Technical Brief 347 Tape and Reel Specification for Integrated Circuits Introduction Many Surface Mounted Devices (SMDs) are being packaged for shipment in embossed tape and wound onto reels. The Intersil tape and reel specifications are in compliance with Electronics Industries Association (EIA) standards for “Embossed Carrier Taping of Surface Mount Components for Automatic Handling”. • EIA-481 for the . . . . . . . . . . . . . . . . . . . 8, 12, 16, 24, 32, 44 and 56mm Wide Tape (Except the orientation of square package) Intersil now supplies many different SMDs in tape and reel, as shown in Table 1. TABLE 1. PACKAGE AND TAPE SPECIFICATIONS TRAILER “A” LEADER “B” POCKET TAPE # OF LEADS NOMINAL PACKAGE SIZE UNITS PER REEL REEL AND HUB SIZE (Note 3) xxxxxxx-T7A Note 4 Note 5 250 7&2.4 Note 5 Note 5 Note 5 Note 5 Note 5 Note 5 xxxxxxx-T7 Note 4 Note 5 Note 5 7&2.4 Note 5 Note 5 Note 5 Note 5 Note 5 Note 5 SOIC(N) (SOPN) 8 0.155x0.194" 2500/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm SOIC(N) (SOPN) 14 0.155x0.342" 2500/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 16mm 8mm SOIC(N) (SOPN) 16 0.155x0.391" 2500/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 16mm 8mm SOIC(W) (SOPW) 16 0.296x0.407" 1,000/250 13&4/7&2.4 34 420mm 45 552mm 16mm 12mm SOIC(W) (SOPW) 18 0.296x0.456" 1,000 13&4 34 420mm 45 552mm 24mm 12mm SOIC(W) (SOPW) 20 0.296x0.506" 1,000 13&4 34 420mm 45 552mm 24mm 12mm SOIC(W) (SOPW) 24 0.296x0.606" 1,000 13&4 34 420mm 45 552mm 24mm 12mm SOIC(W) (SOPW) (or EPSOIC) 28 0.296x0.706" 1,000 13&4 26 416mm 34 544mm 32mm 16mm EIAJ SOIC 8 0.217x0.217" 2,500 13&4 77 616mm 77 616mm 12mm 8mm MSOP 8/10 3.0x3.0mm 2500/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm TSSOP 8 4.4x3.0mm 2500/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm TSSOP (or EPTSSOP) 14/16 4.4x5.0mm 2500/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm TSSOP (Custom) 14/16 4.4x5.0mm 2500/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 16mm 8mm 20 4.4x6.5mm 2500/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 16mm 8mm PACKAGE TYPE TSSOP July 16, 2015 TB347.26 1 POCKETS LENGTH POCKETS LENGTH WIDTH PITCH (P1) CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. Copyright Intersil Americas LLC 2005-2007, 2009-2015. All Rights Reserved. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. Technical Brief 347 TABLE 1. PACKAGE AND TAPE SPECIFICATIONS (Continued) # OF LEADS NOMINAL PACKAGE SIZE UNITS PER REEL REEL AND HUB SIZE (Note 3) TSSOP (or EPTSSOP) 24 4.4x7.8mm 2500/1000/ 250 TSSOP (or EPTSSOP) 28/38 4.4x9.7mm TSSOP 48 QSOP (SSOP) PACKAGE TYPE TRAILER “A” LEADER “B” POCKET TAPE POCKETS LENGTH POCKETS LENGTH WIDTH PITCH (P1) 13&4/13&4/ 7&2.4 77 616mm 77 616mm 16mm 8mm 2500/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 16mm 8mm 12.5x6.1mm 1000 13&4 50 600mm 50 600mm 24mm 12mm 16 0.155x0.194" 2500/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm QSOP (SSOP) 20/24 0.155x0.342" 2500/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 16mm 8mm QSOP (SSOP) 28 0.155x0.391" 2500/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 16mm 8mm SSOP 16 0.209x0.244" 1,000/250 13&4/7&2.4 24 420mm 45 552mm 16mm 12mm SSOP 20 0.209x0.284" 1,000/250 13&4/7&2.4 34 420mm 45 552mm 16mm 12mm SSOP 24 0.209x0.323" 1,000/250 13&4/7&2.4 34 420mm 45 552mm 16mm 12mm SSOP 28 0.209x0.402" 1,000 13&4 34 420mm 45 552mm 24mm 12mm PLCC 20 0.350x0.350" 1,000 13&4 53 660mm 64 792mm 16mm 12mm PLCC 28 0.450x0.450" 750 13&4 15 256mm 25 416mm 24mm 16mm PLCC 32 0.450x0.550" 750 13&4 15 256mm 25 416mm 24mm 16mm PLCC 44 0.650x0.650" 500 13&4 15 384mm 25 624mm 32mm 24mm PLCC 68 0.950x0.950" 250 13&6 25 832mm 25 832mm 44mm 32mm PLCC 84 1.150x1.150" 200 13&6 25 936mm 25 936mm 44mm 36mm TQFP 32 5x5x1.0mm 2,000/1000 13&6/13&6 33 400mm 33 400mm 16mm 12mm TQFP/EPAD TQFP 32/48 7x7x1.0mm 1,000 13&6 34 420mm 45 552mm 16mm 12mm TQFP/EPAD 64/44 10x10x1.0mm 1,000 13&4 26 420mm 35 552mm 24mm 16mm TQFP 64/44 10x10x1.0mm 1,000 13&6 25 400mm 30 480mm 24mm 16mm TQFP 80 14x14x1.0mm 1,000 13&4 10 240mm 20 480mm 24mm 24mm TQFP (Techwell) 80 12x12x1.0mm 1,000 13&4 25 600mm 25 600mm 24mm 24mm TQFP 100 12x12x10mm 3000 13&4 50 1200mm 50 1200mm 24mm 24mm LQFP 48 7x7x1.4mm 1,000 13&6 34 420mm 45 552mm 16mm 12mm LQFP 80 10x10x1.4mm 1,000 13&4 25 400mm 30 480mm 24mm 16mm LQFP 80 14x14x1.4mm 500 13&4 21 420mm 28 552mm 32mm 24mm LQFP 128 14x20x1.4mm 1000 13&4 10 160mm 20 390mm 44mm 24mm LQFP (Techwell) 128 14x20x1.4mm 500 13&4 25 600mm 25 600mm 44mm 24mm LQFP (or PQLQP) 144 20x20x1.4mm 600 13&6 15 320mm 25 640mm 44mm 32mm LQFP 160 24x24x1.4mm 500 13&6 20 640mm 20 640mm 44mm 32mm LQFP 208 28x28x1.4mm 500 13&6 10 360mm 20 720mm 44mm 36mm MQFP 44 10x10x2.0mm 500 13&6 25 624mm 25 624mm 24mm 24mm MQFP 80 14x20x2.7mm 500 13&6 10 193mm 20 385mm 44mm 24mm 128 14x20x2.72mm 500 13&6 25 600mm 25 600mm 44mm 24mm QFP Submit Document Feedback 2 TB347.26 July 16, 2015 Technical Brief 347 TABLE 1. PACKAGE AND TAPE SPECIFICATIONS (Continued) TRAILER “A” LEADER “B” POCKET TAPE # OF LEADS NOMINAL PACKAGE SIZE UNITS PER REEL REEL AND HUB SIZE (Note 3) PBGA (fBGA) 160/196 12x12x1.4mm 1,000 13&6 25 400mm 30 480mm 24mm 16mm PBGA (fBGA) 192 14x14x1.32mm 1,000 13&6 10 240mm 20 480mm 24mm 24mm PBGA (fBGA) 196 15x15x1.4mm 750 13&6 10 240mm 20 480mm 24mm 24mm PBGA (fBGA) 256/316 17x17x1.4mm 500 13&6 10 240mm 20 480mm 24mm 24mm TFBGA (Techwell) 144 7x7x1.2mm 2500 13&4 50 600mm 50 600mm 16mm 12mm TFBGA (Techwell) 144 7x7x1.3mm 2500 13&4 50 600mm 50 600mm 16mm 12mm TDFN Note 4 1.6x1.6x0.75mm 1000/250 7&2.4/7&2.4 100 400mm 100 400mm 8mm 4mm TDFN Note 4 2.0x2.0x0.75mm 1000/250 7&2.4/7&2.4 100 400mm 100 400mm 8mm 4mm TDFN (13” Packing) Note 4 2.0x2.0x0.75mm 6000 13&4 100 400mm 100 400mm 8mm 4mm TDFN Note 4 2x3x0.75mm 6000/1000/ 250 13&4 /13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm TDFN Note 4 3x3x0.75mm 6000/1000/ 250 13&4 /13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm TDFN Note 4 4x3x0.75mm 6000/1000/ 250 13&4 /13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm TDFN Note 4 4x4x0.75mm 6000/1000/ 250 13&4 /13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm TDFN Note 4 5x3x0.75mm 4,000/1000/ 13&4 /13&4/ 250 7&2.4 77 616mm 77 616mm 12mm 8mm DFN Note 4 2x2x0.9mm 6,000/250 13&4/7&2.4 77 616mm 77 616mm 12mm 8mm DFN Note 4 2x3x0.9mm 6,000/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm DFN Note 4 3x3x0.9mm 6000/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm DFN Note 4 4x3x0.9mm 6000/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm DFN Note 4 4x4x0.9mm 6000/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm DFN Note 4 4x5.5x1.3mm 4,000/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm DFN Note 4 5x3x0.9mm 4,000/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm QFN/TQFN Note 4 3x3x0.9/ 0.75mm 6000/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm QFN (Zilker Lab) Note 4 3x3x0.9mm 6000/1000/ 100 13&4/13&4/ 7&2.4 20 160mm 50 400mm 12mm 8mm QFN (Quellan) Note 4 3x3x0.9mm 1000/100 7&2.4 77 616mm 77 616mm 12mm 8mm QFN/TQFN Note 4 3x4x0.9/ 0.75mm 6000/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm QFN/TQFN Note 4 3.5x3.5x0.9/ 0.75mm 6000/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm PACKAGE TYPE Submit Document Feedback 3 POCKETS LENGTH POCKETS LENGTH WIDTH PITCH (P1) TB347.26 July 16, 2015 Technical Brief 347 TABLE 1. PACKAGE AND TAPE SPECIFICATIONS (Continued) # OF LEADS NOMINAL PACKAGE SIZE UNITS PER REEL REEL AND HUB SIZE (Note 3) QFN/TQFN Note 4 4x4x0.9/ 0.75mm 6000/1000/ 250 QFN/TQFN Note 4 4x5x0.9/ 0.75mm QFN/TQFN Note 4 QFN (Quellan) PACKAGE TYPE TRAILER “A” LEADER “B” POCKET TAPE POCKETS LENGTH POCKETS LENGTH WIDTH PITCH (P1) 13&4/13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm 6000/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm 4x6x0.9/ 0.75mm 4,000/1000/ 250 13&4/13&4/ 7&2.4 34 420mm 45 552mm 16mm 12mm Note 4 4x7x0.9mm 1000/ 100 7&2.4/7&2.4 77 616mm 77 616mm 16mm 8mm QFN/TQFN Note 4 5x5x0.9/ 0.75mm 6000/1000/ 250 13&4/13&4/ 7&2.4 77 616mm 77 616mm 12mm 8mm QFN (Zilker Lab) Note 4 5x5x0.9mm 6000/1000/ 100 13&4/13&4/ 7&2.4 20 160mm 50 400mm 12mm 8mm QFN/TQFN Note 4 5x7x0.9/ 0.75mm 2500/1000/ 250 13&4/13&4/ 7&2.4 20 160mm 48 390mm 16mm 8mm 32 5x6x0.9mm 6000/2500/ 1000 13&4/13&4/ 7&2.4 100 800mm 100 800mm 12mm 8mm QFN/TQFN Note 4 5x10x0.9/ 0.75mm 4,000/1000 13&4/13&4 34 420mm 45 552mm 24mm 12mm QFN/TQFN Note 4 6x4x0.9/ 0.75mm 4000/1000/ 250 13&4/13&4/ 7&2.4 34 420mm 45 552mm 16mm 12mm QFN/TQFN Note 4 6x6x0.9/ 0.75mm 4000/1000/ 250 13&4/13&4/ 7&2.4 34 420mm 45 552mm 16mm 12mm QFN (Zilker Lab) Note 4 6x6x0.9mm 1000/100 13&4/7&2.4 14 160mm 34 400mm 16mm 12mm QFN/TQFN Note 4 7x7x0.9/ 0.75mm 4,000/1000/ 250 13&4/13&4/ 7&2.4 34 420mm 45 552mm 16mm 12mm QFN (Techwell) Note 4 7x7x0.9mm 3,000 13&4 15 180mm 35 420mm 16mm 12mm QFN/TQFN Note 4 8x8x0.9/ 0.75mm 4,000/1000/ 250 13&4/13&4/ 7&2.4 34 420mm 45 552mm 16mm 12mm QFN/TQFN Note 4 9x9x0.9/ 0.75mm 4,000/1000/ 250 13&4/13&4/ 7&2.4 34 408mm 45 540mm 16mm 12mm QFN/TQFN Note 4 10x10x0.9/ 0.75mm 3,000/1000/ 250 13&4/13&4/ 7&2.4 26 416mm 34 544mm 24mm 16mm QFN/HDA Note 4 15x15x3.5/ 2.2mm 500 13&4 20 400mm 20 400mm 24mm 20mm QFN/HDA Note 4 15x15x3.6mm 500 13&4 20 400mm 20 400mm 24mm 20mm QFN/HDA (Punch QFN) 26 17x17x7.5mm 250 13&4 10 240mm 20 480mm 24mm 24mm QFN/HDA 27 17.2x11.45x2.5mm 1000 13&4 10 200mm 20 400mm 24mm 20mm QFN/HDA 40 17.0x19.0x3.55mm 500 13&4 10 240mm 20 480mm 32mm 24mm QFN/HDA 42 18.0x23.0x7.5mm 250 13&4 10 240mm 20 480mm 32mm 24mm X2QFN 28 4x5x0.38mm 6000 13&4 77 616mm 77 616mm 12mm 8mm aQFN 69 5x5x0.85mm 1000/100 7&2.4/7&2.4 77 616mm 77 616mm 12mm 8mm WFQFN 40 6.0x6.0x0.85mm 4000/1000 13&4/13&4 34 420mm 45 552mm 16mm 12mm MO-169 (TO-262) 3/7 0.400x0.415" 800 13&4 50 800mm 50 800mm 24mm 16mm QFN Submit Document Feedback 4 TB347.26 July 16, 2015 Technical Brief 347 TABLE 1. PACKAGE AND TAPE SPECIFICATIONS (Continued) TRAILER “A” LEADER “B” POCKET TAPE # OF LEADS NOMINAL PACKAGE SIZE UNITS PER REEL REEL AND HUB SIZE (Note 3) SOT-23 3 0.051x0.115" 3000/1000 7&2.4/7&2.4 40 160mm 100 400mm 8mm 4mm SOT-23 5/6/8 0.065x0.115" 3000/1000 7&2.4/7&2.4 63 250mm 126 500mm 8mm 4mm SC70 3 0.049x0.079" 3000/1000 7&2.4/7&2.4 40 160mm 100 400mm 8mm 4mm SC70 5/6 0.049x0.079" 3000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 4 1.16x0.98mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 6 1.36x0.8mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 6 1.0x1.5mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 9 1.45x1.45mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 9 1.32x1.54mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 12 1.48x1.98mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 12 1.39x1.69mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 12 1.70x1.30mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 15 1.51x2.15mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 16 1.74x1.74mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 16 1.78x1.78mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 20 2.55x2.05mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 20 1.72x2.335mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 12mm 4mm WLCSP 20 1.82x2.15mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 20 2.07x1.67mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 20/24 1.60x2.40mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 25 2.11x2.13mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 25 2.13x2.11mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 16 2.16x2.16mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 25 2.33x2.07mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 25 2.64x2.64mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 28 2.92x2.185mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 12mm 4mm WLCSP (8mm) 30 2.33x2.61mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 30 2.33x2.61mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 12mm 4mm WLCSP 36 2.53x2.53mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm WLCSP 46 2.82x3.31mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 12mm 4mm WLCSP 40 3.27x2.01mm 3,000/1000 7&2.4/7&2.4 95 380mm 125 500mm 12mm 4mm WLCSP 56 3.11x3.21mm 3000 13/4 250 2000mm 150 1200mm 12mm 8mm WLCSP 56 3.22x3.37mm 3000 13/4 250 2000mm 150 1200mm 12mm 8mm WLCSP 64 4.04x4.04mm 3000 7&2.4 95 380mm 125 500mm 12mm 4mm WLCSP 72 4.00x4.50mm 3000 13/4 20 160mm 50 400mm 12mm 8mm WLCSP 121 5.526x5.540mm 3000 13/4 250 2000mm 150 1200mm 12mm 8mm OCSP 9 2.13x2.13mm 2,500 7&2.4/7&2.4 95 380mm 125 500mm 8mm 4mm µTDFN 6 1.2x1.0x0.50mm 3,000/1000/ 250 7&2.4/7&2.4 /7&2.4 100 400mm 100 400mm 8mm 4mm PACKAGE TYPE Submit Document Feedback 5 POCKETS LENGTH POCKETS LENGTH WIDTH PITCH (P1) TB347.26 July 16, 2015 Technical Brief 347 TABLE 1. PACKAGE AND TAPE SPECIFICATIONS (Continued) # OF LEADS NOMINAL PACKAGE SIZE UNITS PER REEL REEL AND HUB SIZE (Note 3) µTDFN 6 1.6x1.6x0.50mm 3,000/1000/ 250 µTDFN 8 2.0x2.0x0.50mm µTQFN 8 µTQFN PACKAGE TYPE TRAILER “A” LEADER “B” POCKET TAPE POCKETS LENGTH POCKETS LENGTH WIDTH PITCH (P1) 7&2.4/7&2.4 /7&2.4 100 400mm 100 400mm 8mm 4mm 3,000/1000/ 250 7&2.4/7&2.4 /7&2.4 100 400mm 100 400mm 8mm 4mm 1.4x1.2x0.50mm 3,000/1000/ 250 7&2.4/7&2.4 /7&2.4 100 400mm 100 400mm 8mm 4mm 10 1.8x1.4x0.50mm 3,000/1000/ 250 7&2.4/7&2.4 /7&2.4 100 400mm 100 400mm 8mm 4mm µTQFN 10 2.1x1.6x0.50mm 3,000/1000/ 250 7&2.4/7&2.4 /7&2.4 100 400mm 100 400mm 8mm 4mm µTQFN 12 2.2x1.4x0.50mm 3,000/1000/ 250 7&2.4/7&2.4 /7&2.4 100 400mm 100 400mm 8mm 4mm µTQFN 16 2.6x1.8x0.50mm 3,000/1000/ 250 7&2.4/7&2.4 /7&2.4 100 400mm 100 400mm 8mm 4mm µTQFN 20 3.2x1.8x0.50mm 3,000/1000/ 250 7&2.4/7&2.4 /7&2.4 100 400mm 100 400mm 8mm 4mm ODFN 4 1.5x1.5x0.70mm 3,000/1000/ 250 7&2.4/7&2.4 /7&2.4 40 160mm 100 400mm 8mm 4mm ODFN 5/6/8 2.0x2.1x0.70mm 3,000/1000/ 250 7&2.4/7&2.4 /7&2.4 40 160mm 100 400mm 8mm 4mm ODFN 10 2.1x3.5x0.65mm 1,000/250 7&2.4/7&2.4 40 160mm 100 400mm 12mm 4mm ODFN 8 3.0x3.0x0.70mm 1,000/250 7&2.4/7&2.4 40 160mm 100 400mm 8mm 4mm ODFN 8 2.36x2.94x 1.35mm 1,000/250 7&2.4/7&2.4 40 320mm 100 800mm 12mm 8mm NOTES: 1. Pocket count and trailer and leader lengths are nominal counts/dimensions. 2. Package size in inches (unless otherwise indicated). 3. Reel and hub size; Example: 13&4 = 13 inch reel with 4 inch hub. 4. Multiple lead counts. 5. Dependent upon the specific package type. Reference specific package type and number of leads in Table 1 for additional information. Submit Document Feedback 6 TB347.26 July 16, 2015 Technical Brief 347 General Information The Intersil tape and reel packing system protects the product from mechanical and electrical damage and is designed for automatic pick-and-place equipment. All tape sizes are supplied on 7inch and 13inch diameter reels. The tape and reel packing system consists of a pocket carrier tape sealed with a protective cover tape to hold the devices in place. Information labels, ESD labels and barcode labels (if required) are placed on each reel. The conductive carrier tape and antistatic coated transparent cover tape and reel, provide ESD protection. The devices are loaded with leads down, into the carrier pockets. Transparent cover tape allows device verification and brand inspection without having to remove or handle components. The tape is wound onto a plastic reel for labeling and packing for shipment. No more than 2 date codes will be combined on any one reel. ANY ADDITIONAL LABEL (IF REQUIRED) NOTE: LABELS TO BE PLACED ON THE REEL OPPOSITE THE ROUND (TAPE) SPROCKET HOLES. ESD CAUTION WAREHOUSE LABEL IF REQUIRED TOP COVER TAPE BARCODE LABEL IF REQUIRED SPROCKET HOLE (ROUND) CARRIER TAPE EMBOSSED CAVITY FIGURE 1. TAPE/REEL AND LABEL INFORMATION CARRIER TAPE COVER TAPE END START COMPONENTS TRAILER COVER TAPE POCKETS AND LENGTH “A” LEADER POCKETS AND LENGTH “B” FIGURE 2. TAPE LEADER AND TRAILER Submit Document Feedback 7 TB347.26 July 16, 2015 Technical Brief 347 Materials and Design Cover Tape Carrier Tape The cover tape is made of antistatic transparent polyester film. The surface resistivity is less than 1010Ω/sq. maximum. The pocketed carrier tape is made of conductive polystyrene plus carbon material (or equivalent). The surface resistivity is 106Ω/sq. maximum. The cover tape is heat-sealed or pressure sealed to the edges of the carrier tape to encase the devices in the pockets. The force to peel back the cover tape from the carrier tape shall be a mean value of 30gm to 80gm (0.3N to 0.8N). Pocket tapes are designed in such a manner that the components remain in position for automatic handling after the removal of the cover tape. Reel Each pocket has a hole in the center for automated sensing of whether or not the pocket is occupied, thus facilitating device removal. The device loading orientation is in compliance with EIA-481 (see Figure 5). The loaded carrier tape is wound onto a reel that is uniformly sized for all packages, (see Figure 6). Sprocket holes along the edge of the carrier tape enable direct feeding into automated board assembly equipment. The reel is made of antistatic high impact polystyrene. The surface resistivity is less than 1010Ω/sq. maximum. See Figures 3 and 4 for Carrier Tape dimensions. PO P2 DO E1 EMBOSSMENT T Ao Ko B1 F E2 Bo CENTER LINES OF CAVITY P1 W D1 FIGURE 3. CONFIGURATION DRAWING FOR 8, 12, 16, 24mm POCKET TAPE W (NOMINAL) TAPE WIDTH B1 (MAXIMUM) (Note 10) F (NOMINAL) E2 (MINIMUM) 8mm (0.315) 4.35 (0.171) 3.5 (0.138) 6.25 (0.246) 12mm (0.472) 8.2 (0.323) 5.5 (0.217) 10.25 (0.404) 16mm (0.629) 12.1 (0.476) 7.5 (0.295) 14.25 (0.561) 24mm (0.945) 20.1 (0.791) 11.5 (0.453) 22.25 (0.876) NOTES: 6. Dimensions are in millimeters and are nominal unless otherwise indicated (inches are in brackets for reference only). 7. “T” dimension, nominal 0.30 or 0.35. 8. “P1” cavity pitch is 4.0mm minimum and increases in 4.0mm increments depending on package size (see Table 1). 9. “P0” dimension is 4.0mm. 10. “P2” dimension is 2.0mm. 11. “B1” actual dimension is determined by package size. 12. “D1” diameter is 1.5mm minimum. 13. “Do” diameter is 1.5mm. 14. “E1” dimension is 1.75mm. 15. “Ao”, “Bo”, “Ko” dimensions determined by component size. Submit Document Feedback 8 TB347.26 July 16, 2015 Technical Brief 347 PO Do E1 P2 T Ao F 0.05(0.002) MAX B1 Bo Ko W P1 SO 0.20(.008) D1 DO/2 FIGURE 4. CONFIGURATION DRAWING FOR 32mm AND 44mm POCKET TAPE W (NOMINAL) TAPE WIDTH B1 (MAXIMUM) (Note 20) F (NOMINAL) SO (NOMINAL) 32mm (1.260) 23.0 (0.906) 14.2 (0.559) 28.4 (1.118) 44mm (1.732) 35.0 (1.378) 20.2 (0.795) 40.4 (1.591) NOTES: 16. Dimensions are in millimeters and are nominal unless otherwise indicated (inches are in brackets for reference only). 17. “T” dimension, nominal 0.30 or 0.35. 18. “P1” cavity pitch is 8.0mm minimum and increases in 4.0mm increments depending on package size (see Table 1). 19. “P0” dimension is 4.0mm. 20. “P2” dimension is 2.0mm. 21. “B1” actual dimension is determined by package size. 22. “D1” diameter is 2.0mm minimum. 23. “Do” diameter is 1.5mm. 24. “E1” dimension is 1.75mm. 25. “Ao”, “Bo”, “Ko” dimensions determined by component size. Submit Document Feedback 9 TB347.26 July 16, 2015 Technical Brief 347 USER DIRECTION OF FEED FIGURE 5A. SQUARE - BGA, QFN, DFN AND CSP USER DIRECTION OF FEED FIGURE 5B. RECTANGULAR - QFN AND DFN USER DIRECTION OF FEED FIGURE 5C. PLCC Submit Document Feedback 10 TB347.26 July 16, 2015 Technical Brief 347 USER DIRECTION OF FEED FIGURE 5D. SQUARE - MQFP, TQFP AND LQFP USER DIRECTION OF FEED FIGURE 5E. RECTANGULAR - MQFP, TQFP AND LQFP USER DIRECTION OF FEED FIGURE 5F. SOIC, MSOP, TSSOP, QSOP AND PSOP Submit Document Feedback 11 TB347.26 July 16, 2015 Technical Brief 347 PIN 1 USER DIRECTION OF FEED FIGURE 5G. SOT-23 AND SC-70 USER DIRECTION OF FEED FIGURE 5H. MO-169 USER DIRECTION OF FEED FIGURE 5I. SQUARE CSP Submit Document Feedback 12 TB347.26 July 16, 2015 Technical Brief 347 USER DIRECTION OF FEED NOTE: THE BUMPS (BALLS) ARE FACING DOWN IN THE POCKET MAY BE APPLICABLE ONLY FOR PRODUCTS BEFORE MAY 01, 2008 FIGURE 5J. RECTANGULAR - CSP USER DIRECTION OF FEED NOTE: ALL NEW PRODUCTS WILL FOLLOW THIS A1 (PIN 1) ORIENTATION EFFECTIVE DATE: MAY 01, 2008 FIGURE 5K. RECTANGULAR - CSP USER DIRECTION OF FEED NOTE: SPECIFICALLY FOR 8 BUMP 1.40x1.20mm CSP FIGURE 5L. RECTANGULAR - CSP USER DIRECTION OF FEED NOTE: ALL NEW PRODUCTS WILL FOLLOW THIS A1 (PIN 1) ORIENTATION EFFECTIVE DATE: MAY 01, 2008 FIGURE 5M. RECTANGULAR - HDA FIGURE 5. MECHANICAL POLARIZATION DIAGRAMS Submit Document Feedback 13 TB347.26 July 16, 2015 Technical Brief 347 EMBOSSED OR MOLDED RECYCLE SYMBOL (EXAMPLE) 40(1.575) MIN. ACCESS HOLE AT SLOT LOCATION 1.5(0.059) MIN 330mm (13.00) OR 178mm (7.00) W3 INCLUDES FLANGE DISTORTION AT OUTER EDGE W1 MEASURED AT HUB HUB DIAMETER 20.2 (0.795) MIN ARBOR HOLE 13.0(0.512) DIA. FULL RADIUS W2 MEASURED AT HUB TAPE SLOT IN CORE FOR TAPE START 2.5(0.098) MIN. WIDTH 10(0.394) MIN. DEPTH FIGURE 6. REEL DIMENSIONS TAPE WIDTH W1 (NOMINAL) W2 (MAXIMUM) W3 (MAXIMUM) 8mm (0.315) 8.4 (0.331) 14.4 (0.567) 10.9 (0.429) 12mm (0.472) 12.4 (0.488) 18.4 (0.724) 15.4 (0.606) 16mm (0.629) 16.4 (0.646) 22.4 (0.882) 19.4 (0.764) 24mm (0.945) 24.4 (0.961) 30.4 (1.197) 27.4 (1.079) 32mm (1.260) 32.4 (1.276) 38.4 (1.512) 35.4 (1.394) 44mm (1.732) 44.4 (1.748) 50.4 (1.984) 47.4 (1.866) NOTE: 26. Dimensions are in millimeters (inches are in brackets for reference only). Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that the document is current before proceeding. For information regarding Intersil Corporation and its products, see www.intersil.com Submit Document Feedback 14 TB347.26 July 16, 2015