Driver circuits for photodiode array with amplifier C9118 series Compact, easy-to-use driver circuit The C9118 series CMOS driver circuit is designed for photodiode arrays with amplifier. The C9118 series operates a linear image sensor by just inputting two signals (M-CLK and M-RESET) and a signal +5 V supply. The C9118 series is assembled on a compact board measuring 48 × 56 mm and allows downsizing of the measurement equipment. The C9118 is intended for single use or parallel connections, while the C9118-01 is suitable for cascade connections. Features Applications Single power supply (+5 V) operation Various types of image acquisition Operation with two input signals (M-CLK and M-RESET) Optical detection equipment t Compact: 48 × 56 × 5.2 mm Compatible photodiode arrays with amplifier Photodiode array with amplifier (sold separatery) Driver circuit for photodiode array with amplifier C9118 C9118-01 Type no. Element size (pitch × height) 0.8 mm × 0.8 mm 0.4 mm × 0.6 mm 0.8 mm × 0.8 mm 1.6 mm × 1.6 mm Number of elements S8865-64, S11865-64, S11865-64G S8865-128, S11865-128, S11865-128G S8866-128-02, S11866-128-02, S11866-128G-02 S11866-64-02, S11866-64G-02 64 128 128 64 Note: These circuits do not support the S8865-256, S8866-64-02, S11865-256 and S11865-256G. Absolute maximum ratings Parameter Supply voltage Digital input voltage Operating temperature Storage temperature Symbol Vcc Topr Tstg Condition Ta=25 °C Ta=25 °C Value +7 V 0 to 50*1 0 to 70*1 Unit V V °C °C *1: No condensation Note: Exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure to use the product within the absolute maximum ratings. Specifications (Ta=25 °C) Parameter Rated voltage Current consumption High level Digital input Low level M-RESET pulse width (Low level) M-CLK frequency Digital rise/fall times Data rate Offset output VIDEO saturation output*2 Symbol +Is VIH VIL TpwstRESET1 f(CLK) tTLH/tTHL fV Voffset Vsat Min. 4.9 2.0 0 10 40 10 - Typ. 5.0 75 20 0.5 4.5 Max. 5.2 80 5 0.8 4000 30 1000 - Unit V mA V V μs kHz ns kHz V V *2: From offset value www.hamamatsu.com 1 Driver circuits for photodiode array with amplifier C9118 series Block diagram (C9118-01) +Vcc Photodiode array with amplifier +Vcc SW1 CN1 CLK RESET Trig EOS EXTSP Vms Vg Vdd GND Video Vref Vp 1: TOP 2: END 1 +Vcc CN2 M-CLK M-RESET TRIGGER L-EOS IN-START GAIN +5 V GND VIDEO GND 2 Controller +Vcc +Vp VR1 SW2 CN3 +Vcc + +Vp + M-CLK M-RESET TRIGGER L-EOS EXTSP2 GAIN +5 V GND VIDEO GND + + +Vcc REF The C9118 does not have CN3. KACCC0187EH Timing chart Timing chart of first stage sensor when used singly or in cascade connection 1 2 3 14 15 16 17 18 19 20 M-CLK M-RESET TRIGGER L-EOS VIDEO Last stage sensor signal is output when used in cascade connection. Timing chart of second and subsequent stage sensors when used in cascade connection M-CLK M-RESET IN-START VIDEO signal is output right after EXTSP2 signal input from previous stage TRIGGER L-EOS VIDEO Last stage sensor signal is output when used in cascade connection KACCC0188EA 2 Driver circuits for photodiode array with amplifier C9118 series Connection examples Single or parallel readout example (C9118) Simultaneous integration/output (effective for high-speed processing) array with amplifier C9118 CN2 External input/output cable (accessory) External controller Scan direction Photodiode array with amplifier C9118 CN2 External controller Scan direction Photodiode array with amplifier C9118 CN2 External controller Scan direction KACCC0189EE Cascade readout example (C9118-01) Simultaneous integration/serial output (Simplifies external processing circuit) array with amplifier C9118-01 CN2 Scan direction External input/output cable (accessory) External controller CN3 Photodiode array with amplifier Cascade connection cable (accessory) C9118-01 CN2 CN3 Photodiode array with amplifier C9118-01 CN2 CN3 KACCC0190EF 3 3 Driver circuits for photodiode array with amplifier C9118 series Dimensional outlines (unit: mm) C9118 Driver circuit for photodiode with amplifier C9118 Photodiode array with amplifier (sold separately) 4 × (2 ×) R1.2 56 25 3 2 38 2 1 1 Scan direction CN2 48 42 51.2 10 CN1 6 12 32 8 1.6 2.5 2.5 3.6 8 * S8865-64, S8865-128, S11865-64, S11865-64G, S11865-128, S11865-128G KACCA0357EA C9118-01 Driver circuit for photodiode with amplifier C9118-01 Photodiode array with amplifier (sold separately) 4 × (2 ×) R1.2 56 25 3 2 38 2 1 1 Scan direction CN2 48 42 51.2 10 CN1 1 CN3 12 6 12 32 8 1.6 2.5 2.5 3.6 8 * S8865-64, S8865-128, S11865-64, S11865-64G, S11865-128, S11865-128G KACCA0124ED 4 Driver circuits for photodiode array with amplifier C9118 series Pin assignment of I/O connector CN1 [Connector type: 801-87-012-20-002101 PRECI-DIP (made by DURTAL) or equivalent] Pin no. 1 2 3 Terminal Name RESET CLK Trig I/O O O I 4 EXTST O 5 Vms O 6 7 8 9 10 11 12 Vdd GND EOS Video Vref Vgain Vpd O I I O O O Description Sensor scan start signal. Pulse width at High level nearly equals sensor integration time. Sensor scan sync signal. Sensor starts scanning in synchronization with this signal. For A/D conversion timing signals. Positive logic High level at first stage during parallel or serial readout. At second and subsequent stages during serial readout, this outputs the EOS pulse of preceding stage. High level at first stage during parallel or serial readout. At second and subsequent stages, this sets to Low level. Sensor supply voltage Sensor GND EOS (end of scan) signal of sensor. Negative logic Video output signal. Positive polarity Reference voltage Sensor gain switching H: high gain, L: low gain Photodiode voltage CN2 [Connector type: DF13-10P-1.25H (50) (made by Hirose Electric)] Used to connect the first stage to an external I/O during parallel readout or serial readout For the second and subsequent stages during serial readout, CN2 is used to connect to CN3 at preceding stage. Pin no. 1 2 3 4 Terminal Name M-RESET M-CLK TRIGGER L-EOS I/O I I O O 5 IN-START I 6 7 8 9 10 GAIN GND +5 V VIDEO A.GND I I O O Description Sensor scan start signal. Pulse width at High level nearly equals sensor integration time. Sensor scan sync signal. Sensor and circuit start operating in synchronization with this signal. For A/D conversion timing signals. Positive logic EOS (end of scan) signal of all sensors during parallel or serial readout. Negative logic NC (no connection) at first stage during parallel or serial readout. At second and subsequent stages during serial readout, this receives the EOS pulse of preceding stage. External setting for sensor gain H: high gain, L: low gain Circuit GND +5 V power supply Video output signal. Positive polarity Video GND CN3 [CN3 is installed only for C9118-01. Connector type: DF13-12P-1.25H (50) (made by Hirose Electric)] Used to connect to CN2 at next stage during serial readout. Pin no. 1 2 3 4 5 6 7 8 9 10 11 12 Terminal Name M-RESET M-CLK TRIGGER L-EOS EXTSP2 GAIN GND +5 V VIDEO A.GND NC NC I/O I I O O O I I O O - Description Sensor scan start signal. Pulse width at High level nearly equals sensor integration time. Sensor scan sync signal. Sensor starts scanning in synchronization with this signal. For A/D conversion timing signals. Positive logic EOS (end of scan) signal of all sensors during parallel or serial readout. Negative logic Video signal scan start signal at second stage during serial readout. Negative logic External setting for sensor gain H: high gain, L: low gain Circuit GND +5 V power supply Video output signal. Positive polarity Video GND No connection No connection Note: CN3 is installed only for serial readout. Pin no. 1 to 4 and 6 to 10 connect to the same pin No. of CN2 as common lines. 5 Driver circuits for photodiode array with amplifier C9118 series Parallel readout and serial readout settings (C9118-01) <Parallel readout setting> ON 1 2 3 4 Set SW1 and SW2 to OFF as shown at left. (SW3 and SW4 have no connection) <First stage setting for serial readout> ON 1 2 3 4 Set SW1 to OFF and SW2 to ON as shown at left. (SW3 and SW4 have no connection) <Second stage to second from last stage setting for serial readout> ON 1 2 3 4 Set SW1 and SW2 to ON as shown at left. (SW3 and SW4 have no connection) <Last stage setting for serial readout> ON 1 2 3 4 Set SW1 to ON and SW2 to OFF as shown at left. (SW3 and SW4 have no connection) KACCC0191EA 6 Driver circuits for photodiode array with amplifier C9118 series Accessory (unit: mm) C9118 External input/output cable C9118-01 ・ External input/output cable ・ Cascade connection cable ・ External input/output cable Cascade connection cable This cable connects CN2 to an external device (power supply, pulse generator, etc.). Connector: DF-13-10S-1.25C (made by Hirose Electric) Terminal: DF13-2630SCFA (gold plating) Cable: Conforms to UL1061 AWG28 [CN2] This cable connects between CN2 and CN3 for serial readout. Connector: [CN2] DF13-10S-1.25C (made by Hirose Electric) [CN3] DF13-12S-1.25C (made by Hirose Electric) Terminal: DF13-2630SCFA (gold plating) Cable: Conforms to UL1061 AWG28 [CN2] [CN3] 100 100 KACCC0198EB Pin no. 1 2 3 4 5 Color Brown Red Orange Yellow Green Pin no. 6 7 8 9 10 Color Blue Purple Gray White Black KACCC0773EA Pin no. 1 2 3 4 5 6 Color Brown Red Orange Yellow Green Blue Pin no. 7 8 9 10 11 12 Color Purple Gray White Black No cable No cable Related information www.hamamatsu.com/sp/ssd/doc_en.html Precautions ∙ Disclaimer Information described in this material is current as of April, 2015. Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the information contained is believed to be accurate. In rare cases, however, there may be inaccuracies such as text errors. Before using these products, always contact us for the delivery specification sheet to check the latest specifications. The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that one year period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product use. Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission. www.hamamatsu.com HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater, N.J. 08807, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 8152-375-0, Fax: (49) 8152-265-8 France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 16440 Kista, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moia, 1 int. 6, 20020 Arese (Milano), Italy, Telephone: (39) 02-93581733, Fax: (39) 02-93581741 China: Hamamatsu Photonics (China) Co., Ltd.: B1201, Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: (86) 10-6586-6006, Fax: (86) 10-6586-2866 Cat. No. KACC1087E12 Apr. 2015 DN 7