FIBER OPTIC LED IN SMA HOUSING

66217
FIBER OPTIC LED IN SMA HOUSING
OPTOELECTRONIC PRODUCTS
DIVISION
04/09/2013
Features:
Applications:








Fiberoptic LED with internal ball lens
Industry standard SMA style connector
High coupled output power 60 W @60 mA
(100 micron fiber) typical
Data rates up to 10 MHz
850 nm wavelength
Short haul data Link
Mobile Communications
Local Area Networks
DESCRIPTION
The 66217 series, high speed fiber-optic LED is packaged in an industry standard SMA housing. An internal “glass ball” lens
focuses the light from the die to increase light coupling for 50 to 150 micron multi-mode optical fibers. Typical coupled power
is greater than –12 dbm (60 W) into a 100 micron fiber at 60 mA. With rise and fall times of 10 ns maximum, this part may be
used in medium to high speed data transmission applications. This LED may be screened to meet specific customer
requirements or to MIL-PRF-19500.
ABSOLUTE MAXIMUM RATINGS 25°C FREE AIR TEMPERATURE UNLESS NOTED
Reverse Voltage ..................................................................................................................................................................... 1 Vdc
Forward Continuous Current (Note 1)………………………………………………………………………………......... ……. 100 mA
Transmission Rate at 100 mA IF …….…………………………………….…………………………… .......... ……………..10 Mbits/s
Storage Temperature............................................................................................................................................. -55°C to +150°C
Operating Temperature ......................................................................................................................................... -40°C to +125°C
Soldering Temperature (10 seconds, 1/16” from case).......... .............................................................................................. 240°C
NOTES:
1. Derate linearly at 1mA/°C above 25°C.
Package Dimensions
Schematic Diagram
ANODE
0.597+0.008
-0.007
0.280
0.230±0.020
0.075
PIN 2
CATHODE
0.380 0.500
PIN 1
0.140
PIN 3
N/C
0.380
Ø0.100
0.250-36 UNS-2A
0.086-56 UNC-2B
2 PLCS
0.400
MIN.
PIN 1
ANODE
0.086-56 UNC-2B
2 PLCS
PIN 2
CATHODE
UNLESS OTHERWISE SPECIFIED, TOLERANCE IS ±0.005.
ALL DIMENSIONS ARE IN INCHES.
MICROPAC INDUSTRIES, INC. OPTOELECTRONIC PRODUCTS DIVISION  725 E.Walnut St., Garland, TX 75040  (972)272-3571  Fax (972)487-6918
www.micropac.com E-MAIL: OPTOSALES @ MICROPAC.COM
66217
FIBER OPTIC LED IN SMA HOUSING
04/09/2013
ELECTRICAL CHARACTERISTICS
TA = 25C unless otherwise specified.
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
TEST CONDITIONS
2
V
IF = 100 mA
VF
Forward Voltage
BVR
1
V
IR = 10 A
Coupled Power Output
Po
90
W
IF = 100 mA
Output Rise Time
tR
8
10
ns
Output Fall Time
tF
6
10
ns
Peak Wavelength
p
850
Reverse Breakdown Voltage
NOTE
1
IF = 100 mA
5 mA pre-bias
IF = 100 mA
5 mA pre-bias
ns
IF = 100 mA
NOTES:
1.
Tested using a 100/140 m fiber (NA = 0.29). Actual coupled power may vary due to alignment, receptacle and fiber.
RECOMMENDED OPERATING CONDITIONS:
PARAMETER
Forward Current
SYMBOL
MIN
MAX
UNITS
IF
20
100
mA
Transmission Rate
10
Mb/sec
SELECTION GUIDE
PART NUMBER
PART DESCRIPTION
66217-001
Commercial
66217-101
Screened to TX level
MICROPAC INDUSTRIES, INC. OPTOELECTRONIC PRODUCTS DIVISION  725 E.Walnut St., Garland, TX 75040  (972)272-3571  Fax (972)487-6918
www.micropac.com E-MAIL: OPTOSALES @ MICROPAC.COM