typical application for MAS6285. 3 (12) DA6285.002 11 November, 2010 4 (12) DA6285.002 11 November, 2010 PIN CONFIGURATION (TSOT-6) TSOT-6 DA VDD 6 CLK 4 5 85AX 3 2 1 COUT VSS PV 85AX = Product version (MAS6285AX, where x = letter or number) Figure 4. TSOT-6 package. PIN DESCRIPTION (TSOT-6) Pin Name Pin Number in TSOT-6 Type COUT VSS PV CLK DA VDD 1 2 3 4 5 6 O G I I I P Function CDAC Output with Bias Option Power Supply Ground Programming Input Serial Bus Clock Input Serial Bus Data Input Power Supply Voltage G = Ground, I = Input, O = Output, P = Power 5 (12) DA6285.002 11 November, 2010 PIN CONFIGURATION (QFN-6) QFN-6 85X ZZZ COUT VSS VDD PV CLK DA 85X = Product version (MAS6285X, where X = letter or number) ZZZ = MAS lot number (3 last digit) Figure 5. QFN-6 package. PIN DESCRIPTION (QFN-6) Pin Name Pin Number in TSOT-6 Type COUT VSS VDD DA CLK PV 1 2 3 4 5 6 O G P I I I Function CDAC Output with Bias Option Power Supply Ground Power Supply Voltage Serial Bus Data Input Serial Bus Clock Input Programming Input G = Ground, I = Input, O = Output, P = Power Exposed pad* can be connected to ground or left floating * see package outline information on page 8 6 (12) DA6285.002 11 November, 2010 PACKAGE OUTLINE (TSOT-6) e GAUGE PLANE b CL CL E L2 L CL E1 e1 D c CL 1) PACKAGE OUTLINE DIMENSIONS INCLUSIVE OF METAL BURR & SOLDER PLATING A A2 2) PACKAGE OUTLINE EXCLUSIVE OF MOLD FLASH A1 3) ALL SPECIFICATIONS COMPLY TO JEDEC MO193 4) Q REFERS TO ALL PACKAGE DRAFT ANGLES Symbol Min Nom Max Unit A A1 A2 b c D E E1 e e1 L L2 Q -0.01 0.84 0.30 0.12 -0.05 0.87 -0.127 2.90BSC 2.80BSC 1.60BSC 0.95BSC 1.90BSC 0.40 0.25BSC 10° 1.00 0.10 0.90 0.45 0.20 mm mm mm mm mm mm mm mm mm mm mm mm 0.30 4° 0.50 12° 7 (12) DA6285.002 11 November, 2010 SOLDERING INFORMATION (TSOT-6) ◆ For Lead-Free / RoHS Compliant Green TSOT-6 Resistance to Soldering Heat Maximum Temperature Maximum Number of Reflow Cycles Reflow profile According to RSH test IEC 68-2-58/20 260°C 3 Thermal profile parameters stated in JESD22-A113 should not be exceeded. http://www.jedec.org max 0.08 mm Solder plate 7.62 - 25.4 µm, material Matte Tin Seating Plane Co-planarity Lead Finish TAPE & REEL SPECIFICATIONS (TSOT-6) W3 W2 Feeding Direction A D N C 8 mm W1 85AX 85AX B 4 mm Other Dimensions according to EIA-481 Standard 3000 Components on Each Reel Dimension A B C D N W 1 (measured at hub) W 2 (measured at hub) W 3 (includes flange distortion at outer edge) Trailer Leader Min 1.5 12.80 20.2 50 8.4 7.9 160 390, of which minimum 160 mm of empty carrier tape sealed with cover tape Max Unit 178 mm mm mm mm mm mm mm mm mm mm 13.50 9.9 14.4 10.9 8 (12) DA6285.002 11 November, 2010 PACKAGE OUTLINE (QFN-6) D TOP VIEW E/2 D/2 A SIDE VIEW A3 PIN 1 MARK AREA A1 SEATING PLANE D2/2 L E2/2 D2 E2 SHAPE OF PIN #1 IDENTIFICATION IS OPTIONAL BOTTOM VIEW b EXPOSED PAD e Symbol Min A A1 A3 b D D2 (Exposed pad) E E2 (Exposed pad) e L 0.700 0.000 0.178 0.200 1.350 0.750 0.300 Nom PACKAGE DIMENSIONS 0.750 0.020 0.203 0.250 2.000 BSC 1.400 2.000 BSC 0.800 0.650 BSC 0.350 Max Unit 0.800 0.050 0.228 0.300 mm mm mm mm mm mm mm mm mm mm 1.450 0.850 0.400 Dimensions do not include mold or interlead flash, protrusions or gate burrs. 9 (12) DA6285.002 11 November, 2010 SOLDERING INFORMATION (QFN-6) ◆ For Lead-Free / RoHS Compliant Green QFN Resistance to Soldering Heat Maximum Temperature Maximum Number of Reflow Cycles Reflow profile Lead Finish According to RSH test IEC 68-2-58/20 260°C 3 Thermal profile parameters stated in IPC/JEDEC J-STD-020 should not be exceeded. http://www.jedec.org 7.62 - 25.4 µm, Matte Tin EMBOSSED TAPE SPECIFICATIONS (QFN-6) Pin 1 orientation / top view DO PO P2 P1 T X E W 10 O MAX F B0 X A0 K0 User Direction of Feed Detail X-X Dimension Min/Max Unit Ao Bo Do E F Ko Po P1 P2 T W 2.30 ±0.05 2.30 ±0.05 1.50 +0.1/-0.0 1.75 ±0.10 3.50 ±0.05 1.00 ±0.05 4.0 4.0 ±0.10 2.0 ±0.05 0.254 ±0.02 8.00 ±0.3/-0.1 mm mm mm mm mm mm mm mm mm mm mm 10 (12) DA6285.002 11 November, 2010 REEL SPECIFICATIONS (QFN-6) W2 A D C Tape Slot for Tape Start N B W1 Carrier Tape Cover Tape End Start Trailer Dimension Components Min A B C D N W 1 (measured at hub) W 2 (measured at hub) Trailer Leader 1.5 12.80 20.2 50 8.4 Leader Max Unit 178 mm mm mm mm mm mm mm mm mm 13.50 9.90 14.4 160 390, of which minimum 160 mm of empty carrier tape sealed with cover tape 3000 Components on Each Reel Reel Material: Conductive, Plastic Antistatic or Static Dissipative Carrier Tape Material: Conductive Cover Tape Material: Static Dissipative 11 (12) DA6285.002 11 November, 2010 ORDERING INFORMATION Product Code Product Package MAS6285AA1WA900 MAS6285AA1T0206 IC FOR XO Trimming IC FOR XO Trimming MAS6285AA1Q1806 IC FOR XO Trimming Tested wafers 215 µm TSOT-6 Pb-free, RoHS compliant QFN-6 Pb-free, RoHS compliant Comments T&R/3000 pcs/reel T&R/3000 pcs/reel Please contact Micro Analog Systems Oy for other wafer thickness options. ◆ The formation of product code Product name MAS6285 Design version AA1 Package type WA9 = 215 µm thick EWS tested wafer T02 = TSOT-6 RoHS Compliant Q18 = QFN-6 RoHS Compliant Delivery format 00 = bare wafer 06 = tape & reel LOCAL DISTRIBUTOR MICRO ANALOG SYSTEMS OY CONTACTS Micro Analog Systems Oy Kutomotie 16 FI-00380 Helsinki, FINLAND Tel. +358 10 835 1100 Fax +358 10 835 1119 http://www.mas-oy.com NOTICE Micro Analog Systems Oy reserves the right to make changes to the products contained in this data sheet in order to improve the design or performance and to supply the best possible products. Micro Analog Systems Oy assumes no responsibility for the use of any circuits shown in this data sheet, conveys no license under any patent or other rights unless otherwise specified in this data sheet, and makes no claim that the circuits are free from patent infringement. Applications for any devices shown in this data sheet are for illustration only and Micro Analog Systems Oy makes no claim or warranty that such applications will be suitable for the use specified without further testing or modification. 12 (12)